Digital Watchdog DWC-B1567WTIR User Manual
960H Outdoor Bullet Camera
Double Arm Bracket
DWC-B1567WD
DWC-B1567WTIR
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
11192012
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.
WARNING : Changes or modifications are not expressly approved by the manufacturer.
22
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installation
Connecting to Monitors _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control Board _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Adjusting the Lens
Camera Setting Angle
4
5
6
7
8
9
10
11
12
13-29
30
31-32
33-34
3
FEATURES*
DWC-B1567WD / DWC-B1567WTIR
1/3” 960H High Resolution CCD
700 TV Lines
3.3~12mm Varifocal Auto Iris Lens
True Day and Night (DWC-B1567WTIR only)
Star-Light (Super Low Light Technology)
EWDR (Electronic Wide Dynamic Range)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Negative Imaging
Mirror Image Control
RS485 Built-in
Programmable Privacy Zones (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
100ft Range IR with Intelligent Camera Sync (B1567WTIR only)
IP66 Certified, No Fog or Condensation
4
PART & DESCRIPTIONS*
11
1
1
Front Case
2
Zoom, Focus Housing
3
Sunshield
4
Lens
5
3
No IR
9
10
RS 485
12
13
IR
6
2
4
5
Rear Case
6
Control Board
7
Control Cap
8
Double Arm Bracket
5
8
7
9
BNC Jack
10
Power Input Connector
DC 12V / AC24V Voltage
11
Assembly Screw
12
Fixing Screw
13
Set Screw
DIMENSIONS IN MILLIMETERS (INCHES)*
230(9.05”)
86.5(3.40”)
122(4.80”) 96.5(3.79”)
68.0(2.67”)
86.5(3.40”)
No IRIR
78.0(3.07”)
5(0.19”)
96.0(3.77”)
6
INSTALLATION*
1. User Manual
2. Mounting Template
3. Four (4) Screws and Four (4) Dry Wall Anchors
4. Second Video Jack
5. Tool
6. L-Wrench
7
EASY INSTALLATION*
*Installation Using a Junction Box
*Note: Electrical junction box and required screws sold separately.
Use the 4 mounting screws to install the camera on the
wall or ceiling.
Then, follow the next step on the pages 9-12.
NPT 3/4” Pipe
8
CONNECTING TO MONITORS*
12VDC/24VAC
CCTV Monitor
Up
RightLeft
2nd Video Output
Monitor
30cm
Power Connection - 12VDC/24VAC Dual Voltage (Auto polarity detection and protection)
All cameras are equipped with a service monitor output on the camera module.
9
Down
CONTROL BOARD*
Secondary Connector
Joystick
To Access Control Board:
[1] Remove clear plastic ring from the
control cap.
[2] Turn Control Cap counter-clockwise
until cap separates completely from the
camera body.
Functions:
[1] Joystick -
Controls the OSD menu.
[2] Secondary Connector -
T ests video output connector.
10
ADJUSTING THE VARIFOCAL DC AUTO IRIS LENS*
Follow the instructions provided below to make any lens adjustments.
1
To adjust the field of view, use the L-Wrench to turn the zoom screw (located
on the bottom of the camera) counter-clockwise to zoom in, or clockwise to zoom out.
2
Adjust the focus the same way as described above AFTER the desired zoom position
is established.
11
Loading...