Digital Watchdog DWC-B6763TIR User Manual
STAR-LIGHT AHD
TM
Analog High Definition
Bullet Camera
DWC-B6763TIR
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
08/16
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
2
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Installation Instructions
Connecting to Monitors 9
Control Board
Adjusting the Camera Angle
12-27
29-30
31-32
3
4
5
6
7
8
10
11
28
FEATURES*
Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
1/2.7” CMOS Sensor
1080P Resolution at 30fps
Varifocal P-Iris Lens 2.8~12mm
Smart IR™ with Intelligent Camera Sync. 100ft Range
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter
Secondary Video-BNC Output
OSD Control via Coax Cable using UTC
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)
IP66 Certified (Weather Resistant)
4
PARTS & DESCRIPTION*
4
5
6
Mounting Bracket
1
Camera Module
2
Sunshield Adjusting Screws
3
Sunshield Cover
4
5
IR Module
6
Front Case
3
7
OSD Joystick Controller
8
BNC Cable
9
12VDC Power Outlet
9
8
1
2
Set Screw
7
5
DIMENSIONS IN MILLIMETERS (IN)*
224.5 8.83
61.5 2.42
6
73.7 2.90
96.7 3.81
112.0 4.41 94.0 3.70
4.2 0.17
78.0 3.07
INSIDE THE BOX*
Included with Bullet Camera:
1
User Manual
2
Mounting T emplate
3
4 Machine Screws and 4 Dry Wall Anchors
Analog High Definition
Bullet Camera
DWC-B6763TIR
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
05/2015
4
Secondary Video-BNC Cable
5
L-Key
7
INSTALLATION INSTRUCTIONS*
1. Using the mounting template or your own camera,
mark and drill the necessary holes to mount the
bracket to a wall or ceiling.
2. Pull all necessary wires through and make the
proper connections.
3. Use the four (4) mounting screws to install
the camera on the wall or ceiling.
NPT 3/4” Pipe
*Installation Using a Junction Box
*Note: Electrical junction box and
required screws sold separately.
8
CONNECTING TO MONITORS*
Use the diagram below to connect to an AHD DVR or CRT Monitor properly.
12VDC
Left
Second VVideo Output
Monitor
Power Connection - 12VDC
All cameras are equipped with a second video output for on-site configuration.
AHD DVR
Up
Right
Down
9
CONTROL BOARD*
Joystick: Controls the OSD menu.
1
Remove the camera’s lens cover by rotating it counter-clockwise.
2
Use the Joystick to control the camera’s OSD options.
10
Secondary Connector:
Video Output Connector for
On-Site Configuration
ADJUSTING THE CAMERA ANGLE*
CAUTION :
1
Do not rotate more than 360o.
2
Do not unnecessarily twist too many times.
11
Loading...