Digital Watchdog DWC-V4783WD User Manual

ANALOG HIGH DEFINITION
SnapIt Outdoor Dome Camera

DWC-V4783WD
DWC-V4783WTIR

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.

05/2015

PRECAUTIONS

Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

2

TABLE OF CONTENTS

Table of Contents

Introduction

Installation

Module OSD Menu

Troubleshooting

Warranty Information

Specifications

Features
Parts and Descriptions
Dimensions

Inside the Box
Installation Instructions
Wall Mount Installation Instructions

Ceiling Mount Installation Instructions
Corner Mount Installation Instructions

Connecting to Monitors 13
Control Board
Adjusting the Camera Angle

8-9

16-29

31-32

33-34

3

4
5
6

7

10
11

12

14
15

30

FEATURES*

Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
Panasonic 1/3" CMOS Sensor
1080P Resolution at 30fps
Wide Dynamic Range (WDR)
Varifocal Auto-Focus P-Iris Lens 2.8~12mm
CleanView™ Hydrophobic Dome Coating Repels Water, Dust and Grease
Smart IR™ with Intelligent Camera Sync. 70ft Range [DWC-V4783WTIR Models]
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter [DWC-V4783WTIR Models]
Auto Sensing 24VAC/12VDC with Line Lock
Secondary Video-BNC Output (While UTP in use)
Easy Icon Driven OSD Menu with Built-in Joystick
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)
Junction Box Built-in
RS-485 Built-in
IP68 Certified (Water Resistant)

4

PARTS & DESCRIPTION*

Lens

Control Board

Bubble Dome

Upper Case

Tilt Stopper Screw

Joystick for OSD Menu

Test Motitor Cable Slot

Flush Mount Base

Set Screw

Cables: BNC, UTP, RS485

Mounting Hole

Surface Mount Base

Set Screw

5

DIMENSIONS IN MILLIMETERS (IN)*

17(0.66”)
28(1.10”)

54(2.12”)

118.8(4.67”)

6

Flush Mount

137(5.39”)

101(3.97”)

Surface Mount

139(5.47”)

98.8(3.88”)

36(1.41”)

29(1.14”)

53.8(2.11”)

Top View

139(5.47”)

121(4.76”)

121(4.76”)

INSIDE THE BOX*

Included with your camera:

Camera

Template Sheet

User’s Manual

DC Plug Cable

Cables

Screw &

Plastic Anchor-2pcs

Test Monitor Calbe

Hexagonal Wrench

(for tighten Set Screw)

Torx Screw Driver

7

INSTALLATION*

1. Use the included T-wrench to remove the
camera’s dome from the camerta module.

2. To detach the cameremodule from the junction
box, use a phillips head screw driver to loosen the
three screws on the module case. The camera’s
module will be secured to the junction box with the
security cable.

3. Use the mounting template or your camera’s
junction box and drill the necessary mounting
holes to the mounting surface.

3. Pull Wires through and make connections.

4. Mount the camera to the mounting surface using
the included screws.

8

UTP

RS485

DC 12V

AC 24V

If you need to keep the wiring within the
camera housing, refer to the diagram above.

INSTALLATION*

5. Adjust the camera’s lens position by using the 3-Axis gimbal.

6. Snap the camera dome over the camera module to complete the installation.

Flush Mount Installation

For a flush mount housing, remove the surface mount
base (junction box). Cut a large hole on the mounting
surface for the top part of the flush mount base.
Use the three screws fixed to the base to secure it to
the mounting surface. Follow steps 4 through 6 to
complete the installation.

ST4X35

9

INSTALLATION - WALL MOUNT*

1. Verify all parts are in the box.

4. Attach the camera’s surface
mount base (junction box) to
the wall mount.

10

2. Insert the wires from the
camera through the wall
mount housing.

5. Connect all cables and snap
the camera module onto the
base.

3. Use the mounting template to
make pilot holes. Use the dry
wall anchors and woods screws
to attach the assembly.

6. Adjust the camera and
secure the dome cover over
the camera module.

INSTALLATION - CEILING MOUNT*

1. Verify all parts are in the box.

4. Use the mounting template
to make pilot holes. Use the
dry wall anchors and wood
screws to attach the assembly
to the wall.

2. Attach the top shield to the
pendant mount.

5. Connect all cables and verify
camera is operating properly.

3. Run all necessary cables
from the ceiling to the mount.

6. Attach the camera to the
ceiling mount and secure the
dome cover properly.

11

INSTALLATION - CORNER MOUNT*

1. Verify all parts are in the box.

2. Attach the two compression fittings to the
corner bracket.

3. Attach the wall mount bracket to the corner
mount using the machine screws.

12

4. Mount the camera assembly to the corner of
the wall, using wall mount anchors and
machine screws.

CONNECTING TO MONITORS*

Use the diagram below to connect to a Monitor or CRT Monitor properly.

DC 12V / AC 24V

CCTV Monitor

Left

Down

2nd Video Output

Monitor

300.0

Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.

Up

Right

13

ADJUSTING THE CAMERA ANGLE*

The Gimbal mechanism yields maximum rotation and placement as show below.

Rotation 360 Panning 360

75

14

MODULE OSD MENU*

EXPOSURE

LENS

MANUAL / AUTO

BACKLIGHT

OFF / HME / BLC / WDR

DRC

OFF / LOW / MIDDLE / HIGH

DEFOG

OFF / ON

AGC

0~10

STARLIGHT

OFF / x2 ~ x32

3D DNR

OFF / LOW / MIDDLE / HIGH

EXIT JUMP

SAVE & EXIT / EXIT

MOTION

MOTION

OFF / ON

DET. WINDOWS
SENSITIVITY

0 ~ 10

MOTION OSD

OFF / ON

TEXT ALARM

OFF / ON

SIGNAL OUT

OFF / ON

EXIT JUMP

SAVE & EXIT / EXIT

COLOR

WB BAL.

AUTO / AUTO-EX / PRESET
/ MANULAL

COLOR GAIN

0 ~ 20

EXIT JUMP

SAVE & EXIT / EXIT

PRIVACY

BOX

OFF / ON

POLYGON

OFF / ON

EXIT JUMP

SAVE & EXIT / EXIT

DAY & NIGHT

D&N MODE

AUTO / COLOR / BW / EXTERN

AGC THRES

0 ~ 20

AGC MARGIN

0 ~ 20

EXT LED

OFF / AUTO

DELAY

LOW / MIDDLE / HIGH

SMART IR

0 ~ 20

EXIT JUMP

SAVE & EXIT / EXIT

SETUP

COMMUNICA.
CAM TITLE

OFF / ON

IMAGE RANGE

FULL / COMP / USER

FRAME RATE

720_50P/60P / 720_25P/30P
/ 1080_25P/30P

FREQUENCY

50Hz / 60Hz

LANGUAGE

ENG / CHN / CHN (S) / JPN / KOR

DEFECT DET

ON

INITIAL

ON

EXIT JUMP

SAVE & EXIT / EXIT

FUNCTION

SHARPNESS

0 ~ 10

GAMMA

0.45 ~ 0.75

MIRROR

OFF / ON

FLIP

OFF / ON

D. ZOOM

x1.0 ~ x16.0

EXIT JUMP

SAVE & EXIT / EXIT

EXIT

SAVE
RESTORE

EXIT

15

EXPOSURE

LENS

MANUAL/ Manual mode supports the fixed board lens or the manual iris lens.
AUTO AUTO mode sets the camera’s iris automatically.

- Level: Set the lens mode to Normal or Deblur.

- Brightness: Adjust the camera’s brightness from 0~10. The higher the number, the brighter the
image will appear.

- Shutter: Set the shutter speed to AUTO, Manual, or FLC (Flicker-less mode).

- If AUTO is selected, select from the following options:

- NORMAL: Set when the camera is installed in an indoor environment.

- DEBLUR: Set when the camera is installed in an outdoor envirnment.

- Select FLC if the camera is experiencing some flickering in the image.

- If Manual is selected, set the shutter speed from 1/30(1/25),1/60(1/50), 1/120(1/100) ~ 1/30000.

16

EXPOSURE

2-MOTIR

This menu allows you to setup the lens’ motor options.

- AF MODE

- AUTO: FoV and Lens focus will be set automatically.

- MANUAL: ZOOM IN/OUT (Using Top/Bottom button
on OSD joystick) and Focus (Using Left/Right button on OSD
joystick) can be set manually

- SCANNING: If the focus is not adjusted iwhen Half Model is
selected, change the Scanning value to Full Mode to adjust the
focus.

- ONEPUSHAF: Run the Auto Focus at the camera’s current FoV.

- SYNC TDN : When enabled, the camera’s AF will reset when the
camera switches between day and night.

- INITIAL: Reset Two Motor Lens

- AF TIMMER: Run the Auto Focus after the set time (1~3 min).

17

EXPOSURE

BACKLIGHT
OFF
HME HIGHLIGHT MASKING EXPOSURE

HME allows objects to appear clearly on the screen by
masking extremely bright areas. To setup HME, set the
level and color. The lower the setting, the darker the
masking areas have to be. Select from: 0 ~ 10.
Color: Set the color of the HME mask. Select from:
BLACK / WHITE / YELLOW / CYAN / GREEN /
MAGENTA / RED / BLUE

BLC BACK LIGHT COMPENSATION

If BLC is selected, adjust the size nad position of the mask:

- H-POS: Move the Zone position left or right. The higher the number,
the zone will move to the right.

- V-POS: Move the Zone position up or down. The higher the number,
the zone will move down.

- H-Size: Reset the zone‘s size horizontally. The higher the number,
the right side panel will move further to the right.

- V-Size: Reset the zone’s size vertically. The higher the number, the
bottom side panel will move further down.

WDR Wide Dynamic Range

If WDR is selected, adjust the WDR level (Weight) in the submenu. Select
from Low, Middle, or High (Default).

18

EXPOSURE

DRC DYNAMIC RANGE COMPRESSOR

DRC enables dark areas in images to become more visible without overexposing the

bright areas to create one perfect image. Select from: OFF / ON.
NOTE: If WDR or DEFOG are enabled, the DRC settings are set automatically and will not be available
for adjustment.

DEFOG Allows the camera to process a scene that is obscured by fog or weather conditions

and provides a visibly improved image.
AUTO / Manual: Select AUTO to have the WDR and DRC levels adjusted automatically.
Set the DEFOG level from LOW / MIDDLE / HIGH.

AGC AUTO GAIN CONTROL

0~10 AGC enhances the picture brightness in low light conditions. A higher level AGC
setting makes the images brighter; however, it could increase the amount of noise.

STARLIGHT Automatically activates slow shutter function when the image is too dark.

OFF / x2 ~ x34 High values are not recommended as they may causes the image to lag.
(Default: X4) Starlight menu cannot be controlled if the SHUTTER setting is above 1/60.

3D DNR 3D DIGITAL NOISE REDUCTION

OFF/ LOW/ 3D-DNR reduces the noise on the screen in low light conditions and
MID/ HIGH allows for clearer images, even at night.

19

COLOR

WB MODE

ATW Auto Tracking White Balance Control mode compensates for color temperature changes

between 2400K

AWB Auto White Balance Control mode compensates for color temperature changes

lower than 2000K

PUSH Push fixes the white balance based on the current lighting automatically.
MANUAL Users can control the white balance manually by changing RED GAIN and BLUE

GAIN (see below).
C-TEMP: Select the color temperature for the white balance setup. If enabled,
the Red and Blue Gain settings will be set automatically according to the
C-TEMP selected.
RED GAIN: 0 ~ 20. Adjusts the amount of red in the image.
BLUE GAIN: 0 ~ 20. Adjust the amount of blue in the image.

COLOR GAIN

Set the color gain from 0~20.

20

o

and 11000Ko.

o

and higher than 15000Ko.

DAY & NIGHT

D&N MODE

AUTO / Day/ Night switch will be based on the AGC levels.
COLOR / The camera always stays in day/color mode.
B&W The camera always stays in night/B&W mode.
EXTERN Day/ Night switch will be based on using IR LED lights.

AUTO:

- AGC Threshold: Set when the camera switches between Day & Night.

- AGC Margin: Set the value added to the AGC Threshold. Adjust the
value based on the environment in which the camera is installed. If the
margin is too low, the camera will switch from color to B/W and back.
EXT.:

- CDS Threshold: Marks the light level at which the camera will switch between color and B/W.
The lower the value, the camera will require less light (more
darkness) to switch to Night Mode.

- CDS Margin: The value added to the CDS Threshold. Adjust this
based on the environment in which the camera is installed. If the
margin is too low, the camera will switch from color to B/W and back.

EXT LED

AUTO / AUTO: The LEDs are enabled/ disabled by the CDS Sensor on the LED Board.
OFF OFF: The camera’s LEDs are disabled manually.

DELAY

Low/Mid/High Time interval delay before switching from day mode to night mode.

SMART IR

0 ~ 20 Enable Smart IR and set the level. Higher values will make Smart IR stronger.

21

FUNCTION

SHARPNESS

0 ~ 10 Sets the image sharpness. The higher the number, the sharper the image.

GAMMA

0.45 ~ 0.75 Select the desired gamma level. 0.55 is default setting.

MIRROR / FLIP

OFF
MIRROR Reflects the camera horizontally.

FLIP Reflects the camera vertically.

Mirror & Flip ONFlip ONMirror ONMirror / Flip OFF

D-Zoom

x1 ~ x16 Enable or Disable Digital zoom to the camera’s field of view. By default, the zoom

will go to the center of the camera’s Field of View.

22

MOTION

The camera can detect the movement and display an alarm on the screen when movement is detected.

MOTION To use the motion detection settings, be fore Motion is ON.
DET. WINDOW

- Window Use: Select which zone to setup from the 4 motion zones available.

- Window Zone: Enable or disable the selected motion zone.

- DET H-POS: Move the Zone left or right. The higher the number, the zone will move to the right.

- DET V-POS: Move the Zone up or down. The higher the number, the
zone will move down.

- DET H-Size: Adjust the zone‘s size horizontally. The higher the number,
the right side panel will move further to the right.

- DET V-Size: Adjust the zone’s size vertically. The higher the number, the
bottom side panel will move further down.

SENSITIVITY

The smaller the movement you want to detect, the higher the sensitivity value must be.

MOTION OSD

If enabled, the text MOTION ZONE will appear on the screen indicating the area of motion detection.

TEXT ALARM

Setup a text to appear on the screen when motion is detected explaining the alarm situation.

- WINDOW MOTION: Wiil appear when a motion alarm is detected.

- CAMERA MOVING: Will appear if the camera is shaken abruptly.

- BRIGHT CHANGE: Will appear if the brighness in the scene changes suddenly and drstically.

SIGNAL OUT

If enabled, the camera can trigger an output when motion is detected.

23

PRIVACY

You can hide some parts of the screen for privacy masking. A total of 8 different privacy masking
zones are available. The cameras support square privacy masks or advanced polygon masks.

BOX MASKS

- ZONE NUM.: Select the zone number you want to setup.

- ZONE DISP.: To enable it, turn the display option ON.

- H-POS: Move the Zone position Left or right. The higher the
number, the zone will move to the right.

- V-POS: Move the Zone position up or down. The higher the
number, the zone will move down.

- H-SIZE: Reset the zone‘s size horizontally. The higher the
number, the right side panel will move further to the right.

- V-SIZE: Reset the zone’s size vertically. The higher the number,
the bottom side panel will move further down.

- Y LEVEL- The higher the number, the brighter the color will appear.

- CR LEVEL- The higher the number, the more red tone will be added to the zone’s color.
The lower the number, the more green will be added to the zone’s color.

- CB LEVEL- High CB Level + High CR Level = Red
High CB Level + Low CR Level = Blue
Low CB Level + High CR Level = Orange

24

PRIVACY

You can hide some parts of the screen for privacy masking. A total of 8 different privacy masking
zones are available. The cameras support square privacy masks or advanced polygon masks.

POLYGON MASKS

- ZONE NUM.: Select the zone number you want to setup.

- ZONE DISP.: To enable it, turn the display option ON.

-POS0-X: Move the mask’s upper left angle left to right.

-POS0-Y: Move the mask’s upper left angle up and down.

-POS1-X: Move the mask’s upper right angle left to right.

-POS1-Y: Move the mask’s upper right angle up and down.

-POS2-X: Move the mask’s lower right angle left to right.

-POS2-Y: Move the mask’s lower right angle up and down.

-POS3-X: Move the mask’s lower left angle left to right.

-POS3-Y: Move the mask’s lower left angle up and down.

- Y LEVEL- The higher the number, the brighter the color will appear.

- CR LEVEL- The higher the number, the more red tone will be added to the zone’s color.
The lower the number, the more green will be added to the zone’s color.

- CB LEVEL- High CB Level + High CR Level = Red
High CB Level + Low CR Level = Blue
Low CB Level + High CR Level = Orange

25

SETUP

COMMUNICATION

Adjust the camera’s ID and Baudrate. Default Protocol is Pelco-D.

- CAM ID: Provide an ID number for the camera (0 ~ 255).

- BAUDRATE: 9600bps is default. Select the baudrate from the
following options: 2400/4800/9600/57600/115200 bps.

CAM. TITLE

Add a name to the camera. Set the title by using the OSD joystick.

IMAGE RANGE

Image Range allows you to set the proper Black and White levels
according to the external display you use.
FULL: Display all BLACK level and WHITE level without
compression.
COMP: Display BLACK level and WHITE level with compression.
USER : Reset the BLACK level by changing the OFFSET value.

26

SETUP

FRAME RATE

Set the camera’s display frame rate and resolution. Select from:
720-30P, 720-60P, 1080-30P. The camera may have to be
rebooted after frame rate change.

FREQUENCY

When the camera’s image appears to have flickering issues,
change the frequency value to adjust the image.

LANGUAGE

Select from the following: English (Default), Chinese, Chinese (S),
Japanese, and Koran.

DEFECT DET.

The camera can detect and correct dead pixels in the image. Press
the select button and set the threshold level. The camera will
detect and adjust the pixels automatically.

INITIAL

Reset the camera to its default settings. Press and hold the select
button for five (5) seconds.

27

EXIT

EXIT
SAVE Exit the OSD menu after saving the recent changes.
INITIAL Exit the OSD menu after resetting the camera to factory default.

28

TROUBLESHOOTING

Before sending your camera for repair, check the following or contact our technical
specialist.

FOR NO VIDEO

Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the camera’s OSD menu.
Check the power supply and make sure the camera has the proper voltage and
current.

FOR OUT-OF-FOCUS VIDEO

Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and
gently clean. Check the lens’ manual focal and zoom adjustment. The use of a field
test monitor is recommended.

29

WARRANTY INFORMATION*

Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera
against defects in materials or workmanship as follows:

LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase
date, if the camera is determined to be defective, the Warrantor will repair or replace the
unit with a new or refurbished product at its option at no charge.

PARTS: In addition, the Warrantor will supply replacement parts for the initial five (5) years
and one (1) year on IR LED.

To obtain warranty or out of warranty service, please contact a Technical Support
Representative at 1-866-446-3595 Monday through Friday from 9:00AM to 8:00PM
Eastern Standard Time.

A purchase receipt or other proof of the original purchase date is required before warranty
service is rendered. This warranty only covers failures due to defects in materials and
workmanship which arise during normal use. This warranty does not cover damage which
occurs in shipment or failures which are caused by products not supplied by the Warrantor or
failures which result from accident, misuse, abuse, neglect, mishandling, misapplication,
alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate
signal pickup, maladjustment of consumer controls, improper operation, power line surge,
improper voltage supply, lightning damage, rental use of the product or service by anyone other
than an authorized repair facility or damage that is attributable to acts of God.

30

LIMITS & EXCLUSIONS*

There are no express warranties except as listed. The warrantor will not be liable for incidental
or consequential damages (including damage to recording media without limitation) resulting
from the use of these products or arising out of any breach of the warranty. All express and
implied warranties, including the warranties of merchantability and fitness for particular
purpose, are limited to the applicable warranty period set forth above.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitatons on how long an implied warranty lasts, so the exclusions or limitations listed above
may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights that vary from state-to-state.

If the problem is not handled to your satisfaction, then write to the following address:
Digital Watchdog, Inc.

ATTN: RMA Department
5436 W. Crenshaw Street
Tampa, FL 33634

Service calls which do not involve defective materials or workmanship as determined by the
Warrantor, in its sole discretion, are not covered. Costs of such service calls are the
responsibility of the purchaser.

31

SPECIFICATIONS*

VIDEO

Image Sensor Panasonic 1/3" CMOS
Active Pixels 1944(H) x 1092(V)
Scanning System Progressive scan
Frequency 60Hz/50Hz
Signal Technology 2.0 Megapixel AHD
Synchronization Internal
Resolution 1920x1080 (1080p)
Minimum Scene Illumination F1.4 (30IRE): 0.35Lux [Color]
F1.4 (30IRE): 0 Lux [B&W]
S/N Ratio 55dB
Video Output AHD 1080p30fps/720p60fps/720p30fps
Alarm Output 1 Alarm Output

LENS

Focal Length 2.8 ~ 12mm
Lens Type P-Iris Auto Focus
IR Distance 70ft [V4783WTIR]

OPERATIONAL

Shutter Speed 1/30(25)-1/30,000
Backlight Off/ On
STAR-LIGHT OFF, x2 -x32
Wide Dynamic Range (WDR) Off/ On

32

SPECIFICATIONS*

OPERATIONAL (CONT.)

Digital Noise Reduction Off, Low, Middle, High
White Balance Auto / Auto-Ex/ Preset / Manual
Day and Night Day/ Night/ Auto
Auto Gain Control Max 60dB
Privacy Zones 24 Privacy Zones
RS485/ UTP Built-in PELCO D/PELCO C
Digital Zoom x1.0 ~ x16.0

ENVIRONMENTAL

Operating Temperature -20°C ~ 50°C (-4°F ~ 122°F)
Operating Humidity No more than 90% (Non-Condensing)
IP Rating IP68 (Water Resistant)
Other Certifications FCC, CE, ROHS

ELECTRICAL

Power Requirements DC12V/AC24V Dual Voltage
Power V4783WD DC12V: 3.43W, 286mA
AC24V: 3.3W, 198mA
V4783WTIR DC12V: 3.43W, 286mA, LED On: 6.45W, 537mA
AC24V: 3.3W, 137mA, LED On: 5.95W, 372mA

MECHANICAL

Housing Material and Dimensions Aluminum, 139 X 118.8 mm ( 5.47 X 4.7 in)
Weight 2.028 lbs [V4783WD], 2.5 lbs [V4783WTIR]

33

MEMO*

34

MEMO*

35

5436 W Crenshaw St. Tampa, FL 33634

Tel : [phone]

Fax : [phone]

www.Digital-Watchdog.com

[e-mail]

Technical Support Hours : Monday-Friday

9:00am to 8:00pm EST