Page 1
User’s Manual
Ver. 03/18
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
MEGApix® PANO
TM
9MP
180°, 360° fisheye view camera
DWC-PVF9M2TIR
Page 2
Safety Information
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.
Warning Precaution
This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
:
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
To prevent damage which may result in fire or electric shoc
hazard, do not expose this appliance to rain or moisture.
WARNING
Be sure to use only the standard adapter that is specified i
the specification sheet. Using any other adapter could caus
fire, electrical shock, or damage to the product
Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to th
product.
Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation
or fire
Securely plug the power cord into the power receptacle.
Insecure connection may cause fire
When installing the camera, fasten it securely and firmly
A falling camera may cause personal injury.
Do not place conductive objects (e.g. screw drivers, coins,
metal items, etc.) or containers filled with water on top o
the camera. Doing so may cause personal injury due to fire
electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock
If any unusual smells or smoke come from the unit, stop
using the product. Immediately disconnect the power sorce
and contact the service center. Continued use in such a
condition may cause fire or electric shock
If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.
When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock
WARNING
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Precaution
Operating
• Before using, make sure power supply and all other parts are
properly connected.
• While operating, if any abnormal condition or malfunction
is observed, stop using the camera immediately and contact
your dealer.
Handling
• Do not disassemble or tamper with parts inside the camera.
• Do not drop the camera or subject it to shock or vibration as
this can damage the camera.
• Clean the clear dome cover with extra care. Scratches and
dust can ruin the quality of the camera image.
Installation and Storage
• Do not install the camera in areas of extreme temperature,
exceeding the allowed range.
• Avoid installing in humid or dusty environments.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic
ÿelds and electric signals.
• Avoid installing in places where the camera would be subject
to strong vibrations.
• Never expose the camera to rain or water.
Page 3
Important Safety Instructions
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste stream
stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interferenece at his own expense.
1. Read these instructions. - All safety and operating instructions should be read before installation or operation.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; near a swimming pool; etc.
6. Clean only with dry cloth. - Unplug this
product from the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surfaces. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s instructions have been adhere to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug the apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Page 4
Table of Contents
Introduction
Product & Accessories......................................................................................................................................................................5
Parts Name...........................................................................................................................................................................................6
Installation
Factory Reset......................................................................................................................................................................................7
Installation.....................................................................................................................................................................................8-11
Cabling...............................................................................................................................................................................................12
SD Memory Card.............................................................................................................................................................................14
Network Setup
DW IP Finder.....................................................................................................................................................................................15
Web Viewer
Login to the camera.......................................................................................................................................................................16
GUI Overview.............................................................................................................................................................................17-18
Camera Settings
Settings>status...............................................................................................................................................................................19
Settings>network..........................................................................................................................................................................20
Settings>video source.................................................................................................................................................................21
Settings>camera setup.........................................................................................................................................................22-23
Settings>motion detection.......................................................................................................................................................24
Settings>ROI encoding...............................................................................................................................................................25
Settings>OSD.................................................................................................................................................................................26
Settings>privacy mask................................................................................................................................................................27
Settings>video profile..........................................................................................................................................................28-29
Settings>audio profile................................................................................................................................................................30
Settings>streaming settings..............................................................................................................................................31-32
Settings>events............................................................................................................................................................................33
Settings>local storage................................................................................................................................................................34
Settings>services>date and time...........................................................................................................................................35
Settings>services>UPnP............................................................................................................................................................36
Settings>services>bonjour.......................................................................................................................................................37
Settings>services>SNMP...........................................................................................................................................................38
Settings>services>port..............................................................................................................................................................39
Settings>services>security.......................................................................................................................................................40
Settings>services>DDNS...........................................................................................................................................................41
Settings>account.........................................................................................................................................................................42
Settings>maintenance>firmware update..........................................................................................................................43
Settings>maintenance>factory default..............................................................................................................................44
Settings>maintenance>report...............................................................................................................................................45
Settings>maintenance>open source info..........................................................................................................................46
Settings>reboot............................................................................................................................................................................47
Appendix.............................................................................................................................................48-49
FAQs..........................................................................................................................................................50
Dimensions...............................................................................................................................................51
Warranty...................................................................................................................................................52
Limits & Exclusions...................................................................................................................................53
Disassembling the Camera............................................................................................................................................................7
Page 5
Product & Accessories
Introducon -
Screw &
Plasc Anchor-3pcs
Camera
Cable
Template Sheet
for Installing by Bolt & Nut
Mount Plate
Template Sheet
for Installing by Plate
Mount Bolt & Nut
Torx Wrench
Waterproof cap & Gasket
Quick Manual &
Download Guide
5
Page 6
Part Name
Introducon -
Mount Plate
Plate Hook
Dome Cover
Fisheye lens
Window cover
Reset buon
SD Card Slot
Illuminaon Sensor Hall
Illuminaon Sensor
Waterproof cap
DC Power Jack
RJ-45 Connector
Alarm In/Out
Audio In/Out
6
Page 7
Disassemble the camera
Installaon -
Reset to the Factory Default
Press the reset buon for 5 seconds to return the setup
to the factory default.
If you press the ‘Reset’ buon, you will lose all seng
data. If needed, please, make a note for further installaon.
Warning:
Before installing your camera, you have to read the following cauons.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
1. You have to check whether the locaon can bear five mes of the weight of your camera.
3. When installing your camera, don’t allow any person to approach the installaon site. If you have any
valuable things under the place, move them away.
Detach the dome cover by torx wrench provided from
boom case before installaon the camera.
1. The camera includes a sensor at the camera’s module.
For the sensor to funcon properly, the camera’s dome
includes a special hole the sensor.
2. When assembling the camera together, please make
sure the sensor hole in the camera’s dome is posioned
right on top of the sensor on the camera’s module.
1
UPPER-SENSOR HOLE POINT
BOTTOM- CABLE HOLE
GASKET-CABLE HOLE POINT
7
Page 8
Installaon
Installaon -
Template Sheet
1
2
3
Detach the camera’s cover dome from the camera’s
module by unscrewing the three cover dome screws
using the L-wrench.
Use the camera or mounng template to mark and
drill the necessary holes in the wall or ceiling.
Pull wires through and make connecons.
4
Using two (2) included screws, mount and secure the
camera to the mounng surface.
Secure the camera’s cover dome onto the camera
base to complete the installaon.
5
Detach the protecon film from the dome cover.
6
Put the Lan cable into (a), then (b) will be assembled to (a)
without making any space.
ghtly. As a final step, (c) need to be assembled to (b)
a
b
c
8
Page 9
Installaon Using Mount Plate
Installaon -
Template Sheet
1
2
Detach the camera’s cover dome from the camera’s
module by unscrewing the three cover dome screws.
Using the metal mount plate, mark and drill the necess
-ary holes in the wall or ceiling.
Pull wires through and make connecons.
Using the three (3) included screws, mount and secure
the camera to the wall or ceiling.
3
4
Aach the camera base to the metal mount by snapp
-ing it into place using the two metal handles.
Secure the camera’s cover dome onto the camera base
to complete the installaon.
5
6
Detach the protecon film from the dome cover.
7
9
Page 10
Installaon -
Installaon Using Mount Bolt & Nut
Using the template sheet, make and drill the cabling
holes on the wall/ceiling.
Secure the two long mounng screws to the camera’s
base.
Pass the wires through the mount bracket and make
all necessary connecons.
1
3
2
10
Page 11
Installaon -
Installaon Using Mount Bolt & Nut
5
Mount the camera to the mounng surface by using
the 2 mounng nuts. Rotate the locking discs over the
screws unl the camera is held ghtly from the mount
-ing surface.
Secure the camera’s cover dome onto the camera base
to complete the installaon.
6
Detach the protecon film from the dome cover.
4
11
Page 12
Cabling
Installaon -
Power
Two Opons
Use a PoE-enabled swch to connect data and power through a single cable and begin viewing and recording images instantly.
A non-PoE switch will require an adaptor for power transmission.
Ethernet cableEthernet cable
2. Using a Non-PoE Switch
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing transmission of
power and data via a single Ethernet cable.
PoE eliminates the need for the different cables used to
power, record, or control the camera. Follow the illustraon
below to connect the camera to a PoE-enabled switch using
an Ethernet cable.
If a PoE-enabled switch is not used, use a power adaptor
for power transmission and non-PoE switch for data
transmission.
Follow the illustraons below to connect the camera
without a PoE-enabled Switch.
12
Page 13
Alarm Output
Alarm Input
Cabling
Installation -
Audio Output
Connect the ‘Audio Out’ cable of the camera to device like
speaker.
Audio Input
Connect the ‘Audio In’ cable of the camera to the device like
microphone.
Power Connecon
Please, check the voltage and current capacity of rated power
carefully.
Network Connecon
Connect the crossover cable into the RJ-45.
Rate
Power
Current
Consumption
DC 12V 7W
PoE
IEEE 802.3af
Class 3
Alarm Output
It connects to the alarm lights, siren or lamps, and it is
acvated according to the Setup menu seng.
Cable of the relay output device should connect to the line
of the Alarm Cable.
Alarm Input/Sensor
Cable of the sensor/alarm input device should connect to the
line of the Alarm Cable.
Audio Input
Audio Output
Power
Network
Alarm Output
Alarm Input
1
1
2
2
3
3
4
4
5
6
5
5
6
6
13
Page 14
Micro
Inserng/Removing an SD Memory Card
Installaon -
Inserng an SD Memory Card
Insert the SD card in the arrow direcon.
Don’t insert the SD memory card while it’s upside down by force.
Otherwise, it may damage the SD memory card.
Removing an SD Memory Card
Removing an SD Memory Card Gently press down on the
exposed end of the memory card as shown in the diagram
to eject the memory card from the slot.
Pressing too hard on the SD memory card can cause the card to
shoot out uncontrollably from the slot when released.
If you have saved data in the SD memory card, removing the SD
memory card prior to seng record to OFF will cause damage to
the data stored in the card.
The memory card is an external data storage device
that has been developed to offer an enrely new way
to record and share video, audio, and text data using
digital devices.
Recommended SD Card Specificaon (Not Included)
- Type: Micro SD (SDHC)
- Manufacturer: Transcend, Kingston, Toshiba, SanDisk
- Capacity: 4GB~32GB
- Class: UHS-I U3 Class 10
1
2
SD card slot
Reset button
SD card slot
Reset button
14
Page 15
Refresh Thumbnail View
Refresh Search Results
Camera’s IP Address
DHCP Status
Camera’s Name
Camera Firmware
Camera’s Thumbnail View
Live Time
Web Port
Camera’s Model Number Network’s Gateway
Camera’s Model Mac Address
Network’s Netmask
Camera
Firmware update
Network Setup -
DW IP Finder
TM
Show / Hide Thumbnail View
Go to : http://www.digital-watchdog.com and search for ‘IP
Finder’ on the quick search bar at the top of the page.
The latest IP Finder software will appear in the search results.
Click on the link to download the file to your computer.
The software will scan your network for all supported cameras
and display the results in the table. Allow up to 5 seconds for
the IP Installer to find the camera on the network.
You can press the ‘Refresh List’ to search the network again,
or filter the search results by entering a value in the filter box
at the bottom of the page.
Check the box next to ‘Display Camera Thumbnail’ to view a JPEG image of the camera’s view next to the camera name.
JPEG image of the camera's view next to the camera name
on supported models.
To save the changes made to the camera's settings, input ID
and PW of the camera for authentication.
If the camera needs to be rebooted after the settings were
changed, press the 'Reboot' button. The camera will power
cycle and will appear back in the search results once the
reboot is complete.
The camera's default network information is :
Click 'Save' to save changed values.
To update the camera's firmware from the DW IP FinderTM,
click on the firmware tab, upload the firmware file and select
the cameras to update. You can update multiple cameras at
the same time.
A ‘Port Forwarding’ has to be set in your network’s router for
external access to the camera.
Default TCP/IP information
- IP: 192.168.1.2
- Subnet Mask: 255.255.255.0
- Gateway: 192.168.1.1
- DNS : 168.126.63.1
Select DHCP if the internet service is dynamic IP. This will allow
the camera to receive its IP address from the DHCP server.
Select STATIC to manually enter the camera's IP address, subnet
mask, Gateway and DNS information.
Contact your network administrator for more information.
Default ID / PW : admin / admin
15
Page 16
Webviewer - Settings
Login
Administrator connection (on the initial page)
1) “ID” admin (Unchangeable)
2) “Password” admin. (the default password can be changed in the web setting page)
3) Type the ID and password and click the button “Login”, the web monitoring page shows up.
4) You can also type the ID and password and click “Login” after checking the box “Setting” to go directly to the camera’s settings
page.
Guest connection (on the initial page)
1)
“Guest Login” click the test “Guest Login” below the button “Login” without an ID and a password.
2)
Under the guest connection, only restrictive functions will be available. Settings page can not be accessed as a guest.
16
Page 17
Webviewer - Settings
Web viewer
Monitor and configure the MEGApix® camera through a built-in web viewer.
Type the camera’s IP address in a web browser. Enter Username and Password. Default: Username: admin | Password: admin
The web browser may ask to install ActiveX to view video from the camera. Once it has been installed, Internet Explorer will
display video images from the camera.
Internet Explorer version 8.0 or higher are recommended.
The Web Client is also available in Google Chrome, Safari and Firefox web viewers. Please note that features may be limited.
Snapshot: Capture a still image from the camera’s live view. The image is saved as a .jpeg file to your local downloads directory.
View the camera in full screen: you can hide all the settings and menu options and display the camera’s view across your entire
monitor. Press Esc to exit the full screen mode.
Local Recording: Record short videos from the camera’s streaming and save them locally.
1)
Click the Record button to start recording. A red frame will appear around the display area.
2)
Click the Record button a second time to stop recording.
3)
the recorded video will be saved locally to your directory.
17
Page 18
Webviewer - Settings
Web viewer
Monitor and configure the MEGApix® camera through a built-in web viewer.
Setting button - Enables you to move to the web setting page (Live button : Web setting page -> Web monitoring page)
Show Log button - The window for the log data shows up.
ActiveX Download button - Click this button if the ActiveX for video monitoring is not downloaded automatically.
Language menu - The language can be selected out of the items of the language box.
Display Size - Fit View Size check box: The adjustment bar shows up when this check box is unchecked.
Video & Stream - The selected one out of the streams displays on the page. For the activation of the streams, check the item
“Video Profile” on the web setting page.
Relay Out button - Controls the external device that is connected. (Before use, check the availability of the product features or
the connection status of the installed equipment.)
Digital Input - Shows the contact signal connected.
Audio On/Off - Enables you to monitor the audio signal of the microphone connected. (Audio IN connector)
(Before use, check the availability of the product features or the connection status of the installed equipment.)
Snapshot - Captures a JPEG Image of the current video stream (JPEG file path: C:/)
Record Start - Records the video of the current video stream (AVI file path:C:/), The red outline shows up on recording.
Info - Shows the information of the transferred data on the upper side of the image.
1)
Image information : FPS (frame/sec) / Camera (Channel) Name / Resolution
2)
Event Status- : Motion Detect (red) / Video signal (green) / Digital IN (blue)
3)
For the use of the motion detection, the check box “Enable” of the item “Motion Detect” should be checked.
About - Displays the ActiveX information.
18
Page 19
Webviewer - Settings
Status
View the camera’s basic settings and status.
Network Status - Displays the camera’s current network information, including MAC Address, IP Address, Subnet Mask, Gateway,
Default DNS, IPv4, Received Data velocity, Transmitted Data velocity, and the connection status for Link Speed/Duplex Mode.
Model Information - Displays the camera’s hardware information, including Firmware and Boot Loader versions, camera’s Model,
Serial Number, System Mode and local storage information.
Camera Time - Displays the camera’s time information including the camera’s current time settings and the running time
(how long the camera has been running since the last time it booted up).
CPU Temperature - Show the camera’s CPU running temperature, including proper range in °C.
19
Page 20
Webviewer - Settings
Network
View the camera’s network information.
IP Address
1) Dynamic IP - Select Dynamic IP if you are using a DHCP Server. The camera will obtain all its network information automatically
from the server.
2) If you do not have a DHCP server, or wish to manually enter the camera’s network information, select static IP Address from
the drop-down options. Contact you Internet Service Provider(ISP) or Network Administrator for more information.
Subnet Mask - The camera is set to DHCP. Subnet will change according to network settings.
Gateway - This is your router’s external IP address. This address is used when accessing the camera remotely from outside the
network. The router will channel the data request to the appropriate port associated with the camera.
Default DNS - Enter a Domain Name Server (DNS) address. This translates a web addresses to an IP addresses.
IPv4 Link Local Network Setting - Enabled by default.
1). IP Address, Subnet Mask
These are set automatically based on you settings in the Network Setting section.
IPv6 Network Setting - Disabled by default.
1) Manually set the camera’s IP address and gateway. The number next to “/” on IPv6 Address are setting value for the
sub-network.
2) IPv6 LinkLocal - Set automatically by the communication between the local network devices. This is disabled by default.
Link Speed / Duplex Mode - If the auto negotiation mode has a problem with the connected network device, use a specified value.
The value of the camera and the network device should be the same.
Status - The status of the current network connection.
Click OK to apply any changes to the settings.
20
Page 21
Webviewer - Settings
Video Source
Adjust the camera’s input source, add OSD text and adjust the camera’s image settings.
Camera Input Source
1) Mirror / Flip - Select to reverse or flip the camera’s image.
2) Click OK to apply any changes to the settings.
Camera Control (Display OSD Text) (not supported) : Shows the camera display.
Common
1) Brightness - The higher the number, the brighter the image will appear. Default value is 50.
2) Contrast - The higher the number, the contrast between the dark and bright areas in the camera’s FoV will be more distinct.
Default value is 50.
3) Saturation - The higher the number, the more vibrant the colors will appear on the camera’s image. The lower the number,
the more black and white the image will appear. Default value is 60.
4) Hue - The higher the number, the camera’s image will use warmer tones. The lower the number, the camera’s image will use
cooler tones. Default value is 50.
21
Page 22
Webviewer - Settings
Camera Setup
Monitor and configure the MEGApix® camera through a built-in web viewer.
General - This section allows you to adjust the camera’s lens, iris and day/night mode.
1) Lens - Sets the type of the Lens. Select from Fixed, Fisheye, Varifocal or MFZ. Please note that options may not be available
based on the camera’s model and lens.
2) Iris - Sets the type of the Iris (on supported cameras)
3) CDS>>Type - Sets the type of the CDS from internal or none. The CDS affects the day/night transition.
4) CDS>>Range>>Min & Max - Marks the light level at which the camera will switch between color and B/W. Set the minimum
and maximum values for the CDS threshold. Default values are mentioned next to the drop-down menu.
5) IR - You can manually activate the cameras IR LED board. Select Built-in to activate the IR LEDs in the camera when low light is
detected. If you are using an external light source, or the camera’s own IR LEDs interfere with other LEDs in the system, you
can set it to non, and manually disable it.
6) ICR - This allows you to set the camera’s day/night mode. You can select to keep the camera in color or B/W regardless of the
lighting conditions, or set to auto. If auto is set, the camera will switch between color and B/W according to the CDS settings
set above.
AE - This section allows you to adjust the camera’s Auto Exposure settings.
1) WDR>>Mode - Select D-WDR to enable WDR. The Wide Dynamic Range is used when there are extremely bright and extremely
dark areas in the VoF of the camera.
2) WDR>>Strength - Adjusts the strength of the WDR. The higher the value, the stronger the WDR treatment will appear on the
camera’s image.
3) Antiflicker>>Enable - Check the box to enable the Antiflicker function.
22
Page 23
Webviewer - Settings
Camera Setup
Monitor and configure the MEGApix® camera through a built-in web viewer.
Special - Use this section to adjust the camera’s De-Fog, Smart DNR(T), Sharpness.
1) Defog>>Enable - Select to enable the camera’s De-Fog feature. This allows the camera to process a scene that is obscured by fog
or weather conditions and provides a visibly improved image.
2) Defog>>Strength - Adjusts the strength of the defog. The higher the number, the stronger the De-Fog treatment will appear
on the camera’s image.
3) Noise Reduction>>Enable - (Smart 3D DNR™ Digital Noise Reduction) – Control the level of noise in the image. If enabled, the
camera will manipulate the image to reduce digital noise, but it may also increase lagging when motion occurs.
4) Sharpness>>Mode - Select Auto or Manual to activate the camera’s enhanced sharpness, or Disable.
5) Click OK to apply any changes to the settings.
AWB - This section allows you to adjust the camera’s Auto White Balance settings.
1) Red Gain - Adjusts the amount of red in the image.
2) Blue Gain - Adjusts the amount of blue in the image.
3) Speed - Set a duration for collecting data for Auto white balance. It is recommend to leave at the default value.
23
Page 24
Webviewer - Settings
Motion Detection
To setup a motion detection mask on the camera’s view, click on any point in the camera’s preview and drag to make a
detection range. once a motion detection mask is set, a red mark will appear on the upper bar of the video image on the web
monitoring page. The camera supports four (4) different motion detection masks. Each one can be setup individually be
selecting the appropriate tab (ROI#1~4 tab).
Fill All - If enabled, the entire camera’s FoV will be set to motion detection.
Clear All - Deselects the selected area.
Invert - Inverts the selected area.
Enable - Check the box for the activation.
Sensitivity - The higher the value, the more sensitive to motion the area will be.
Threshold - When the ratio of the moving parts to the whole image is on the range, the detection is checked.
Click OK to apply any changes to the settings.
24
Page 25
Webviewer - Settings
ROI Encoding
ROI (Region of Interest) Encoding function: the region specified by a ROI is encoded to transmit a relatively good
image compared to other regions.
To activate, check the Enable box.
The camera supports up to four (4) separate ROIs. Select out of "ROI#1~4". Once you check the box next to a specific ROI, a
colored mask will appear in the camera’s display. Click and drag the mask to adjust the position and size of the region.
Sensitivity - Set from 1~100. The higher the value, the higher the mask’s sensitivity. (If the video bit rate is set to less than the
recommended bit rate, the image quality of the ROI will be affected.)
Click OK to apply any changes to the settings.
Setting and example
Condition - 1920x1080 resolution encoding, 1.5Mbps network bandwidth.
Setting - Setting the ROI to 1/4 of the entire image and the sensitivity to a value out of 40~60.
Effect - The quality of the image set to the ROI is similar to the image that is transferred by the transfer rate “4Mbps”
(the default value of 1920x1080 resolution). You can also monitor the non-ROI part.
25
Page 26
Webviewer - Settings
OSD
Add OSD text or a logo to the camera’s view.
OSD : : Text
Date / Time / Camera Name Enable - check the box next to the information you want to show on the camera’s image.
If the Camera Name is enabled, enter an appropriate name for the camera.
X Axis - Adjust the X axis position of the OSD text.
Y Axis - Adjust the Y axis position of the OSD text.
Font Size - Adjust the size of the OSD text.
Background Color - Select a color for the text’s background.
Foreground Color - Select a color for the text’s font.
OSD : : Logo
Enable - Check for the activation.
X Axis - Adjust the X axis position of the OSD Logo.
Y Axis - Adjust the Y axis position of the OSD Logo.
Click OK to apply any changes to the settings.
Before using the OSD Logo feature, refer to the firmware update / OSD Logo Update entries and upload a logo file.
26
Page 27
Webviewer - Settings
Privacy Mask
Index - Select the index 1 ~ 8 and Set the privacy index.
Active - The Privacy mask function can be enable or disable.
Color - Set the privacy mask’s color.
Black/Gray/White/Red/Green/Blue/Cyan/Yellow/Magenta.
27
Page 28
Webviewer - Settings
Video Profile
Adjust the camera’s streams, resolution, bit rate etc.
Streams -Select which stream to show in the preview and adjust in the settings of this page. The camera supports two
simultaneous stream plus a JPEG stream.
Proprietary Stream Port - The port number for transferring the video and audio data.
Compression - Select the compression type for the stream (H.265 / H.264 / MJPEG).
Resolution - Set the image size. The camera supports up to 9MP resolution.
Bitrate Type
1) CBR : the unit is kbps.
Bitrate Recommendation : 3000x3000 -> 8000 / 2048x1536 -> 6000 / 1080p -> 4000~6000 / 720p -> 2000~3000 /D1 -> 1000~1500
/ CIF -> 500~750)
2) VBR : 1(best) ~ 6
Frame Per Sec - The number of frames transferred in a second (default: 30)
Group Size - This sets the number of I-frames and P-frames per second. If GOP is set to 30, the camera will record 1 I-frame and
29 P-frames. To improve the recording quality, lower the GOP number. However, the lower the number, the larger the streaming
file size will be. (default: 60)
28
Page 29
Webviewer - Settings
Video Profile
Set the Expert Video Setting and JPEG Capture.
H.264 Reference Frames (Skipping Modes) - Once the value is set to "4X", the camera will play recorded video at "4X" with less
system resources.
Capture Mode -In case the resolution of the monitor is SD (Standard Definition), the HD (High Definition) video ratio (16:9) will
be changed to the SD video ratio (4:3).
1)
Squeeze : stretches the video horizontally to make the ration 4:3
2)
Crop : crops the video by the left and right end (the video ratio is kept).
Entropy Profile - Set the video’s encoding to decoding settings. Baseline is set as the default profile.
Compression ratio, system load: baseline < main < high. The bandwidth of "high profile" is less by 20% than that of "baseline".
Entropy Coding - The camera runs as CAVLC. (compression ratio: CAVLC < CABAC, system load: CAVLC < CABAC)
Jumbo Frame - Discards or processes the I-frames or P-frames in excess of a specific value.
(I Thr.: I frame threshold, P Thr.: P frame threshold).
Enable - Capture the camera’s view as JPEG.
Resolution - Adjust the resolution.
Quality -Set 1(Best) ~ 6.
Click OK to apply any changes to the settings.
29
Page 30
Webviewer - Settings
Audio Profile
Audio Option : : Input
Input Type - Line ( or line / mic ; the models with built-in mic)
Audio Codec - G.711-u / G.711-a / G.726 (quality : G.711>G.726, playing compatibility : G.711<G.726)
Sampling Rate - 8kHz (or 8kHz ; fixed on MR904)
Volume - 1 ~ 100
Audio Option : : Output
Audio Codec - G.711-u / G.711-a / G.726 (quality : G.711>G.726, playing compatibility : G.711<G.726)
Sampling Rate - 8kHz (or 8kHz ; fixed on MR904)
Volume - 1 ~ 100
Click OK to apply any changes to the settings.
30
Page 31
Webviewer - Settings
Streaming Setting
Adjust the camera’s streams and their advanced settings such as RTSP, TCP and Multi-cast.
Proprietary TCP Port - The port for the transmission by the proprietary protocol
(based on the settings under “Video Profile / Video Setting / Proprietary Stream Port ”).
Connection Lists - The IP address and port information of the monitoring devices that are connected to the camera.
RTSP Port - The port number used for RTSP transmission.
RTSP URI (Uniform Resource Identifier) - This is the path that is used on the monitoring program for playing RTSP stream from
the camera. The default paths are:
1) 1st Stream > rtsp://192.168.1.2:554/AVStream1_1
2) 2nd Stream > rtsp://192.168.1.2:554/AVStream1_2
3) 3rdStream > rtsp://192.168.1.2:554/AVStream1_3
Connection Lists - The IP address and port information of the monitoring devices that are connected to the camera.
31
Page 32
Webviewer - Settings
Streaming Setting
Adjust the camera’s streams and their advanced settings such as RTSP, TCP and Multi-cast.
Video Address - The IP address for video data transmission.
Video Port - The port number for video data transmission.
Video TTL - Set the number of the routers that pass when transmitting the video data.
Audio Address - The IP address for audio data transmission.
Audio Port - The port number for audio data transmission.
Audio TTL - Set the number of the routers that pass when transmitting the audio data.
User RTSP Authentication - Check the box if an authentication process is required.
Use RTCP - Check the box if RTCP function is required.
Use RTP/RTCP Keep-Alive - Check the box if the stream times-out.
Use Onvif Discovery - Check the box if Onvif Discovery is required.
Use Onvif WS-Security - Check the box if Onvif WS-Security is required.
The other protocols - Displays the supported protocols.
Click OK to apply any changes to the settings.
32
Page 33
Webviewer - Settings
Events
Digital Input
Logical Status (Sensor Type) - Set according to the normal state of the electrical signal of the attached device. (Open / Close)
1) N.O. (Normal Open) : in case of the normal state is “open”
2) N.C. (Normal Close) : in case of the normal state is “close”
Click OK to apply any changes to the settings.
Event Types
Add Event (+) button - Click this button to add an event entry.
Create New Event
1)
Event Type : Select one out of “Digital Input / Motion / Timer”
1-1) Digital Input > Sensor : Select a sensor to use. Digital Input > Status : Select one out of “close to open / open to close”.
1-2) Motion > ROIs : Motion ROI (refer to the item “Motion Detect”)
1-3) Motion > Status : Select one out of “On/Off”.
1-4) Timer > Interval : Select one out of “1~86400”
2)
Action Type : Select one out of “Preset Move / Digital Output / TDN”
2-1) Preset Move > No : Select one out of “1~255”. Set the preset on the item “Video Source”.
2-2) Digital Output > Relay/No : Select considering the connection “Digital Output”.
2-3) Digital Output > Status : Select one out of “close to open / open to close”.
2-4) Digital Output > dwtime : Duration (1~60 seconds)
2-5) TDN > Status : Select one out of “BW / Color” (not supported)
Delete event (-) button - Click this button to remove the event entry.
OK button - Click this button to apply the changed setting values.
33
Page 34
Webviewer - Settings
Local Storage
The camera supports SD/SDHC memory card for local recording.
Overwrite - Select whether to overwrite old data when the card is full.
Select Storage - This section shows the SD Card used for storage.
SD Volume - Shows memory information
1) File System : FAT32
2) Total : 14.83 GBytes
3) Used : 14.33 GBytes (96.65%)
4) Free : 508 MBytes (3.35%)
Storage Estimation - Shows the estimated time that can be saved.
Mode - Select off (not saving) / continuous (continuous recording) / event (records when an event occurs)
Event types that can be selected
1)
Motion : When motion occurs using the motion detection values in the ROI setup page.
2)
Sensor : When a sensor is activated using the camera’s Digital Input Settings.
3)
Network Link Fail (Unplugged) : When the camera’s network connection with the monitoring PC is lost.
4)
I-Frame Only (I-Frame shows at every 60 frames, 2sec.) : the camera will record only the main frames of the video.
The contents of the black “(...)” are the values that are set on the “Video Profile” settings.
Select Stream - Select which stream to record.
Click OK to apply any changes to the settings.
Model name Date/Time - Shows the camera’s time information.
Browser Date/Time - Shows the time information of the monitoring PC.
NTP Server - Enable the local storage to sync with the time synchronization settings.
Date Time Format - Select Camera(NVT) Local Time /UTC
34
Page 35
Webviewer - Settings
Services - Date/Time
Use this menu to adjust the camera’s local date, time, and time server settings.
Date/Time - Displays the current time.
New Date/Time (Manual) - Adjust the camera’s time manually. Click the “Set” button to apply the changes.
New Date/Time (Auto) - Synchronize the time with the time of the monitoring PC. Click the “Set” button to apply the changes.
Specify OSD Date/Time Format - Set the date and time format. Click the “Set” button to apply the changes.
Daylight Saving Enable (DST) - Check the box to enable the DST function..
Time Zone - Select the time zone from the available options.
Click OK to apply any changes to the settings.
Enable - Check the box to enable.
Interval - Set the request time intervals (in minutes).
Time Server - Enter the IP address or hostname of a time server.
Click OK to apply any changes to the settings.
Time Server : If enabled, the camera will synchronize its date and time with a time server.
35
Page 36
Webviewer - Settings
Services - UPnP
The camera supports UPnP for auto detection with Windows explorer.
Enable - Check to enable UPnP.
Friendly name - This is the name identifying the camera when using the UPnP search It is created by the camera’s MAC address.
You can modify it as needed.
Click OK to apply any changes to the settings.
36
Page 37
Webviewer - Settings
Services - Bonjour
The camera supports Bonjour for auto detection with Windows explorer.
Enable - Check the box for the activation.
Friendly name - It is created by the MAC address automatically. This can be changed after the check box “Enable” is checked.
Click OK to apply any changes to the settings.
37
Page 38
Webviewer - Settings
Services - SNMP
Use this menu to set the camera’s SNMP settings.
Enable - Check to enable.
Read community - Shows the running mode as “public”. (fixed)
UDP Port - Enter the port number for use.
Click OK to apply any changes to the settings.
38
Page 39
Webviewer - Settings
Services - Port
Use this menu to Set up the port number for the data communication.
Web (HTTP) - The camera’s web port is set by default to 80. You can modify it as needed.
Serial Port #1(RS485) (Currently not supported)
Serial Port #2(RS232) (Currently not supported)
Click OK to apply any changes to the settings.
39
Page 40
Webviewer - Settings
Services - Security
This menu allows you to restrict access to the camera according to IP addresses.
Enable - Check to enable.
Basic Policy - Select “allow” / “deny”
IP Addresses List - Create the IP address list for filtering. Press the ‘Add’ button to add new IP addresses to the list, or ‘delete’ to
remove them from the list.
My IP Address - Displays the IP address of the PC currently connected to the camera.
Click OK to apply any changes to the settings.
40
Page 41
Webviewer - Settings
Services - DDNS
The camera supports a Dynamic DNS feature. Please note that these are third-part DDNS services, and some may require
subscription or payment.
Enable - Check to enable.
Select Service - Select a service to use.
Type the information that is used on the registration process of the DDNS server homepage.
Click OK to apply any changes to the settings.
41
Page 42
Webviewer - Settings
Account
The camera supports multiple users with different permission levels.
Add User
1) Admin (Root) Password - Enter the administrator’s password.
2) ID - Enter or modify the ID for the user.
3) New Password, Confirm Password - Enter or modify the password for the ID to be added.
4) Apply/Cancel button - Click “Apply” to save the changes or “Cancel” to cancel.
Guest Login Enable check box - Check this box to enable guest login services. Click “Set” to apply the changes.
Max Number of Clients - The maximum allowed connections are 20. (fixed)
To add a new user, press the “Add User” button. To modify an existing user, press the “Modify” button next to that user’s name.
The Modify & Create New user page will appear.
42
Page 43
Webviewer - Settings
Maintenance - Firmware Update
Use this menu to update the camera’s firmware when needed.
Current Firmware Version - Displays the current firmware version.
Firmware File
1) Click “Browse...” and select the file to upload.
2) Click “Upload” to start updating.
The camera's power supply must not be interrupted. Updates can take up to 10 minutes.
Network setting will remain the same, however, video settings may be reset during the update.
Logo Upload
1) Click “Browse...” and select the file to upload.
2) Click “Upload” to start updating.
OSD Logo Upload
1) Click “Browse...” and select the file to upload.
2) Click “Upload” to start updating.
PTZ Protocol Update (not supported)
If anew protocol is uploaded, select the new protocol in the Video Source settings page and apply it by clicking "Set".
43
Page 44
Webviewer - Settings
Maintenance - Factory Default
When necessary, you can reset the camera to its factory default settings.
Reset button - Click the button to initialize the reset of the selected values. Please note to click the reset button only after
selecting the values to be initialized.
Show only changed values check box - Check to display only the changed values (default).
Select All check box - You can manually check the box next to each settings you want to reset, or use the Select All button to
selects all groups to be initialized.
44
Page 45
Webviewer - Settings
Maintenance - Report
This page displays the camera’s current setting and can be printed or saved as a PDF file for reference.
Use the “Print” button to export the report for you records.
45
Page 46
Webviewer - Settings
Maintenance - Open Source Info.
This page documents the camera’s firmware and web client information for open source integrations.
46
Page 47
Webviewer - Settings
Reboot
You can select to reboot the camera as needed. A confirmation window will appear to confirm the reboot.
47
Page 48
Appendix
A : Current TCP / IP Settings
1. Windows 7 Users 2. Windows 10 Users
Under the ‘General’ tab of the
TCP/IP Properties you will see
your IP address information.
Under the ‘General’ tab of the
TCP/IP Properties you will see
your IP address information.
If your IP settings are obtained automatically, you could use the MS-DOS prompt (or Command Prompt) to determine your IP address.
For information on how to do this, please read the FAQ.
Start
Start
Control Panel
Network and
sharing center
Manage network
connections
Select either
Internet Protocol
Ver.4 (TCP/IPv4)
or Internet Protocol
Ver.6 (TCP/IPv6)
Click Properties
Properties
Select either
Internet Protocol
Ver.4 (TCP/IPv4)
or Internet Protocol
Ver.6 (TCP/IPv6)
Click on Change
adapter options in
Ethernet
Settings
Network & Internet
Click Properties
Select the Ethernet,
Right click and
choose Properties
48
Page 49
Appendix -
B : Changing IP address and subnet mask
1. Windows 7 Users 2. Windows 10 Users
Select ‘Use the following IP
address’
Select ‘Use the following IP
address’
Start
Start
Control Panel
Network and
sharing center
Manage network
connections
Select either
Internet Protocol
Ver.4 (TCP/IPv4)
or Internet Protocol
Ver.6 (TCP/IPv6)
Click Properties
Properties
Select either
Internet Protocol
Ver.4 (TCP/IPv4)
or Internet Protocol
Ver.6 (TCP/IPv6)
Click on Change
adapter options in
Ethernet
Settings
Network & Internet
Click Properties
Select the Ethernet,
Right click and
choose Properties
49
Page 50
Appendix -
FAQ
1. My POWER light is not on?
Power is not being supplied to the unit. Please use the power
supply shipped with the unit and verify that a power source
is active from the attached power outlet used to connect the
adapter. You can test this by plugging in any other electrical
device and verify its operation. After using the power supply
shipped with the product, checking the power source, and
reinserting the power connector into the IP Camera, please
call our Support Center. The power supply may be defective.
2. My ACTIVE light is not flashing?
Verify the power supply to the unit. Power off the unit and
back on again, wait 1 minute, if the ACTIVE light still does
not begin to flash, you will have to set the unit to its factory
default (THIS WILL DELETE ANY CONFIGURATION AND SET
THE UNIT TO THE FACTORY DEFAULTS). Power on the unit
and insert the end of a paper clip into the small recessed
opening on the back of the unit. Use the clip to press the
button located within that opening.
8. How do I “PING” an IP address?
1) Open an MS-DOS (or Command) prompt
2) At the prompt type - “ping xxx.xxx.xxx.xxx” (without the
quotes and replace the “x” s with an IP address)
3) Press Enter
9. I’m accessing my video server remotely over the Internet
and the video stream is choppy, is this normal?
Yes. The frames per second received remotely are
determined by your bandwidth capabilities both at your site
where the IP Camera is installed and your remote location.
The lower of the two sites will determine how fast your
video stream is received. It is recommended to have at least
a 256Kb/sec upstream connection from the site where the IP
Camera is installed. Lower speeds will operate properly,
but provide poor remote performance. The Faster the
Internet connection at both ends, the faster the video
stream.
3. My LINK light is not flashing or solid?
Verify the cable connection. 99% of the time the cable’s
connection to the unit is causing this problem. Try using a
different network cable or crossover cable (for PC connection
only). Try reinserting the cable, if this still doesn’t solve the
problem call our Support Center.
4. I can access the video server on my LAN, but not from the
Internet.
Verify that your router (if applicable) has port forwarding
properly configured. If accessing from our DDNS service,
verify correct serial number. Firewall issues may prevent user
access.
5. How do I open an MS-DOS or Command Prompt?
Start > (All) Programs > Accessories > Command Prompt
6. How do I find out my IP address information if my settings
were automatically detected?
1) Open a Command Prompt
2) At the prompt type -”ipconfig / all” (without the quotes)
3) Near the end of the information supplied, should be your
current IP address, subnet mask, default gateway and DNS
servers
10. How do I enable or check VLC on my browser
Internet Explorer
Open Internet Explorer > Tools on the menu bar > Internet
Options > Security Tab > Custom Level > Scroll down and
verify that you are prompted or have enabled plug-ins to be
downloaded and executed. > click OK > restart browser.
Chrome
Open Chrome > Chrome menu settings > Advanced settings >
Individual information - content settings > Run automatically
11. How do I reset the unit to factory defaults?
Refer to the part name page and find the reset button.
Power ON the unit and use a paper clip to push the reset button
within that opening. You should then see the ACTIVE light turn
off and after a few seconds the ACTIVE light will begin to flash,
signifying a successful reboot. If the ACTIVE light does not turn
off after depressing the reset button, please try holding the
button in for a few seconds and releasing. YOU WILL LOSE ALL
DATA THAT HAD BEEN ENTERED PREVIOUSLY AND THE IP CAM
-ERA WILL BE SET TO ITS FACTORY RESETS.
7. I can’t connect!!
In the case of a connection failure.
Modem Reboot > Modem Reboot Finished > Router Reboot
> Router Reboot Finished > IP Camera Reboot > IP Camera
Reboot Finish > Verify DDNS and IP Camera connection, if
applicable.
50
Page 51
Unit: Inch (mm)
Dimension
Specications -
4.9" (125mm)
1.88" (48mm)
51
Page 52
Warranty Information
Digital Watchdog (referred to as “the Warrantor”) warrants the Camera against defects in materials or
workmanships as follows:
Labor: For the initial five (5) years from the date of original purchase if the camera is determined to be
defective, the Warrantor will repair or replace the unit with new or refurbished product at its option, at no
charge.
Parts: In addition, the Warrantor will supply replacement parts for the initial five (5) years.
To obtain warranty or out of warranty service, please contact a technical support representative at
1+ (866) 446-3595, Monday through Friday from 9:00AM to 8:00PM EST.
A purchase receipt or other proof of the date of the original purchase is required before warranty service
is rendered. This warranty only covers failures due to defects in materials and workmanship which arise
during normal use. This warranty does not cover damages which occurs in shipment or failures which are
caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse,
neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments,
improper antenna, inadequate signal pickup, maladjustments of consumer controls, improper operation,
power line surge, improper voltage supply, lightning damage, rental use of the product or service by
anyone other than an authorized repair facility or damage that is attributable to acts of God.
52
Page 53
Limits & Exclusions
There are no express warranties except as listed above. The Warrantor will not be liable for incidental or
consequential damages (including, without limitation, damage to recording media) resulting from the
use of these products, or arising out of any breach of the warranty. All express and implied warranties,
including the warranties of merchantability and fitness for particular purpose, are limited to the
applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights from vary from state
to state.
If the problem is not handled to your satisfaction, then write to the following address:
Digital Watchdog, Inc.
ATTN: RMA Department
5436 W Crenshaw St
Tampa, FL 33634
Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in
its sole discretion, are not covered. Cost of such service calls are the responsibility of the purchaser.
53
Page 54
)FBERVBSUFST0GGJDF8$SFOTIBX4U5BNQB'-
4BMFT0GGJDF#MPPNGJFME"WF$FSSJUPT$BMJGPSOJB64"
1)]'"9
XXX%JHJUBM8BUDIEPHDPN
UFDIOJDBMTVQQPSU!EXDDUW
5FDIOJDBM4VQQPSU1)
64"$BOBEB
*OUFSOBUJPOBM
'SFODI$BOBEJBO
5FDIOJDBM4VQQPSU)PVST.POEBZ'SJEBZ
BNUPQN&BTUFSO4UBOEBSE5JNF
Loading...