Digital Watchdog DWC-MC553WTIR Quick Start Guide

Quick Start Guide Quick Start Guide

Test Video Cable

Color Deco Rings

Screw &

Test Video Cable

Color Deco Rings

Screw &

Plasc Anchor-4pcs

Test Video Cable

Color Deco Rings

Screw &

Plasc Anchor-4pcs

Test Video Cable

Color Deco Rings

Screw &

Plasc Anchor-4pcs

Test Video Cable

Color Deco Rings

Color d eco
rings

Test video
cable

Screw and
plastic
anchor-4pcs

DWC-MC 553WTIR

WHAT’S IN THE BOX

Tem p la te

1 Set

sheet

Quick S etup

1 Set

Guide

Torque

1 Set

wrench

1 Set

1 Set

1 Set

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the weight of
your camera.

2. Do not let the cables get caught in improper places or the electric
line cover can be damaged. This may cause a short or fire.

3. Use the mounting template to mark and drill the necessary holes in
the mounting surface.

4. The camera has a manual IR switch, located under the camera’s
lens. You can use this switch to manually turn the IR LEDs on or o
to match your installation needs.

IR Switch

ON/OFF

STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES

Pass the wires through the mount bracket and make all

necessary connections. Connect the BNC cable and power
cables to the camera.

Power

Requirements

DC12V

Power Consumption

DC12V (LED o ): 1.98W, 165mA
DC12V (LED on): 2.62W, 218mA

External
OSD and
signal
controller

NOTE: Download all your suppor t materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by ente ring th e part number in
the ‘Searc h by Prod uct ’ sea rch bar. Result s for
applicable part numbers will populate automatically
based on the part number you e nter.

3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results .

Attention: This document is intended to serve as a quick reference for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.

Tel: [phone]

Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday

1 Set

EXTERNAL CONTROLLER

digital-watchdog.com

THE CAMERA

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:

a. Enter the camera’s OSD menu. You can access it locally from
using the camera’s joystick in the body of the camera, or from a
recorder supporting UTC communication. Go to SETUP >
OUTPUT > ANALOG MODE.

b. Set the camera’s analog signal output from the following
options:

• HD-A: supports 5MP/1944p @ 20fps and 12.5fps, 4MP/1440p
@ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.

Quick Start Guide

STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN

1. Once all cables have been connected, use the screws included
with the camera to properly mount and secure the camera to the
mounting surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired
view. The cameras’ max angles are:

Pan: 0° ~ 360°

Tilt: 0° ~ 70°

Rotation: 0° ~ 360°

3. Once the installation is complete, remove the protective film from
the camera’s dome cover. To remove it, loosen the screw on the
decorative ring and rotate the ring counter-clockwise to remove.

• HD-T: supports 5MP/1944p @ 20fps, 4MP/1440p @ 30fps,

2.1MP/1080p @ 30fps and 720p @ 30fps.

• HD-C: supports 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps
and 720p @ 30fps.

• CVBS: supports up to 960H @ 30fps

c. Change CONFIRM to ON to save the changes.

d. Go to the EXIT menu and select SAVE&EXIT to save all changes.
The camera signal automatically.

Rotation 360°

Panning 360°

Tilting 70°

Rev Date: 0 6/1 9

Speci fications an d pricing are subjec t to change with out notice.

Copyright © Digital Watchdog. All rights reserved.