Digital Watchdog DWC-D3763TIR User Manual

Analog High Definition
Indoor Dome Camera

DWC-D3763TIR

12/15

PRECAUTIONS

Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

2

TABLE OF CONTENTS

Table of Contents

Introduction

Installation

Module OSD Menu

Troubleshooting

Warranty Information

Specifications

Features
Parts and Descriptions
Dimensions

Inside the Box
Easy Installation
Connecting to Monitors 9
Control Board
Adjusting the Camera Lens

Adjusting the Camera Angle

13-28

30-31

32-33

3

4
5
6

7
8

10
11

12

29

FEATURES*

Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
1/2.7” CMOS Sensor
1080P Resolution at 30fps
Varifocal P-Iris Lens 2.8~12mm
Smart IR™ with Intelligent Camera Sync. 100ft Range
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter
OSD Control via Coax Cable using UTC
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)

4

PARTS & DESCRIPTION*

1

Bottom Case

2

Camera Gimbal

3

Upper Case

4

Dome Cover

3

4

Set Screw

1

2

5

DIMENSIONS IN MILLIMETERS (IN)*

89.0 3.50”

81.0 3.19”

6

120.0 4.72”

9.0 0.3539.0 1.53”

89.4 3.52”

INSIDE THE BOX*

Included with your Camera:

1

User Manual

2

Mounting T emplate

3

2 Machine Screws and 2 Dry Wall Anchors

4

Secondary Video-BNC Cable

Analog High Definition
Indoor Dome Camera

DWC-D3763TIR

10/08

7

EASY INSTALLATION*

1. To detach the camera’s cover dome from the camera’s module
press the small buttons located at the sides of the cover dome.
While pressing the buttons, disconnect the cover dome from the
camera’s base module.

2. Use the camera or mounting template to mark and drill the
necessary holes in the wall or ceiling.

3. Pull wires through and make connections.

4. Using the two (2) included screws, mount and secure the
camera to the wall or ceiling.

5. Adjust the camera’s Pan and Tilt. See page 12 for more
information.

6. Use the joystick to adjust the OSD menu. See pages
13-21 for more information.

7. Snap the camera’s cover dome to the camera base to complete
the installation.

8

CONNECTING TO MONITORS*

Use the diagram below to connect to a Monitor or CRT Monitor properly.

12VDC

Second Video Output

Monitor

Power Connection - 12VDC

Left

Down

CCTV Monitor

Up

Right

9

CONTROL BOARD*

Joystick: Controls
the OSD menu.

1

Remove the camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control the camera’s OSD options.

10

Secondary Connector:
Video Output Connector for
On-Site Configuration

ADJUSTING THE CAMERA LENS*

Follow the instructions provided below to make any lens adjustments.

ZOOM

FOCUS

Zoom:

Wide - Tele

Focus:

Far - Near

1

To adjust the field of view, use the L-Key to turn the zoom screw (located on the bottom of the
camera) counter-clockwise to zoom in, or clockwise to zoom out.
Adjust the focus the same way as described above AFTER the desired zoom position is established.

11