Before installing or operating the camera, please read and follow this manual carefully.
Rev.:08/26
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation, for it may be dangerous and can cause
damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other
damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect the camera from humidity and dust.
Protect the camera from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.
Cleaning: To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface: The material of the mounting surface must be strong enough to support the camera. Q
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference, when the equipment
is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful interference to radio
communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
Parts & Description............................................................................................................................................................................5
Inside the Box ....................................................................................................................................................................................7
MEGApix® 1080p™ Camera Setup................................................................................................................................11
Using DW Desktop Tool™ ........................................................................................................................................................12-13
Camera Reboot.................................................................................................................................................................................15
MEGApix® 1080p™ Camera Web Viewer....................................................................................................................16
Accessing the Camera’s Web Viewer......................................................................................................................................16
Live Buffering Selection.................................................................................................................................................................18
MEGApix® 1080p™ Camera Setup...............................................................................................................................19
Dual Codecs (H.264, MJPEG) with Simultaneous Streaming
4.0mm Fixed Lens
Smart IR™ with Intelligent Camera Sync. 30ft Range (IR models)
True Day/Night with Mechanical IR Cut Filter
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Auto White Balance (AWB)
Programmable Privacy Zones
Motion Detection
Web Server Built-in
PoE and DC12V
OnVIF Compliant, Profile S
Water Proof Cabling
4
PARTS & DESCRIPTIONS*
5
DIMENSIONS (MM)*
6
INCLUDED IN THE BOX*
7
NETWORK CONNECTION*
There are two way to power a MEGApix® 1080p™ camera.
Use a PoE- enabled switch to connect data and power through a single
cable and begin viewing and recording images instantly. A non- PoE switch
will require an adaptor for power transmission.
1.Using a PoE-Enabled Switch
The MEGApix® 1080p™ Camera is PoE-Compliant, allowing transmission of power and data via a
single Ethernet cable. PoE eliminates the need for the different cables used to power, record, or
control the camera. Follow the illustration below to connect the camera to a PoE-enabled switch
using an Ethernet cable.
2.Using 12VDC
If a PoE injector is not available, use a power adaptor for power transmission and a non-PoE switch
for data transmission. Follow the illustrations below to connect the camera without a PoE Injector.
8
INSTALLATION*
Easy Camera Installation
1.The mounting surface must bear five times the weight of
your camera.
2.Do not let the cables get caught in improper places or the
electric line cover to be damaged. This may cause a
breakdown or fire.
3.For the installation process, remove the dome cover from
the camera module. Insert a coin or screwdriver between the
camera's base and dome and twist to pry the dome cover
open.
4.Using the mounting template or the camera itself, mark
and drill the necessary holes in the wall or ceiling.
5.Pass wires through and make all necessary connections.
See page 8 for information on the network connection
options.
6.Fix the camera on to the mounting surface using the
screws included with the camera.
9
INSTALLATION*
Easy Camera Installation – Adjusting the Camera Tilt
Adjust the camera's pan and tilt. Tighten the pan/tilt screw on
the camera's bracket until it is secured properly. Use the
camera’s 3-Axis gimbal to adjust the camera’s tile and angle.
The camera’s maximum tilting angle is 70°.
Easy Camera Installation – Dismounting the Camera
To dismount the camera:
1. Hold the camera's dome firmly and turn it clockwise.
2. The camera's screw mechanism will allow you to remove the camera from the mounting
quickly and easily.
10
DW Desktop Tool™ *
Installing DW Desktop Tool™ Software
DW Desktop Tool™ searches for all available Digital Watchdog devices
currently connected to your network.
1.Install DW Desktop Tool to find the MEGApix® 1080p™ camera on your local network. The
software can be found on the included User Manual CD. Run DW Desktop Tool and install onto
your PC.
2.When setup is complete, launch DW Desktop Tool.
3.The software will automatically search your network for all Digital Watchdog® supported devices.
Your camera will appear as ”DWC-MD724V / DWC-MD72I4V.”
4.Double-click on the camera name and select ‘View Camera Website’ to launch the camera’ web
viewer.
*Install the DW Desktop Tool to a computer located on the same Subnet Mask as the MEGApix® 1080p™
camera.
11
DW Desktop Tool™ *
Using DW Desktop Tool™ Software
Use DW Desktop Tool™ to change the basic settings of your MEGApix®
camera or to connect to your MEGApix® camera.
12
DW Desktop Tool™ *
Using DW Desktop Tool™ Software
Use IP Finder to set the connection type and the IP address information
for your MEGApix® 1080p™ camera.
1.DHCP: Select DHCP to access the camera within the same internal network. For further
explanation on DHCP, please see page 15.
2.Static IP: Select Static to connect to the camera from an external network. For further
explanation on Static, please see page 15.
*If you change the camera’s IP, write down the camera’s MAC Address for identification in the future.
13
DW Desktop Tool™ *
DHCP
The Dynamic Host Configuration Protocol (DHCP) is a network configuration protocol that allows a
device to configure automatically according to the network it is connected to.
If your network supports DHCP and your MEGApix® 1080p™ camera is set to DHCP, IP Finder will
automatically find and set your MEGApix® 1080p™ camera to correspond with your network
requirements.
Static
Static IP addresses are recommended when using a network that does not support DHCP or when
setting your device to be accessed externally via the internet. If Static is selected, you must manually
enter the correct network settings for your MEGApix® 1080p™ camera. The settings will correspond
with your network. To set your camera to a static IP address, we recommend that you (1) setup the
camera to DHCP, (2) allow it to configure itself according to your network, and (3) change the settings
to a static IP address.
1.To set your MEGApix® 1080p™ camera to Static, highlight the desired device from the search
results list, and click on Configuration. In the “Network Configuration” window, make sure Static
is selected.
2.Enter the following information: IP Address, Netmask, Gateway, and Preferred DNS.
3.Click Apply and Reboot to save all changes.
14
Loading...
+ 31 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.