Digital Watchdog DWC-V4365T User Manual

PIXIM Vandal-Proof Dome Camera

DWC-V4365T

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.

07062012

PRECAUTIONS

Do not open or modify. Do not open the case except during maintenence and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust. Protect from high temperature. Be careful when installing near the ceiling of kitchen or a boiler room, as the temperature may rise to high levels. Cleaning: To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe. Mounting Surface: The material of the mounting surface must be strong enough to support the camera.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference, when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

TABLE OF CONTENTS

Introduction

Installation

Module OSD Menu

Troubleshooting

Warranty Information

Specifications

Features

Parts and Descriptions

Dimensions

Inside the Box

Mount Installation Instructions

Connecting to Monitors

Adjusting the Camera Lens

Adjusting the 3-Axis Gimbal 17

8-13

14-15

18-29

31-32

33-36

FEATURES*

1/3” PIXIM Nightwolf CMOS Sensor

690 Horizontal TV Lines

3.3~12mm Varifocal Auto Iris Lens

TDN (True Day and Night / IR Cut Filter)

3D DNR (Digital Noise Reduction)

Powerful Wide Dynamic Range

Star-Light (Super Low Light Technology)

8X Digital Zoom

Ultra Low Light Sensitivity

Smear Cancelation

Low Power Consumption

Programmable Privacy Zones (6) & Motion Detection

AGC/ BLC/ AWB

OSD Menu with Built-In Joystick

IP68 Certified

Junction Box Included

UTP & RS485 Built-In

Auto Sensing 12VDC or 24VAC with Line Lock

Secondary Video-BNC Output

PART & DESCRIPTIONS*

Lens

Power Input Connector (Dual Voltage)

UTP

RS-485

Primary Video-BNC Output Connector

Camera Control Board

Bubble Dome Cover

Upper Case

Flush Mount Base

Surface Mount Base / Junction Box

Assembly Screws (#8 - 32 x 0.75)

Secondary Video-BNC Output Connector

Safety Wire

Mounting Screws

NO IR

DIMENSIONS IN MILLIMETERS (IN)*

Flush Mount

137(5.39”)

101(3.98”)

17(0.67”)

28(1.1”)

98.8(3.89”)

54(2.13”)

Surface Mount

139(5.47”)139(5.47”)

36(1.42”)

118.8

(4.68”)

29(1.41”)

53.8(2.12”)

121

(4.76”)

121

(4.76”)

INSIDE THE BOX*

Included with Snapit Vandal Dome Camera

User Manual

Mounting Template

4 Machine Screws and 4 Dry Wall Anchors

TORX-T20 Wrench

L-Wrench TORX-T20 Bolt DC Plug Secondary Video-BNC Cable

7 8

SURFACE MOUNT INSTALLATION INSTRUCTIONS*

1 2 3

Use the camera’s mounting template or your camera to mark the holes as required.

Drill holes into the drywall and insert the drywall mounts into the holes.

UTP

DC 12V

RS485

AC 24V

UTP

DC 12V

RS485

AC 24V

Mount the surface mount

Route wiring behind the inner posts (dark gray area).

base (junction box) to the wall.

Pull wires through and make connections.

If you need to keep the wiring within the camera housing, refer to the diagram below.

To use the side conduit, remove the security screw with the supplied

3.0mm Allen key, and unscrew the conduit plug.

Snap the camera module onto the base by aligning the red and black markings on the base and the camera module.

6 7 8

Secure the three (3) assembly screws.

Adjust the camera’s position by using the 3-Axis Gimbal.

Tighten the three locking screws in with the L-Wrench to secure the dome cover over the camera.

FLUSH MOUNT INSTALLATION INSTRUCTIONS*

For a flush mount housing, detach the surface mount base, which is also known as the junction box, from the flush mount base.

Use the mounting template to mark the holes for the screws and a larger hole for the top extruded component of the flush mount base.

The three assembly screws (ST4X35) fixed to the flush mount base should be used to mount the camera to the surface of the wall or ceiling.

3 4 5

Secure the three (3) assembly screws.

Adjust the camera’s position by using the 3-Axis Gimbal.

ST4X35

Tighten the three locking screws in with the L-Wrench to secure the dome cover over the camera.

WALL MOUNT INSTALLATION INSTRUCTIONS*

1 2 3

Check to see all parts are in the box.

4 5 6

Attach the camera’s surface mount base (junction box) to the wall mount.

Insert the wires from the camera through the wall mount housing.

Connect all cables and snap the camera module onto the base.

Use the mounting template to make pilot holes. Use the dry wall anchors and machine screws to attach the assembly.

Adjust the camera and secure the dome cover over the camera module.

PENDANT MOUNT INSTALLATION INSTRUCTIONS*

1 2 3

Check to see all parts are in the box.

4 5 6

Use the mounting template to make pilot holes. Use the

Attach the top shield to the pendant mount.

Connect all cables and verify

camera is operating properly. dry wall anchors and machine screws to attach the assembly to the wall.

Run all necessary cables from the ceiling to the mount.

Attach the camera to the ceiling mount and secure the dome cover properly.

CORNER MOUNT INSTALLATION INSTRUCTIONS*

1 2

Check to see all parts are in the box.

3 4

Attach the wall mount bracket to the corner mount using the machine screws.

Attach the two compression fittings to the corner bracket.

Mount the camera assembly to the corner of the wall, using wall mount anchors and machine screws.

CONNECTING TO MONITORS*

Use the diagram below to connect to a Monitor or CRT Monitor properly.

DC 12V / AC 24V

CCTV Monitor

NO IRIR

Second Video Output

300.0mm(11.8”)

Monitor

Power Connection: 12VDC & 24VDC Dual Voltage (Auto Polarity Detection and Protection) All cameras are equipped with a second video output for on-site configuration.

UTP SYSTEM*

Passive to Passive

Including the Passive UTP

Passive to Active

Including the Passive UTP

UTP Cable (Max.300ft)

UTP Cable (Max 3,000ft)

Passive UTP

Active UTP

Monitor

DVR(Digital Video Recorder)

Monitor

DVR(Digital Video Recorder)

ADJUSTING THE CAMERA LENS*

Follow the instructions provided below to make any lens adjustments.

Focus

Zoom

ZOOM: TELE - WIDE

NO IR

FOCUS: FAR - NEAR

Loosen the zoom and focus handles by rotating them counter-clockwise.

Adjust the field of view by moving the handle RIGHT (TELE) to zoom in or LEFT (WIDE) to zoom out.

After the desired zoom position has been established, adjust the Focus the same way as described above.

Once the desired adjustments have been made, tighten the handles back by turning them clockwise.

ADJUSTING THE 3-AXIS GIMBAL*

The Gimbal mechanism yields maximum rotation and placement as shown below.

NO IR

Rotation 360

NO IR

Tilting 90

NO IR

Panning 360

Tilting 82

MODULE OSD MENU*

EXPOSURE (EXP) COLOR (RGB) FUNCTION (FUN)

LENS

MANUAL / DC

AE PREFERENCE

OUTDOOR / INDOOR

BLC

OFF / ON

WDR

LOW / NORMAL / MEDIUM / HIGH / CUSTOM

AGC

LOW / MEDIUM / HIGH

STARLIGHT

OFF 2X 30FPS ~ X64

METER ZONE

ADJUST ZONE1 / ADJUST ZONE2

EXIT JUMP

SAVE & EXIT / EXIT

WB MODE

AWC / ATW / PUSH LOCK / MANUAL

COLOR GAIN

-8 ~ 8

EXIT JUMP

SAVE & EXIT / EXIT

MOTION (MOT) PRIVACY (PRI)

MOTION

OFF / ON

MOTION ZONES

1 / 1~2 / 1~3 / 1~4 ADJUST ZONE 1 ADJUST ZONE 2 ADJUST ZONE 3 ADJUST ZONE 4 RETURN

EXIT JUMP

SAVE & EXIT / EXIT

PRIVICY MASK

OFF / ON (AREA 1~6)

RETURN

MASK COLOR

WHITE / BLACK / RED

EXIT JUMP

SAVE & EXIT / EXIT

DAY NIGHT (D&N)

D&N MODE

AUTO / COLOR / BW

BW BURST

OFF / ON

EXIT JUMP

SAVE & EXIT / EXIT

SYNC (SYC)

INT 1 INT 2

OFF / AUTO

LL LIMIT (0.25% / 0.50% / 1.00% / 5.00%) V PHASE(0~624) RETURN

EXIT JUMP

SAVE & EXIT / EXIT

MIRROR

OFF / MIRROR / V-FLIP / ROTATE

SHARPNESS

-8 ~ 8

GAMMA

25(0.25) ~ 100(1.0)

3DNR

OFF / LOW / MEDIUM / HIGH

D-ZOOM

ZOOM / PAN / TILT

EXIT JUMP

SAVE & EXIT / EXIT

SETUP (SET)

PC CONTROL

CAM ID(1~255) / PROTOCOL /

BAUDRATE / RETURN

TITLE

OFF / ON

LANGUAGE

ENGLISH / DEUTSCH / FRANCAIS / ITALIAN / ESPANOL / DUTCH

OMNI LENS

ALARM / READ TIEM /ALRAM ZOOM / STAND BY / RETURN

FLUORESCENT

OFF / CRR / CRR2

DIGITAL VIDEO OUTPUT

DIGITAL OUT / FIELD ORDER / FRAME

RPT / RETURN

EXIT JUMP

SAVE & EXIT / EXIT

EXIT (EXT)

EXIT SAVE & EXIT FACTORY SET

EXPOSURE (EXP)

LENS

MANUAL: Manual iris or Fixed board lens.

DC: Auto-iris Varifocal lens.

FOCUST METER helps you to find the clear focus. When the dark line alligns with the gray bar, the camera will be adjusting the focus. When it’s set on the maximum, you get the clear image.

DC mode is supported for Auto-iris Varifocal lens.

Set the Focus Meter to maximum.

- Set the lens Focus Meter to maximum (See above for more information).

- DC GAIN is to adjust Iris speed. recommended to set the AUTO Gain to 120.

- AI THOLD is to define gain level.

0 ~ 255. It is

-48 ~ 60.

EXPOSURE (EXP)

AE PREFERENCE

Auto Exposure Set AE PREFERENCE depending on the environment in which the camera is installed. Select from the following options:

INDOOR / OUTDOOR

BLC

Backlight compensation prevents subjects in defined areas from appearing too dark when backlighting is present.

If BLC is enabled, adjust the SHADOW GAIN as desired.

SHADOW GAIN (10~50) The higher the number, the stronger the BLC masking.

EXPOSURE

WDR (Wide Dynamic Range)

Enables the camera to capture clear images in the same frame, even when there are both very bright and very dark areas in the same field.Select from the following options:

LOW / NORMAL / MEDIUM(Factory Default) / HIGH/ CUSTOM

WDR OFF WDR ON

If CUSTOM is selected, adjust the Bias / Limit as you wish.

- BIAS (-30~30): Decide the WDR level in the range of LIMIT. The higher the number, the stronger the WDR adjustment.

- LIMIT (0~36): Decide the range of WDR effect level. 0 means WDR is OFF. The higher the number, the stronger the WDR will be.

EXPOSURE

EXPOSURE (EXP)

AGC (Auto Gain Control)

Auto Gain Control automatically adjusts the video gain to enhance picture brightness in low light conditions.The higher number the better sensitivity. However, higher settings mean more digital noise in the image.

LOW / MEDIUM / HIGH(Factory Default)

Select one of the options.

STARLIGHT

Starlight mode automatically activates slow shutter function when the image is too dark. You can adjust the frame integration level from X2-30FPS ~ X64**. x2 - 30FPS is the default.

**Note: Increase the setting may cause the image to lag.**

EXPOSURE (EXP)

METER ZONE

Defines an area in the image where the AE and WB settings will be applied. This option is useful when a camera is installed in an environment such as an ATM.

You can setup up to two (2) zones.

1. Select the zone you wish to adjust and enter edit mode.

2. The zone’s borders will appear in white. Use the camera’s joystick contrller to move the zone across the image. When the zone’s desired position is achieved, press the joystick controller.

3. The zone’s borders will appear in green. Use the camera’s joystick controller to increase the size of the zone. a. Moving the joystick to the right will move the zone’s right border further to the right. b. Moving the joystivk to the left will move the zone’s left border further to the left. c. Moving the joystivk up will move the zone’s top border further up. e. Moving the joystivk down will move the zone’s bottom border further down.

4. Press the joystick again. The zone’s borders will appear red. Use this option to reduce the size of the zone. a. Moving the joystick to the right will move the zone’s left border further to the right. b. Moving the joystivk to the left will move the zone’s right border further to the left. c. Moving the joystivk up will move the zone’s bottom border further up. e. Moving the joystivk down will move the zone’s top border further down.

5. To exit edit mode, press & hold the camera’s joystick controller for three (3) seconds.

EXIT_JUMP

Go to the Exit menu to save & exit, or exit without saving

COLOR (RGB)

WB MODE

Select on of the options:

AWC - Auto White Balance Control mode compensates for color temperature changes between 2000K and 18000K.

ATW- Auto Tracking White Balance Control mode compensates for color temperature changes between 2500K and 9500K. It is recommended to set the low level to 2.5K, and the high tp 11K. PUSH LOCK- Pushlock is to fix the white balance based on current lighting.

MANUAL**- Users can control the white balance manually by changing RED GAIN and BLUE GAIN (see below). KELVIN (2K~11K) The lower the number, the cooler the image will appear. The higher the number, the warmer the image will appear. R-GAIN (-20~20) Adjusts the amount of red in the image. The higher the number, the image will appear red. The lower the number, the image will appear green. B-GAIN (-20~20)- Adjusts the amount of blue in the image. The higher the number, the image will appear blue. The lower the number, the image will appear yellow.

The color temperature level that will trigger the AWB.

COLOR GAIN

It’s to adjust the amount of color in the image.

-8 (complete B/W) ~ 8 (Full Color) (Factory setting is 0.)

EXIT_JUMP

Go to the Exit menu to save & exit, or exit without saving

**All user properties will be written to ROM.**

DAY NIGHT (D&N)

D&N MODE

BW BURST**

AUTO

If AUTO is selected, the camera will automatically switch between color and B/W depending on the levels of light available. The in color mode when there is enough light. The camera will switch to B&W at night or other low light environments. settings:

READ TIME (3~255): Time interval delay before switching from day mode to night mode. It is adjustable from 3 seconds to 255 seconds.

S LEVEL (Color -> B/W) (0~60): Adjusts the light level at which the camera switches from day (color) to night (B&W) mode. The higher the number, the lower the light level.

E LEVEL (B/W -> Color) (0~60): Adjusts the light level at which the camera switches from night (B&W) to day (color) mode. This number should be lower than the value of COLOR->B&W above.

BW AGC (0~60): You can fix the Gain levels when the camera switches between Color and B/W.

COLOR

OFF

Camera always stays in day mode.

Camera always stays in night mode.

Remove BURST when converting to B/W.

Output BURST when converting to B/W.

EXIT_JUMP

Go to the Exit menu to save & exit, or exit without saving

**BW BURST available only if Day/ Night Mode is set to AUTO.**

camera will stay

Please define the following

FUNCTION (FUN)

Flips the imge horizontally / vertically or both(rotate).

OFF / MIRROR / V-FLIP / ROTATE

Sets the image’s sharpness. The higher the number, the sharper lines and details will appear in the image. However, the sharper the image, the more digital noise will be visible.

Select the desired gamma level.

25~100 (45 is default.)

3D-DNR (Digital Noise Reduction)

MIRROR

SHARPNESS

-8~8 (-4 Default)

GAMMA

3D-DNR reduces the noise on the screen in low light conditions and allows for clearer images, even at night. Select from the following options:

OFF / LOW / MEDIUM / HIGH

3D-DNR OFF 3D-DNR ON

D-ZOOM

EXIT_JUMP

Go to the Exit menu to save & exit, or exit without saving

**Note: Pan & Tilt Setup options are disabled for this camera module.**

The digital zoom function zooms to the center of the image by default. Set the Zoom level from 1~ X8. This menu also allows you adjust the camera’s Pan and Tilt.**

MOTION (MOT)

MOTION

The camera can detect the movement and display an alarm on the screen when movement is detected.

OFF / ON If Motion is enabled, you can setup the ACTIVITY THRESHOLD. This setups the camera’s sensitivity to movement. The higher the number the camera will be more sensitive to smaller movements. Select from 0 ~ 255.

When motion is enabled, “ALARM!” will appear on the top

SET MOTION ZONE

Select from four (4) available zones. To display them, select : 1 Zones- Activate only the first zone. 1-2 Zones- Activat zones 1 & 2. 1-3 Zones- Activate zones 1, 2, & 3. 1-4 Zones- Activate all zones. To edit a motion zone:

1. Select the zone you want to setup. The selected zone’s botrders will appear in white.

2. Using your joystick, move the zone to the desired area.

3. Press the joystick to adjust the zone’s size. The zone’s borders will be green. a. Move the joystick to the right to move the zone’s right border further to the right. b. Move the joystivk to the left to move the zone’s left border further to the left. c. Move the joystivk up to move the zone’s top border further up. e. Moving the joystivk down will move the zone’s bottom border further down.

4. Press the joystick again to reduce the zone’s size. The zone’s borders will appear red. a. Moving the joystick to the right will move the zone’s left border further to the right. b. Moving the joystivk to the left will move the zone’s right border further to the left. c. Moving the joystivk up will move the zone’s bottom border further up. e. Moving the joystivk down will move the zone’s top border further down.

5. To exit edit mode, press & hold the camera’s joystick controller for three (3) seconds.

EXIT_JUMP

Go to the Exit menu to save & exit, or exit without saving

right-hand corner of the screen when the camera detects motion.

PRIVACY (PRI)

PRIVACY MASK

You can hide some parts of the screen for privacy purposes. A total of 6 privacy masks are available. To enable Privacy Zone Masking, Select ON.

1. Select a mask (1~6) and enable by selecting ON

2. Enter edit mode for a desired mask. The edit mode will display all masks that have been turnied ON. The mask you selected will appear in WHITE. All other enabled masks will appear in GREEN.

3. When the mask in WHITE, use the joystick to move the mask to the area you wish to hide.

4. Press the joystick. The mask’s color will change to BLUE. Use this option to adjust the mask’s size.

5. Move the joystick Left and Right to adjust the width of the mask.

6. Move the joystick Up and Down to adjust the height of the mask. NOTE: when adjusting the size of the mask, the top and left borders of the mask will remain stationary. Only the right and bottom borders of the mask will move to adjust the mask’s size.

7. If you have enabled multiple masks, press the joystick again to remain in edit mode and move to the next mask chronologically.If you are in size edit mode (BLUE mask) and you press the joystick once, the next mask will turn WHITE, and the previous mask would turn GREEN.

8. To exit edit mode, press & hold the joystick for three (3) seconds.

MASK COLOR

Adjust the color of the privacy masks. Select from: WHITE / BLACK / RED

EXIT_JUMP

Go to the Exit menu to save & exit, or exit without saving

SYNC (SYC)

INT1 INT2

Select INTERNAL if camera uses DC power, or if L/L is not required. Please note this setup option is only for NTSC version.

**Consult your installer for additional information and assistance with configuration.**

INT1: SYNC to 59.94Hz INT2: SYNC to 60.01Hz In PAL, INT1 & INT2 SYNC to 50.00Hz.

LL (Line Lock)

Select L/L to syncronize video signals when two or more cameras are using AC power in a switching system.

EXIT_JUMP

SAVE & EXIT EXIT

Exit the OSD after saving the current settings. Exit the OSD without saving.

SET-UP (SET)

PC CONTROL

- CAMERA ID (1~255) You can assign ID number for the camera (1 by Default).

- PROTOCOL (PELCO-D by Default)

- BAUD RATE (2400 / 4800 / 9600 / 19200) Adjust data communication speed. Default is 9600.

TITLE

Select if you want to display the camera’s title on screen. You can setup a title up to 8 characters long. To edit the camera’s title, move the joystick to the right. The 1st letter will be highlighted. Move the joystick left and right to select the desired character. Press the joystick to move to the next space and repeat as necessary.

ID POSITION- Select the position for the camera’s Title:

-Up-Left

-Up-Center

-Up-Right

-Down-Left

-Down-Center

-Down-Right

LANGUAGE

You can select langaue you want to dispay on the monitor.

ENGLISH / DEUTSCH / FRANCAIS / ITALIAN / ESPANOL / DUTCH

SET-UP (SET)

OMNI LENS**

You can set OMNI LENS menus when you use Omni Focus Lens.

When OMNI LENS is set ON , you can set the folloing sub-menus.

- ALARM works with MOTION DETECT fuction. When motion is deteced, camera gives an alaram. Select ON or OFF.

- READ TIME is to set how many seconds to stay in zoom in. Select from 5 to 15 seconds.

- ALARM ZOOM is to set zoom rate when alarm occurs. Select from 4 to 214.

- STAND BY is the zoom rate when it’s normal scene. Therefore, when alarm disappear the zoom rate comes back to STAND BY rate. Select from 0 to 214.

FLUORESCENT

CRR (Color Rolling Reduction)

**Only for NTSC version**

DIGITAL VIDEO OUTPUT

- CRR1 If you use a manual lens, select CRR1 to release Rolling/Flicker problem.

- CRR2 If you use a DC lens, select CRR1 to release Rolling/Flicker problem.

- DIGITAL OUTPUT (OFF / ON)

- FIELD ORDER (NORMAL / REVERS)

- FRAME RPT (OFF/ 2X / FREEZE)

EXIT_JUMP

SAVE & EXIT EXIT

**Omni-Lens Settings available only in cameras with Moni Lens.**

Exit the OSD after saving the current settings. Exit the OSD without saving.

EXIT (EXT)

EXIT

Exit the OSD without saving.

SAVE & EXIT

Exit the OSD after saving the current settings.

FACTORY SET

Go back to factory default.

TROUBLESHOOTING

Before sending your camera for repair, check the following or contact our technical specialist.

FOR NO VIDEO

Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the camera’s OSD menu. Check the power supply and make sure the camera has the proper voltage and current.

FOR OUT-OF-FOCUS VIDEO

Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment. The use of a field test monitor is recommended.

WARRANTY INFORMATION*

Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows:

LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge.

PARTS: In addition, the Warrantor will supply replacement parts for the initial five (5) years and one (1) year on IR LED.

To obtain warranty or out of warranty service, please contact a Technical Support Representative at 1-866-446-3595 Monday through Friday from 8:30AM to 8:00PM Eastern Standard Time.

A purchase receipt or other proof of the original purchase date is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.

LIMITS AND EXCLUSIONS*

There are no express warranties except as listed. The warrantor will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitatons on how long an implied warranty lasts, so the exclusions or limitations listed above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state.

If the problem is not handled to your satisfaction, then write to the following address:

Digital Watchdog, Inc. ATTN: RMA Department 5436 W. Crenshaw Street Tampa, FL 33634

Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser.

SPECIFICATIONS*

VIDEO

Image Sensor 1/3" PIXIM Nightwolf CMOS Sensor Total Pixels 768 (H) x 548 (V) Scanning System 525 Lines, 2 : 1 Interlace Frequency 15.734KHz (H), 59.95Hz (V) Synchronization Internal / Line Lock Horizontal Resolution 690 Effective Horizontal TV Lines Minimum Illumination F1.2 (30IRE): 0.22Lux [Color] F1.2 (30IRE): 0.01 Lux [B&W] S/N Ratio 50dB (AGC off) Video Output CVBS: 1.0Vp-p / 75 Ω

LENS

Focal Length 3.3-12mm Lens Type DC Auto Iris

OPERATIONAL

Lens MANUAL / DC AE Preference OUTDOOR / INDOOR Back Light Compensation OFF/ ON Wide Dynamic Range LOW / NORMAL / MEDIUM / HIGH / CUSTOM Auto Gain Control LOW / MEDIUM / HIGH Star-Light OFF, x2-30FPS ~ x64

SPECIFICATIONS*

OPERATIONAL

White Balance Mode ATW/ PUSHLOKC / MANUAL / AWC/ NORMAL Day & Night AUTO / COLOR / B&W Mirror OFF / MIRROR / V-FLIP / ROTATE Sharpness -8 ~ 8 3D Digital Noise Reduction OFF/ LOW/ MEDIUM/ HIGH Digital Zoom x1 ~ x8 Privacy Zones OFF / ON (6 Programmable Zones) Baudrate 2400 ~ 38500 Protocol PELCO-D Language ENGLISH, DEUTSCH, FRANCIAS, ITALIAN, ESPAÑOL, DUTCH

ENVIRONMENTAL

Operating Temperature -29oC ~ 55oC (-20oF ~ 131oF)

Operating Humidity Less than 90% (Non-Condensing)

Storage Temperature -29oC ~ 70oC (-20oF ~ 158oF)

IP Rating IP68

ELECTRICAL

Power Requirement Dual (12VDC & 24VAC)

Power Consumption 12VDC: 2.1W, 175mA

24VAC: 2.2W, 91.7mA

MECHANICAL

Housing Material Aluminum

Dome Cover Material Polycarbonate

Dimensions

Weight 2.028 lbs

(Protects against dust and immersion beyond 3ft.)

∅

139 X 118.8 mm (∅5.47 X 4.7 in)

MEMO*

5436 W Crenshaw St. Tampa, FL 33634

Tel : 866-446-3595 / 813-888-9555

Fax : 813-888-9262

www.Digital-Watchdog.com

technicalsupport@dwcc.tv

Technical Support Hours : Monday-Friday

8:30am to 8:00pm EST

Digital Watchdog DWC-V4365T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual