Digital Watchdog DWC-D3563WTIR Quick Start Guide

Quick Start Guide Quick Start Guide

Test Video Cable

Sunshield cover &

Test Video Cable

Sunshield cover &

DC plug
cable

DWC-D3563WTIR

WHAT’S IN THE BOX

Screws
and pla stic

1 Set

anchors
(2pc s)

1 Set

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the weight of
your camera.

2. Do not let the cables get caught in improper places or the electric
line cover can be damaged. This may cause a short or fire.

3. Detach the camera’s dome cover by pressing on the two small
buttons located at each side of the cover dome.

4. Remove the dome protection film before placing the dome back
on the camera base.

Protection sticker

STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES

Pass the wires through the mount bracket and make all

necessary connections. Connect the BNC cable and power
cables to the camera.

Power

Requirements

DC 12 V/AC24V

dual voltage

Power Consumption

DC1 2V ( LED o ): 3 .3 W (275 mA)
DC12V (LED on): 5.9W (495mA)

AC24V (L ED o): 2.75 W (200 mA)

AC24V (LED on): 5.3W (360mA)

Tem p la te
sheet

NOTE: Download all your suppor t materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by ente ring th e part number in
the ‘Searc h by Prod uct ’ sea rch bar. Result s for
applicable part numbers will populate automatically
based on the part number you e nter.

3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results .

Attention: This document is intended to serve as a quick reference for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.

Tel: [phone]

Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday

1 Set

Quick S etup
Guide

digital-watchdog.com

1 Set

Protection film

THE CAMERA

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:

a. Enter the camera’s OSD menu. You can access it locally from
using the camera’s joystick in the body of the camera, or from a
recorder supporting UTC communication. Go to SETUP >
OUTPUT > ANALOG MODE.

b. Set the camera’s analog signal output from the following
options:

• HD-A: supports 5MP/1944p @ 20fps and 12.5fps, 4MP/1440p
@ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.

• HD-T: supports 5MP/1944p @ 20fps, 4MP/1440p @ 30fps,

2.1MP/1080p @ 30fps and 720p @ 30fps.

• HD-C: supports 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps
and 720p @ 30fps.

• CVBS: supports up to 960H @ 30fps

Quick Start Guide

STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN

1. Once all cables have been connected, use the screws included
with the camera to properly mount and secure the camera to the
mounting surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired
view. The cameras’ max angles are:

Pan: 0° ~ 360°

Tilt: 0° ~ 70°

Rotation: 0° ~ 360°

3. To adjust the camera’s focus and zoom:

a. Unlock the zoom or focus screws by rotating them

counter-clockwise.

b. Adjust the zoom and focus screws at the base of

the camera module to achieve a clear image.

c. Tighten the screws and close the front case

by rotating it clock-wise.

4. Once the installation is complete, remove the protective film from
the camera’s dome cover.

c. Change CONFIRM to ON to save the changes.

d. Go to the EXIT menu and select SAVE&EXIT to save all changes.
The camera signal automatically.

Focus

Zoom

Rev Date: 0 6/1 9

Speci fications an d pricing are subjec t to change with out notice.

Copyright © Digital Watchdog. All rights reserved.