How it Works
Digital Projection
Loading...
P
R
S
T
Loading...
Loading...
Titan Laser
Series Manual
30 pgs8.07 Mb0

Digital Projection Titan Laser, Titan Laser 37000 WU, Titan Laser 33000 4K-UHD Series Manual

Download
Page 1
Rev A January 2019
119-708
Titan Laser Series 4K-UHD & WUXGA Models
Super High Brightness Digital Video Projector
Important Information
Page 2
Rev A January 2019
Page 2
Important Information
Digital Projection
Digital Projection Asia
16 New Industrial Road #02-10 Hudson Technocentre Singapore 536204
Tel (+65) 6284-1138 Fax (+65) 6284-1238
www.digitalprojectionasia.com
Digital Projection Inc.
55 Chastain Road, Suite 115 Kennesaw, GA 30144, USA
Tel (+1) 770 420 1350 Fax (+1) 770 420 1360
powerinfo@digitalprojection.com www.digitalprojection.com
Digital Projection China
中国 北京市 朝阳区 芍药居北里101号 世奥国际中心A座2301室(100029)
Rm A2301 ShaoYaoJu 101 North Lane Shi Ao International Center Chaoyang District Beijing 100029, PR CHINA
Tel (+86) 10 84888566 Fax (+86) 10 84888566-805
techsupport@dp-china.com.cn www.dp-china.com.cn
Digital Projection Limited
Greenside Way, Middleton Manchester M24 1XX, UK
Registered in England No. 2207264
Registered Oce: as above
Tel (+44) 161 947 3300 Fax (+44) 161 684 7674
enquiries@digitalprojection.co.uk service@digitalprojection.co.uk
www.digitalprojection.co.uk
Digital Projection Taiwan
186 Ruey Kuang Rd, Neihu District, Taipei, 114 Taiwan
Tel +886-8797-2088 x8854 Taiwan@digitalprojection.co.uk
Digital Projection Japan
〒105-0012 東京都港区芝大門2-1-14
2-1-14 Shibadaimon, Minato-ku, Tokyo, Japan 105-0012
japan@digitalprojection.co.uk www.digitalprojection.com/jp
Digital Projection FZE
Unit B4, Light Industrial Units 4, Silicon Oasis, Dubai, UAE
Tel +971 43300800 enquiries@digitalprojection.co.uk www.digitalprojection.com
Digital Projection Korea
1511, Byucksan Digital Valley 6-cha, Gasan-dong, Geumcheon-gu, Seoul, Korea
Tel +82 2 515 5303 #1417 Korea@digitalprojection.co.uk
Digital Projection India
india@digitalprojection.co.uk
Page 3
Digital Projection Titan Laser Series
Rev A January 2019
Page 3
Important Information
Super High Brightness Digital Video Projector
Important Information
Full information about operating, connecting and setting up the projector can be found in the User Manual, located on the CD.
Contents
Symbols used in the User Manual ...............................................................................................4
Electrical and physical specications ........................................................................................4
Laser precautions .............................................................................................................................5
Product labels ....................................................................................................................................6
Manufacturers ID Label and Explanatory Label ..........................................................................6
Hazard Warning Symbol and Aperture Label ..............................................................................7
Mains Information ..........................................................................................................................7
Maintenance Warning ....................................................................................................................7
Stacking and Eyebolt Usage Notices ...........................................................................................7
Eyebolt Usage Notice ....................................................................................................................7
Label locations ...............................................................................................................................8
Location of laser aperture ..............................................................................................................9
Interlock switches ............................................................................................................................9
General precautions ......................................................................................................................10
Installation precautions ................................................................................................................11
Light hazard warning .....................................................................................................................12
Light hazard distances ................................................................................................................12
Operation and conguration precautions ...............................................................................13
Compliance with international standards ...............................................................................13
RF Interference .............................................................................................................................13
Noise .............................................................................................................................................13
European Waste Electrical and Electronic Equipment (WEEE) Directive ..............................13
Basic Operation Instructions ......................................................................................................14
Positioning the screen and projector .........................................................................................14
Stacking and rigging ....................................................................................................................15
Inserting a new lens .....................................................................................................................18
Removing the lens .......................................................................................................................19
Fitting a lens hood .......................................................................................................................19
Connecting the power supply .....................................................................................................21
Switching the projector on ..........................................................................................................22
Switching the projector o ..........................................................................................................22
Selecting an input signal .............................................................................................................23
Selecting a test pattern ................................................................................................................23
Adjusting the lens ........................................................................................................................24
Adjusting the image .....................................................................................................................24
Control Panel Reference...............................................................................................................25
Remote Control Reference ..........................................................................................................27
Page 4
Rev A January 2019
Page 4
Important Information
Symbols used in the User Manual
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Electrical and physical specications
Mains Voltage Operating Temperature Storage Temperature Operating Humidity Weight Power Consumption Thermal Dissipation
Titan Laser 37000 WU Titan Laser 33000 4K-UHD
200 - 240 VAC 17A 50/60 Hz 0°C to 40°C
-20°C to 60°C 20% to 90% non-condensing 100 kg (220.5 lb) without lens 3400 W at 200 VAC 11604 BTU/hr at 200 VAC
Specications are subject to change without notice.
Page 5
Digital Projection Titan Laser Series
Rev A January 2019
Page 5
Important Information
Laser precautions
CLASS 3R LASER PRODUCT
This Laser Product is designated as Class 3R during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow laser light to be directed or reected toward other people or
reective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included
instructions are not followed.
Caution – use of controls or adjustments or performance of procedures other than
those specied herein may result in hazardous radiation exposure.
Non-laser emission. There remains non-laser emission from the projection lens. This
portion of emission has been tested per IEC/EN 62471 to be Risk Group 3.
Titan Laser 33000 4K-UHD Titan Laser 37000 WU
Laser Parameters:
Wavelength 450 nm - 460 nm
LaserPowerforclassication 333.5mW Total internal power > 100 W Apparent Source Size > 10 mm at lens stop Divergence 100 miliRadian
Page 6
Rev A January 2019
Page 6
Important Information
Product labels
Manufacturers ID Label and Explanatory Label
This includes the following information:
Product Identication
Serial Number
Certication Statement
Size 167mm x 145 mm
CCC Logo Size
9.5*7.5mm
This mark for safety report
Made in China Fabriqué en Chine
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路 英國 曼徹斯特 格林賽得路
Name of Product : DLP Projector Nom du produit: DLP Projecteur
产品名称:数字投影机 產品名稱:數位投影機
Digital Projection Limited
英国缔佳有限公司 英國締佳有限公司
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW
Risk Group 3 Warning! Do not look into the beam. No direct eye exposure to the beam is permitted. RG3 IEC EN 62471-5:2015 Hazard Distance : Refer to Manual
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
警 告：此为A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下
，
可能需要用户对干扰采取切实可行的措施
。 警告使用者：這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種 情況下，使用者會被要求採取某些適當的對策。
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser notice No.50, Dated June 24, 2007 Class 1 Laser Product IEC/EN 60825-1:2014
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007 IEC/EN 62471-1:2006
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC 60825-1:2007 / GB 7247.1-2012 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC/ EN
60825-1:2007 IEC/ EN 62471-1:2006 第一類雷射產品 IEC/ EN 60825-1:2014
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
�勿�投影机置于雨中或潮��境中以降低起火或电�风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
200-240VAC 50/60Hz 17A
(Not for China / 非中國使用 / 非中国使用)
Model / Modèle
型号/型號
Part No. / Numéro de pièce
零部件号/零部件號
Serial No. / Numéro de série.
序号/序號
Power / Puissance
电源/電源
电源 : 200-230VAC 50/60Hz 17A
Only for China/僅限中國/仅限中国
CAN ICES-3(A)/NMB-3(A)
デルタ電子株式会社
Titan User Guides
Follow link for Projector Documentation
この二次元バーコードをスキャンしてプロジェクターのデータを取得してください
请扫描条码来取得投影机的文件
프로젝터 설명서를 보려면 링크를 팔로우하십시오
Suivre le lien pour accéder à la documentation du projecteur Produktdokumentation nden Sie unter dem Link
WJ XXXX
3264652800
Fill in manufacture plant code, such as WJ, TW
Fill in Vendor’s code
Such as: CM, GG, FS....etc.
IEC/EN 60825-1:2007 IEC/EN 62471-1:2006
Not for household use
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
Made in China
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路 英國 曼徹斯特 格林賽得路
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007 第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
119-726
*W805XXXYYXXXX*
Titan Laser 33000 4K-UHD (EU)
119-705
Made in China
中国制造 中國製造
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
，
该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007 第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 37000 WU (USA)
119-725
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
*W805XXXYYXXXX*
Titan Laser 33000 4K-UHD (USA)
119-726
Made in China
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路 英國 曼徹斯特 格林賽得路
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007 第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 37000 WU (USA)
119-725
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
*W805XXXYYXXXX*
Titan Laser 37000 WU (USA)
119-725
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
Made in China
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路 英國 曼徹斯特 格林賽得路
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007 第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
119-726
*W805XXXYYXXXX*
Titan Laser 33000 4K-UHD (EU)
119-705
Made in China
中国制造 中國製造
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
，
该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007 第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 37000 WU (USA)
119-725
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
200-240VAC 50/60Hz 17A
Model / Modèle
型号/型號
Part No. / Numéro de pièce
零部件号/零部件號
Serial No. / Numéro de série.
序号/序號
Power / Puissance
电源/電源
警 告：此为A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
警告使用者：這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser notice No.50, Dated June 24, 2007 Class 1 Laser Product IEC/EN 60825-1:2014
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007
第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 33000 4K-UHD (USA)
119-726
Made in China
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路 英國 曼徹斯特 格林賽得路
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Risk Group 3 Warning! Do not look into the beam. No direct eye exposure to the beam is permitted. RG3 IEC EN 62471-5:2015 Hazard Distance : Refer to Manual
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
200-240VAC 50/60Hz 17A
，
在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser notice No.50, Dated June 24, 2007 Class 1 Laser Product IEC/EN 60825-1:2014
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007
第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 37000 WU (USA)
119-725
Page 7
Digital Projection Titan Laser Series
Rev A January 2019
Page 7
Important Information
Risk Statement
Hazard Warning Symbol and Aperture Label
Mains Information
Maintenance Warning
Stacking and Eyebolt Usage Notices
Eyebolt Usage Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Risk Group 3 Warning! Do not look into the beam. No direct eye exposure to the beam is permitted. RG3 IEC EN 62471-5:2015 Hazard Distance : Refer to Manual
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
200-240VAC 50/60Hz 17A
Model / Modèle
型号/型號
Part No. / Numéro de pièce
零部件号/零部件號
Serial No. / Numéro de série.
序号/序號
Power / Puissance
电源/電源
警 告：此为A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
警告使用者：這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser notice No.50, Dated June 24, 2007 Class 1 Laser Product IEC/EN 60825-1:2014
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007
第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 33000 4K-UHD (USA)
119-726
Made in China
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路 英國 曼徹斯特 格林賽得路
Name of Product : Projector
产品名称:投影机 產品名稱:投影機
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW IEC/EN 60825-1:2007
Risk Group 3 Warning! Do not look into the beam. No direct eye exposure to the beam is permitted. RG3 IEC EN 62471-5:2015 Hazard Distance : Refer to Manual
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
WJ XXXX
3264652800
200-240VAC 50/60Hz 17A
，
在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施
。
，
在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser notice No.50, Dated June 24, 2007 Class 1 Laser Product IEC/EN 60825-1:2014
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007
Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC/EN 60825-1:2007 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC / EN 60825-1：2007
第一類雷射產品 IEC / EN 60825-1: 2014
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture. Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
请勿将投影机置于雨中或潮湿环境中以降低起火或电击风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
*W805XXXYYXXXX*
Titan Laser 37000 WU (USA)
119-725
LASER APERTURE LASER ÖFFNUNG OUVERTURE LASER АΠЕРΤУРA ЛАЗЕРA
レ ー ザ 開 口
레이저 개구부
激光辐射之孔径 雷射輻射之孔徑
Note
注意 注意
: Input voltag e limited 200 -240V
: 输 入 电 压仅 限 200 -240 V : 輸 入 電壓僅 限 200- 240V
3262187600
WARNING
ISOLATE MAINS BEFORE REMOVING COVER
注意 打開前先切斷主電源
注意 打开前先切断主�源
Note
注意 注意
: Input voltag e limited 200 -240V
: 输 入 电 压仅 限 200 -240 V : 輸 入 電壓僅 限 200- 240V
3262187600
3262187600
WARNING
ISOLATE MAINS BEFORE REMOVING COVER
注意 打開前先切斷主電源
注意 打开前先切断主�源
Size: 67*50mm
堆疊機台前請先按箭 頭指示方向取下上面 機台的四個腳座
堆叠机台前请先按箭 头指示方向取下上面 机台的四个脚座
3262903300
Follow the arrow direction to remove the four feet of the upper machine before stacking.
Size: 110*96mm
You can use eyebolts temporarily when lifting one projector.
Caution:
Eyebolts should only be used for one projectorEyebolts can't use for fix the projector for long time.A single line is required for one eyebolt
可暫時使用投影機上的吊環來將投影機吊至高處
警告
使用吊環吊掛投影機時, 僅適用於吊掛
單台投影機
不可長時間使用吊環或是使用吊環來
固定投影機於天花板上
吊掛時, 每個吊環請使用單獨的一條線
材
可暂时使用投影机上的吊环来 将投影机吊至高处
警告
使用吊环吊挂投影机时, 仅适
用于吊挂单台投影机
不可长时间使用吊环或是使用
吊环来固定投影机于天花板上
吊挂时, 每个吊环请使用单独
的一条线材
320XXXXXXX
Page 8
Rev A January 2019
Page 8
Important Information
Label locations
1
Location of Manufacturer’s ID
Label with Product Identication, Serial Number, Certication
Statement and Risk Statement on the body of the projector
2
Location of Maintenance Warning Label
3
Location of Mains Information Label
Location of Hazard Warning Symbol and Aperture Label on the body of the projector
Protective Housing Label (under
the top cover and only visible to service personnel)
3262187600
WARNING
ISO
LATE MAINS BEFORE REMOVING CO
VER
注意
打開前先切斷主電源
注意
打开前先切断主�源
2
Note
注意 注意
: Input voltage limited 200-240 V
:输入电 压 仅限 200-240V
:
輸入電壓僅限
200-240V
3262187600
WARNING
ISOLATE MAINS BEFORE REMOVING COVER
注意 打開前先切斷主電源
注意 打开前先切断主�源
3
1
Made in China Fabriqué en Chine
中国制造 中國製造
Greenside Way, Middleton Manchester, UK, M24 1XX
英国 曼彻斯特 格林赛得路
英國 曼徹斯特 格林賽得路
Name of Product : DLP Projector Nom du produit: DLP Projecteur
产品名称:数字投影机 產品名稱:數位投影機
Di
gital Projection Limited
英国缔佳有限公司 英國締佳有限公司
Laser Radiation Avoid direct eye exposure Class 3R Laser product Wave length : 450-460nm Max output : 330mW
Risk Group 3 Warning! Do not look into the beam. No direct eye exposure to the beam is permitted. RG3 IEC EN 62471-5:2015 Hazard Distance : Refer to Manual
Groupe de Risque 3 Attention! Ne pas regarder dans le faisceau. Pas d'exposition directe des yeux au faisceau est autorisée. RG3 IEC EN 62471-5:2015 Distance de danger : Se reporter au manuel
警 告：此为A 级产品，在生活环境中，该产品可能会造成无线电干扰
。
在这种情况下
，
可能需要用户对干扰采取切实可行的措施
。
警告使用者：這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾
，
在這種
情況下，使用者會被要求採取某些適當的對策。
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser notice No.50, Dated June 24, 2007 Class 1 Laser Product IEC/EN 60825-1:2014
Rayonnement Laser Èvitez d’exposer directement les yeux Produit Laser de classe 3R Longueur d’onde : 450-460nm Sortie maximale : 330mW IEC/EN 60825-1:2007 IEC/EN 62471-1:2006 Produit laser de classe 1 IEC / EN 60825-1: 2014
激光辐射 请勿直视光束 3R类激光产品 波长: 450-460nm 最大输出: 330mW IEC 60825-1:2007 / GB 7247.1-2012 第一类激光产品 IEC / EN 60825-1: 2014
雷射輻射 請勿直視光線 3R級雷射產品 波長：450-460nm 最大輸出: 330mW IEC/ EN
60825-1:2007 IEC/ EN 62471-1:2006 第一類雷射產品 IEC/ EN 60825-1:2014
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference. (2) This device must accept any interference recieved, including interference that may cause undesired operation.
WARNING ATTENTION
注意/注意
Isolate mains before removing cover. Isolez les conduites avant d'enlever le couvercle.
打开前先切断主电源/打開前先切斷主電源
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet équipement à la pluie ou à l'humidité.
�勿�投影机置于雨中或潮��境中以降低起火或电�风险.
請勿將投影機放在雨中或潮濕環境中以降低起火或電擊的風險.
200-240VAC 50/60Hz 17A
(Not for China / 非中國使用 / 非中国使用)
Model / Modèle
型号/型號
Pa
rt No. / Numéro de pièce
零部件号/零部件號
Serial No. / Numéro de série.
序号/序號
Po
wer / Puissance
电源/電源
电源 : 200-230VAC 50/60Hz 17A
Only for China/僅限中國/仅限中国
CAN ICES-3(A)/NMB-3(A)
デルタ電子株式会社
Titan User Guides
Follow link for Projector Documentation
この二次元バーコードをスキャンしてプロジェクターのデータを取得してください
请扫描条码来取得投影机的文件
프로젝터 설명서를 보려면 링크를 팔로우하십시오
Suivre le lien pour accéder à la documentation du projecteur Produktdokumentation nden Sie unter dem Link
WJ XXXX
3264652800
Fill in manufacture plant code, such as WJ, TW
Fill in Vendor’s code
Such as: CM, GG, FS....etc.
IEC/EN 60825-1:2007 IEC/EN 62471-1:2006
Not for household use
4
5
3524167100
PML DP
MLUF-33R DA CW
2018.03.05
2018.03.052018.03.05
THIRD ANGLE
PROJECTION
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
Part No.
Description:
Drawn:
Sheena.Ho
何 素 真
Design:
Sheena.Ho
何 素 真
REV.
ISSUE DATE:
00
SHEET OF
3 3
UNITSCALE USED ON
HOLES : ±0.05 ANGLES : ±0.5°
( )
150~200
200~250
UP~100
100~150
: ±0.2
: ±0.1
X.X
X.XX
: ±0.3
DECIMALS
( )
X
: ±0.3
: ±0.35
: ±0.25
5.1± :2.0± :
: ±2.4
: ±3.1
: ±0.45
350~400 : ±0.5
300~350
250~300 : ±0.4
900~OVER
( )
UP~600
600~900
Caution : Air vents - Do not block
注意：通风口——请勿堵塞 注意：通風口——請勿堵塞
119-725
309045160X - USA
XX Kg
119-704
309045500X - EUR
XX Kg
119-726
309045160X - USA
XX Kg
119-705
309045500X - EUR
XX Kg
119-728
309046070X - CN
XX Kg
119-727
309046070X - CN
XX Kg
Power Cord(D)
LASER APERTURE
LASER ÖFFNUNG
OUVERTURE LASER
АΠЕРΤУРAЛАЗЕРA
レーザ 開口
레이저 개구부
激光辐射之孔径
雷射輻射之孔徑
4
5
Page 9
Digital Projection Titan Laser Series
Rev A January 2019
Page 9
Important Information
Location of laser aperture
The laser aperture 1 is located as indicated below.
Interlock switches
Interlock switches installed at the main frame, inside the cover, will power-o󰀨 the system individually when activated.
1
Will be activated when the top cover is removed.
2
Will be activated when the projection lens is removed.
1
1
2
Page 10
Rev A January 2019
Page 10
Important Information
General precautions
The unit is never to be operated if the unit is defective or the cover or seal is damaged.
No maintenance allowed by end user.
Do not open the cabinet. There are no user serviceable parts inside.
No service is allowed except by authorized personnel.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equipment MUST be
earthed.
Take care to prevent small objects such as paper or wire from falling into the projector.
If this does happen, switch o󰀨 immediately, and have the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any liquids on top of
the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power
cable.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could cause a re
Always allow the projector to cool for 5 minutes before disconnecting the power or
moving the projector.
Never use strong detergents or solvents such as alcohol or thinners to clean the
projector and lens.
Do not use the carry handles to mount or hang the projector.
Page 11
Digital Projection Titan Laser Series
Rev A January 2019
Page 11
Important Information
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar connectors
may have a dangerously high voltage source.
The projector must be installed only by suitably qualied personnel, in accordance with
local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in an
emergency.
Ensure that there is at least 50cm (19.7in) of space between the ventilation outlets and
any wall, and 30cm (11.8in) on all other sides.
Do not install the projector close to anything that might be a󰀨ected by its operational
heat, for instance, polystyrene ceiling tiles, curtains etc.
Place the projector in a dry area away from sources of dust, moisture, steam, smoke,
sunlight or heat.
The projector is heavy. Use safe handling techniques when lifting the projector.
Do not drop or knock the projector.
Before installation, make sure that the surface, ceiling or rigging that is to support the
projector is capable of supporting the combined weight of the projector and lens.
When stacking projectors, the stack MUST be vertical, to ensure that the stresses are
distributed to all four chassis corners.
Do not stack more than 2 projectors.
Do not place heavy objects on top of the projector chassis. Only the chassis corners
and the optional rigging frame are capable of withstanding the weight of another projector.
Backup safety chains or wires should always be used with ceiling mount installations.
The projector can be operated any position, as shown in the diagram:
FDA regulations require that a lens Hood is permanently tted when using the 4.16-
6.96:1 lens with the Titan Laser range of projectors in the United States of America.
Fitting can be provided by your reseller or System Integrator.
360°
Pitch
360°
Roll
Page 12
Rev A January 2019
Page 12
Important Information
When using projectors in environments with third party high power laser systems avoid
direct laser beams pointing towards the projection lens. This may cause incident light
to converge into the optical engine and cause damage to the DLP DMD.
Please pay attention to projector installation with respect to other staging laser light
equipment set-up. These systems can cause permanent damage to the DMD imaging
devices used in our projectors. This damage is not covered by our warranty.
Make sure the lens cap is removed from the rear of the lens before it is inserted into the
projector.
Make sure the lens caps are removed from the lens before operating the projector. Light
energy levels this have been known to cause damage to both the lens and projector optics. This damage is not covered by our warranty.
Light hazard warning
Failure to comply with the following may result in serious injury:
• No direct exposure to the beam is permitted, RG3 IEC 62471-5:2015.
• Operators control access to the beam within the hazard distance or install the
projector at su󰀩cient height to prevent exposures of spectators’ eyes within the
hazard distance.
The hazard distance (Fig. 1) is the distance measured from the projection lens at which the intensity or energy per unit of surface is lower than the applicable exposure limit on the cornea or skin. If the person is within the hazard distance, the beam is considered unsafe for exposure.
Light hazard distances
Lens Hazard Distance
0.67: 1
1.12 : 1
1.16-1.49:1 5.5m
1.39-1.87:1 6.5m
1.87-2.56:1 8.5m
2.56-4.16:1 10.5m
4.16-6.96:1 14m
6.92 - 10.36:1
Do not use the 0.67:1 and 1.12:1 xed throw lenses with the 4K-UHD projectors
Fig. 1: hazard distance
Page 13
Digital Projection Titan Laser Series
Rev A January 2019
Page 13
Important Information
Operation and conguration precautions
Do not make changes to the networking conguration unless you understand what you
are doing, or have taken advice from your Network Manager. If you make a mistake,
it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original
settings, and any changes you have made.
Software update should NOT be carried out except by, or with the supervision of, Digital
Projection Service personnel.
Compliance with international standards
RF Interference
FCC
TheFederalCommunicationsCommissiondoesnotallowanymodicationsorchangestotheunit EXCEPTthosespeciedbyDigitalProjectioninthismanual.Failuretocomplywiththisgovernment
regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference.
Noise
GSGV Acoustic Noise Information Ordinance
The maximum sound pressure level is 52 dB (A) according to ISO 3744 or ISO 7779.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic Equipment. Our products are designed with reuse, recycling and recovery of all components in mind. To this end, at end of life, your projector may be returned to Digital Projection Ltd or its agent so that the environmental impact can be minimised.
Page 14
Rev A January 2019
Page 14
Important Information
Whats in the Box?
Projector
Remote control
PicMute
OPEN
CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
A B C D
USERPRESET
2x AAA batteries
Important Information HDMI cable Remote cable
Power Cable UK/ROW Power Cable USA
Page 15
Digital Projection Titan Laser Series
Rev A January 2019
Page 15
Important Information
Basic Operation Instructions
Positioning the screen and projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mounttheprojector,ensuringthatitisatasuitabledistancefromthescreenfortheimagetoll the screen. Set the adjustable feet so that the projector is level, and perpendicular to the screen.
Thedrawingbelowshowsthepositionsofthefeetfortablemounting,andthexingholestomount
the projector in inverted ceiling installations.
1
Four adjustable feet
2
Four M10 holes for ceiling mount
The screws should not penetrate more than 30 mm into the body of the projector.
Do not use the threaded holes for the adjustable feet to hang or mount the projector.
1
2
1
1
1
2
2
2
Page 16
Rev A January 2019
Page 16
Important Information
Stacking and rigging
The top of the projector has pins and the bottom of the projector has cups. The pins and cups can connect together and be locked into place with a locking pin.
This system should only be used to stack a
maximum two projectors.
1. Remove the adjustable feet from the projector that will be stacked on the top.
1
2. Mount the projector on top of the other projector. Ensure that all four cups are placed over the pins on the bottom projector.
2
3. Push the locking pins into place on each cup and pin.
3
Amoutingrailmayalsobettedusingthepinandcup
system. This is an optional accessory to the projector. It can be used with commercially available rigging truss clamps to attach the projector to a staging or lighting truss.
Only qualied riggers should make this installation after careful consideration of the strength and safety of the truss.
2
1
3
Page 17
Digital Projection Titan Laser Series
Rev A January 2019
Page 17
Important Information
Foureye-boltsarettedtothetopoftheprojectortoenabletheyingoftheprojectorusingsteelwire
or chains.
This system should only be used to y a single projector. Do not stack projectors and y them together.
Point-to point connections
Refer to the following guidelines when connecting one end of a suspension cable directly to an eye­bolt and the other to a suspension point.
• The suspension cables can be connected to the eye-bolts
at an angle of up to 45° around the eye ring.
• The suspension cables must not be connected to the
eye-bolts at any angle across the eye ring.
• The suspension cable must run vertically up from the
projector.
Examples of correct
congurations:
Exampleofanincorrectconguration
1
2
1
2
45° 45°
Page 18
Rev A January 2019
Page 18
Important Information
Threaded suspension cables
Refer to the following guidelines when threading the suspension cable through the eye-bolts and connecting both ends to suspension points.
• The suspension cable can exit the eye-bolts at an
angle of up to 45° around the eye ring.
• The suspension cable can exit the eye-bolts at an
angle of up to 45° across the eye ring.
• The suspension cable should not be threaded
through 2 or more eye-bolts
Examplecongurations:
Do not use the carry handles to mount or hang the projector.
1
1
2
2
45°45°
45° 45°
Page 19
Digital Projection Titan Laser Series
Rev A January 2019
Page 19
Important Information
Inserting a new lens
Before changing the lens, always make sure the projector is switched o󰀨 and fully
disconnected from its power supply.
Always allow the projector to cool for ve minutes before disconnecting the power or
moving the projector.
The lens release lever should always be set to the locked position to prevent the lens
from falling out.
Do not place the projector with its front panel down on a surface, as this may damage
the lens or the lens release lever.
Avoid touching the surface of the lens as this may result in image impairment.
Take care to preserve the original lens packaging and protective caps for future use.
1. Turn the lens release lever
clockwise so that it is pointing upwards, to open the lock fully.
1
2. Remove the rear lens cap from
the lens.
3. Insert the lens into the lens
aperture, making sure that the plug on the zoom drive mechanism lines up with the socket on the front of the projector, then push the lens in
rmlyasfarasitwillgo.
2
4. Turn the lens release lever anti-
clockwise to the mid-position.
3
3
1 2
Page 20
Rev A January 2019
Page 20
Important Information
5. Thelenscannowbepushedinfurther.Pushthelensinrmlyasfarasitwillgo.
6. Turn the lens release lever
fully anti-clockwise so that it is pointing downwards, to close the
lock fully.
4
Removing the lens
To remove the lens, reverse the procedure described in Inserting a new lens above:
1. Turn the release lever up to the mid-position, then pull the lens out as far as it will go.
2. Turn the release lever clockwise so it is pointing upwards, then pull the lens out completely.
Fitting a lens hood
FDA regulations requires that a lens Hood is permanently tted when using the 4.16-6.96:1 lens with the Titan Laser range of projectors in the United States of America. Fitting can be provided by your reseller or System Integrator.
1. Remove the six screws.
1
2. Remove the lens glass
4
1
Page 21
Digital Projection Titan Laser Series
Rev A January 2019
Page 21
Important Information
3. Place hood over the lens, aligned with the screw holes.
4. Screw in the six screws to secure the hood.
2
5. Pace the six sponges over the locating pins on the hood.
3
6. Place the glass and bracket over the hood.
7. Screw in the six screws to secure the glass and bracket
to the hood.
4
2
3
4
Page 22
Rev A January 2019
Page 22
Important Information
Connecting the power supply
Rest of the world:
Firmly push the mains connector into the socket.
USA only:
Firmly push the mains connector into the socket.
Rotate the connector 90° clockwise to lock it in place
Use only the power cable provided.
Ensure that the power outlet includes a ground connection as this equipment MUST be
earthed.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power
cable.
1
2
2
1
Page 23
Digital Projection Titan Laser Series
Rev A January 2019
Page 23
Important Information
Switching the projector on
1. Connect the power cable between the mains supply and the projector. (See Connecting the
power supply above.) Switch the breaker switch next to the power connector to on.
The POWER indicator turns red to signal that the projecter is on and in STANDBY mode.
2. Press one of the following buttons:
• On the remote control, the ON button
• On the projector control panel, the POWER button.
The POWERindicatorbeginsashinggreenastheprojectorpowersup.Whentheashingstops, the POWER indicator lights solid green and the Digital Projection logo appears on the screen. The projector is switched on and projecting.
Switching the projector o󰀨
1. Press OFF on the remote control or POWERonthecontrolpanel,thenpressagaintoconrm
your choice.
The POWERindicatoronthecontrolpanelwillstartashingblue,theprojectedimagewillturno󰀨 and the cooling fans will run for a short time until the POWER indicator goes steady red to indicate that the projector has entered STANDBY mode.
2. Ifyouneedtoswitchtheprojectoro󰀨completely,switchthebreakerswitchnexttothepower
connectortoo󰀨andthendisconnectthepowercablefromtheprojector.
Page 24
Rev A January 2019
Page 24
Important Information
Selecting an input signal
1. Connect one or more image sources to the projector.
2. Select the input you want to display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the
main menu, press ENTER/OK and then select an input signal using the UP and DOWN arrow buttons. Press ENTER/OKtoconrmyourchoice.
Selecting a test pattern
To display a test pattern:
• Press TEST on the remote control. If necessary, press again to change the test pattern. Test
patterns are displayed in the following order:
O, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst, H Burst, ColorBar, Pluge
Afterthenaltestpattern,theprojectorexitstestpatternmodeandreturnstothemainimage.To
view test patterns again, you need to press TEST again.
• Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu,
then select a test pattern using the LEFT and RIGHT arrow buttons.
Page 25
Digital Projection Titan Laser Series
Rev A January 2019
Page 25
Important Information
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. The setting
operates in Zoom/Focus Adjustment and Shift Adjustment mode.
Press ENTER/SELECT to switch between the two modes.
Remote control
Use the remote control to adjust zoom, focus and shift directly, without opening a menu:
• OK enters lens control, then switches between Zoom/Focus Adjustment and Shift Adjustment.
• EXIT exits lens control and opens the Lens menu.
• MENU exits lens control and returns to the main image.
• The arrow buttons adjust zoom, focus and shift as indicated on the screen.
Adjusting the image
Orientation
• This can be set from the Setup menu.
Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop and Rear
Ceiling.
Keystone
• This can be set from the Geometry menu.
Picture
• Settings such as Gamma, Brightness, Contrast, Saturation, Hue and Sharpness can be set
from the Image menu
Page 26
Rev A January 2019
Page 26
Important Information
Control Panel Reference
1
POWER
Switchestheprojectoronando󰀨(STANDBY).
Indicator:
O󰀨=theprojectorisswitchedo󰀨 Flashinggreen=theprojectoriswarmingup Flashingblue=theprojectoriscoolingdown On,red=STANDBYmode On,green=theprojectorisswitchedon
2
INPUT
Switches to the next input source.
3
AUTO SYNC
Re-synchronises with the current input signal.
4
ASPECT
Changes the aspect ratio.
5
CENTER LENS
Centers the lens.
6
PIC MUTE
Switchesthelasero󰀨/on.
Indicator:
O󰀨=theprojectorisinstandby On,blue=theprojectorison,normalprojection On,red=theprojectorison,picturemuteisactivated
1 2 3 4 5 6
11 12 13 14 15 16
7 8 9
10
Page 27
Digital Projection Titan Laser Series
Rev A January 2019
Page 27
Important Information
7
LIGHT INDICATOR
O󰀨=lightisswitchedo󰀨 Flashingred(cyclesofsingleashes)=failuretolightupduringpowerup Flashingred(cyclesofdoubleashes)=failuretolightup On,green=lightisswitchedon
8
TEMP INDICATOR
O󰀨=noproblem Flashingred=temperatureerror
9
HOTKEYS
User selectable functions. Pre-set functions: HOTKEY 1 Information HOTKEY 2 Test Pattern HOTKEY 3 Lens Memory Load Additional options: Picture Mode Ambient Brightness Correction Freeze PIP Swap
10
STATUS
O󰀨=noproblem Flashingred(continuously)=covererror Flashingred(cyclesoffourashes)=fanerror On,red=systemerror
11
MENU
Displays and exits the OSD.
12
Arrow buttons & ENTER
Navigation buttons used to highlight menu entries in the OSD. Press ENTER to open or execute the highlighted menu entry.
13
EXIT
Exits the current OSD page and enters the level above.
14
LENS SHIFT arrow buttons
Eachofthesebuttonsmovesthelensinthespecieddirection.
15
FOCUS plus and minus buttons
Used to move the focus in and out.
16
ZOOM plus and minus buttons
Used to zoom in and out.
Page 28
Rev A January 2019
Page 28
Important Information
Remote Control Reference
1
Power ON/OFF
Turnstheprojectoronando󰀨. Toturntheprojectoro󰀨,pressthe OFFbuttontwicewithinveseconds.
2
Pic Mute OPEN / CLOSE
Shows and hides the projected image.
3
OSD ON / OFF
Enables and disables screen timeout messages and showing the OSD during projection.
4
MENU
Access the projector OSD (on-screen display). If the OSD is open, press this button to go back to the previous menu.
5
Navigation (arrows and OK)
Navigate through the menus with the arrows,conrmyourchoicewithOK. In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11 below. In lens adjustment modes, or when the OSD is not showing, the OK button switches between modes:
Shift Adjustment and Zoom / Focus Adjustment.
6
EXIT
Close the current OSD page and return to the level above.
7
FREEZE
Freeze the current frame.
8
DEFAULT
Restore default settings.
9
INFO
Access information about the projector.
10
RE-SYNC
Re-synchronise with the current input signal.
Pic Mute
OPEN
CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
A B C D
USER PRESET
1
2
5
6
8
4
9
7
3
10
Page 29
Digital Projection Titan Laser Series
Rev A January 2019
Page 29
Important Information
11
LENS adjustment
FOCUS IN / OUT: adjust focus. SHIFT: press and hold this button,
then use the Navigation arrow buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12
USER PRESET A, B, C, D
Load user presets.
13
ALT
Press and hold this button to access alternative functions for all buttons with a green label.
14
DVI / DisplayPort2 / numeric
input 3
There is no DVI input on this projector. There is no DisplayPort2 input on this projector
15
HDMI 2 / HDMI 4 / numeric input
2
Select the HDMI 1 input. Use with ALT to switch to the HDMI 4 input.
16
HDMI 1 / HDMI 3 / numeric input
1
Select the HDMI 1 input. Use with ALT to switch to the HDMI 3 input.
17
TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern: ...Off, White, Black, Red,
Green, Blue, Checkerboard, CrossHatch, V Burst, H Burst, ColorBar, Pluge...
Use with ALT to SWAP the Main and PIP displays.
Pic Mute
OPEN
CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
A B C D
USER PRESET
13
11
12
14
15
16
17
Page 30
Rev A January 2019
Page 30
Important Information
18
DisplayPort 1 / R / numeric input 4
Select the DisplayPort 1 input. Use with ALT to toggle the Red
channelonando󰀨
19
HD-T / G / numeric input 5
Select the HDBaseT input. Use with ALT to toggle the Green
channelonando󰀨
20
SDI / B / numeric input 6
Select the 3G-SDI input. Use with ALT to toggle the Blue
channelonando󰀨
21
VGA / 3D / numeric input 7
Select the VGA input. Use with ALT to toggle the 3D
FormatsettingbetweenO󰀨and
Auto.
22
COMP1 / EYE / numeric input 8
There is no Component 1 input on this projector Use with ALT to switch between left and right eye 3D dominance.
23
COMP2 / PIP / numeric input 9
There is no Componenet 2 input on this projector Use with ALT to toggle the PIP
windowonando󰀨.
24
ADDR / ALL
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until
theindicatorstartsashing.
2. Release this button and while
theindicatorisstillashing,
enter a two-digit address using the numeric input buttons. The
indicatorwillashthreetimes quicklytoconrmthechange.
To unassign an address and
return to the default address 00,
• Press and hold ALT and this
button simultaneously until the
indicatorashestoconrmthe
change.
Pic Mute
OPEN
CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
A B C D
USER PRESET
24
19
20
18
21
22
23
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use