Digital Watchdog DWC-D2252DIR, DWC-D2362DIR, DWC-D2262DIR, DWC-D2363D, DWC-D2363TIR User Manual
...Page 1
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
ABOUT MANUAL
12232010
User Manual
Indoor Dome Camera
DWC-D2252DIR, D2262DIR, D2362DIR
DWC-D2363D, D2363TIR
DWC-D2367WD, D2367WTIR
Page 2
GG
Do not open or modify.
GG
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
G
Do not put objects into the unit.
GGGG
or other damages.
GGG
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to
high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface
The material of the mounting surface must be strong enough to support the camera.
GGGGGGGGGGGGGGGGGGGGGGGGGGG
PRECAUTIONS
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference, when the equipment is operated
in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.
WARNING
:
C
hanges or modications are not expressly approved by the manufacturer.
FCC COMPLIANCE
2
Page 3
Before sending your camera for repair, check the following or contact our technical specialist.
No Video
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup
of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus Video
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
TROUBSHOOTING
3
Page 4
4
1/3” Sony Super HAD II CCD
420 TV Lines
3.6mm Fixed Lens (D2252DIR)
3.3 ~ 12m Varifocal Auto Iris Lens (D2262DIR)
100ft Range IR with Intelligent Camera Sync
Electronic Day and Night
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
AGC / BLC / AWB
Negative Imaging
Mirror Image Control
Programmable Privacy Zone (4) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
12VDC Transformer Included
Secondary Video-BNC Output
FEATURES
*
-
D2252DIR, D2262DIR
Page 5
5
FEATURES
*
-
D2362DIR
1/3” Sony Super HADIICCD
540 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
Electronic Day and Night
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
AGC / BLC / AWB
Negative Imaging
Mirror Image Control
12VDC Transformer Included
Programmable Privacy Zone (4) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Secondary Video-BNC Output
FEATURES
*
-
D2363D
1/3" Sony Super HAD II CCD560 TV Lines
3.3~12mm Varifocal Auto Iris Lens
Electronic Day and Night
Star-Light (Super Low Light Technology)
DRC (Dynamic Range Compressor)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
Page 6
6
FEATURES
*
-
D2363TIR
1/3” Sony Super HAD II CCD
High Resolution 560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
True Day and Night / TDN5
Star-Light (Super Low Light Technology)
DRC (Dynamic Range Compressor)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Programmable Privacy Zone (8) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
BLC (Back Light Compensation)
Programmable Privacy Zone (8) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
Page 7
7
FEATURES
*
-
D2367WD
1/3” Sony Super HAD II CCD
560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
Electronic Day and Night
EWDR (Electronic Wide Dynamic Range)
Star-Light (Super Low Light Technology)
DSS (Digital Slow Shutter)
3D-DNR (3D Digital Noise Reduction)
DIS (Digital Image Stabilizer)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
Page 8
8
FEATURES
*
-
D2367WTIR
1/3” Sony Super HAD II CCD
560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
True Day and Night / TDN5
EWDR (Electronic Wide Dynamic Range)
Star-Light (Super Low Light Technology)
DSS (Digital Slow Shutter)
3D-DNR (3D Digital Noise Reduction)
DIS (Digital Image Stabilizer)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
Page 9
9
DIMENSION (mm)
*
109.6
103.1
41.3
6.5
145
117.0
125.0
5.0
4.5
91.0
91.0
85.0
85.0
L= 300mm
RS485 (Black+ & White -)
VIDEO (YELLOW)
BNC JACK
DC 12V or AC24V
5mm TWIST SOLDERING
RED
BLACK
Page 10
10
Power Requirement *
Power Wire Maximum Distance
Wire Gauge 12VDC 24VAC
24 AWG 80ft 323ft
22 AWG 128ft 513ft
20 AWG 203ft 815ft
18 AWG 323ft 1295ft
16 AWG 514ft 2056ft
14 AWG 816ft 3264ft
12 AWG 1295ft 5183ft
10 AWG 2057ft 8228ft
Coaxial Cable Type Maximum Distance
RG59/U 750ft
RG6/U 1,000feet
RG11/U 1,500feet
Power Requirement
12VDC at 1A
24VAC at 500mA
Page 11
11
INSTALLATION
*
Included with Digital Watchdog Camera:
1. User Manual
2. Mounting Template
3. Security L-Key
4. Single Sided Hex Key
5. Secondary BNC Cable for a Field Monitor
6. Four (4) Screws and Four (4) Dry Wall
Anchors
X
Z
Y
[
\
^
]
Camera Installation
Use the Mounting Template (2) when mounting the camera.
Use the Security L-Key (3) to loosen the Four Screwsthat secure the vandal-proof dome cover.
Remove the cover; then, remove the inner screw holes to mount the camera.
NOT
E
Page 12
12
INSTALLATION
*
A. Loosen the Screws (A) with the Security L-Key
included with your camera.
B. Separate the Upper Case (B) from the Base (F).
C. Cut a hole in the ceiling for routing the cables.
D. Use the Mounting Template to drill the four
s
crew holes on the surface of the ceiling.
E. Pass the Power Cable (C) and the Video Cable (E)
from the camera unit through the hole in the
ceiling.
F. Align the screw holes of the camera unit with
the ho
les in the ceiling. Secure the four screws.
G. Install and adjust the camera unit.
H. Assemble the Upper Case (B) and the Base (F).
I. Put the upper case and the base together.
J. Tighten the outer Screws (A) using the Security
L-Key.
Page 13
13
CONNECTION
*
Video Output
BNC Cable
Main Monitor
Field Test Monitor
Spot Monitor Cable
DC12V / AC24V
Page 14
14
LENS ADJUSTMENT
*
A. Move the Zoom Lever until you get the desired position.
B. Move the Focus Lever until you get the desired focus.
A. Zoom Lever
B.Focus Lever
Page 15
15
D2252DIR, D2262DIR, D2362DIR, D2363D, D2363TIR, D2367WD, D2367WTIR
CAMERA SETTING & ON-SCREEN DISPLAY
*
Field Test Monitor Video Output
RS485 Connector
Dip Switch for the IR Remote Controller
Mini Joystick for the Menu Setup
LEFT
UP DOWN
RIGHT
Page 16
16
MODULE OSD MENU*
(D2252DIR, D2262DIR, D2362DIR)
EXPOSURE COLORDAY&NIGHT
BRIGHTNESS
SHUTTER
BLC
AGC
WB MODE D&N MODE
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
SLC
HME
DRC
ALARM MASK 1
MASK 2
MASK 3
MASK 4
COLOR SET
SYNCSETUPEXIT
SYNC CAMERA ID
TITLE EDIT
TITLE RESET
TITLE POSITION
DPC SET
LANGUAGE
PC CONT.
EXIT
SAVE & EXIT
FAC TORY RESET
Page 17
17
EXPOSURE
BRIGHTNESS MANUAL (ELC LEVEL : 0 ~ 100) / DC (DC LEVEL : 0 ~ 31)
SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000
BLC
OFF / ON
BLC (Back Light Compensation)
AGC
OFF / 12dB ~ 36dB
AGC (Auto Gain Control)
COLOR
WB MODE AWC / ATW / MANUAL / PUSHLOCK (AWC is recommended.)
R-Y GAIN 0 ~ 255
B-Y GAIN 0 ~ 255
DAY & NIGHT
Day & Night Mode
AUTO / COLOR / BW
COLOR --> BW: Switching from COLOR to BW; If the number is higher, the camera will only
switch during a super low light condition.
BW --> COLOR: naht rewol syawla eb dluohs re
bmun sihT ;ROLOC ot WB morf gnihctiwS
COLOR --> BW
Read Time: Time interval to switch from COLOR to BW
COLOR:
BW: BURST (OFF/ON); When the burst is OFF, the picture will have less noise.
OSD MENU*
(D2252DIR, D2262DIR, D2362DIR)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Page 18
18
FUNCTION
MIRROR OFF/ MIRROR
SHARPNESS 0 ~ 49
GAMMA USER / 0.45 / 0.6 / 1.00
SLC
OFF / ON (0 ~ 50)
SLC (Side Light Compensation)
HME
OFF / ON (0 ~ 55)
HME (Highlight Masking Exposure)
DIS OFF /ON
DIS (Digital Image Stabilizer)
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (0 ~ 55)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT(1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Page 19
19
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
COLOR SET BLACK / GRAY / COLOR 1~ 6
SYNC
SYNC MODE INTERNAL / AUTO
V-PHASE 0 ~ 199
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT
TITLE RESET
TITLE POS.
DPC
OFF / AUTO
DPC ( Dead Pixel Cancellation)
LANGUAGE English / Chinese
PC CONT. OFF / ON
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Page 20
20
MODULE OSD MENU*
(D2363D, D2363TIR)
EXPOSURE COLORDAY&NIGHT
BRIGHTNESS
SHUTTER
BLC / HME
AGC
STARLIGHT
WB MODE
R-Y GAIN
B-Y GAIN
D&N MODE
C_SUP
A_SUP
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
FREEZE
NEGATIVE
D-ZOOM
3D DNR
DRC
MOTION PRIVACY
SYNCSETUPEXIT
SYNC TITLE EDIT
PC CONTROL
LANGUAGE
MONITOR
OSD COLOR
OMNI LENS
EXIT
SAVE & EXIT
FAC TORY RESET
Page 21
21
OSD MENU*
(D2363D, D2363TIR)
EXPOSURE
BRIGHTNESS 0 ~ 100
SHUTTER 1/60, FLK, 1/120 ~ 1/100000
BLC OFF / ON , BLC (Back Light Compensation)
AGC
HIGH / MIDDLE / LOW / OFF
AGC (Auto Gain Control)
STARLIGHT
OFF / AUTO (x2 ~ x256)
x32 is recommended.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / INDOOR / OUTDOOR / PUSHLOCK / MANUAL
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
DAY & NIGHT
Day & Night Mode
AUTO/ COLOR/ BW
COLOR --> BW: Switching from Color to BW; if the number is higher, the camera will
only switch during a super low light condition.
BW --> COLOR: Switching
from BW to color; this number should always be lower than
COLOR --> BW.
Read Time: Time interval to switch from Color to BW.
COLOR
B&W: BURST (OFF/ON); There is less noise when the BURST is OFF.
C-SUP
Color Suppression:
Color will be reduced at low illumination, if the C-SUP Level is higher. 0 ~
100 (Not Available when 3D-DNR is On.)
A-SUP
ApertureSuppression:
The sharpness of the edges will be reduced at low illumination, if A-SUP
Level is higher. 0 ~ 100 (Not Available when 3D-DNR is On.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Page 22
22
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00 / USER
FREEZE OFF / ON
NEGATIVE OFF/ ON
3D-DNR
OFF / ON (0 ~ 100)
3D-DNR (3D Digital Noise Reduction)
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
DRC
OFF / INDOOR / OUTDOOR
DRC (Dynamic Range Compressor)
HME
OFF / ON
HME (Highlight Masking Exposure)
DIS
OFF / ON
DIS (Digital Image Stabilizer)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Page 23
23
Protocol is PELCO-D. It is hardcoded into the DSP, so it cannot be changed.
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
MASK 7 OFF / ON
MASK 8 OFF / ON
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
V-PHASE 0 ~ 199
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT OFF / ON
DPC
OFF / ON
Dead Pixels Cancellation
MONITOR CRT / LCD
LANGUAGE English,Japanese, Chinese
BAUDRATE
2400 / 4800 / 9600 / 14400 / 19200 / 38400.
OMNI LENS OFF / 1 ~ 10 (OMNI-Plus Cameras Only)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
Page 24
24
MODULE OSD MENU*
(D2367WD, D2367WTIR)
EXPOSURE COLORDAY&NIGHT
BRIGHTNESS
SHUTTER
BLC
AGC
MAX_DR
STARLIGHT
WB MODE
R-Y GAIN
B-Y GAIN
D&N MODE
C_SUP
A_SUP
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
FREEZE
NEGATIVE
3D DNR
D-ZOOM
SLC
HME
DIS
MOTION MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
SYNCSETUPEXIT
SYNC CAMERA ID
TITLE
DPC
MONITOR
LANGUAGE
BAUDRATE
OMNI LENS
EXIT
SAVE & EXIT
FAC TORY RESET
Page 25
25
OSD MENU*
(D2367WD, D2367WTIR)
EXPOSURE
LENS DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000
BLC
OFF / ON
BLC (Back Light Compensation)
AGC
HIGH / MIDDLE / LOW / OFF
Auto Gain Control
MAX-DR OFF /ON (0~ 20) (Electronic Wide Dynamic Range)
STARIGHT
OFF / AUTO (x2 ~ x256)
x32 is recommended.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
DAY & NIGHT
Day & Night Mode
AUTO/ COLOR/ BW / EX-CONT
COLOR --> BW: Switching fromcolor to BW; if the number is higher, the camera will only switch during a
super low light condition.
BW --> COLOR: Switching from BW to color; this number shoul
d always be lower than COLOR --> BW.
Read Time: Time interval to switch from Color to BW.
COLOR
B&W: BURST (OFF/ON); There is less noise when the BURST is OFF.
C-SUP
Color Suppression:
Color will be reduced at low illumination, if the C-SUP Level is higher. 0 ~ 100 (Not Available
(Not Available when 3D-DNR is On.)
A-SUP
ApertureSuppression:
The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher. 0 ~ 100
(Not Available when 3D-DNR is On.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Page 26
26
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00 / USER
FREEZE OFF / ON
NEGATIVE OFF/ ON
3D-DNR
OFF / LOW / MIDDLE / HIGH
3D Digital Noise Reduction
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
SLC OFF / ON Side Light Compensation
HME
OFF / ON
Highlight Masking
Exposure
DIS
OFF / ON
Digital Image Stabilizer
EXIT JUMP EXIT / SAVE&EXIT / FAC TORY SET
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FAC TORY SET
Page 27
27
Protocol is PELCO-D. It is hardcoded into the DSP, so it cannot be changed.
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
V-PHASE 0 ~ 199
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT OFF / ON
DPC
OFF / AUTO
DPC (Dead Pixels Cancellation)
MONITOR CRT / LCD
LANGUAGE English,Japanese, Chinese
BAUDRATE
2400 / 4800 / 9600 / 14400 / 19200 / 38400.
OMNI LENS OFF / 1 ~ 10 (OMNI-Plus Cameras Only)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
Page 28
28
SPECIFICATIONS*
Model D2252DIR / D2262DIR
Camera TYPE Color/BW
Indoor Dome Camera
Mount Surface
Image Device Super HAD
II
CCD
Size 1/3"
Pixels-Total537(H) x 505(V)
510(H) x 492(V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED ON 0.0 Lux
Functions BLC ON / OFF (Area Setting)
AGC ON / OFF (Gain Adjust)
AWB ATW / AWC / MANUAL / PUSH LOCK
DRC ON / OFF
Motion Detection ON / OFF
Privacy Zone 4 Programmable Zone
/ Size
Lens (D2252DIR) Focal Length 3.6mm Fixed Lens
Lens (D2262DIR) Focal Length 3.3 ~ 12mm Varifocal Auto Iris Lens
Resolution Horizontal 420 TV Lines
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10 ~ +55(14එ ~ 131
එ
)
Humidity Less than 90%
Power Power Requirement 12VDC
Power Consumption
0.9W, 75mA / 2.9W, 242mA (LED ON)
Dimensions(φ x H) 110.3 X 134.9mm, 4.34 X 5.31in
Page 29
29
SPECIFICATIONS*
Model D2362DIR
Camera TYPE Color/BW
Indoor Dome Camera
Mount Surface
Image Device Super HAD II CCD
Size 1/3"
Pixels-Total 811(H) x 508(V)
768(H) x 494(V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED On 0.0 Lux
Functions BLC ON / OFF (Area Setting)
AGC ON / OFF (Gain Adjust)
AWB ATW / AWC / MANUAL / PUSH LOCK
DRC ON / OFF
Motion Detection ON / OFF
Privacy Zone 4 Programmable Zone / S
ize
Lens Focal Length 3.3 ~ 12mm Varifocal Auto Iris Lens
Resolution Horizontal 540 TV Lines [at TDN (B/W) :560 TV Lines]
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10 ~ +55(14එ ~ 131එ)
Humidity Less
than 90%
Power Power Requirement 12VDC
Power Consumption
0.9W, 75mA / 2.9W, 242mA (LED ON)
Dimensions(φ x H) 110.3 X 134.9mm, 4.34 X 5.31in
Page 30
30
SPECIFICATIONS*
Model D2363D
Camera TYPE Color/BW
Indoor Dome Camera
Mount Surface
Image Device Super HAD II CCD
Size 1/3”
Pixels-Total 811 (H) x 508 (V)
768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination F1.2 0.14 Lux [Color], 0.03 Lux [B/W]
Functions BLC ON/OFF
AGC HIGH / MIDDLE / LOW / OFF
DRC OFF / INDOOR / OUTDOOR
STAR-LIGHT OFF / AUTO (x2 ~ x256)
3D-DNR OFF / ON (0~100)
Privacy Zone 8 Programma
ble Zone / Size
Lens Focal Length 3.3~12mm Varifocal Auto Iris Lens
Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW]
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10~ +55(14එ~ 131
එ
)
Humidity Less than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption
Dimensions 110.3 X 134.9mm, 4.34 X 5.31in
Weight
0.6lbs
FCC, RoHS, CE
12VDC: 1.96W, 163.3mA / 24VAC: 2.2W, 91.7mA
Page 31
31
SPECIFICATIONS*
Model D2363TIR
Camera TYPE Color/BW
Mount Surface
Image Device Super HAD II CCD
Size 1/3”
Pixels-Total 811 (H) x 508 (V)
768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED On 0.0Lux
IR Distance 100ft Range
Functions BLC ON/OFF
DRC OFF / INDOOR / OUTDOOR
STAR-LIGHT OFF / AUTO (x2 ~ x256)
3D-DNR OFF / ON (0~100)
HME OFF / ON
Privacy Zone 8 Programmable Z
one / Size
Lens Focal Length 3.3~12mm Varifocal Auto Iris Lens
Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW]
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10~ +55(14එ~ 131එ)
H
umidity Less than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption
12VDC: 1.96W, 163.3mA / 24VAC: 2.2W, 91.7mA
12VDC: 4.3W, 358.3mA / 24VAC: 3.0W, 125mA (LED ON)
Dimensions 110.3 X 134.9mm, 4.34 X 5.31in
Weight
0.8lbs
FCC, RoHS, CE
Indoor Dome Camera
Page 32
32
SPECIFICATIONS*
Model D2367WD
Camera TYPE Color/BW
Mount Surface
Image Device Super HAD II CCD
Size 1/3”
Pixels-Total 811 (H) x 508 (V)
768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination F1.2 0.14 Lux [Color], 0.03 Lux [B/W]
Functions DIS ON/OFF
AGC HIGH / MIDDLE / LOW / OFF
EWDR OFF / ON
Mirror OFF / MIRROR / V-FLIP / ROTATE
STAR-LIGHT OFF / AUTO (x2 ~ x256)
Privacy Zone 6 Programmable Zone / Si
ze
Lens Focal Length 3.3~12mm Varifocal Auto Iris Lens
Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW]
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10~ +55(14එ~ 131එ)
Humidity Less
than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption
12VDC: 1.8W, 150mA / 24VAC: 2.4W, 100mA
Indoor Dome Camera
Page 33
33
SPECIFICATIONS*
Model D2367WTIR
Camera TYPE Color/BW
Mount Surface
Image Device Super HAD II CCD
Size 1/3”
Pixels-Total 811 (H) x 508 (V)
768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED On 0.0 Lux
IR Distance 100ft Range
Functions AGC HIGH / MIDDLE / LOW / OFF
STAR-LIGHT AUTO (x2 ~ x250) / OFF
3D-DNR OFF / ON
HME OFF / ON
DIS OFF / ON
Privacy Zone 6 Programmable Zone / Siz
e
Lens Focal Length 3.3~12mm Varifocal Auto Iris Lens
Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW]
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10~ +55(14එ~ 131එ)
Humidity Less
than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption
12VDC: 1.8W, 150mA / 24VAC: 2.4W, 100mA
12VDC: 4.6W, 383.3mA / 24VAC: 4.9W, 204.2mA
Indoor Dome Camera
Page 34
34
Digital Watchdog (referred to as “the Warrantor”)
warrants the Camera Series against defects in
materials or workmanship as follows.
LABOR : For the initial ve (5) years from the date of original purchase,
if the camera is determined to be defective,
the Warrantor will repair or replace the unit, with new or refurbished
product at its option, at no charge.
PARTS : In addition, the Warrantor will supply
replacement parts for the initial ve (5) years.
To obtain warranty or out of warranty service,
please contact a Technical Support Representative at
1-866-446-3595 Monday through Friday from 8:30AM to 8:
00PM Eastern.
A purchase receipt or other proof of the original purchase date is required
before warranty service is rendered. This warranty only covers failures due to
defects in materials and workmanship which arise during normal use.
This warranty does not cover damage which occurs in shipment or failures
which are caused by products not supplied by the Warrantor or failures
which result from accident, misuse, abuse, neglect, mishandling,
misapplication, alteration, modication, faulty installation, set-up adjustments,
improper antenna, inadequate signal pickup, maladjustment of consumer controls,
improper operation, power line surge, improper voltage supply, lightning damage,
rental use of the product or service by anyone other than an authorized repair
facility or damage that is attributable to acts of God.
WARRANTY INFORMATION*
Page 35
35
LIMITS AND EXCLUSIONS*
There are no express warranties except as listed above.
The Warrantor will not be liable for incidental or consequential
damages, including without limitation and damage to recording media,
resulting from the use of these products or arising out of any breach
of the warranty. All express and implied warranties, including the
warranties of merchantability and tness for particular purpose,
are limited to the applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not
apply to you. This warranty gives you specic legal rights, and you
may also have other rights that vary from state to state.
If the problem is not handled to your satisfaction,
then write to the Address listed on the next page.
Service calls which do not inv
olve defective materials or
workmanship as determined by the Warrantor, in its sole
discretion, are not covered. Costs of such service calls are
the responsibility of the purchaser.
Page 36
5436 W Crenshaw St. Tampa, FL 33634
Tel: 866-446-3595 / 813-888-9555
Fax: 813-888-9262
www.Digital-Watchdog.com
technicalsupport@dwcc.tv
Technical Support Hours: Monday-Friday
8:30am to 8:00pm EST
Loading...