How it Works
Dialight
Loading...
D564-A13-001
User Manual
14 pgs318.38 Kb0

Dialight D564-A13-001 User Manual

Download
Page 1
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
INSTALLATION AND MAINTENANCE MANUAL
FOR
P/N: D564-A13-001
120/240VAC, 50/60 Hz,
L864 RED MEDIUM INTENSITY BEACON
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
1 of 14
Page 2
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Contents Page
List of Figures and Tables .................................................................................2
Reference Drawings ...........................................................................................2
Section 1: Overview............................................................................................3
Section 2: Wiring and Mounting ........................................................................4
Section 3: Operation and Test...........................................................................5
Section 4: Beacon Theory of Operation............................................................5
Section 5: Maintenance and Troubleshooting..................................................6
Section 6: Specifications .................................................................................13
Section 7: Regulatory Compliance and Certifications...................................13
Section 8: How to Obtain Warranty Service ...................................................13
Beacon Wiring Diagram ...................................................................................14
List of Figures and Tables
Figure 1: L-864 Flashing Red Beacon Assembly Figure 2: Base - Bottom view Figure 3: System Block Diagram Figure 4: Beacon – External View Figure 5: Beacon in Open Position Figure 6: Light Engine Install/Removal Table 1: Troubleshooting
Reference Drawings
Beacon Wiring Diagram
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
2 of 14
Page 3
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Section 1: Overview
The Dialight Flashing Red Beacon is designed for the lighting of radio towers, wind generators and other obstructions to aerial navigation, as specified by the FAA, FCC, ICAO and Transport Canada.
The L-864 Flashing Red Beacon as shown in Figure 1, (hereafter referred to as the Beacon) operates from 120 / 240VAC 50/60 Hz. The beacon consists of High Performance LED’s that provide the light output equivalent to an incandescent fixture while consuming a fraction of the electrical power. This manual provides guidance and recommendations for the installation and testing of the beacon assembly. Please read this document in its entirety before installing the Beacon.
Figure 1
L-864 Flashing Red Beacon Assembly
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
3 of 14
Page 4
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Section 2: Wiring and Mounting Warning:
Remove power from all wiring and circuitry before installing or working on the Beacon.
Wiring the Beacon
The Beacon only requires a connection to 120 / 240 VAC, 50/60 Hz power. The ground wire must be connected for proper operation and protection of the Beacon.
Mounting the Beacon
Dialight recommends the installation of one or more lightning rods near the installed Beacon. The lightning rods should extend a minimum of three feet above the height of the Beacon.
The Beacon is mounted to the tower pedestal utilizing customer supplied ½” hardware. Six mounting holes are provided on the Beacon base (Figure 2). These mounting holes will align with most tower pedestals. The Beacon must be installed level according to the bulls-eye level inside the light engine to maintain light output in accordance with FAA requirements.
Figure 2
Base - Bottom View
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
4 of 14
Page 5
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Section 3: Operation and Test
Prior to installation, it is recommended that the unit be tested to ensure no damage was incurred during shipping. This is accomplished by applying power to the beacon. Visual verification of the functioning of the Beacon will indicate proper performance. WARNING: Do not look directly in to LED’s. Adequate eye protection should always be used. NOTE: Beacon is supplied as a steady burn unit and thus will not flash unless other modifications were requested and supplied with the unit.
Upon completion of this test, the installation may proceed.
Section 4: Beacon Theory of Operation
4.0 System Overview
The block diagram in Figure 4 shows the major components of a typical Beacon installation. The parts of the system are the LED Beacon and Controller. The LED Beacon is made up of one LED module, which lights when current passes through it. The LED Beacon contains its own internal power supply. The Beacon is designed for use with an external controller. This external controller provides the properly timed flashing signal, fault monitoring and alarm interfaces.
External
Controller
Figure 3 - System Block Diagram
Power Supply
Beacon Assembly
LED Module
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
5 of 14
Page 6
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
4.1 Lightning Protection
The Beacon incorporates protection against voltage surges (as induced by nearby lightning strikes for example) by means of a multi stage protection circuit utilizing the latest in arresting protective components
Section 5: Maintenance and Troubleshooting
No regularly scheduled maintenance is required for the Beacon. General cleaning of the Dome Assembly should be done using soapy water. No
other cleaning solutions are recommended. Abrasive compounds will scratch the Dome Assembly.
Table 1 Lists possible faults and repair procedures for the L-864 Red Beacon
Table 1 Troubleshooting
Symptom Possible Cause Corrective Action
Beacon does not light No AC power
LED Failure
Power supply Failure
Verify proper AC levels from power source thru supply lines.
Replace LED Module
Replace power supply
Beacon does not flash Refer to controller
documentation supplied by the manufacturer.
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
6 of 14
Page 7
Document No.
Latch
Beacon Dome
Beacon Replacement
Replacement
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Repair and Replacement
Refer to Table 1 for troubleshooting procedures.
and O-Ring assembly D464-2005
Lamp
D564-1011
Gen V Power Supply D564-9000 (Not pictured – inside light engine)
Recommended spare parts, User replaceable parts
Figure 4 Beacon – External View
Description Dialight Part Number
Beacon Replacement Lamp D564-1011
Beacon Dome and O-ring D464-2005
Gen V Power Supply (Inside Light Engine) D564-9000
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
7 of 14
Page 8
Document No.
Terminal Block
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
NOTE: The only parts that are serviceable on the Beacon are the Replacement Lamp and Power Supply.
Procedure for Installing the Replacement Lamp
Step 1 WARNING: Power to the Beacon must be removed prior to servicing. Step 2 Unclamp the two latches holding the lamp down. Step 3 Rotate the lamp back to its open position. Step 4 Disconnect the line and neutral wires from the terminal block, and than
unscrew the grounding strap from the lamp to the base. Be careful not to lose the screw for the ground strap.
Ground Strap
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
8 of 14
Page 9
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Figure 5 – Beacon in Open Position
Step 5 Rotate the lamp downwards to approximately 10 degrees from the
closed position. The key should line up with the keyway on the hinge and allow for the lamp to be pulled off of its pins.
Figure 6 – Lamp Install/Removal Position
Step 6 Slide the new lamp onto the pins to line it up. Rotate it to approximately
10 degrees from closed to again line up the keyway. Push the light engine past the key until it clears and than rotate it back to the open position.
Step 7 Reconnect the line and neutral wires to the terminal block, followed by
the grounding strap.
Step 8 Rotate the lamp down to the closed position and secure the two latches
to complete installation. Apply power to ensure the beacon lights up correctly.
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
9 of 14
Page 10
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Replacement Procedure for the Power Supply
Step 1 WARNING: Power to the Beacon must be removed prior to servicing. Step 2 Unclip 3 tabs holding the dome down and place it out of the way (dome
is tethered to pedestal).
Step 3 Remove 3 Phillips head screws (8-32 x ¼ inch) and accompanying
lockwashers holding the Aluminum cover plate down and place it out of the way. Be careful not to misplace the hardware and cover plate.
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
10 of 14
Page 11
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Step 4 Cut the Black/White AC wires as close to PCB as possible ensuring
ferrite remains unaffected.
Step 5 Cut the Red/Black output wires as close to PCB as possible.
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
11 of 14
Page 12
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Step 6 Remove 4 Phillips head screws (8-32 x ¼ inch) and accompanying
lockwashers holding the power supply down. Remove the existing power supply. Be careful not to misplace the hardware.
Step 7 Install the NEW potted power supply in same orientation as the existing
supply using 4 Phillips head screws (8-32 x ¼ inch) and lockwashers.
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
12 of 14
Page 13
Document No.
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Step 9 Re-connect output and AC wires to the new supply using wire nuts or
another suitable connection.
Step 10 Apply power to ensure the beacon lights up correctly.
Section 6: Specifications
Power Supply Specifications (D564-9000)
Input Voltage Range 120-240VAC at 50/60Hz Nominal Input Power 19W (steady burn) Power Factor >0.9 ATHD <20%
Beacon Specifications
Light Color Red Weight 18 Pounds Height 8.4 Inches Width 15.0 Inches Bolt Hold down Pattern Standard Pattern provided (See Fig. 2)
Section 7: Regulatory Compliance and Certifications
7.1 ETL Certified to: Federal Aviation Administration (FAA): AC No. (150/5345-
43). Refer to website for latest certifications.
Section 8: How to Obtain Warranty Service
Refer to www.dialight.com
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
13 of 14
Page 14
Document No.
Live (Black)
Neutral (White)
Ground (Green)
+Red
9100-127-1733-99 Rev A
June 19, 2013
_____________________________________________________________________
Beacon Wiring Diagram
Power
Supply
LED
Module
-Black
REVISION HISTORY
REV ECO No. DRN CKD APP QA CM DATE
A ---- SA DW JP RL JN 6-19-13
_____________________________________________________________________________
Dialight Corporation 1501 Route 34 South Farmingdale NJ 07727
14 of 14
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use