0
c
-
a
a
y
e
c
e
e
g
h
g
s
0
s
p
w
w
o
D
r
a
n
s
n
t
gg
n
e
e
W
m
gr
g
g
Dialogic® IMG 2
Qui
This document provides a high
for the 2020 IMG. For detailed
documentation at
Before you begin, review the p
are any discrepancies, contact
Locating the Base MAC
The base MAC address is print
the 2020 IMG. The base MAC a
addresses are under software
Use this base MAC address wh
recommend that you obtain th
identification label is similar to
http://www.di
20 Integrated Multimedia G
k Start Installation Guide
level overview of ho w to connect power and
information about installation and setup, refe
logic.com/manuals.
cking list to verify that you received all item
our Dialogic representative.
Address
d on the identification label located on the u
ddress is assigned to the CTRL ports. The oth
ontrol.
n configuring the IP address. Because of its l
base MAC address before you install the sys
this example:
teway
etwork cabling
r to the online
listed. If there
derside rear of
er MAC
ocation, we
em. The
Connecting AC Power
AC power modules must be plu
external groundin
rounding points are for DC sy
AC input power:
• 100 - 240 V AC, 60 - 5
• 115 V AC @ 2 A, or 230
Redundant, hot-swappable AC
Note: When connecting a seco
primary AC power module.
points on t
Connecting DC Power
You must connect the DC 2020
ground to the DC 2020 IMG, u
for earth ground). Dialogic sup
attached to the grounding scre
Caution: Do not dais y-chain t
other equipment or to a comm
DC input power:
• -40 to -60 V DC (-48 V
Redundant, hot-swappable DC
ed into three-prong grounded outlets. Do
e rear of an AC 2020 IMG to ground the syst
tem grounding only.
Hz, 2 A - 1 A
V AC @ 1 A
power modules are located at the rear of the
nd power supply, you do not need to turn off
IMG to earth ground before connecting pow
e 10, 12, or 14 AWG machine tool wire (MT
lies a two-hole #10 solderless crimp groundi
s on the rear of the 2020 IMG.
o or more systems. Do not wire the 2020 IM
n bus bar.
C nominal) @ 6 A
power modules are located at the rear of the
ot use the
m. These
dockin
power to the
r. To connect a
) (green/yellow
n
G directly to
docking station.
station.
lug that is
Warning! You must connect
signaling integrity and to p
the 2020 IMG to a true earth ground to
event elec trical shock . Do not connect
1
aintain
ound to -48 V.
Dialogic® IMG 2020 Integrated Multimedia Gateway Quick Start Ins tallation Guide
Connecting to a Single DC Power Source
To connect a single external DC power source to the 2020 IMG:
1. Turn OFF the existing external power source and disconnect it from the power
supply.
Warning! Failure to turn the power OFF at the source may result in electrical
shock.
2. Attach the wires from the external power source to the DC power module plug.
3. Insert the plug into the DC power module.
4. Reconnect the external power source and turn the power ON.
5. Press the ON button on the front of the server.
Connecting to a Redundant DC Power Source
To connect a redundant DC power source to the 2020 IMG, follow the Connecting to a Single
Power Source procedure.
Note: Do not turn off power to the primary -48 V DC module or the unit will shut down.
DC power cables
A 500 mm DC power pigtail cable is included with DC systems. If you require a longer cable,
the 4 m cable is available for order (P/N BDN-CBL-1000).
Caution: The color specifications for the DC power cables are not identical. Be sure to
review the specifications that are shipped with your cable before installation.
DC power cable (500 mm)
DC power pigtail 4 m cable (P/N BDN-CBL-1000)
2
Loading...