Digital Watchdog DWC-PZ21M69T Quick Start Guide

DWC-PZ21M69T

Quick Manual &
Download Guide

Quick Manual &
Download Guide

Screw &

Plasc Anchor-4pcs

Quick Manual &
Download Guide

Screw &

Plasc Anchor-4pcs

Torx Wrench

Quick Start Guide

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. Mounting surface must withstand three times the weight of the camera.

2. Do not let the cables get caught in improper places or the electric line cover to be damaged. This may cause a short or fire.

3. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.

4. For the installation process, remove the dome cover by loosening the screws on the dome. Use the wrench provided with the camera.

STEP 2 – POWERING THE CAMERA

Connect the camera to the PoE injector included in the box. Connect the PoE injector to an adequate power source. See table

below for power source requirements. Refer to the user manual for more options to power up the camera.

Quick Start Guide

Template Sheet

Username: admin Password: admin

WHAT’S IN THE BOX

Quick Manual &
Download Guide

Template Sheet 1 Set Tor x Wre nch 1 Set

Moist ure absorber ­2pcs & Absorber Gui de

PoE Injector and
power cable

Tel: [phone]

Atten tion: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper camera usage.

1 Set

1 Set

1 Set

Screw & Plastic
Anchor – 4pcs

Waterproof cap
& Gasket

Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday

1 Set

1 Set

digital-watchdog.com

Power Requirements Power Consumption

DC12V, PoE IEEE 802.3at PoE+ class 4
(High power PoE injector included)

NOTE: Wh en using the PoE+ injector, do not connect th e PoE inje ctor to the

PoE/PoE+ switch or PoE/PoE+ enabled port of PoE/PoE+ switch.

DC12V Max 21.5W
PoE Max 23.4W

power cable,
connected to
adequate
power source.

PoE
Injector

Ethernet
cable

Ethernet Switch

STEP 3 – INSTALLING THE CAMERA

1. To use the camera’s water proof wiring:

(1)

. Install the LAN cable into (a).

(2)

. (b) will be assembled to (a) with a 1/4 turn.

(3)

. Thread (c) tightly to (b).

NOTE: Wh en using the water proof ca p, crimp th e RJ45 connector after

passing the cable through the waterproof cap.

a

b

2. Your camera comes with a moisture absorber included in the package. This

absorber needs to be installed inside the camera, next to the lens, to prevent

moisture build-up on the camera’s dome that reduces image quality.

(1)

. Remove the moisture absorber from the packaging.

(2)

. Follow the diagram to place the absorber in the appropriate location.

3. The camera’s four individual sensors can be rotated and tilted to adjust the camera’s views. Max tilt and rotation:

- Rotation: 20º

- Tilt: 18º

4 . Assemble the dome cover over the camera body and detach the protecting film to complete the installation.

c

Reset Buon

To reset the camera, press the reset button. Pressing the button for five (5) seconds will initiate a
camera-wide reset of all the settings, including network settings.

Quick Start Guide

STEP 4 – DW IP FINDER™

Use the DW IP Finder™ software to scan the network and detect all MEGApix® cameras, set the camera’s
network settings or access the camera’s web client.

Network Setup

1. To install the DW IP Finder™, go to: http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page and press Enter.

3. Click on the DW IP Finder from the search result and go to Software tab. Click on download icon

to download the DW IP Finder installation le.

4. Run the installation le and follow the wizard to install the DW IP Finder™. Open the

DW IP Finder™ and click ‘Scan Devices’. It will scan the selected network for all supported devices
and list the results in the table. During the scan, the DW logo will turn gray.

Select DHCP if the internet service is dynamic IP. This will allow the camera to receive its IP address from
the DHCP server.

Select Static to manually enter the camera’s IP address, (Sub)Netmask, Gateway and DNS information.
* The camera’s IP must be set to Static if connecting to DW Spectrum

Contact your network administrator for more information.

Default TCP/IP information: DHCP

5. Select a camera from the list by double-clicking on the

ca mer a’s image or clicking on the ‘Click’ button under the
IP Conf. column. The pop-up window will show the camera’s
current network settings, allowing admin users to adjust the
settings as needed.

6. To access the camera’s webpage, click on ‘View Camera

Website’.

7. To save the changes made to the camera’s setting, input

Username and Password of the camera and click Apply. Click
Scan Devices from the main screen again to display the
updated information.

‘Port Forwarding’ has to be set in your network’s router
for exter nal access to the camera.

Default ID / PW : admin / admin

NOTE: For security pur poses, it is highly recommended to

change your pas sword af ter initial setu p.

Thumbnail view

Select network to scan

Filter device type to scan

Scan devices

Show/hide thumbnail view

Refresh thumbnail view

Bulk IP assignment

Firmware upgrade

Firmware version

Camera’s uptime

Open Device

conguration

settings

Device’s
information

STEP 5 – WEB VIEWER

Once the camera’s network settings have been setup properly, you can access the camera’s web viewer.
To open the camera’s web viewer:

1. Find the camera using the DW IP

Finder.

2. Double-click on the camera’s view in

the results table.

3. Press the ‘View Camera Website.’

The camera’s web viewer will open
up in your default web browser.
Make sure you are using Internet
Explorer to view video from the
camera.

4. Enter the camera’s username and password (default are admin / admin).

5. If you are accessing the camera for the rst time, install the VLC les to view video from the camera.

6. To adjust the camera’s sensors alignment, go to the camera’s settings, under Alignment conguration.

See the camera’s user manual for all setup options and congurations.

1 2

NOTE: Please se e the full manual for additional i nstallation options, connecting exte rnal devices, web viewer setup,

camera settings and more.

Rev Date : 11/18 Copyright © Digit al Watchdog. All ri ghts reserved. S pecifications and pricin g are subje ct to chang e withou t notice.