Digital Watchdog DWC-D3661TIR, DWC-D3661T User Manual

Starlight MPA
Indoor Dome Camera

DWC-D3661T
DWC-D3661TIR

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.

07212014

PRECAUTIONS

Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damage.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth wi h a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residen ial environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

2

TABLE OF CONTENTS

Introduction

Installation

Module OSD Menu

Troubleshooting

Warranty Information

Specifications

Features
Parts and Descriptions
Dimensions

Inside the Box
Easy Installation
Connecting to Monitors
Control Board
Adjus ing the Camera Lens 11
Adjus ing the Camera Gimbal 12

13-25

27-28

29-30

3

4
5
6

7
8
9

10

26

FEATURES*

1/3" Sony 1.3M CMOS
820 TV Lines [B/W], 800 TV Lines [Color]

2.8~12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync, Smart IR [DWC-D3661TIR]
True Day & Night with IR Cut Filter
3D DNR (3D Digital Noise Reduction)
WDR (Wide Dynamic Range)
Star-Light (Super Low Light Technology)
HME (Highlight Masking Exposure)
Defog (Extreme Weather Image Copmensation)
Digital Quick Zoom & 8x Digital Zoom
16:9 and 4:3 Viewing Modes
AGC / BLC / AWB
Privacy Zones (16) & Motion Detec ion
Camera Control via RS-485/ UTC
RS485, UTP, & 1 Alarm Output Built-In
Secondary BNC Output

4

PARTS & DESCRIPTION*

1

Bottom Case

2

Camera Gimbal

3

Upper Case

4

Dome Cover

5

BNC Cable

6

DC12V Cable

7

UTP Cable

8

RS485 Cable

9

Alarm Output Cable

6

7

8

9

5

3

4

1

2

5

DIMENSIONS IN MILLIMETERS (IN)*

89.0 3.50”

81.0 3.19”

6

120.0 4.72”

9.0 0.3539.0 1.53”

89.4 3.52”

INSIDE THE BOX*

Included with your Camera

1

User Manual

2

Moun ing Template

3

2 Machine Screws and 2 Dry Wall Anchors

4

Secondary Video-BNC Cable
Power Cable

5

Strlght MPA
Indoor Dome Camera

DWC-D366
DWC-D366 R

AB U MA UA

B
B

0 0

7

EASY INSTALLATION*

1. To detach the camera’s cover dome from the camera’s module
press the small buttons located at the sides of the cover dome.
While pressing the buttons, disconnect the cover dome from the
camera’s base module.

2. Use he camera or mounting template to mark and drill the
necessary holes in the wall or ceiling.

3. Pull wires through and make connections.

4. Using the two (2) included screws, mount and secure the
camera to the wall or ceiling.

5. Adjust the camera’s Pan and Tilt. See page 12 for more
information.

6. Use he joystick to adjust the OSD menu. See pages
13-21 for more information.

7. Snap the camera’s cover dome to the camera base to complete
the installation.

8

CONNECTING TO MONITORS*

Use the diagram below to connect to a Monitor or CRT Monitor properly.

12VDC/24VAC

Second Video Output

Monitor

Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.

Left

Down

CCTV Monitor

Up

Right

9

CONTROL BOARD*

Joystick: Controls the OSD menu.

1

Remove he camera’s lens cover by rotating it counter-clockwise.

2

Use the Joystick to control he camera’s OSD options.

10

Secondary Connector:
Video Output Connector for
On-Site Configuration