DIGI INTERNATIONAL
9350 Excelsior Blvd, Suite 700
Hopkins, MN 55343, USA
+1 (952) 912-3444 | +1 (877) 912-3444
www.digi.com
Digi Accelerated Linux (DAL) Release Notes
Connect IT Console Servers
Version 21.2.39.67
INTRODUCTION
This is a major firmware release for all DAL supported products. This is a recommended production
firmware release
SUPPORTED PRODUCTS
· Connect IT 4
· Connect IT 16
· Connect IT 48
· Connect IT Mini
KNOWN ISSUES
· Cellular metrics are not shown under the Settings → Status → Communications section of Digi
Remote Manager, but are shown under the Data Streams for the device. [DALP-768]
· Health metrics are uploaded to Digi Remote Manager unless the Monitoring > Device Health >
Enable option is de-selected and either the Central Management > Enable option is de-
selected or the Central Management > Service option is set to something other than Digi
Remote Manager [DAL-3291]
· Wired Internet connectivity is interrupted during cellular modem firmware updates [DAL-4647]
· The cellular Access technology configuration option is ignored if carrier PLMN locking is
enabled [DAL-4693]
UPDATE BEST PRACTICES
Digi recommends the following best practices:
1. Test the new release in a controlled environment with your application before you update
production devices.
2. Unless otherwise noted, apply updates in the following order:
a. Device firmware
b. Modem firmware
c. Configuration
d. Application
Digi recommends Digi Remote Manager or Digi aView for automated device updates. For more
information, follow the instructions for Digi Remote manager or Digi aView in the links below:
96000472_C Release Notes Part Number: 93001322_T Page 1
1. Instructions for Digi Remote Manager:
https://www.digi.com/resources/documentation/digidocs/90001436-13/default.htm#tasks/t_update_device_firmware.htm
2. Instructions for Digi aView:
https://www.digi.com/resources/documentation/digidocs/acl-kb/default.htm#Subsystems/kb-6300-cx/update-firmware.htm
If you prefer manually updating one device at a time, follow these steps:
1. Download the firmware file from the Digi firmware support page.
2. Connect to the device’s web UI by connecting your PC to the LAN Ethernet port of the device
and then going to http://192.168.210.1.
3. Select the System tab on the top navigation bar of the page, then select Firmware Update.
4. Select the Browse button in the Upload file section..
5. Browse for and select the downloaded firmware file.
6. Click the Update Firmware button.
TECHNICAL SUPPORT
Get the help you need via our Technical Support team and online resources. Digi oers multiple
support levels and professional services to meet your needs. All Digi customers have access to
product documentation. firmware, drivers, knowledge base and peer-to-peer support forums.
Visit us at https://www.digi.com/support to find out more.
CHANGE LOG
Mandatory release = A firmware release with a critical or high security fix rated by CVSS score.
For devices complying with ERC/CIP and PCIDSS, their guidance states that
updates are to be deployed onto device within 30 days of release
Recommended release = A firmware release with medium or lower security fixes, or no security fixes
Note that while Digi categorizes firmware releases as mandatory or recommended, the decision if
and when to apply the firmware update must be made by the customer aer appropriate review
and validation.
VERSION 21.2.39.67 (February 27, 2021)
This is a mandatory release
ConnectITmini-21.2.39.67.bin
SHA256:
6a0fda83f27055a1346d74eded4ba012c67de647d3237b77908b1a72ac80cfc9b0144c2c4
2b41868bc654af6e5900126ce0c68bb0781f5d085d1582ebff774f8
MD5: 37d5b03c24823114e235ac6724cb082c
ConnectIT4-21.2.39.67.bin
SHA256:
bb80bb050eb96f164234b5e77b3e1c8a17c002a1e90de92e0c9089ef2cd7ac37cdd08c72
2d455349425ff0c7c53b062ac174be46a90c281e45f64c3b3dca7ac8
MD5: ccc31728eb1f685b8af4091b531deebc
ConnectIT16-21.2.39.67.bin
SHA256:
6b9a1661d0e718d54a0e7086e0c67abe6a42b6e9efb213680592c19b16f94470092bdf96
8f006d5fda22dd3955f3b0488681498f24135500efcf1d9f7c6b6c61
96000472_C Release Notes Part Number: 93001322_T Page 2
MD5: 8cabc90a7738489cb7c786cc1716d9
ConnectIT48-21.2.39.67.bin
SHA256:
7c891bf64414341c006eaee42de28d312e116739a4ccc5e457627727931034f530c502c5f
28c477c390d339661564d49ff155df9e59fce3783b60f19f6302286
MD5: abbe72dda27f97a2d36579b81945a99a
FEATURES
1. Add the Location service to all DAL products. DAL devices can utilize several location
sources (cellular, GNSS, or user defined) to determine where it's located and report that to
Digi Remote Manager or other servers [DAL-724]
2. Add geo-fencing configuration options. This new features is found under Services →
Location → Geofence. It can be utilized to define one or more circular or polygonal geofence areas and then perform a set of actions when the device enters or leaves that area.
Current options for actions to perform are either factory erasing the device or running a
custom script. [DALP-711]
3. New modem scan CLI command for listing available carriers for the current modem and
SIM setup.
4. New Network → Interface → Modem → Network PLMN ID config setting to lock the SIM card
to a particular carrier based on its PLMN ID(note that the Carrier selection mode must be
set to Manual or Manual/Automatic in order to lock the SIM to a specific carrier) [DALP637]
5. Added local API to the web UI for automated configuration of the device [DALP-777]
6. Support remote CLI commands through Digi Remote Manager [DAL-4273]
7. New configuration options under System → Scheduled tasks → System maintenance to
automatically check for device and modem firmware updates, then notify in the CLI and
web UI when updates are available [DAL-4413]
ENHANCEMENTS
1. Added settings under Authentication → Serial to control Certificate Management for TCP
and autoconnect serial port setups [DALP-682]
2. Allow hidden/debug config settings to be controlled and preserved by DigiRM [DAL-4445]
3. Asymmetric preshared keys for IPsec tunnels [DALP-707]
4. Don't display Aggressive/Main mode or Xauth selections for IKEv2 IPsec tunnels [DAL-4142]
5. Update name and description of certificate settings for OpenVPN clients and servers [DAL-
4435]
6. Add digidevice.led python module to all products [DALP-710]
7. Add options to forward location information to a remote host over TCP [DALP-778]
8. Add new Forward interval multiplier configuration option under Services → Location →
Destination servers to control the number of location update intervals to wait before
sending location data to this server [DAL-4056]
9. Report location metrics as datapoints to DigiRM [DAL-4055]
10. Include the connection uptime of IPsec tunnels as datapoint metrics to Digi Remote
Manager [DAL-4062]
11. Add iptables TRACE tool for enhanced firewall debugging [DAL-4182]
12. Improved accuracy of the status shown for a modem during a firmware update
BUG FIXES
1. Fixed issue with utilizing soware flow control on serial ports set in remote-access mode
[DAL-3630]
96000472_C Release Notes Part Number: 93001322_T Page 3
2. Fix issue where a serial port could lock up and prevent access if flow control was enabled
[DAL-4585]
3. Fixed issue where non-primary DNS were queried through the wrong interface when
use_dns configuration option is set to primary [DAL-3156]
4. Report the phone number of the SIM as a health metric datapoint to Digi Remote Manager
[DAL-4440]
5. Fixed incorrect format of ICCID and IMEI metrics reported to Digi Remote Manager [DAL-
4440]
6. Fixed setup issue between custom firewall rules and IPsec tunnels [DAL-4433]
7. Fixed occasional issue preventing LM940 modems from re-establish their cellular
connection aer a modem firmware update [DAL-2933]
8. Fixed issue requiring a user to fix syslog configuration setting when updating from 20.5.x or
older firmware to 20.8.x/20.11.x firmware [DAL-4426]
9. Fixed rare issue where show system CLI command would display incorrect uptime details
[DAL-4350]
10. Fix issue with secondary CLI sessions showing stale configuration settings if the config is
updated elsewhere [DAL-4446]
11. Updated message displayed in web UI to direct the user to refresh the page aer erasing the
device back to default settings [DAL-2326]
12. Fixed issue where dynamic DHCP leases were not displayed in the CLI or web UI (bug
present on 20.11.x firmware versions) [DAL-4557]
13. Fixed inaccurate status of the Ethernet interface of a device in passthrough mode [DAL-
4543]
14. Fixed issue preventing web UI access if two-factor authentication was enabled (bug present
on 20.11.x firmware versions) [DAL-4509]
15. Fixed issue where CLI commands sent from DigiRM would crash the DAL device's connection
to DigiRM [DAL-4412]
16. Fixed issue preventing WAN/cellular connections from working if the interface was
configured with a single Interface Up Surelink test [DAL-4629]
SECURITY FIXES
The highest level vulnerability that has been fixed in this release is listed as a Critical CVSS score of
8.1 High
1. Update libcurl to version 7.74.0 (CVE-2020-8169, CVE-2020-8177) [DAL-4336]
2. Update to python version 3.6.12 (CVE-2020-14422) [DAL-4364]
3. Update OpenSSL to version 1.1.1i (CVE-2020-1971) [DAL-4326]
4. Update dnsmasq to version 2.83 (CVE-2019-14834, CVE-2020-25681, CVE-2020-25682, CVE-
2020-25683, CVE-2020-25684, CVE-2020-25685, CVE-2020-25686, CVE-2020-25687) [DAL3950]
5. Update web security settings with the following headers [DAL-4192]
1. Pragma: no-cache
2. Content-Security-Policy
3. X-Content-Type-Options: nosni
4. X-XSS-Protection: 1; mode=block
6. Set SAMEORIGIN in X-Frame-Options to uppercase [DAL-4192]
7. Automatically de-activate active user logins/sessions if the password for that user changes
8. Removed support for https CBC ciphers [DAL-4408]
9. Fixed XSS vulnerability on serial page in the local web UI (Bug present on firmware versions
20.11.x and older) [DAL-4646]
96000472_C Release Notes Part Number: 93001322_T Page 4
VERSION 20.11.32.168 (December 23, 2020)
This is a recommended release.
ENHANCEMENTS
1. Use PDP context 1 with Telus carrier SIMs [DAL-4332]
BUG FIXES
1. Fixed bug preventing Ethernet speed/duplex adjustment (aects firmware version
20.11.32.138) [DAL-4414]
VERSION 20.11.32.138 (December 2, 2020)
This is a mandatory release
ConnectITmini-20.11.32.138.bin
SHA256:
8aa6206f0957f2c2c739ca7fa2c0791c9d01d42503f0d7e7b5e7b6dddd6bd1e1de23a767
40a194557fcb7bf88078ef0ac2908d5f3df9d8545de1ac2cf2216b75
MD5: 5b85b919a0824e083f6cbc683385c373
ConnectIT4-20.11.32.138.bin
SHA256:
4dd5d927bea5cdb091393bf2aa91cc06670960bf54b4ca2885741c758f9c25aa3d399146
01903a0c0c39f23d193e6b6b7a5b213f80aba58892d2f9487de33e27
MD5: 93b8e5b3b9edf8a8e54e22518c0fe4be
ConnectIT16-20.11.32.138.bin
SHA256:
6fdb0d0d75364253f1ea7eae328f7ee0d999c021b2bcb5a353e13aa299fe052bbcd6519
4352ea43a6ecf0585166dd55b641590d0412a62cccea141a96a07d9
MD5: 40c04f4e978117146ef1a134b032
ConnectIT48-20.11.32.138.bin
SHA256:
3befaf4ea4d9a5263f5595f910fcc44a35745431689a90535112e326efe8b51bbc205f5706
4204fa57a02507da65cc6df5c6b5c9c78eaee44133cca410efe6ac
MD5: f15d325b2eaf90d03178c861da448d82
FEATURES
1. Add ssh and telnet commands to Admin CLI [DALP-664]
2. Add new modem firmware CLI commands for performing local or over-the-air remote
firmware updates to the cellular modem(s) in the device [DAL-2811]
3. Add new configuration options under Network → Devices for setting the link speed/duplex
of the device's Ethernet port(s) [DALP-135]
4. Add options for starting, stopping, and viewing serial port activity logs through the CLI, web
UI, or Digi Remote Manager [DALP-458]
5. Support for the Sierra EM9190/9191 5G modems [DALP-686]
6. Support for the Sierra EM7411 LTE CAT7 modem [DALP-608]
96000472_C Release Notes Part Number: 93001322_T Page 5
7. IPv6 IPsec tunnel support for full IPv6 tunnels, IPv6-over-IPv4, or IPv4-over-IPv6 tunnels
[DALP-581]
8. IPsec XFRM interfaces for enhanced control over IPsec tunnels and the network interfaces
associated to them. This allows users to select tunnels for multiple networking features,
including static routes, policy-based routes, access control lists, and routing priority based
on metric. [DAL-490]
9. Inclusion of the Python pip for installing external modules/libraries [DAL-4078]
ENHANCEMENTS
1. Add Services → Location options for configuring GPS or GNSS location communication
[DALP-724]
2. GPS/GNSS support for the Quectel EG25-G modem [DALP-713]
3. Add cellular technology icon to the Dashboard in the web UI [DAL-3673]
4. Add link to product User Guide under the User drop-down menu at the top-right of the web
UI [DALP-569]
5. Added help button to System → File System page of the web UI [DALP-569]
6. Added new Status → Modbus Gateway service page to the web UI to display information
about modbus clients and servers connected to the gateway [DALP-671]
7. Added show modbus-gateway CLI command to view the status of Modbus gateway service
[DALP-671]
8. Updated show modem CLI command to display historical information about the modem if
it is in the process of updating firmware [DAL-1504]
9. Added new Services → Ping responder configuration settings for controlling what
interfaces and firewall zones the DAL device responds to ICMP requests on [DAL-1565]
10. Enhance IPSec tunnels to wait for passing Surelink tests (if configured) before initiating
outbound tunnels [DAL-3878/DAL-3774]
11. Add m2m.telus.iot Telus APN to fallback list [DAL-3911]
12. Add psmtneorm and edneopate010.dpa AT&T APNs to fallback list [DAL-4041/DAL-4045]
13. Add reseller and tracfone.vzwentp Tracfone APNs to the AT&T and Verizon fallback lists
DAL-4098]
14. Add new 890103 and 890141 ICCID prefixes and 31030 PMND ID matchers to AT&T APN
fallback list [DAL-3934/DAL-4041]
15. Add service.qcdm.secure option to enable/disable encrypted QXDM access to the cellular
modem in the DAL device [DAL-3964]
16. Add missing modem firmware and SIM details to datapoints uploaded to Digi Remote
Manager [DAL-4040]
17. Show uptime for connection to Digi Remote Manager on the Dashboard web UIpage in
days/hours/minutes/seconds instead of just minutes [DAL-3691]
18. Updated network bridges to use the MAC address of the first device listed in Network →
Bridges → [bridge_name] → Devices as the MAC address for the bridged interface [DAL3949]
19. Add link in the firmware update window on the Status → Modem page to direct users to the
configuration options to schedule a modem firmware update [DALP-725]
20. Updated the help text on the login page to provide a more generic image [DAL-3916]
21. Added option when copying serial port settings on the System → Serial Configuration page
to optionally copy the label of the serial port [DAL-3842]
22. Removed duplicate modem signal information from the Modem → Status page [DAL-3680]
23. Added a DSCP option to policy-based routes to allows users to match the routing rule by
the type of DSCP field in the packet [DAL-3867]
96000472_C Release Notes Part Number: 93001322_T Page 6
24. Added a defaultroute option for matching policy-based routes to the device's active
default route [DAL-4130]
25. Hide the Monitoring → Device Health configuration options if the device is not enabled for
Digi Remote Manager central mangement [DAL-3825]
26. Update header types for the cellular modem name and network type on the Dashboard
page
27. Create system log when Surelink DNS tests are skipped because the interface doesn't have
any DNS servers [DAL-4224]
28. Added python to the ConnectIT4 product [DAL-4061]
29. Hide main/aggressive mode option when using IKEv2 [DAL-4142]
BUG FIXES
1. Fixed missing default settings in configuration profiles created in Digi Remote Manager (bug
aects firmware versions 20.8.x and older) [DALP-658]
2. Fixed missing option for setting the SIM Slot Preference in configuration profiles in Digi
Remote Manager (bug aects firmware versions 20.8.x and older) [DAL-3912]
3. Fixed format of user passwords when displayed in Digi Remote Manager (bug aects
firmware versions 20.8.x and 20.5.338.58) [DAL-3889]
4. Fixed issue with policy-based routing not working in conjunction with multiple IPsec
tunnels (bug aects firmware versions 20.8.x and older) [DAL-3515]
5. Fixed issue preventing OpenVPN server-managed certificates from being re-generated if the
process was interrupted (bug aects firmware versions 20.8.x and older) [DAL-3803]
6. Fixed issue preventing OpenVPN client from using an autogenerated config file from a tap-
bridge openvpn server (bug aects firmware versions 20.8.x and older) [DAL-3881]
7. Fixed some formatting output of the show system verbose CLI command (bug aects
firmware versions 20.8.x and older) [DAL-3805]
8. Fixed issue preventing VRRP interoperability between DAL devices and SarOS devices (bug
aects firmware versions 20.8.x and older) [DAL-4130]
9. Update VRRP+ to properly handle changes in network interface statuses bug aects
firmware versions 20.8.x and older) [DAL-4274]
10. Removed poorly formatted script contents from the show scripts CLI command output
[DAL-3315]
11. Fixed non-working system disable-cryptography CLI command [DAL-4169]
12. Fixed second-stage erase functionality on devices not enabled for aView management [DAL-
3944]
13. Fixed issue preventing multicast traic from being sent through a GRE tunnel [DAL-3879]
14. Fixed issue preventing a firewall rule from being setup for OSFPv2 entries [DAL-3869]
15. Fixed rare crash caused when a Quectel modem disconnected [DAL-3867]
16. Fixed behavior of the WWAN Service LED to blink when a modem firmware update is in
progress (bug aects firmware versions 20.8.x and older) [DAL-3963]
17. Fixed issue preventing ConnectIT-Mini devices and Quectel EG25-G modules from
connecting with Verizon private APNs (bug aects firmware versions 20.8.x and older) [DAL3605/DAL-3276]
18. Removed SIM slot 2 references and options from the configuration settings in the
ConnectIT-Mini [DAL-3930]
SECURITY FIXES
The highest level vulnerability that has been fixed in this release is listed as a Critical CVSS score of
9.1
96000472_C Release Notes Part Number: 93001322_T Page 7
1. Disallow TCP forwarding from incoming SSH connections [DAL-3938]
2. Remove sensitive information from HTTP GET requests (CVSS score: 5.7 Medium CVSS:3.1/
AV:N/AC:H/PR:H/UI:R/S:U/C:H/I:H/A:N) [DAL-3938]
3. Update to linux kernel 5.8 (CVSS score: 3.7 Low CVE-2020-16166 CVSS:3.1/AV:N/AC:H/PR:N/
UI:N/S:U/C:L/I:N/A:N) [DALP-678]
4. OpenSSH updated to version 8.3p1 (CVSS score: 2.2 Low
CVSS:3.1/AV:N/AC:H/PR:H/UI:N/S:U/C:L/I:N/A:N) [DAL-3299]
5. OpenSSL updated to vesion 1.1.1h (CVSS score: n/a) [DAL-4037]
6. OpenVPN updated to version 2.4.9 (CVSS score 9.1 Critical CVE-2018-7544
CVSS:3.0/AV:N/AC:L/PR:N/UI:N/S:U/C:H/I:N/A:H) [DAL-3862]
7. Linux shell/bash updated to version 5.0 (CVSS score: n/a) [DAL-3763]
8. jQuery updated to version 3.5.1 (CVSS Score: 6.1 Medium CVE-2020-11022 CVE-2020-11023)
[DAL-3547]
9. Updated WebU session token to use AES-256-GCM cipher (CVSS score: n/a) [DAL-4000]
10. Prevent web asset access from unauthorized logins (CVSS score: 5.3 Medium CVSS:3.1/AV:N/
AC:L/PR:N/UI:N/S:U/C:L/I:N/A:N) [DAL-3835]
11. Add script CSP headers to the web UI (CVSS score: n/a) [DAL-3629]
12. Added extra layer of firmware verification to ensure the firmware matches the target
hardware variant and prevent firmware modifications (CVSS score 1.9 Medium
CVSS:3.1/AV:L/AC:H/PR:H/UI:N/S:U/C:N/I:L/A:N) [DAL-3511]
13. Prevent command injection through modemadvanced, modem_install, and firmware
webpages (CVSS score: 6.8 Medium CVSS:3.1/AV:N/AC:H/PR:N/UI:R/S:U/C:H/I:H/A:N) [DAL4093/DAL-4104/DAL-4046]
14. Prevent manual addition of files to an encrypted filesytem outside of the device itself (CVSS
score: 6.1 Medium CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:N/I:H/A:H) [DAL-4149]
15. Restrict memory allocation of tcpdump (CVSS score: 7.5 High CVE-2020-8037
CVSS:3.1/AV:N/AC:L/PR:N/UI:N/S:U/C:N/I:N/A:H) [DAL-4226]
16. Removed expired aView and AVWOB certificates [DAL-3467]
17. Encode MAC address in URL used to sync with aView to prevent privileged escalation [DAL-
4304]
VERSION 20.8.22.32 (August 28, 2020)
This is a mandatory release
ConnectITmini-20.8.22.32.bin
SHA256: 9c21f9662754e77def26af3ea0804f84267f17c28e2ce40bfad5bce655a1add3
MD5: 926608bbdeff50c962f034ecd71c65f4
ConnectIT4-20.8.22.32.bin
SHA256: ab46ac98bc661fa5e56559c6328229d18b10e2c76960ad077c464fb1e75a03f3
MD5: 4d519c4318a4eac129739ae82cdef244
ConnectIT16-20.8.22.32.bin
SHA256: 4ae37b9d855c87afd767d02a89121a49cbe95e857df6fd4cd220cb838a7ac790
MD5: f89c26333c0a346e7635e082db92c639
ConnectIT48-20.8.22.32.bin
SHA256: 3235a52e53cd7a27cf04badf66f4cc7bd5aa1fdd2415ae1fe705e1c4a7f9093d
MD5: 926ae9e13ee56d080bec471f064761f6
FEATURES
1. Add new System → Scheduled taks → Allow scheduled scripts to handle SMS
96000472_C Release Notes Part Number: 93001322_T Page 8
configuration option to allow custom python scripts to handle sending/receiving SMS
messages [DALP-488]
2. Add digidevice.sms python module for sending/receiving SMS messages in a custom python
script [DALP-488]
3. Add ability to load custom factory config file from the local filesystem, which if present is
loaded when the device is reset to default settings [DALP-394]
1. The config file is the same as what can be downloaded when a user saves/exports the
configuration from the Configuration Maintenance page in the local web UI. That .bin
config file can be placed in /opt/custom-default-config.bin
4. DMNR Verizon Private Network support with new settings under VPN → NEMO [DALP-457]
5. Added Serial Modbus Gateway service for utilizing the Modbus protocol to communicate
with serial ports [DALP-573]
1. Configuration settings for the Modbus Gateway are found under Services → Modbus
Gateway
6. MQTT client support via Paho Python module [DALP-590]
1. Note: not available on the ConnectIT4
7. Added Ethernet network bonding to allow the same MAC address and IP configuration to be
shared for multiple physical Ethernet ports in either active/backup or round-robin mode
[DALP-589]
1. Configuration options found under Network → Interfaces → Ethernet bonding. Bond
devices created here can then be assigned to network interfaces
2. Note: not available on the ConnectIT4 or ConnectIT-Mini
8. VRRP+ options added under Network → VRRP → VRRP+ for validating primary or backup
connectivity and automatically changing VRRP priority [DALP-289]
1. Note a SureLink test must also be enabled for the network interface the VRRP entry is
assigned to
9. Cisco Umbrella content filtering options added under Firewall → Web filtering service
configuration section [DALP-524]
ENHANCEMENTS
1. Disable voice services on Quectel EC25-AF when using T-Mobile SIMs [DAL-3707]
2. Add -I source address option to the ping CLI command [DAL-3682]
3. Add service.modbus.debug config option to enable debug logging on Serial Modbus [DAL3561]
4. Add Central management configuration options for any DAL product to sync with aView,
ARMT, or AVWOB [DALP-626]
5. Add 4GM and 4GT options to the Network->Modems→Access technology settings to
specify a CAT-M modem to only connect on LTE CAT-M1 or NB-IoT, respectively [DALP-472]
6. Add options under System → Log → Server list to allow users to specify the TCP/UDP
protocol and port of the remote syslog server [DALP-593]
7. Added configuration option under Serial → TCP connection to specify encrypted vs nonencrypted connection types
8. Added configuration option under Serial → TCP/Telnet/SSH connections to enable/disable
TCP keep-alive messages and nodelay
9. Added new Base settings checkbox on custom serial configuration page in the web UI to
allow users to specify whether they want to copy the base serial settings or not [DAL-3775]
10. Added new Monitoring→Device Health→Data point tuning configuration options to fine
tune what datapoints are uploaded as health metrics to Digi Remote Manager
11. Added new Monitoring→Device Health → Only report changed values to Digi Remote
96000472_C Release Notes Part Number: 93001322_T Page 9
Manager option to control sending metrics to Digi Remote Manager on the basis of whether
the values have changed since they were last reported [DAL-3386]
12. Reduced data usage by 80% (based on default settings) for reporting health metrics to Digi
Remote Manager [DAL-3394]
13. Fade Configuration saved pop-up window 5 seconds aer clicking the Apply button [DAL3451]
14. Added new Status → Scripts page in the web UI to view custom scripts and applications
configured in the device, along with their status (running vs idle) [DALP-533]
15. Add options in CLI to show and manually stop any custom scripts or applications [DALP533]
16. Added Duplicate firmware option on the Firmware Update page in the local web UI to copy
the active firmware to the secondary firmware partition [DALP-565]
17. Add system duplicate-firmware CLI command to copy active firmware to the secondary
firmware partition [DALP-565]
18. Move update firmware CLI command to be under system [DAL-3092]
19. Add show vrrp CLI command to display the status of any configured VRRP instances [DAL2953]
20. Use a random unprivileged port for performing ntp time syncs if standard port 123 fails
[DAL-3650]
21. Added new Authoritative option under TACACS+, RADIUS, and LDAP user authentication
methods to prevent falling back to additional authentication methods if enabled [DAL-3314
& DALP-540]
22. Update to ModemManager 2020-05-19 [DAL-3254]
1. libqmi: updated to 1.25.4+
2. ibmbim: updated to 1.20.4+
3. libgudev: updated to version 233
4. Improved support for Quectel EC25/EG25 modules
BUG FIXES
1. Fix LED behavior to account for Surelink pass/fail results [DAL-3688]
2. Fixed issue preventing RADIUS/TACACS+ authentication from working unless local-user
authentication was also configured [DAL-3701]
3. Fixed issue preventing 1002-CMG4 modem from connecting with Verizon private APN SIMs
[DAL-3276]
4. Fixed issue where device would remain connected to Digi Remote Manager even aer
cloud.service was changed to aView or disabled. Rebooting the device previously resolved
the issue [DAL-3504]
5. Fixed bug where IPsec tunnels with multiple policies would only properly route traic for
the last policy configured [DAL-3448]
6. Fixed missing CPU usage stats in show system CLI output [DAL-2540]
7. Fixed improper value of the active SIM slot in the modem sim-slot show CLI command
output when SIM slot 2 was in use [DAL-3569]
8. Fixed issue preventing network interfaces from initializing if the interface name was longer
than 7 characters [DAL-2327]
9. Fixed issue preventing WAN passthrough mode if WAN was configured with a static IP [DAL3097]
10. Fixed errors displayed in CLI when configuring a USB serial port in remote access mode
[DAL-3207]
11. Fixed issue preventing users from configuring an IP address as a remote syslog server [DAL-
96000472_C Release Notes Part Number: 93001322_T Page 10
3433]
12. Handle incorrect value occasionally returned by by Telit LM940/LM960 module when
querying to see which SIM slot is in use [DAL-3481]
13. Fixed issue preventing cellular modem connectivity if a custom gateway/subnet was
configured but the modem wasn't in passthrough mode [DAL-3585]
14. Fixed issue causing aView IPsec tunnel (if enabled) to randomly fail when device was in
passthrough mode [DAL-3657]
15. Fixed permission issue on /opt/custom/ directory preventing users from setting up custom
CSS and logos [DAL-3710]
SECURITY FIXES
The highest level vulnerability that has been fixed in this release is listed as a High CVSS score of 6.7
1. Update to Linux kernel 5.7 (CVE-2020-10732 CVSS Score: 4.4 Medium
CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:L/I:N/A:L) [DAL-3322]
2. Added local user login rate limiting to default lockout additional login attempts for 15
minutes aer 5 login failures per user (Score: 6.7 Medium
CVSS:3.1/AV:L/AC:H/PR:N/UI:N/S:U/C:H/I:H/A:N) [DAL-3390 and DAL-3505]
1. New configuration options are under the Login failure lockout section for each user in
the Authentication → User settings
3. Prevent /etc/config/start from running when shell is disabled (Score: 5.2 Medium
CVSS:3.1/AV:L/AC:H/PR:H/UI:N/S:U/C:H/I:L/A:L) [DAL-2846]
4. Prevent file path expansion on Firmware Update and File System pages in the local web UI
(Score: 3.2 Low CVSS:3.1/AV:L/AC:L/PR:H/UI:N/S:U/C:L/I:N/A:N) [DAL-3513, DAL- 3471, &
DAL-3518]
5. Obfuscate text when showing the SIM PIN (Score: 3.2 Low
CVSS:3.1/AV:L/AC:L/PR:H/UI:N/S:C/C:L/I:N/A:N) [DAL-3462]
6. Set HTTP Auth Cookie as secure in the local web UI (Score: 3.1 Low
CVSS:3.1/AV:N/AC:H/PR:N/UI:R/S:U/C:N/I:L/A:N) [DAL-3393]
7. Fixed leaked file descriptors on serial connections [DAL-3202]
VERSION 20.5.38.58 (July 20, 2020)
This is a recommended release
ENHANCEMENTS
1. Increased minimum password complexity to at least 10 characters containing at least one
uppercase letter, one lowercase letter, one number, and one special character [DAL-3491]
1. Note: Devices that were running older firmware that had user passwords that do not
meet these minimum requirements aer upgrading to 20.5.38.58 will still be able to use
that password to authenticate with the device. However, if the user attempts to update
user's password in the DAL device's configuration settings aer upgrading to 20.5.38.58,
the updated password must comply with the new minimum requirements
BUG FIXES
1. Fixed delay in connecting with FirstNet SIMs caused by interference from Lightweight M2M
(LWM2M) service on Telit modules [DAL-3236]
2. Prevent interruptions to QCDM/QXDM port on Sierra modems caused by ModemManager
interaction [DAL-3469]
3. Fixed bug preventing dual-APN connectivity with AT&T SIMs and Sierra modems [DAL-3586]
SECURITY FIXES
96000472_C Release Notes Part Number: 93001322_T Page 11
The highest level vulnerability that has been fixed in this release is listed as a High CVSS score of 6.5,
which is rated as a Medium
1. Removed remote_control service used when receiving remote commands from
aView/ARMT/AVWOB in favor of HTTPS secure commands. Vulnerability discovered by Stig
Palmquist (CVE pending) [DAL-3460]
2. Add failed login attempts to event log sent to remote syslog servers, if enabled [DAL-3492]
VERSION 20.5.38.39 (May 29, 2020)
This is a mandatory release
FEATURES
1. LDAP user authentication [DALP-192]
2. Add option on the System → Firmware Update page in the web UI to have the DAL device
query a firmware server for available firmware updates [DALP-481]
3. Add configuration options under Central management for a proxy connection to Digi
Remote Manager [DAL-3150]
4. Added new Enable watchdog configuration option to monitor the connection to Digi
Remote Manager, along with options to reboot the device or restart its connection to Digi
Remote Manager if the watchdog times out. The default settings are to restart the
connection to Digi Remote Manager if the watchdog times out aer 30 minutes [DAL-2954]
5. New application mode for serial ports to allow full control of serial ports through custom
python/shell programs. Also allows additional USB-to-serial adapters to be configured and
connected to using the /dev/serial/<config_key_name> path [DAL-2807]
ENHANCEMENTS
1. Added the ability to configure DHCP pools larger than /24 subnets [DAL-2864]
2. Add a statusall option to the show ipsec CLI command to display verbose IPsec status
[DAL-2711]
3. Use modem PDP context 1 when an AT&T SIM in inserted to match new requirements from
AT&T [DAL-3093]
4. Add AT&T FirstNet IMSIs so they can be dierentiated from other types of AT&T SIMs [DAL3163]
5. Added Python HID module to allow the DAL device to control PSUs via Python programs
[DAL-2092]
6. Allow network analyzer to be configured to monitor any network interface instead of just
wired Ethernet ports [DAL-2146]
7. Added option to ping CLI command to ping a broadcast address [DAL-2571]
8. Added new health metric to report the interface used by the DAL device for its configured
IPsec tunnels [DAL-2710]
9. Added new health metric to report the LTE SNR value of the modem(s) on the DAL device
[DAL-2904]
10. Limit metrics upload to no more than 2 per minute if backlogged [DAL-2870]
11. Added new Locally authenticate CLI configuration option to control whether a user is
required to provide device-level authentication when accessing the console of the device
through Digi Remote Manager. Default is to allow console access without providing devicelevel authentication, since the user is already logged in and authenticated through Digi
Remote Manager [DAL-1510]
12. Report device SKU in RCI response to Digi Remote Manager [DAL-2940]
13. Add wbdata APN to fallback list [DAL-3182]
96000472_C Release Notes Part Number: 93001322_T Page 12
14. Improved recovery of Telit modem firmware updates should the update get interrupted
[DAL-2984]
15. Fixed spelling of System utilization chart on Intelliflow page in the local web UI [DAL-2260]
16. Added new Health sample upload window debug configuration option to provide a delay
window/jitter when uploading health metrics to Digi Remote Manager (default 2-minutes)
[DAL-2607]
17. Commonize the format and naming of rx/tx health metrics reported to Digi Remote Manager
[DAL-2896]
18. Add IPv6 options to traceroute CLI command [DAL-2618]
19. Add count of bytes transmitted and received to the output of the show network interface
X CLI command [DAL-2980]
20. Updated mmcli-dump command used when generating a support report to only run its list
of AT commands on the cellular modem once [DAL-3013]
21. Updated placement of the Apply button on the Device Configuration page of the web UI to
account for usability on smaller screens and keep it always visible when scrolling [DAL3029]
22. Display the secondary/alternate firmware image version as the Alt. Firmware Version in
the output of the show system CLI command [DAL-3057]
23. Retain modem firmware files in the event that the firmware upgrade was interrupted [DAL2856]
24. Renamed OpenVPN server device type configuration options to clarify which options are
OpenVPN managed versus device-only [DAL-2857]
25. Changed the Idle timeout configuration settings for remote-access serial ports to use to
blank instead of 0s, to better match the format of the Idle timeout option for user login
sessions [DAL-2623]
26. Added a 5-second wait time between setting LTE band configuration updates on a Telit
modem and rebooting the modem to apply the configuration change [DAL-2972]
27. Add support for AES_GCM family of IPsec ciphers [DAL-2715]
BUG FIXES
1. Load FirstNet-specific firmware on Telit LM960 modems when a FirstNet SIM is present (bug
aects firmware versions 20.2.x and older) [DAL-3163]
2. Fix VRRP crashes by upgrading keepalived to version 20.0.20 (bug aects firmware versions
20.2.x) [DAL-3181]
3. Prevent IPsec tunnel from being setup if its local network/interface is down (bug aects
firmware versions 20.2.x and older) [DAL-2336]
4. Fixed rare issue where the cellular modem could not initialize aer resetting the modem
(bug aects firmware versions 20.2.x and older) [DAL-1409]
5. Update analyzer to continue running even if the users SSH session ends (bug aects
firmware versions 20.2.x and older) [DAL-2154]
6. Prevent re-uploading of invalid health metrics data if Digi Remote Manager sends a
response that the contents of the health metrics are invalid (bug aects firmware versions
20.2.x and older) [DAL-2868]
7. Fixed timing issue where an IPsec tunnel configured to be built through a specific interface
would not be brought down properly if that network interface went down (bug aects
firmware versions 20.2.x and older) [DAL-3023]
8. Fixed issue preventing backup IPsec tunnel from being established when primary/preferred
tunnel was down (bug aects firmware versions 20.2.x) [DAL-3024]
9. Fixed intermittent reporting issue where web UI and CLI would list the modem as registered
when it was actually connected (bug aects firmware versions 20.2.x and older) [DAL-2329]
96000472_C Release Notes Part Number: 93001322_T Page 13
10. Fixed failing SureLink IPv6 ping tests (bug aects firmware versions 19.11.x through 20.2.x)
[DAL-2488]
11. Fixed issue with applying policy-based routes to incoming packets from the Internet (bug
aects firmware versions 20.2.x and older) [DAL-2589]
12. Fixed bug preventing passthrough mode from functioning if multicast was also enabled
(bug aects firmware versions 20.2.x and older) [DAL-2709]
13. Fixed rare issue with not receiving a SCEP certificate from the server due to timing issues
between requesting the certificate with a private key and when that certificate can be
downloaded (bug aects firmware versions 20.2.x and older) [DAL-2850]
14. Fixed error displayed in show modem CLI output when modem was not connected (bug
aects firmware versions 20.2.x and older) [DAL-2959]
15. Fixed bug preventing local configuration backups if the configuration directory contained
files or directory paths longer than 100 characters (bug aects firmware versions 20.2.x and
older) [DAL-3137]
16. Fix non-working custom DHCP options (bug aects firmware versions 20.2.x) [DAL-3071]
17. Fix corrupted configuration schema settings aer issuing a config revert CLI command
(bug aects firmware versions 19.8.x through 20.2.x) (bug aects firmware versions 20.2.x
and older) [DAL-3194]
18. Fixed issue where IPsec tunnel is built through default route instead of the configured local
interface (bug aects firmware versions 20.2.x) [DAL-2889]
19. Removed unsupported LED options listed for LR54 units in their digidevice.led Python
module options (bug aects firmware versions 20.2.x) [DAL-3250]
20. Removed empty, blank row from Filesystem page in the web UI when listing the contents of
an empty directory (bug aects firmware versions 20.2.x and older)
21. Fixed issue preventing users from downloading the ovpn client configuration file from the
web UI on the Chrome browser (bug aects firmware versions 20.2.x and older) [DAL-3262]
SECURITY FIXES
The highest level vulnerability that has been fixed in this release is listed as a High CVSS score of 7.5
1. Update to openssh-8.2p1 (CVE-2019-6111 – CVSS Score: 5.8) [DAL-2860]
2. Fixed user escalation exploit through cloud.drm.sms configuration option (CVSS Score:6.0
Severity:Medium Matrix: AV:L/AC:L/PR:H/UI:N/S:U/C:H/I:H/A:N) [DAL-2887]
3. Fixed user escalation exploit through Label configuration setting for serial ports (CVSS
Score: 6.0 Severity: Medium Matrix: AV:L/AC:L/PR:H/UI:N/S:U/C:H/I:H/A:N) [DAL-3011]
4. Fixed password exploit through web token (CVSS Score: 5.6 Severity: Medium Matrix:
AV:L/AC:H/PR:H/UI:R/S:U/C:H/I:H/A:N) [DAL-3069]
5. Update StrongSwan to 5.8.3 [DAL-2866]
6. Updated iputils to s20190709 and traceroute to version 2.1.0 [DAL-2338]
7. Upgrade Linux kernel to version 5.6 [DAL-2873]
8. Update ipset to version 7.6 [DAL-2853]
9. Update OpenSSL to 1.1.1g (CVE-2020-1967 - CVSS Score – 7.5 HIGH) [DAL-2977]
10. Prevent DOM XSS (cross-site scripting) exploit on Terminal page in the web UI (CVSS Score:
4.2 Severity: Medium Matrix: AV:N/AC:H/PR:N/UI:R/S:U/C:L/I:L/A:N) [DAL-3068]
11. Prevent user escalation exploit through netflash options in web UI (CVSS Score: 4.1 Severity:
Medium Matrix: AV:L/AC:H/PR:H/UI:N/S:U/C:N/I:H/A:N) [DAL-3129]
12. Prevent use-aer-free exploit in CLI configuration of OpenVPN (CVSS Score: 5.7 Severity:
Medium Matrix: AV:L/AC:H/PR:H/UI:N/S:U/C:H/I:H/A:N) [DAL-2963]
13. Prevent XSS vulnerability on the Filesystem page in the web UI where a directory name
with HTML embedded in it would be rendered as HTML rather than plain text (CVSS Score:
96000472_C Release Notes Part Number: 93001322_T Page 14
4.6 Severity: Medium Matrix: AV:L/AC:H/PR:H/UI:R/S:U/C:L/I:H/A:N) [DAL-3200]
14. Prevent unauthenticated users from downloading the ovpn client configuration file from
the web UI (CVSS Score: 5.6 Severity: Medium Matrix: AV:N/AC:L/PR:N/UI:N/S:U/C:L/I:N/A:N)
[DAL-3133]
VERSION 20.2.162.162 (March 17, 2020)
This is a mandatory release
ENHANCEMENTS
1. Add MAC address is support report filename [DAL-2863]
2. Add firstnet-broadband APN for AT&T FirstNet SIMs [DAL-2876]
3. Use ims instead of vzwims APN on Verizon SIMs for proper IMS registration [DAL-2883]
BUG FIXES
1. 1002-CM04/1003-CM11: Fixed cellular high-speed throughput performance issues caused by
CPU slowdown and timing of gathering cellular signal details [DAL-2802]
2. 1003-CM11: Fixed inability to utilize SIM slot 2 of an device with a Telit LE910c4-NF or LM940
modem when the two SIM slots contained SIMs from diering carriers [DAL-2897 & DAL-2986]
3. Fix health metrics warnings in Digi Remote Manager stating the local filesystem's /opt/ directory
was full when it wasn't [DAL-2769]
4. Fixed missing Rx/Tx bytes in show modem CLI command output [DAL-2804]
5. Fixed issue preventing multicast packets from being sent through a network bridge [DAL-2774]
6. Fixed auto-reboot aer restoring configuration file through local web UI [DAL-2862]
7. Fixed inability to update modem firmware on Sierra EM7511 modules [DAL-2794]
8. Fixed improper modem firmware selection on Telit LM960 module when using a T-Mobile SIM
[DAL-2376]
9. Fixed bug causing the configured Reboot Time to always occur in UTC instead of local timezone
(issue present in older 20.2.162.x firmware versions)[DAL-2859]
10. Fixed bug preventing analyzer from being stopped in the CLI [DAL-2892]
SECURITY FIXES
1. Fix cross-site scripting (XSS) vulnerability on various Status pages in the local web UI [DAL-2818]
2. Fix cross-site scripting (XSS) vulnerability on Configuration page in the local web UI [DAL-2819]
3. Fix cross-site scripting (XSS) vulnerability on Terminal page in the local web UI [DAL-2823]
4. Fix cross-site scripting (XSS) vulnerability on File System page in the local web UI [DAL-2823]
5. Prevent script injection exploit on the Configuration Maintenance page in the local web UI [DAL2797]
6. Prevent unauthorized read/write access to /opt/config/ and /opt/boot when `Interactive Shell`
is disabled [DAL-2865]
7. Prevent analyzer output from being saved outside of the /etc/config/analyzer directory [DAL2672]
VERSION 20.2.162.90 (March 11, 2020)
This is a mandatory release.
NEW FEATURES
1. Telit LM960 LTE CAT18 modem support [DALP-487]
96000472_C Release Notes Part Number: 93001322_T Page 15
2. Quectel EC25-AF LTE CAT4 modem support [DAL-1817]
3. Digi Remote Manager is set as the default portal for all DAL products [DALP-393]
l Central management via Digi Remote Manager will not be enabled if you upgrade a device
running 19.11.x or older firmware that was previously syncing with an aView instance to
20.2.x or newer firmware, but can be enabled if desired. However, if the device running
20.2.x or newer firmware gets reset (e.g. if someone presses the Erase button on the device,
or erases its config through the web UI or Admin CLI), the device will sync with Digi Remote
Manager by default.
4. Added SureLinkTM default connectivity tests on all WAN interfaces [DALP-402]
l SureLink tests (previously referred to as Active Recovery) will not be enabled by default if
you upgrade a device from 19.11.x or older DAL firmware to 20.2.x or newer firmware, but
can be enabled if desired. However, if the device running 20.2.x or newer firmware gets
reset (e.g. if someone presses the Erase button on the device, or erases its config through
the web UI or Admin CLI), the default SureLink tests will be enabled as part of the default
settings of the device.
5. New web UI pages added under the System drop-down with enhanced serial details and
configuration [DALP-465]
6. Support for firmware/OTA updates on Quectel modems [DALP-419]
7. AT&T LWM2M support for Telit LM940/LM960 modems [DAL-2476]
ENHANCEMENTS
1. Prevent access to web UI until HTTPS is ready [DAL-603]
1. Until the SSL cert is generated, users trying to access the web UI via standard http will
receive a redirect page stating that the cert is generating. Once the SSL cert is generated,
users accessing the web UI via standard http will be automatically redirected to the https
link
2. Show multiple bands for Telit modems if carrier-aggregation is supported and active [DAL-
2624]
3. Added additional Telit-specific AT commands to mmcli-dump of support report
4. Improved Role-based access on local web UI, SSH, and remote access [DALP-415]
Includes new configuration options
· Allow shell - NOTE if this options is disabled and subsequently re-enabled, the DAL device
will reset to default settings
· If disabled, the following changes are implemented
a) Forced all custom scripts to be sandboxed.
b) Script sandboxing uses a tighter profile that prevents /bin/sh
access.
c) Sandbox custom firewall scripts to a profile that only allows
iptables/ipset/arptables/ip and access to /proc and /sys files.
Basically all things firewall related but very locked down.
The commands are still run in the shell, but no external commands
are available, so the script is limited to basic loops and variable
access and no escaping.
· Under each user group under Authentication → Groups in the configuration settings:
· Admin access
· Access level
· Interactive shell access
96000472_C Release Notes Part Number: 93001322_T Page 16
5. New default break sequence ~b for serial connections [DALP-253]
6. Report MCC/MNC/CID/LAC values in health metrics to Digi Remote Manager [DAL-2502]
7. Add digicpn.gw12.vzwentp Verizon APN to fallback list [DAL-2283]
8. Change default OpenVPN Certificate Issuer details from Accelerated to Digi [DAL-2449]
9. Change default SSL certification from Accelerated to Digi [DAL-1336]
10. Dual-APN support on Sierra EM7511 modem [DAL-2311]
11. Include AT#RESETINFO and Quectel-specific AT commands in support report [DAL-2394]
12. Rename Configuration Management page under the System section of the web UI to
Configuration Maintenance [DAL-2549]
13. Added link under System drop-down in web UI to download the support report
14. Update the Digi Remote Manager link under the System drop-down in the web UI to open in a
new tab [DAL-2294]
15. Update the Authentication → Idle timeout setting to have a default value of 10-minutes
(previously the default was blank) [DAL-2292]
16. Send up to 4 IPsec tunnels' details as health metrics reported to Digi RM [DAL-1476]
17. Change the default behavior of the SIM failover alternative settings from None to Reset
modem [DAL-2687]
18. Renamed Signal Strength references to Signal Quality [DAL-2707]
19. On the Network Status page of the web UI, add Interface is up message in SureLink status
details
20. Add service.qcdm.modem.device and service.qcdm.modem.interface_number config
options for specifying QCDM/QXDM port for a modem [DAL-2497]
SECURITY FIXES
1. Update to Linux kernel version 5.4.8
2. Removed plain-text passwords displayed in the output of the show config CLI command [DAL2513]
3. Added backo timer when maximum number of SSH/UI login retries is exceeded [DAL-2590]
4. Update to Python version 3.6.10 [DAL-2534]
5. Update tcpdump to version 4.9.3 (CVE-2017-16808 CVE-2018-14468 CVE-2018-14469 CVE-201814470 CVE-2018-14466 CVE-2018-14461 CVE-2018-14462 CVE-2018-14465 CVE-2018-14881 CVE2018-14464 CVE-2018-14463 CVE-2018-14467 CVE-2018-14463 CVE-2018-10103 CVE-2018-10105
CVE-2018-14879 CVE-2018-14880 CVE-2018-16451 CVE-2018-14882 CVE-2018-16227 CVE-201816229 CVE-2018-16301 CVE-2018-16230 CVE-2018-16452 CVE-2018-16300 CVE-2018-16228 CVE2019-15166 CVE-2019-15167) [DAL-2611]
6. Update libpcap to version 1.9.1 [DAL-2611]
7. Update e2fsprogs to version 1.45.5 (CVE-2019-15161 CVE-2019-15162 CVE-2019-15163 CVE-201915164 CVE-2019-15165 CVE-2017-16808) [DAL-2611]
8. Update openvpn to version 2.4.4 (CVE-2017-12166) [DAL-2614]
9. Update libldns to version 1.7.1 (CVE-2017-1000231 CVE-2017-1000232) [DAL-2613]
10. Update libxml2 to version 2.9.10 (CVE-2018-9251 CVE-2018-14567) [DAL-2612]
11. Restrict /etc/config/ to admin-only users [DAL-1396]
96000472_C Release Notes Part Number: 93001322_T Page 17
12. Remove plaintext password from RADIUS debug logs [DAL-2640]
13. Prevent Framebusting JavaScript click-jacking [SEC-494]
14. Prevent users from gaining elevated shell access through custom scripts [DAL-2628]
15. Update libcurl to version 7.69.0 (CVE-2019-15601) [DAL-2732]
16. Update pppd to version 2.4.8 (CVE-2020-8597) [DAL-2732]
17. Fix elevated root access through custom scripts when no-shell is enabled [DAL-2628]
18. Obfuscate sensitive device configuration settings [DAL-1388]
BUG FIXES
1. Connect IT 16/48 only: Fixed timezone oset when saving time to onboard RTC [DAL-2678]
2. Connect IT 16/48 only: Fix bug where devices with an internal realtime clock would not adjust
their local time to the configured timezone [DAL-2272]
3. Fixed bug where SureLinkTM DNS tests took longer than the configured timeout to complete
[DAL-2702]
4. Fixed SSL validation bug preventing modem OTA updates [DAL-2547]
5. Fixed bug where newly-created network Bridges would not be listed as options under the
Device drop-down for network interfaces [DAL-2575]
6. Fixed bug where the primary/active interface was not reported correctly to Digi aView when the
DAL device was configured for load-balancing between two WAN interfaces [DAL-2568]
7. Fixed bug where a device configured with multiple SSH keys would only honor the last SSH key
in the list [DAL-2506]
8. Display the active cellular band for Quectel modems [DAL-2298]
9. Fixed bug where the web UI would display bytes transmitted/received for network interfaces as
N/A [DAL-2295]
10. Fixed bug where the web UI wouldn't show IP information for client devices connected to an
11. OpenVPN server running on the DAL device [DAL-2251]
12. Fix formatting output of show config CLI command when the configuration settings contained
an array [DAL-2594]
13. Fix bug when adding a new element to an array in the config mode of the CLI [DAL-2594]
14. Fix bug where CLI ping and traceroute commands would ignore any interface specified in the
command [DAL-2605]
15. Fix bug where SureLinkTM default tests would continue to pass if cellular modem lost its active
data connection [DAL-2609]
16. Fix a bug handling certificate files with spaces
17. Fixed padding issue with downloading SCEP CA certificates [DAL-2212]
18. Fixed rare issue with passthrough ancillary DNS not resolving if ancillary DNS redirect issue was
disabled
19. Fixed issue with active serial logins when a serial-related configuration change was applied to
the DAL device [DAL-2696]
20. Fixed output of show modem CLI command when cellular modem re-initializes
21. Fix potential initialization issues aer updating firmware [DAL-2762]
VERSION 19.11.72.85 (January 21, 2019)
This is a recommended release.
NEW FEATURES
96000472_C Release Notes Part Number: 93001322_T Page 18
1. Added new digidevice.led python module for controlling LEDs on the device [DAL-2303]
ENHANCEMENTS
2. Include each interface's MTU to the output of the show route verbose command in the Admin
CLI [DAL-2378]
BUG FIXES
Unless otherwise stated, any bugs mentioned here only aect earlier versions of 19.11.x
1. Fixed bug preventing users from configuring an IPsec tunnel with a remote network of 0.0.0.0/0
[DAL-2253]
2. Fixed timing issue between Active Recovery tests and reloading the devices firewall rules, which
if done in the wrong order could result in the device not sending traic through the validated
connection [DAL-2000]
3. Fixed bug where the local web UI would show a *N/A* value for an interface's bytes
transmitted/received [DAL-2295]
VERSION 19.11.72.58 (December 6, 2019)
This is a mandatory release.
NEW FEATURES
1. Re-themed web UI with improved navigation and functionality. New functionality includes:
· The ability to view local filesystem contents [DAL-2110]
· Help-text on login page
· Quick-config access on status pages
· new Dashboard overview page
· Mobile-friendly UI
2. Added new custom page in the web UI for configuring Power Controllers [DAL-2121]
3. New network analyzer and packet capture tool, included in in both the Admin CLI and web UI
[DAL-1575]
4. Added options under the Network->Modem section of the device configuration to setup SIM slot
prioritization and SIM slot failback [DALP-287]
5. Added new Preferred tunnel option under VPN->IPsec->Tunnels to configure a tunnel to be a
primary or failover tunnel [DAL-1478]
6. Add new DHCP Hostname option for IPv4 and IPv6 settings under the Network->Interfaces
section of the configuration to allow the device to advertise its hostname to the DHCP server
upon connection (disabled by default) [DALP-427]
7. Added ability to receive encrypted SMS commands from Digi Remote Manager [DALP-270]
8. Add support for the Telit LM960A18 LTE CAT18 module [DAL-1905]
9. Add support for Sierra Wireless EM7511 LTE CAT18 module [DAL-1414]
10. Add support for Quectel EG25-G LTE CAT4 module [DALP-339]
11. Add support for Quectel EG06 LTE CAT6 module [DALP-403]
12. Add Python support on all products (previously only available on the IX14 and Connect IT 16/48)
[DAL-1907]
13. Add system disable-cryptography Admin CLI command to configure a device for nocrypt mode
[DALP-491]
14. Once a device is set for nocrypt mode, a user must press the Erase button to reset the device to
factory default settings to disable nocrypt mode and restore the device back to standard
96000472_C Release Notes Part Number: 93001322_T Page 19
operation
15. Add show usb Admin CLI command [DAL-2029]
ENHANCEMENTS
1. Connect IT Mini only: Assign new Edge firewall zone to LAN Ethernet port by default to prevent
the device's DNS services from being advertised on the network [DAL-2085]
2. Default user changed from root to admin [DAL-936]. Once a device is upgraded to 19.11.72.58 or
newer firmware
· If you do have an admin user configured, it will not be touched by the update
· If you do not have an admin user configured, a new one will appear. It will have the
same credentials/settings as the root user
· If you had a root user configured (e.g. not factory defaults) it will be preserved to
maintain existing user access
· Restoring the device to factory defaults aer update will result in only the admin user. If
you have a root user and do a factory default, you have to login with the admin user
instead of root, using the same default password printed on the bottom of the device
3. Added the ability to push OpenVPN routes in subnet mode [DAL-2224]
4. Add cellular IMEI and firmware version, along with bluetooth and accelerometer info to show
manufacture command in the Admin CLI [DAL-2030]
5. Add the % measurement value to the CPU usage in the show system output of the Admin CLI
6. Device is passthrough mode with an IPv6 connection now honors and utilizes the MTU in IPv6
RAs
7. When using Verizon SIMs, utilize the OMADM process to auto-discover the APN [DAL-1371]
8. Enhance modem firmware update tool to support multiple modem installations [DAL-2148]
9. Created new Edge firewall zone to prevent the device's DNS services from being advertised on
the network, which still allowing SSH and web UI access [DAL-2085]
10. Removed 192.168.210.254 Default IP gateway [DAL-2095]
11. Added support for sending RFC2136 compatible DNS updates to external DNS servers [DALP446]
12. Add new options under VPN->IPsec->Tunnels->Local endpoint->ID->ID Type for using the
device's MAC address or serial number as its local endpoint ID [DALP-437]
13. Updated the filename of the support report generated through the web UI or CLI to include the
Digi name [DAL-1434]
SECURITY FIXES
1. Updated OpenSSL to version 1.1.1d [DALP-304]
BUG FIXES
4. Fixed bug where Telit LM940 module inside the 1003-CM11 CORE modem could disconnect and
not recover due to it starting up in the wrong mode or its serial ports not responding [DAL-1843]
5. Fixed bug where a device in passthrough mode drops received packets from cellular WAN larger
than its MTU (bug present in firmware versions 19.5.x through 19.8.1.61) [DAL-2137]
6. Fixed bug with timing of RCI callbacks from Digi Remote Manager (bug present in firmware
versions 19.8.1.61 and older) [DAL-2091]
96000472_C Release Notes Part Number: 93001322_T Page 20
7. Fixed bug where RX/TX data usage metrics reported to DRM could be mistakenly calculated as a
negative sum [DAL-1972]
8. Fixed crash in IPsec configuration with more than 6 for IKE Phase 1 proposals or more than 10
IKE Phase 2 proposals [DAL-2066]
9. Fixed bug in reporting the reboot counter metric to DRM [DAL-1932]
10. Fixed bug where persistent system logs could not be remotely accessed through DRM [DAL2060]
11. Fixed bug where DRM would always shows the device's connected method as ethernet [DAL1993]
12. Prevent users from selecting non-production firmware versions when perform modem OTA
updates [DAL-1662]
13. Fixed bug preventing Linux clients from querying a DAL device running a NTP server [DAL-1815]
14. Connect IT 4 and Mini: Fixed bug where early DCD interrupts on a serial port could cause the
device to not boot up [DAL-1873]
VERSION 19.8.1.61 (October 22, 2019)
This is a recommended release.
ENHANCEMENTS
1. Skip auto-APN detection when using Telus SIM cards [DAL-1928]
2. Add QCDM service for accessing QXDM ports of Qualcomm-based modems [DAL-1904]
3. Add microcom tool [DAL-1872]
BUG FIXES
1. Fixed bug in runt where the boot version was reported incorrectly (bug present in firmware
version 19.8.1.43) [DAL-1828]
2. Fixed registration delays on devices with Telit modems using Sprint SIM cards (bug present in
firmware versions 19.8.1.43 and older) [DAL-1872]
3. Fixed stability issues with 1003-CM11 modem (bug present in firmware versions 19.8.1.43 and
older) [DAL-1843]
4. Fixed bug preventing devices using a 1002-CM06 modem (Sierra MC7455) with a Telus SIM from
loading the Telus carrier-firmware onto the modem (bug present in firmware versions 19.8.1.43
and older) [DAL-1823]
5. Fixed memory leak causing a DAL device in passthrough mode to stop responding to ARP
requests on its LAN port (bug present in firmware versions 19.8.1.43 and older) [DAL-1686]
6. Fixed bug preventing SSH keys from being used to authenticate when establishing a SSH
session to the DAL device (bug present in firmware version 19.8.1.43) [DAL-1742]
96000472_C Release Notes Part Number: 93001322_T Page 21
VERSION 19.8.1.43 (August 30, 2019)
This is a mandatory release.
NEW FEATURES
1. Telit LE910c4-NF modem support
2. WAN passthrough, allowing for multi-WAN passthrough setups [DALP-163 & DAL-959]
· As a result, passthrough settings are not under the Modem section anymore, and instead
are by default listed under the Network-Interface->LAN section for devices with
passthrough enabled by default. To change a device defaulting in passthrough mode to
router mode, simply change the "Network->Interfaces->LAN->Interface type" from "IP
Passthrough" to "Ethernet", and then you'll see the normal router-mode configurations
options available.
3. Support for managing network-enabled power strips and power outlets with the powerman
tool [DALP-193]
4. Auto-generated CLI documentation [DAL-1091]
ENHANCEMENTS
1. ModemManager update to version 1.10.2 [DAL-885]
2. Add verbose system log error messages when issues are encountered posting device health
metrics to Digi Remote Manager [DAL-203]
3. Add system log when 1003-CM11 modem (LM940) carrier aggregation is disabled due to
temperature limits
4. Include Telit carrier aggregation details in device support report [DAL-1435]
5. Add support for python RCI/SCI data_service callbacks and requests from Digi Remote Manager
[DAL-1003]
6. Implement protocol to be used for all local communication between cc_acld and connector
clients [DAL-203]
7. Include SIM locked/ready status in show modem CLI output [DAL-1320]
8. Update show modem CLI output formatting to have a summary mode that can be used to
display the status of the modem(s) in the device, and the verbose output to display additional
information for each modem, including the SIM, registration and attachment status [DAL-1184]
8. Improved formatting in the show route CLI output, including finer distinction of static routes
[DAL-1176]
9. Include policy and connection details in show ipsec CLI output, along with improved status
details [DAL-1190 & DAL-1174]
10. Improve labeling in output of the show network interface X CLI command
11. Show OpenVPN client list and rx/tx bytes in show openvpn CLI output [DAL-1192]
12. Add filtering options in show log CLI command [DAL-1181]
13. Add CPU usage, device temperature (if available), device description, and location details in
show system CLI output [DAL-1172]
14. Updated local web UI logout link to list the name of the logged in user [DAL-1142]
15. Renamed the section of central management options from config to cloud [DAL-1255 & DAL1256]
96000472_C Release Notes Part Number: 93001322_T Page 22
16. Added configuration option to have DHCP leases file persistent or clear across reboot [DAL1196]
17. Update CLI table formatting to double space & blank fields [DAL-1186]
18. Add bypass-lan plugin to strongswan to allow 0.0.0.0/0 remote IPSec networks [DAL-1007]
SECURITY FIXES
1. Update Linux kernel to version 5.1.14 [DAL-1076]
2. Busybox update to version 1.31.0 [DAL-1161]
◦ The new busybox shell environment no longer allows local variable statements such as the
following:
▪ local ip_addr='1.2.3.4'
◦ and instead the variable must be set without the local opon, such as:
▪ ip_addr='1.2.3.4'
◦ includes update to httpd webUI
3. Update dnsmasq2 to version 2.80 to address DNS cache snooping (CVE-2017-15107) [DAL-1386]
4. Update conntrack-tools to version 1.4.5
5. Update libnetfilter_conntrack to version 1.0.7
6. Update libmnl to version 1.0.4
7. Update bind to version 9.14.2 [DAL-1338]
8. Update iptables to version 1.8.3
9. Update libqmi to version 1.23.1 [DAL-885]
10. Update libmbim to version 1.18.0 [DAL-885]
11. Update stunnel to version 5.54 [DAL-1162]
12. Update quagga to version 1.2.4 (CVE-2016-1245 and CVE-2017-5495) [DAL-1160]
13. Update tar to version 1.32 [DAL-1159]
14. Add Digi Remote Manager serial port configuration to all DAL products with managed serial
ports (previously only available on Connect IT products) [DAL-1213]
16. Remove unused user passwords from /etc/password [DAL-1316]
BUG FIXES
1. Fixed bug causing loss of cellular connectivity on devices in passthrough mode with IPSec
tunnels built through the cellular passthrough connection (issue present on firmware versions
19.5.x) [DAL-1612]
2. Fixed issue where Connect IT16/48 devices would fail to start up if a 1003-CM modem was
inserted [DAL-1605]
3. Fix issues where Telit QMI modems would disconnect from USB hub and not recover [DAL-1321/
DAL-1556]
4. Fix issues where QMI-based modems would disconnect from cellular network and not
automatically re-attach (bug present in 19.5.x firmware) [DAL-1375]
5. Fix rare issue where Connect IT 4 booted without access to flash
6. Fix issue where logging out of the local web UI from the Terminal page would result in the leside navbar still showing the menu instead of the Log in link [DAL-863]
7. Fix issue where a DHCP relay endpoint couldn't be setup through modem or IPSec interfaces
96000472_C Release Notes Part Number: 93001322_T Page 23
[DAL-956]
8. Close any open sessions on a serial port when configuration update changes the mode of the
serial port
9. Fix bug in show network CLI output when both IPv4 and IPv6 networks were available
10. Fix bug where show network CLI command would show incorrect output when no SIM was
present
11. Fix bug in returning dynamic-only ref_enums in device config to Digi Remote Manager [DAL1323]
12. Fix service serversocket binding when cc_acl restarts [DAL-1411]
13. Fix missing WAN config options in Connect IT 4 devices' default config options
14. Fix reloading of displayed configuration options when enabling/disabling aView central
management in the local web UI [DAL-834]
15. Fix reloading of the Dashboard page when enabling/disabling Intelliflow in the local web UI
[DAL-780]
16. Reset LEDs displayed during reboot instead of freezing the LEDs to show the last known device
state before the reboot [DAL-886]
17. Fix bug where Digi Remote Manager RCI thread blocks indefinitely waiting for config write lock
[DAL-573]
18. Fix bug where ls command in the admin CLI required a terminating / on the path [DAL-1251]
19. Fix bug with show openvpn name CLI command output [DAL-1191 & DAL-1192]
20. Fix bug with carrier, plmn, and modem status output in show modem CLI command
21. Fix column spacing and lower-casing consistency in show arp CLI output [DAL-1173]
22. Fix parsing of carrier names when posting cellular modem details to Digi Remote Manager [DAL1553 & DAL-1326]
23. Limit decimal numbers reported to Digi Remote Manager to six decimal places [DAL-807]
24. Fixed bug with Sierra MC73xx-series cellular modules in 1002-CM03 CORE modems where the
modem would require a power cycle aer upgrading the firmware of the modem in order to
reconnect [DAL-1716]
25. Fixed issue with Telit LE910-NAv2 cellular modules in 1002-CM04 CORE modems not receiving
SMS messages while cellular data session was active/online (bug present on firmware versions
19.8.1.30 and older) [DAL-1634]
26. Add Telus m2m APNs to fallback list [DALP-452]
27. Connect IT 16/48 only: Fix bug causing the device to reset to default settings if the device
experienced a power loss (bug present on firmware versions 19.3 - 19.8.1.30) [DAL-1666]
96000472_C Release Notes Part Number: 93001322_T Page 24
VERSION 19.5.88.81 (June 26, 2019)
This is a mandatory release.
NEW FEATURES
1. Added support for getting NMEA location information from a UDP port (default port 2948) [DAL1084]
SECURITY FIXES
1. Kernel patch for SACK attack (CVE-2019-11477). For more information, see
https://www.digi.com/resources/security
BUG FIXES
1. Fixed bug where IPSec tunnel would cause a system crash when the tunnel was established
over QMI-based modems [DAL-1170]
2. Fixed aView tunnel issue where the tunnel drops over time and remote commands fail [DAL776]
3. Fixed bug preventing QMI-based Telit modems (CAT1 and CAT-M1 modules in particular) from
connecting with vzwstatic APNs (bug present on 19.5.88.59 firmware)
4. Fixed bug where the 1003-CM modem (LTE CAT11 Telit LM940) would shut-down and not
recover its cellular connection if temperatures were too high
5. Fixed bug where the cellular modem occasionally would not initialize properly on devices with a
large number of serial ports
VERSION 19.5.88.59 (May 24, 2019)
This is a mandatory release.
NEW FEATURES
1. New CLI with more commands/consistency [DAL-773]
2. Enable Multicast DNS service on all platforms [DAL-972]
3. Implement RADIUS authentication support for users [DAL-903]
4. Add NTP Server option (disabled by default) [DAL-340]
5. Add sp server to all DAL platforms [DAL-859]
6. ECC Custom Cert Support [DAL-764]
ENHANCEMENTS
1. Improvements to CLI show serial [DAL-1175]
2. Improved reliability of security chip from userspace access due to wakeup
3. Send interface name with cellular status events [DAL-916]
4. Updated ipset version to 7.1 [DAL-917]
5. Update to newest shadow-4.6 package
6. TACACS+ authorization for more server implementations [DAL-933]
7. stunnel updated to version 5.52 [DAL-915]
96000472_C Release Notes Part Number: 93001322_T Page 25
8. Additional health metrics required for DRM 3.0 [DAL-810]
9. Add support for Telit ME910C1_WW
10. Direct remote serial port access via WebUI (shellinabox) [DAL-775]
11. Dual-APN Support on Telit LE910-NAv2 (1002-CM04) [DAL-818]
12. Improved OpenVPN operation and customization [DAL-798]
13. Update to linux-5.0 [DAL-842]
14. Add description field to system group [DAL-581]
15. Upgrade MC7455 to 02.30.01.01 (SWI9X30C 2.0 Release 23) added latest Sierra firmware for
MC7455 and MC7430 [DAL-759]
16. Add an additional APN for Bouygues in France [DAL-840]
17. Improved Telit location reporting [DALP-226]
18. Improved collection of network LINK and Speed reporting
19. Implement Digi Remote Manager health metrics [DAL-707]
20. Added latest Telit LE910_XX_V2 firmware md5 sums
SECURITY FIXES
1. Update to openssl-1.0.2r (security) CVE-2019-1559
2. busybox: fix for CVE-2014-9645 [DAL-1159]
3. busybox: fix for CVE-2017-16544 [DAL-1159]
4. libcurl: update to 7.64.1 (CVE-2017-8816, CVE-2017-8817, CVE-2017-8818, CVE-2018-0500 CVE2018-1000300, CVE-2018- 1000301, CVE-2018-14618, CVE-2018-16839, CVE-2018-16840, CVE2018-16842 CVE-2018-16890, CVE-2019-3822, CVE-2019- 3823)
5. libcurl: fixes for CVE-2018-1000007, CVE-2017-8818, CVE-2017-8816, CVE-2018- 1000005 Zebra
0.99.24: fix for CVE-2016-1245
6. busybox fixes for CVE-2016-6301, CVE-2016-2148, CVE-2017-16544, CVE-2016-2147, CVE- 201715874, CVE-2014-9645, CVE-2011-5325 [DAL-1159]
7. pppd update to 2.4.7 (CVE-2014-3158, CVE-2015-3310)
8. Kernel patch to resolve CVE-2019-11815
BUG FIXES
1. Fix issue on 6300-CX preventing WebUI based firmware update up to 1 in 3 tries [DAL-1194]
2. Remote cloud connections were locked until while long running commands completed [DAL1177]
3. Fix major issue with multiple IPsec policies When two remote subnets are configured in 2
Policies for an IKEv2 tunnel only Policy 2 traic will pass [DAL-934]
4. Corrections to CLI show route [DAL-1176]
5. CLI show system output included outdated current time and uptime [DAL-1172]
6. Errors on console during WebUI firmware update [DAL-1140]
7. Faster fetching of signal attributes for LE910_NA_V2 modem
8. Fixed bug with parsing out MCC/MNC from AT#RFSTS response (LE910NAv2)
9. Fixed cloud connector crash on shutdown
10. Fixed process management issue with cloud connector and configuration
96000472_C Release Notes Part Number: 93001322_T Page 26
11. Check for configured serial ports in show serial command
12. Fixed bug where show serial option is visible for devices with no serial ports [DAL-1114]
13. Web GUI input validation rewording to be consistent
14. DAL-CLI: fix typos in descriptions, titles, and minimums
15. WebUI: Ensure correct versions of static files are loaded (using md5hash)
16. Serial ports were mistakenly listed under Network for metrics and state
17. Metrics had incorrect title, "System" in descriptors/state.
18. ModemManager: Telit error reporting patch
19. Intelliflow crash fix (divide by 0 on some datasets)
20. Intelliflow improve error reporting
21. System maintenance tasks do not run during duration window if reboot time is set [DAL-960]
22. SPIKE: Asynchronous CLI under DRM [URMA-1996]
23. Firmware update through WebUI doesn’t recover when some other page is clicked during the
update process [DAL-869]
24. Signal/dbm/percentage inaccurate on Verizon 2G and 3G connections with MC7354 [DAL-786]
25. Verify and fix dual APN support on the LM940 [DAL-742]
26. Unable to establish dual-APN connection with AT&T using Sierra modem [DAL-813]
27. Telit: Added logic to protect new C1_AP modems from being bricked [DAL-744]
28. Telit: Added firmware check sum for version 414 of LE910-EU1 [DAL-822]
29. Update Telit LE910C1-NS modem firmware from 25.00.244 to 25.00.246 [NPIX-939]
30. Fix MTU support for PPP based connections
31. Added md5 sums for the latest Telit firmware for LE910_NA1
VERSION 19.3.58.59 (March 14, 2019)
· Inial product release
96000472_C Release Notes Part Number: 93001322_T Page 27
Loading...