DICE interface for iPod
for selected Honda/Acura vehicles
Installation Guide/User Manual
Copyrights and Trademarks
Copyright 2008 DICE Electronics, LLC.
The DICE Electronics logo is a trademark of DICE Electronics, LLC.
iPod is a trademark of Apple, Inc.
All rights reserved.
Printed in the U.S.A
2
Table of contents
Copyrights and trademarks 2
Icon legends 3
Warning and safety 4
Product registration 5
Supported iPod models 6
iPod hierarchy 7
Charging 7
Honda R2 integration kit 8-16
Integration kit contents 9
DIP switches 10
DIP switch settings 11
Installation 12
iPod audio source 15
Controls in CDC emulation 15
Operating modes 16
Honda R3/R4 integration kit 17-30
Integration kit contents 18
DIP switches 19
DIP switch settings 20
Installation 21
iPod audio source 24
Controls in CDC emulation 24
Browsing function in CDC emulation 25
Controls in SAT emulation - Non-Nav. radio 26
Controls in SAT emulation - Nav. radio 27
Text display fields 28
Browsing function in SAT emulation 29
Scrolling feature 30
Auxiliary audio source 31
Troubleshooting 33
Disclaimer and warranty 35
Icon legends
Turn jog dial
Turn jog dial repeatedly
Press button
Press button repeatedly
Scroll
3
Warning and safety!
Please read these instructions carefully before proceeding. Failure to follow instructions may result in improper operation
or injury. Neither DICE Electronics, LLC. nor Apple Inc., its regional offices, distributors or resellers take any responsibility for
any damage or injury as a result of using the integration kit.
- Do not open, disassemble or alter the interface in any way.
- Do not insert anything into the casing.
- Do not cut or try to alter cables in any way and always use the correct connections.
- Only operate unit when stationary or ask passengers to operate it for you.
- Do not allow the Apple iPod to distract you from driving.
- Exercise good judgement and keep your eyes on the road at all times.
- Do not expose unit to extreme temperatures, humidity or shock.
- Keep the unit and iPod away from fluids.
- Keep away from children! - Interface components may contain small parts, can be broken or disassembled and
components may become loose from vibration and heat. Small components and packaging materials may be a chocking
hazard when handled by children.
4
Congratulations on your purchase
Thank you for purchasing the DICE integration kit for iPod. Please review our user manual and installation guide before
operating the unit. This interface was designed and manufactured to seamlessly integrate with your vehicle's factory
entertainment system.
Product registration
In order to validate your warranty period and to receive telephone or online support, you MUST register your DICE
product.
To register your DICE product, please complete the following steps:
1. Visit http://www.diceelectronics.com/register
2. Complete the product registration form.
3. Submit the form.
4. Save the registration/support/warranty sheet in a safe place for future reference.
If you are unable to complete the registration via internet, please call DICE Electronics at 1-888-342-3999.
5
Supported iPod models and firmware version requirements
FW:3.1.1
iPod
4th generation
20GB 40GB
FW:1.2.1
iPod
4th generation color display
20GB 30GB 40GB 60GB
FW:1.0.3
iPod classic
80GB 160GB
FW:1.2.1
iPod
5th generation (video)
30GB 60GB 80GB
FW:1.3.1
iPod nano
1st generation
1GB 2GB 4GB
For the latest firmware versions and models not listed, please contact your authorized dealer or DICE Electronics, LLC.
FW:1.4.1
iPod mini
4GB 6GB
FW:1.1.3
iPod nano
2nd generation (aluminum)
2GB 4GB 8GB
FW:1.0.3
FW:1.1.1
iPod nano
3th generation (video)
4GB 8GB
iPod touch
8GB 16GB 32GB
6
iPod hierarchy
By default, the interface creates a Playlist having a name that is the same as the name
of the iPod. This Playlist is the very first on the list of Playlists shown while browsing in
Playlist mode. This Playlist contains all the songs on the iPod. Once a Playlist is active
an Artist may be selected within that Playlist using the Artist Mode. Albums by the
selected Artist and within the selected Playlist may be selected in Album Mode. "ALL
ARTIST" and "ALL ALBUM" designate all available content in those categories.
Charging
The interface automatically charges the battery of the iPod when
connected and the key is in the ACC/ON position.
t
n
e
Playlist
t
n
o
c
e
l
b
a
s
w
o
r
b
s
s
e
L
Artist
Album
M
o
r
e
b
r
o
w
s
a
b
l
e
c
o
n
t
e
n
t
Song
Charging icon will appear
on the upper right corner
of the iPod screen to
indicate charging.
7
Honda R2 integration kit
Integration kit contents
1 Vehicle specific interface unit
1 Vehicle specific harness (R2)
1 iPod docking cable
1 User manual
DICE interface for iPod
for selected Honda/Acura vehicles
Installation Guide/User Manual
9
Dip switches
The configuration switches located on the DICE module are used to set the operation of the interface by the installer.
Incorrect dip switch settings may cause the DICE interface not to work properly or not to operate at all. Disconnect the
vehicle harness from module and cycle ignition off for 50 seconds after changing the switches!
OFF
10
DICE Module
ON 1 2
"Car Config.
Switch"
ON 1 2
"iPod Config.
Switch"
ON
1 2
ON/OFF Switch Positions
Dip switch settings
Car configuration switches
Settings
CD changer (CDC)
Dip switch 1
Dip switch 2
OFF OFF
Switches should remain in the default OFF
position.
OFF OFF
iPod configuration switches
Settings
"Locked" "iPod"
Dip switch 1 Dip switch 2 Dip switch 1 Dip switch 2
OFF OFF ON ON
It is best selected when Text
display is supported by the radio.
After connecting the iPod you will
see the DICE logo on the screen.
After the initialization the iPod will
be locked for an increased
interface functionality.
OFF OFF
DefaultDefault
It is best selected when Text display
is NOT supported by the radio.
Track numbers and times are not
synchronized between the iPod and
radio. Because there is less data
transfer between the iPod and radio,
this mode has the fastest response
time. Content is selected on the
iPod.
ON ON
11
Installation
Installation should only be performed by a qualified professional. Beware of sharp edges to avoid injury and exercise
caution when removing trims as they may break. The module should be placed at an accessible location to allow AUX cable
to be connected, such as in the glove box, the center console or under the front seat.
1 Pull vehicle into service bay.
2 Make sure that the radio code is available before disconnecting battery. Disconnect both battery terminals. These cables
must be disconnected during installation to ensure proper initialization of the module when it is connected.
3 Pull out the radio by removing surrounding trims and screws to access the CD changer connector. Most
trims can be removed by carefully pulling on the piece or using trim removal tools. Trim is usually held in place by
snap-in clips. Consult your dealership if additional information is needed on removing the radio.
12
4 You can access the CD changer connector located on the back of the radio. If the factory CD changer is connected,
unplug it and plug the vehicle specific cable into the receptacle. The connector should securely lock.
Honda R2 BUS connector
Reconnect all the other harnesses as they were if removed. External CD changer cannot be used together with the integration kit.
13
5 Connect the vehicle specific connector and the iPod docking cable to the DICE module. Apply cable ties to secure
the cables.
receptacle receptacle
1/8"
iPod
AUX
dock
input
cable
input
6
Verify that all connections have been properly made.
7 Reconnect the car's battery. est the unit before seating the cables and reinstalling the panels/trim.
vehicle
specific
connector
vehicle specific connectoriPod docking cable
T
14
iPod audio source
Controls in CDC emulation
Press the CD/CDC button to access the interface and its features. Pressing this button repeatedly will cycle through sources
present (internal CD if present, followed by external) in your vehicle. When the iPod audio source is active (DISC 5, Track 1),
use the Track button to select next/previous Song.
Source selector
Press to change
Track, press and
hold it to RW or
FFW.
AMFMCD
VOL
PUSHPWR
TAPE
SEEK
SKIP
DIGITAL AUDIO
COMPACT
discdisc
CDC D -05 T- 01
REW1PLAY/PROG2FF
3
SCAN
CLOCK
RPT
A.SEL
RDM
NR4DISC-5DISC+
H M R
Press to change
DISC.
DISC
TUNE
PUSHMODE
6
15
Operating modes
After connecting the iPod, select the desired browsing mode by selecting the appropriate DISC. To change Track press the
Seek button. The illustration below shows operation with default dip switch settings. When dip switches are set to "iPod"
mode, only Track and Audio source modes are available.
TRACK MODE -
PLAYLIST MODE -
ALBUM MODE -
Album within the
selected Playlist
AUDIOBOOK MODE -
AUDIO SOURCE -
16
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
CDC D -01 T- 03 CDC D -01 T- 06
CDC D -02 T- 15 CDC D -02 T- 18
CDC D -03 T- 25 CDC D -03 T- 28
CDC D -04 T- 02 CDC D -04 T- 05
iPod audio source AUX audio source - see pp.31-32
CDC D -05 T- 01 CDC D -05 T- 02
Honda R3/R4 integration kit
Integration kit contents
1 Vehicle specific interface unit
1Vehicle specific harness (R3 or R4)
1 iPod docking cable
1 User manual
DICE interface for iPod
for selected Honda/Acura vehicles
Installation Guide/User Manual
or
18
(regular harness that is used for
non-nav Honda/Acura and disables
XM (if equipped))
R3 harness R4 harness
(Y-harness required for navigationequipped Honda/Acura and/or to
retain factory XM)
Dip switches
The configuration switches located on the module are used to configure the operation of the interface by the installer.
Incorrect dip switch settings may cause the interface not to work properly or not to operate at all. Disconnect vehicle
harness from module and cycle ignition off for 50 seconds after changing the switches!
OFF
DICE Module
ON 1 2
"Car Config.
Switch"
ON 1 2
"iPod Config.
Switch"
ON
1 2
ON/OFF Switch Positions
19
Dip switch settings
Car configuration switches
Settings
CD changer (CDC) Satellite (SAT)
Dip switch 1
OFF OFF ON ON
Recommended for radios NOT
supporting Satellite (XM) or if
factory SAT is installed and user
wishes to retain it.
Dip switch 2 Dip switch 1 Dip switch 2
Recommended for Satellite (XM)
capable radios. This type of
emulation provides full Text
display on the radio. If Satellite
(XM) is equipped it must be
disconnected to operate flawlessly
in this mode.
iPod configuration switches
Settings
"Locked"
(recommended in SAT emulation)
(recommended in CDC emulation)
"iPod"
Dip switch 1 Dip switch 2 Dip switch 1 Dip switch 2
OFF OFF ON ON
It is best selected when Text
display is supported by the radio.
After connecting the iPod you will
see the DICE logo on the screen.
After the initialization the iPod will
be locked for an increased
interface functionality.
It is best selected when Text display
is NOT supported by the radio.
Track numbers and times are not
synchronized between the iPod and
radio. Because there is less data
transfer between the iPod and radio,
this mode has the fastest response
time. Content is selected on the
iPod.
20
OFF OFF
ON
OFF OFF
Default Default
ON ON ON
Installation
Installation should only be performed by a qualified professional. Beware of sharp edges to avoid injury and exercise
caution when removing trims as they may break. The module should be placed at an accessible location to allow AUX cable
to be connected, such as the glove box, consoles or under the front seats.
1 Pull vehicle into service bay.
2 Make sure that the radio code is available before disconnecting battery. Disconnect both battery terminals. These cables
must be disconnected during installation to ensure proper initialization of the DICE module when it is connected.
3 Pull out the radio by removing surrounding trims and screws to access the CD changer connector. Most
trims can be removed by carefully pulling on the piece or using trim removal tools . Trim is usually held in place by
snap-in clips. Consult your dealership if additional information is needed on removing the radio.
Note that in some vehicles, such as Acura TSX 2004+, you can access the CD changer connector by pulling out the tray located under the
radio.
21
4 You can access the CD changer connector located on the back of the radio.* Unplug the factory connection if present
and plug the Honda R4 BUS connector into the receptacle. Connect the factory plug to the cable receptacle. Make sure
to unplug the factory XM radio tuner located in the trunk area if SAT emulation is selected! The connector should
securely lock.
+
+
+
+
+
+
Honda R4 BUS connector
cable receptacle
* Note that in some vehicles the physical location of the CD changer/SAT connector is on the bottom of the radio.
22
5 Connect the vehicle specific connector and the iPod dock cable to the DICE iPod module. Apply cable ties to secure
the cables.
receptacle receptacle
1/8"
iPod
AUX
dock
input
cable
input
6
Verify that all connections have been properly made.
vehicle
specific
connector
vehicle specific connectoriPod docking cable
7 Reconnect the car's battery. est the unit before seating the cables and reinstalling the panels/trim.
T
23
Controls in CDC emulation
Press the CD/CDC button to access the
interface and its features. Pressing this
button repeatedly will cycle through
sources present (internal CD, followed
by external) in your vehicle. When the
iPod audio source is active (DISC 5,
Track1), use the Seek button to select
next/previous Song.
24
iPod audio source
Source
selector
Press to
change
Track.
AM/FM
C
SEEK
SKIP
/AUXD
AU
T
O
O
CDC
VOL
REW FF PLAY/PROG NR
1 2
F
F
SCAN
D
U L
A
3 4 5 6
VOL
AUDIO
PWR
Press to change
DISC.
1 DISC TRACK
1-01
DISC- DISC+
SOUND
Press to enable
Shuffle Song.
RPT
OD
M E
-
DISP
A.SEL
DR M
TUNE
D
MO E
C
/
A
DICE Silverline browsing function - in CDC emulation
The DICE Silverline integration kit features content browsing. After connecting the iPod, select the desired browsing mode
by selecting the appropriate DISC. Press the Seek button repeatedly to browse contents; 1 second after releasing the
button, your selection is executed. When dip switches are set to "iPod" mode, only Track and Audio source modes are
available.
TRACK MODE -
DISC 1
CDC D -01 T- 03 CDC D -01 T- 06
SEEK
SKIP
PLAYLIST MODE -
ARTIST MODE -
(within the
selected Playlist)
ALBUM MODE -
(within the selected
Artist in the selected Playlist)
AUDIO SOURCE -
DISC 2
DISC 3
DISC 4
DISC 5
CDC D -02 T- 15 CDC D -02 T- 18
CDC D -03 T- 25 CDC D -03 T- 28
CDC D -04 T- 02 CDC D -04 T- 05
iPod audio source
CDC D -05 T- 01 CDC D -05 T- 02
SEEK
SKIP
SEEK
SKIP
SEEK
SKIP
SEEK
SKIP
AUX audio source - see pp.31-32
25
Controls in SAT emulation
Press the SAT button to access the
interface and its features. Pressing this
button repeatedly will cycle through
sources present in your vehicle. When
the iPod audio source is active (Preset 5,
Channel 1), use the Tune button to select
next/previous Song.
Source
selector
AM/FM
SA
SEEK
SKIP
Use Presets to
change modes.
11:53
/
XCD AU
R DT
A IO
CH
PLAYLIST
REW FF PLAY/PROG NR
1 2
SCAN
3 4 5 6
VOL
DISC- DISC+
SOUND
Toggle between
available Text
fields.
TP
R
OD
M E
IS -
D P
A.S LE
RDM
TUNE
Press to
change
Track.
26
Press to enable
Shuffle Song.
AUDIO
PWR
A
UTO
OF
F
D A
U
L
MO
C
A/
Example: Honda/Acura radio without Navigation
DE
Example: Honda/Acura radio with Navigation
AUTO
MODE
OFF
DUAL
Source
selector
Press to enable
Shuffle Song.
XM-1
CH
1
4
MODE SCAN SOUND
MAP/
MENU
GUIDE
LOAD
VOL
PUSH PWR
1
Use Presets to change modes.
:
CHANNEL
CATEGORY
NAME
TITLE
DISC
TAPE
001 - DICE
:
DICE
:
SEL
:
IPOD
2
CH
5
CH
SETUP
INFO
AM/FM
SCAN RPT A.SEL/RDM - SEEK +
2
3 4
CH
CH
ZOOM
CH
CH
AUTO
MODE
A/C
Turn to change
Track.
Press to
change
Track.
Use Presets to
change modes.
VOL
3
6
AUDIO
CANCEL
TUNE
DISP
PUSH SOUND
MODE
DISC+
DISC-
6
5
27
Text display fields - SAT emulation, Non-Navigation radios
Press the DISP-MODE button to cycle through the available Text fields. Note that the display will automatically toggle
between the other Text fields upon a channel change. Select the "- NAME -" Text field to see the mode you are in and select
the "- TITLE -" Text field to view what is playing. In Preset 1, you will always see the Album and Artist information of your
selection in the"- NAME -" Text field and the Song name in the "- TITLE -" Text field. The "- Channel name -" and the "- Category
name -" fields are fixed, except in Preset 6.
11:53
1
RPT
DISP - MODE
CH
- name -
2 sec.
Album * Artist
11:53
CH
RPT
DISP - MODE
28
11:53
CH
Song name
2 sec.
11:53
CH
- TITLE -
DICE Silverline browsing function - SAT emulation
The DICE Silverline integration kit features content browsing. After connecting the iPod, select the desired mode by
pressing Presets 1-6. To change Track press or turn the Tune button repeatedly; 1 second after releasing the button, your
selection is executed. The browsing function below is illustrated in the "- TITLE -" text field.
TRACK MODE -
PLAYLIST MODE -
ARTIST MODE -
(within the
selected Playlist)
ALBUM MODE -
(within the selected
Artist in the selected Playlist)
AUDIO SOURCE -
* Numbers indicate sequence.
1
2
3
4
5
Song name (1)*
PLAYLIST Name (3)
Artist name (25)
album name (5)
iPod audio source
IPOD AUX1
TUNE
TUNE
TUNE
TUNETUNE
TUNETUNE
or
or
or
or
or
Song name (15)
PLAYLIST Name (5)
Artist name (30)
album name (10)
AUX audio source - see pp.31-32
29
Scrolling feature - in SAT emulation, PRESET 6
To set and change scrolling feature go to Preset 6, press the DISP-MODE button repeatedly until you reach the
text field. Change options by pressing or turning the Tune button. After setting the desired feature turn off the
ignition for at least 50 seconds to engage the new selection.
6
Certain amount of blinking is normal on some radios when the scrolling feature is on.
RPT
DISP - MODE
- title -
2 sec.
SHORt stat
TUNETUNE
or
30
"- TITLE -"
SHORT SCROLL
.
.
.
LONG STAT.
.
.
.
LONG SCROLL
Auxiliary audio source
Connections
The interface is equipped with a 1/8” AUX jack connection to connect an auxiliary device, such as an MP3 player, DVD player
or other audio source. To access the AUX audio source, select DISC 5, Track 2 or Preset 5, Channel 2.
Tip (Left audio)
Ring (Right audio)
Sleeve (Ground)
1/8" AUX
1/8" mini stereo jack, not included
input
Making the adjustments
While listening to the auxiliary device, adjust the volume (gain), bass, mid and treble by turning the Tune dial or pressing
the Seek button. DISC/Preset 1-4 modes select what adjustment the Tune/Seek buttons perform. See illustration on page
32.
31
AUX audio source setting
The auxiliary input has settings for gain, bass, mid and treble in order to optimize sound.
Volume (Gain) should be adjusted if the audio level from the auxiliary device is too low or to high. If you hear distorted
audio while playing the auxiliary device, you need to reduce (-) the gain. If you notice that the audio is too quiet then the
gain setting should be increased (+). Default settings are "50" ("68" for gain) and values may be adjusted in increments
between 01-99. Bass, Mid and Treble should be adjusted to compensate for the acoustic presets of the radio.
Note: If you are using an AUX device that is using the vehicle’s power source and not its own battery, you may have to use a
GROUND-LOOP isolator to avoid grounding and engine noise.
32
1
Volume
setting
2 3 4
Bass EQ
setting
Mid EQ
setting
Treble EQ
setting
Troubleshooting
Problem Solution
Cannot select CD changer source.
Cannot select SAT source.
Radio/ steering wheel controls do not operate iPod.
No text display. Make sure DIP switch settings are correctly set for text
Check DIP switch settings (refer to pp.11,20). With the
ignition OFF disconnect vehicle harness from module for a
few seconds and reconnect.
Check DIP switch settings (refer to pp.11,20). With the
ignition OFF disconnect vehicle harness from module for a
few seconds and reconnect.
Reset iPod and make sure most recent iPod firmware is
installed. Check vehicles user manual on how steering
wheel controls work.
display. (Refer to pp.11, 20 for dip switch settings.)
Music is distorted or sound level is too low. Check and make sure all EQ and BASS boost options are
turned off on your iPod. (Refer to AUX settings on p.32)
33
Troubleshooting
No audio from iPod source.
Problem Solution
Reset the iPod.
Certain fields are not displayed on the radio.
iPod does not display the DICE logo when connected.
Sound of factory installed satellite radio is bleeding
through when the iPod audio source is selected.
34
You may have to toggle between the Text fields with the
DISP button.
Reset iPod and make sure most recent iPod firmware is
installed. Make sure all cables are connected properly.
Note that iTouch does not display the logo.
The factory XM module must be disconnected. It is usually
located in the trunk of the vehicle.
Disclaimer and warranty
Important disclaimer, please read!
Unauthorized reproduction or reverse engineering is strictly prohibited! Intellectual property included is distributed under specific license
agreement with respective owners and is licensed only, not sold. No warranty, explicit or implied, is stated. Neither DICE Electronics, LLC., nor
any of its agents, distributors, dealers or vendors shall be liable for damages.
IN NO EVENT SHALL DICE ELECTRONICS' LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE OR ITS
DOCUMENTATION.
Warranty and Support
Products carry a 90 day limited warranty that protects you from defects in material and workmanship of products sold by DICE Electronics, or
its authorized agents, distributors and dealers. a s
be defective during th will be repaired or replaced by at no charge unless warranty is void.
Unauthorized attempt of repair or alteration of the product in any way immediately voids this warranty. Warranty does not extend to
cosmetics or finish.
connected as described in the user manual and all related equipment is functioning properly.
other incurred damages resulting from product defects. Any expenses in the removal and reinstallation of products are not covered by this
warranty.
If experience any problems or need help, please contact your local dealer or call 888-342-3999
http://www.diceelectronics.com/support.
e warranty period either DICE Electronics
A DICE product specialist must determine that defect is present in the product and issue an RMA. Be sure that all wiring is
The warranty period begins the day product is purchased by the end user. Product found to
disclaims any liability for
DICE Electronics
, or visit our support site at
35
Honda/Acura compatible integration for iPod
www.diceelectronics.com
Honda/Acura-iPod 2008-02
Loading...