Large screen video projector type The CE mark was rst applied in:
M-Vision Cine LED December 2009
Basis on which Conformity is being declared
The products identied above comply with the protection requirements of the above EU directives, and the
manufacturer has applied the following standards.
EN 55022:1998 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Information
Technology Equipment.
EN 55024:1998 - Limits and Methods of Measurement of Immunity Characteristics of Information Technology
Equipment.
EN 60950-1:2001 - Specication for Safety of Information Technology Equipment, including Electrical Business
equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage
directive has been compiled by the signatory below and is available for inspection by the relevant enforcement
authorities.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 1 December 2009
Attention!
The attention of the specier, purchaser, installer, or user is drawn to special measures and limitations to use which
must be observed when these products are taken into service to maintain compliance with the above directives.
Details of these special measures are available on request, and are also contained in the product manuals.
Digital Projection M-Vision Cine LEDUser Manual
Important Information
Please read this user manual carefully before using the projector, and keep
the manual handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in this guide
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of
electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical
injury to yourself and/or damage to the equipment unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that
you should read.
Trademarks
• IBM is a registered trademark of International Business Machines Corporation.
• Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.
• Other product and company names mentioned in this user’s manual may be the
trademarks of their respective holders.
Product revision
• Because we at Digital Projection continually strive to improve our products, we
may change specications and designs, and add new features without prior
notice. Projectors built prior to this revision of the User Manual may therefore not
include all the features described.
Manual revision
DateDescriptionRevision
September 2010Rev A
December 2010correction to switch on sequence in section
4, Trigger output in sections 2 and 4, extra
connection examples
Rev B
Rev E October 2014 Page v
Important Information Digital Projection M-Vision Cine LEDUser Manual
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this
equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling
into the projector. If this does happen, switch off immediately, and have
the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any
liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a
damaged power cable.
The LED module in this projector should be changed ONLY by
authorised and qualied service personnel.
Notes
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could
cause a re
Never use strong detergents or solvents such as alcohol or thinners to
clean the projector and lens.
Page vi Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual Important Information
Installation precautions
The projector must be installed only by suitably qualied personnel, in
accordance with local building codes.
The projector should be installed as close to the power outlet as
possible.
The power connection should be easily accessible, so that it can be
disconnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the
ventilation outlets and any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by
its operational heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 15 kg (33 lbs). Use safe handling
techniques when lifting the projector.
Do not stack more than three projectors.
When stacking projectors, the stack MUST be vertical, to ensure that
the stresses are distributed to all four chassis corners.
Before installation, make sure that the surface, ceiling or rigging that is
to support the projector is capable of supporting the combined weight
of all the projectors.
Notes
Backup safety chains or wires should always be used with ceiling
mount installations.
Do not place heavy objects on top of the projector chassis. Only the
chassis corners are capable of withstanding the weight of another
projector.
Do not drop or knock the projector.
Place the projector in a dry area away from sources of dust, moisture,
steam, smoke, sunlight or heat.
Operation and conguration precautions
Software update should NOT be carried out except by, or with the
supervision of, Digital Projection Service personnel.
Rev E October 2014 Page vii
Important Information Digital Projection M-Vision Cine LEDUser Manual
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 32 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modications or
changes to the unit EXCEPT those specied by Digital Projection in this manual.
Failure to comply with this government regulation could void your right to operate
this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant with Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
European Waste Electrical and Electronic Equipment
(WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and
Electronic Equipment. Our products are designed with reuse, recycling
and recovery of all components in mind. To this end, at end of life, your
projector may be returned to Digital Projection Ltd or its agent so that the
environmental impact can be minimised.
Notes
Page viii Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual Important Information
Digital Projection Contact details
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Ofce: as above
Operation and conguration precautions ......................................................................................vii
Compliance with international standards ...................................................................................... viii
Noise ................................................................................................................................................ viii
RF Interference.................................................................................................................................. viii
European Waste Electrical and Electronic Equipment (WEEE) Directive ................................................. viii
Digital Projection Contact details ......................................................................................................ix
1. Introduction
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front view ........................................................................................................................................ 1.4
Aspect ratio ...................................................................................................................................... 2.2
Positioning the screen and projector ................................................................................................... 2.6
Screen size vs throw distance ............................................................................................................ 2.7
Shifting the image............................................................................................................................. 2.10
Mounting the projector .....................................................................................................................2.11
Test pattern ...................................................................................................................................... 3.3
Adjusting the lens............................................................................................................................... 3.3
Adjusting the projected image ........................................................................................................ 3.4
Aspect ratio ...................................................................................................................................... 3.4
Using the control keys ...................................................................................................................... 4.6
Power .............................................................................................................................................. 4.6
Aspect ratio ...................................................................................................................................... 4.6
User memory .................................................................................................................................... 4.6
Test pattern ...................................................................................................................................... 4.7
Using the menus ................................................................................................................................. 4.8
Navigating menus and submenus ....................................................................................................... 4.8
continued
Page xii Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual Table of Contents
Main menu ............................................................................................................................................ 4.9
Aspect Ratio ..................................................................................................................................... 4.9
Logo Display .................................................................................................................................. 4.23
Control menu ..................................................................................................................................... 4.24
Auto Source ................................................................................................................................... 4.25
Keys 1 to 5 ..................................................................................................................................... 4.25
Service menu ..................................................................................................................................... 4.26
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front view ........................................................................................................................................ 1.4
1. Introduction Digital Projection M-Vision Cine LEDUser Manual
What’s in the box?
• Make sure your box contains everything listed. If any pieces are missing, contact
your dealer.
• You should save the original box and packing materials, in case you ever need
to ship your Projector.
Projector
(0.73:1 xed lens 110-001
1.56–1.86:1 zoom lens 110-002
1.85–2.40:1 zoom lens 110-003)
Notes
For more detailed information
about lenses, see Screen size
vs throw distance, in section
2. Installation.
Only one power cable -
dependent on the destination
territory - will be supplied with
the projector.
Power cable 10A
Europe
(102-163)
Remote control
(109-685)
2x AA batteries
Power cable 13A
North America
(102-165)
User Manual on disc
(115-759)
Power cable 10A
United Kingdom
(102-180)
Important Information
(110-287)
HDMI cable
Getting Started Guide
(111-185)
5mm Allen
wrench
Page 1.2Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual 1. Introduction
Key features of the projector
Congratulations on your purchase of the Digital Projection M-Vision Cine LED
projector.
The imagery benets associated with the M-Vision are plentiful, including an
expanded colour gamut range and accelerated contrast performance. Augmenting
these benets is the over 60,000 hour lamp life, courtesy of solid state illumination
technology, which guarantees a long and low-maintenance display life.
Installation is incredibly exible due to the M-Vision’s compact and lightweight
chassis design, and extraordinary lens shift range of .15 of frame horizontal and .6
of frame vertical. Multiple lens options provide further exibility, with a throw range
from .73 to 2.40:1. Connectivity includes two HDMI inputs, as well as RGB via D-15,
component, composite and S-Video inputs.
Providing 3-chip colour saturation from a small-form single-chip display, the MVision Cine LED presents a powerful yet remarkably affordable solution for a variety
of commercial and home entertainment applications where image quality and
long-life usage are equally important. In any environment where ambient light can
be controlled, the M-Vision Cine LED represents the perfect low maintenance home
theater projector in limited ambient light.
As is the case with all Digital Projection displays, our advanced engineering
guarantees the M-Vision Cine LED provides remarkable contrast and color
saturation for years to come. Equally important, our legacy in superior customer
and technical services assures our experienced support staff is always available to
address your needs.
Notes
Key Features
• High resolution projector for low ambient light venues
• Applications: Command and Control, Simulation, Home Cinema, Fixed Install
and Rental
• Brightness 1000 ANSI lumens ±10%
• Contrast 10,000:1 ±10%
• 1920 x 1080 resolution
• Precision mechanical design ensuring maximum amount of light from LED
module reaches optics, without any operator adjustment
• 230-280W single phase, 100-240VAC ±10%
• Compact size, light weight - approximately 15 kg (33 lbs)
• Robust metal case
• RS232 connection for remote operation using control codes
• Seven selectable Digital and Analogue Video inputs for display of the latest as
well as legacy video standards.
HDMI, RGBHV, Component, S-Video, Composite all as standard
• IR remote control for easy setup
Rev E October 2014 Page 1.3
1. Introduction Digital Projection M-Vision Cine LEDUser Manual
Vertical shift
adjustment
Getting to know the projector
Front view
Zoom
ring
Focus
ring
Front Infra-red
window
(remote control)
Lens
Horizontal shift
adjustment
Notes
(adjustments
under badge)
For more detailed information
about lenses or lens shift, see
section 2. Installation
Air inlet
Air inlet
Rear view
Air
inlets
Projector
control
panel
Adjustable feet
For information about how to
change the LED module, see
section 5. Maintenance.
Aspect ratio ...................................................................................................................................... 2.2
Fitting the image to the DMD ............................................................................................................. 2.2
Examples of 16:9 images displayed with different aspect ratio settings ........................................................ 2.2
Examples of 4:3 images displayed with different aspect ratio settings ......................................................... 2.3
Examples of 2.35:1 images displayed with different aspect ratio settings ..................................................... 2.3
Power connection ........................................................................................................................... 2.16
Rev E October 2014 Page 2.1
2. Installation Digital Projection M-Vision Cine LEDUser Manual
Screen requirements
Aspect ratio
Fitting the image to the DMD
The projector uses a DMD (Digital Mirror Device) to create the image that is
projected onto the screen. The resolution of the DMD in this projector is 1920 x
1080 pixels, or to put it another way, its aspect ratio is 16:9.
1920 pixels
1080 pixels
16 units
If the source image supplied to the projector has a different aspect ratio from this,
or even if it has the same aspect ratio but fewer pixels, then the image will not ll
the DMD. The projector therefore needs to scale the image.
9 units
Notes
The projector has ve aspect ratio settings, so that you can choose the one that is
most suitable for your image source. The settings are:
16:9 the image is scaled to ll the DMD (and thus, a 16:9 screen).
Theaterscope the image is scaled such that a 2.35:1 image will be displayed
at the correct aspect ratio when the projector is tted with an
anamorphic lens. Thus an image with an aspect ratio of 2.35:1
can be displayed using the full 16:9 resolution of the DMD.
4:3 the image is scaled to t a 4:3 screen, using the full height of the
DMD.
4:3 Narrowto be used for 4:3 images in combination with an anamorphic
lens. The image is scaled to t the DMD vertically, but squeezed
horizontally such that the lens will stretch it to the correct ratio.
Nativethe image is displayed with no scaling, at its original resolution, in
the centre of the screen.
Examples of 16:9 images displayed with different aspect ratio settings
For more information about
changing the Aspect ratio
setting, see Using the control
keys and Using the menus
in section 4. Controlling the
Projector.
The 16:9 image shown here has
far fewer pixels than the 1920 x
1080 of the DMD. Your image
may be different.
16:9
Note that, as the aspect ratio of the image matches that of the DMD, the 16:9
setting is best, unless there is some specic reason for wanting the smaller image,
for instance, to maintain the same scale as other images from the same source.
Native
Page 2.2Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual 2. Installation
Examples of 4:3 images displayed with different aspect ratio settings
4:3
The 4:3 setting is best, unless there is some specic reason for wanting the smaller
Native image, for instance, to maintain the same scale as other images from the
same source.
If you are using an anamorphic lens, the 4:3 Narrow setting should be used. The
lens will stretch the image to the correct width.
4:3 Narrow
without anamorphic lens
Native
4:3 Narrow
with anamorphic lens
Notes
The 4:3 image shown here has
far fewer pixels than the 1920 x
1080 of the DMD. Your image
may be different.
If you are using an anamorphic
lens, you will need to use the
4:3 Narrow setting to correct the
image.
Examples of 2.35:1 images displayed with different aspect ratio
settings
16:9Native
The 16:9 setting is best, unless there is some specic reason for wanting the
smaller Native image, for instance, to maintain the same scale as other images from
the same source.
If you have an anamorphic lens, the Theaterscope setting would be a much better
option. Because it uses the whole of the DMD, it will be a much brighter image than
the letterboxed options shown above, and will ll a wider screen if this is available.
Theaterscope
without Anamorphic lens
with Anamorphic lens,
stretched to ll wider screen
The 2.35 image shown here has
far fewer pixels than the 1920 x
1080 of the DMD. Your image
may be different.
To take advantage of the
Theaterscope setting, you
MUST have an anamorphic
lens.
Rev E October 2014 Page 2.3
2. Installation Digital Projection M-Vision Cine LEDUser Manual
Diagonal screen sizes
Screen sizes are sometimes specied by their diagonal size (D) in inches. When
dealing with large screens and projection distances at different aspect ratios, it is
more convenient to measure screen width (W) and height (H).
W = width
H = height
D = diagonal (inches)
The example calculations below show how to convert diagonal sizes in inches into
width and height, at various aspect ratios.
2.35:1 (Scope)
W = D x 0.92in (D x .023m) H = D x 0.39in (D x .01m)
1.85:1
W = D x 0.88in (D x .022m) H = D x 0.47in (D x .012m)
16:9 = 1.78:1 (native aspect ratio)
W = D x 0.87in (D x .022m) H = D x 0.49in (D x .0125m)
Notes
1.66:1 (Vista)
W = D x 0.86in (D x .022m) H = D x 0.52in (D x .013m)
16:10 = 1.6:1
W = D x 0.85in (D x .022m) H = D x 0.53in (D x .014m)
4:3 = 1.33:1
W = D x 0.8in (D x .02m) H = D x 0.6in (D x .015m)
Page 2.4 Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual 2. Installation
Fitting the image to the screen
It is important that your screen is of sufcient height and width to display images at
all the aspect ratios you are planning to use.
Use the conversion chart, or the sample calculations below to check that you are
able to display the full image on your screen. If you have insufcient height or width,
you will have to reduce the overall image size in order to display the full image on
your screen.
10
9
8
4:3
7
6
5
Screen height
4
Aspect ratio
1.66:1
1.85:1
2.35:1
16:10
16:9
Notes
3
2
1
1 2 3 4 5 6 7 8 9 10
2.35:1 (Scope)
W = H x 2.35 H = W x 0.426
1.85:1
W = H x 1.85 H = W x 0.54
16:9 = 1.78:1 (native aspect ratio)
W = H x 1.78 H = W x 0.56
1.66:1 (Vista)
W = H x 1.66 H = W x 0.6
16:10 = 1.6:1
W = H x 1.6 H = W x 0.625
4:3 = 1.33:1
W = H x 1.33 H = W x 0.75
Screen width
Rev E October 2014 Page 2.5
2. Installation Digital Projection M-Vision Cine LEDUser Manual
Positioning the screen and projector
Optimum viewing position
For optimum viewing, the screen should be a at surface perpendicular to the oor.
The bottom of the screen should be 1.2m (4 feet) above the oor and the front row
of the audience should not have to look up more than 30° to see the top of the
screen.
The distance between the front row of the audience and the screen should be at
least twice the screen height and the distance between the back row and the screen
should be a maximum of 8 times the screen height. The screen viewing area should
be within a 60° range from the face of the screen.
Notes
The projector should be
installed as close to the
power outlet as possible.
The power connection should
be easily accessible, so that
it can be disconnected in an
emergency.
Ensure that there is at least
30cm (12in) of space between
the ventilation outlets and
any wall, and 10cm (4in) on
all other sides.
Do not install the projector
close to anything that
might be affected by its
operational heat, for instance,
polystyrene ceiling tiles,
curtains etc.
The image can be ipped for
rear projection (see section
4. Using the menus, Image
menu) and displayed without
the need for extra mirrors or
equipment.
However, you must ensure
that there is sufcient distance
behind the screen for the
projector to be correctly located.
Rear installation is generally
more complicated and advice
should be sought from your
local dealer before attempting it.
Page 2.6 Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual 2. Installation
Screen size vs throw distance
Throw distance is the distance measured from the front of the projector to the
screen. This is an important calculation in any projector installation as it determines
whether or not you have enough room to install your projector with the desired
screen size, and if your image will be the right size for your screen.
Calculating screen width and throw distance
Throw Distance = Screen Width x Lens Throw Ratio
Screen Width = Throw Distance Lens Throw Ratio
Notes
For more information about the
relationship between screen
size, throw distance and
converter lenses, see the Lens charts on the following pages.
Three models of the projector are available, tted with the following lenses:
Two optional converter lenses are available, which modify the throw ratios as shown
below:
0.8x converter 1.25x converter
• Short-throw lens 1.25–1.49:1 1.95–2.33:1
• Long-throw lens 1.48–1.92:1 2.31–3:1
These throw ratios are correct for images that ll the full width of the DMD. For
images that do not ll the full width, the throw ratio will be larger. For 4:3 images,
the throw ratio is increased by a factor of 1.33. The effect of this can be seen on the
lens charts on the following pages.
Do not confuse the focus range
with the zoom range:
- the focus range is the distance
over which the image can be
focused using the focus ring.
- the zoom range is the range
over which the throw ratio can
be changed using the zoom
ring.
The converter lenes are not
physically compatible with the
Fixed lens.
The 0.8:1 conversion lens
introduces up to 4% bow
distortion. Digital Projection
recommends caution when
using this lens
Rev E October 2014 Page 2.7
2. Installation Digital Projection M-Vision Cine LEDUser Manual
Lens charts for the short throw zoom lens
example
• You can display a 16:9 image with a screen width of 3m at a distance of 5m, but
for a screen width of 3.5m, you will need to use the 0.8x converter lens.
feet
metres
23 7
20 6
16 5
13 4
10 3
Screen width
7 2
16:9 images
Notes
using the 0.8x
converter lens
without a
converter lens
using the 1.25x
converter lens
3 1
1 2 3 4 5 6 7 8 9 10 11 12 metres
3 7 10 13 16 20 23 26 30 33 36 39 feet
23 7
20 6
16 5
13 4
10 3
Screen width
7 2
3 1
Throw distance
using the 0.8x
converter lens
4:3 images
without a
converter lens
using the 1.25x
converter lens
1 2 3 4 5 6 7 8 9 10 11 12 metres
3 7 10 13 16 20 23 26 30 33 36 39 feet
Throw distance
Page 2.8 Rev E October 2014
Digital Projection M-Vision Cine LEDUser Manual 2. Installation
Lens charts for the long throw zoom lens
example
• You can display a 4:3 image with a screen width of 3m at a distance of 6m, but
for a screen width of 2m, you will need to use the 1.25x converter lens.
feet
metres
23 7
20 6
16 5
13 4
10 3
Screen width
7 2
16:9 images
Notes
Note that for the long throw
lens, there is some overlap
between the range available
using the converter lenses and
that using no converter lens.
using the 0.8x
converter lens
without a
converter lens
using the 1.25x
converter lens
3 1
1 2 3 4 5 6 7 8 9 10 11 12 metres
3 7 10 13 16 20 23 26 30 33 36 39 feet
23 7
20 6
16 5
13 4
10 3
Screen width
7 2
3 1
Throw distance
using the 0.8x
converter lens
4:3 images
without a
converter lens
using the 1.25x
converter lens
1 2 3 4 5 6 7 8 9 10 11 12 metres
3 7 10 13 16 20 23 26 30 33 36 39 feet
Rev E October 2014 Page 2.9
Loading...
+ 61 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.