Page 1
www.d.com
1
Chapter 1 Introduction
KS156-AL
15.6” Touch Panel PC
User’s Manual
A49800902
Preliminary
Page 2
www.d.com
2
Chapter 1 Introduction
Copyright
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2019. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Page 3
www.d.com
3
Chapter 1 Introduction
Table of Contents
Copyright ............................................................................2
Trademarks .........................................................................2
FCC and DOC Statement on Class A ....................................2
About this Manual ...............................................................4
Warranty ...........................................................................4
Static Electricity Precautions ................................................4
Safety Measures..................................................................4
Safety Precautions ..............................................................5
About the Package ..............................................................5
Chapter 1 - Introduction ......................................................6
Overview .................................................................................6
Key Features ...........................................................................6
Specifications ...........................................................................7
Getting to Know the KS156-AL .................................................8
Mechanical Dimensions ............................................................9
Chapter 2 - Getting Started ...............................................10
Chapter 3 - Installing Devices ............................................11
Removing the Chassis Cover ...................................................11
Installing a SATA drive ...........................................................11
Installing an M.2 Card ............................................................12
Installing a Mini PCIe Card .....................................................13
Chapter 4 - Jumper Settings ..............................................14
Clear CMOS Data ................................................................... 14
M.2 Signal Select ................................................................... 15
Backlight Power Select ...........................................................16
Panel Power Select ................................................................16
LCD/Inverter Power Select......................................................17
Chapter 5 - Ports and Connectors ......................................18
Top Panel I/O Ports ...............................................................18
USB Ports ...................................................................................................19
RJ45 LAN Ports ...........................................................................................19
COM (Serial) Ports ......................................................................................20
Graphics Interfaces .....................................................................................21
Audio Output .............................................................................................. 21
I/O Connectors ...................................................................... 22
Serial ATA Connector & Serial ATA Power Connector .....................................22
S/PDIF Connector ...................................................................................... 22
LVDS LCD Panel & Inverter Power Connector ............................................... 23
Digital I/O and Power Connectors ................................................................ 24
Expansion Slots .......................................................................................... 24
Front Panel Connector ................................................................................25
Standby Power LED ....................................................................................25
Battery ....................................................................................................... 26
SMBus Connector ...................................................................................... 26
Chapter 6 - Mounting Options ...........................................29
VESA Mount ..........................................................................29
Panel Mount ..........................................................................30
Chapter 7 - BIOS Setup ....................................................31
Chapter 8 - Supported Software ........................................43
Page 4
www.d.com
4
Chapter 1 Introduction
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Safety Measures
To avoid damages to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Page 5
www.d.com
5
Chapter 1 Introduction
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• One 15.6” Touch Panel PC
• One
sheet of poron foam
• One CD disk includes: Drivers and Manual
Optional Items
• Panel mount kit
• Power Adapter (60W, 12V/5A, Level 6, RoHS)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Safety Precautions
• Use the correct DC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
Page 6
www.d.com
6
Chapter 1 Introduction
Chapter 1 - Introduction
Chapter 1
Overview
KS156-AL
Rear View
Key Features
Model Name KS156-AL
Processor Intel Atom® Processor E3900 Family, BGA 1296
Intel Atom® x5-E3940 Processor
Intel® Pentium® Processor N4200
LAN Two LAN ports
COM Two COM ports (DB-9)
Display VGA and HDMI ports
USB Four USB 3.0 ports (type A)
Audio Line-out jack
Front View
Bottom View
Page 7
www.d.com
7
Chapter 1 Introduction
Specifications
Chapter 1
Note:
*Optional items are not supported in standard model. Please contact your sales representative for more information.
Processor Intel Atom® Processor E3900 Series, BGA 1296
Intel Atom® x5-E3940 Processor, Quad Core, 2M Cache, 1.6GHz (1.8GHz), 9.5W
Intel® Pentium® Processor N4200, Quad Core, 2M Cache, 1.1GHz (2.5GHz), 6W
Memory Two 204-pin SODIMM up to 16GB
Single Channel DDR3L 1867MHz
BIOS Insyde SPI 64Mbit (supports UEFI boot only)
Display and Touch
Screen
• Display: 15.6” 1366x768 TFT LCD Panel with Capacitive / 5-Wire
Resistive Touch Screen
• Brightness: 400 cd/m²
• Contrast: 500:1
• Backlight Lifetime: 50,000 hours
Graphics • Intel® HD Graphics
Display ports: VGA (resolution up to 1920x1200 @ 60Hz) & HDMI
(resolution up to 3840x2160 @ 30Hz)
Supported applications: OpenGL 5.0, DirectX 12, OpenCL 2.1
• Supported Codecs:
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/
H.265, VP8, VP9, MVC
HW Encode: AVC/H.264, JPEG/MJPEG, HEVC/H.265, VP8, VP9, MVC
Storage 1 x 2.5" SATA 3.0 Drive Bay
Expansion 1 x PCIe x1 slot (Gen 2)
1 x M.2 Type (Key B) (PCIe/SATA/USB)
1 x Full-size Mini PCIe (PCIe/USB)
Audio Controller Realtek ALC888 5.1-channel
Ethernet Controller
2 x Intel® I210AT PCIe (10/100/1000Mbps)
Top I/O Ports
2 x Antenna Hole for Wi-Fi or Cell Module
Bottom I/O Ports 2 x GbE (RJ-45) (10/100/1000Mbps)
2 x RS-232/422/485 (DB-9)
4 x USB 3.0 (type A)
1 x VGA
1 x HDMI
1 x Line-out
1 x Power Button
Watchdog Timer System Reset, Programmable via Software from 1 to 255 Seconds
Power Two Types: 12V DC or 15V - 36V DC
OS Support
(UEFI ONLY)
Windows 10 (64-bit)
Yocto Project
Fedora 24 (Intel Graphics Driver available)
Ubuntu 16.04 (Intel Graphics Driver available)
Mechanism Construction: sheet metal
IP Rating: IP65 front panel protection
Mounting: VESA/panel mount (*)
Weight: TBD
Dimensions (W x H x D): 412.1 mm x 261.4 mm x 63 mm
Environment Operating Temperature: 0 to 50°C
Storage Temperature: -30 to 70°C
Relative Humidity: 5 to 85% RH (non-condensing)
Tests and
Certication
Shock:
OP: Half-sine, 3G @ 11ms
Non-OP: Half-sine, 5G @ 11ms
Vibration:
OP: Random, 1Grms @ 5~500Hz, 30min
Non-OP: Sweep sine, 3Grms @ 10~500Hz, 30min
Page 8
www.d.com
8
Chapter 1 Introduction
Getting to Know the KS156-AL
Chapter 1
Bottom View
Rear View
Power Button
Press to power on or power off the system.
COM Ports
Connect RS232, RS422 or RS485 devices.
LAN Ports
Connect a network device or a Ethernet cable from a LAN for network connectivity.
USB 3.0 Ports
Connect USB 3.0 devices as well as devices from previous versions such as USB 2.0
or USB 1.1.
Line-out Port
Connects a speaker.
VGA Port
Connects the VGA port of a display.
HDMI Port
Connects the HDMI port of a display.
DC-in Jack
Connects the DC-in power adapter.
Power Button
HDMI
COM 1
(RS232/RS422/RS485)
COM 2
(RS232/RS422/RS485)
USB 3.0
VGA
LAN1 LAN2
Line-out
DC-in
Page 9
www.d.com
9
Chapter 1 Introduction
409.60
259.90
185.60
6
272.20
54
Chapter 1
Mechanical Dimensions
Bottom View
Top View
Right ViewLeft View
Front View
Page 10
www.d.com
10
Chapter 2 Getting Started
Chapter 2 - Getting Started
Chapter 2
Preparing the System
Before you start using the system, you need the following items:
• SATA HDD/SSD
• Power adapter or other means of power supply
• AC power adapter
Installing Devices
The following devices can be installed in the system.
• Mini PCIe cards
• M.2 cards
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1. Power on the system.
2. After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing an Operating System
Depending on the method you choose to install your system, you may use a USB flash drive
or install a CD-ROM drive to run the Operating System CD.
Make sure that a SATA drive or an M.2 card is already installed.
1. Refer to the following chapters for information on installing a SATA drive or an M.2 card.
2. Refer to your operating system manual for instructions on installing an operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
Page 11
www.d.com
11
Chapter 3 Installing Devices
Chapter 3
Removing the Chassis Cover
Chapter 3 - Installing Devices
1. Make sure the system and all other peripheral devices connected to it have been powered off.
2. Disconnect all power cords and cables.
3. The 6 mounting screws on the rear chassis are used to secure the cover to the system.
Remove these screws and put them in a safe place for later use.
Screws
4. Lift the cover up to open the system.
5. The
SODIMM,
Mini PCIe and the M.2 sockets are readily accessible after removing the
chassis cover.
SODIMM Slot
Mini PCIe Slot
M.2 Socket
Installing a SATA drive
1. Uninstall the SATA mount bracket from the system. Align the mounting holes of the SATA
drive with the mounting holes on the SATA mount bracket and use the provided mounting
screws to attach the SATA drive to the bracket.
The system can accommondate one 2.5-inch SATA drive. Please use the following procedure to
install a SATA drive.
Mounting screw
2. Connect one end of the SATA cable to the SATA power and data connectors on the SATA
drive and the other end of the SATA cable to the SATA power and data connectors on the
system board.
3. Align the mounting holes of the SATA mount bracket with the mounting holes on the system
and use the provided mounting screws to secure the SATA mount bracket in place.
SATA connectors
SATA power/data cable
SATA mount screws
Note:
The SATA Port 1 shares the bandwidth with the M.2 slot. To assign the SATA signal to
SATA Port 1 or the M.2 slot, refer to Chapter 4.
Page 12
www.d.com
12
Chapter 3 Installing Devices
Chapter 3
Installing an M.2 Card
2. Align the notch at the edge of the M.2 card with the key in the connector.
3. Insert the M.2 card into the connector.
Note:
The M.2 socket supports PCIe, USB, and SATA signals and can accommodate
commonmobile broadband and storage modules. For jumper settings on switching the
signal betwen SATA and PCIe, refer to Chapter 4.
The system is equipped with one M.2 socket, supporting both the M.2 22x42mm and 22x80mm
(key B) form factors. Use the following procedure to install an M.2 card:
1. To install an M.2 type 2242 card, please install the standoff at the 42mm mounting
position rst.
M.2 mount standoff
M.2 Type 2280 Socket
M.2 Type 2242 Socket
M.2 card
4. Push down on the other end of the M.2 card and secure the card on the mainboard with
the provided mounting screw.
M.2 card
Mounting screw
Page 13
www.d.com
13
Chapter 3 Installing Devices
Chapter 3
Installing a Mini PCIe Card
The system board is equipped with one Mini PCIe slot that supports PCIe and USB signals. Use
the following procedure to install a Mini PCIe card:
1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card
with the key in the connector on the system board.
Mini PCIe card
2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on
the system board. Route the antenna cables underneath the SATA bracket to the reach the
antenna holes on the side panel.
Mounting screw
Page 14
www.d.com
14
Chapter 4
Chapter 4 Jumper Settings
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Clear CMOS Data
JP6
You can reconfigure the system with the default values stored in the ROM BIOS if you encounter the following situations:
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper back to its
default setting, pins 1 and 2 On.
3. Now plug the power cord and power on the system.
Chapter 4 - Jumper Settings
JP3 is used to select the PCIe signal for either the PCIE1 slot (default) or the
M.2 (key B) connector.
1-2 On:
Normal (default)
3 12
2-3 On:
Clear CMOS Data
3 12
PCIE1/M.2 (Key B) PCIE Signal Select
JP3
2-3, 5-6, 8-9, 11-12 On:
M.2 key B PCIe
1-2, 4-5, 7-8, 10-11 On:
PCIE1 (default)
1
12
10
1
12
10
Page 15
www.d.com
15
Chapter 4
Chapter 4 Jumper Settings
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
JP4
SATA 1/M.2 (Key B) SATA Signal Select
JP4 is used to select the SATA signal for either the SATA 1 port (default) or the
M.2 (key B) connector.
M.2 Signal Select
JP1 is used to select the signal for the M.2 connector: SATA (default) or PCIe.
1-2, 4-5, 7-8, 10-11 On:
SATA 1 (default)
3
1
12
10
2-3, 5-6, 8-9, 11-12 On:
M.2 (key B) SATA
3
1
12
10
2-3 On:
PCIe
1
3
2
1-2 On:
SATA (default)
1
3
2
JP1
Page 16
www.d.com
16
Chapter 4
Chapter 4 Jumper Settings
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Panel Power Select
JP8 is used to select the power supplied with the LCD panel.
Important:
Please do not alter this jumper’s setting if you do not know the LCD panel’s power
specification. Selecting the incorrect voltage will seriously damage the LCD panel.
JP8
Backlight Power Select
JP9 is used to select the power level of backlight brightness control: +5V or +3.3V (default).
Important:
Please do not alter this jumper’s setting if you do not know the power specification of
the backlight. Selecting the incorrect voltage will seriously damage the backlight.
JP9
2-3 On:
+5V
3 12
1-2 On:
+3.3V (default)
3
12
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
5-6 On:
+3.3V
5
2
4
6
1
3
3-4 On:
+5V (default)
5
2
4
6
1 3
1-2 On:
+12V
5
2
4
6
1
3
Page 17
www.d.com
17
Chapter 4
Chapter 4 Jumper Settings
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
LCD/Inverter Power Select
JP10
JP10 is used to select the power level of the LCD inverter connector.
1-2 On:
+12V (default)
13 2
2-3 On:
+5V
13
2
COM1/COM2 RS232 Power Select
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
JP2 (for COM 1) and JP5 (for COM 2) are used to configure serial ports to pure RS232 or
RS232 with power. The pin assignments of COM 1 and COM 2 will vary according to JP2’s and
JP5’s setting respectively.
JP2
JP5
JP2 (for COM 1), JP5 (for COM 2)
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
6
4 2
5
3
1
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
6 4
2
5
3 1
Pin RS232 RS232 with power
1
DCD +12V
2
RXD RXD
3
TXD TXD
4
DTR DTR
5
GND GND
6
DSR DSR
7
RTS RTS
8
CTS CTS
9
RI +5V
Page 18
18
Chapter 5
Chapter 5 Ports and Connectors
Top Panel I/O Ports
Chapter 5 - Ports and Connectors
The top panel I/O consists of the following ports and connectors:
• COM ports:
COM 1 and COM 2 can be an RS232, RS422 or RS485 port.
• USB ports:
Four USB 3.0 ports.
• LAN ports:
Two LAN ports for Ethernet connectivity.
• Display ports:
One VGA and one HDMI port for display output.
• Line-out Port:
One line-out port for audio output.
• DC-in Jack
Connects the DC-in power adapter.
Power Button
HDMI
COM 1
(RS232/RS422/RS485)
COM 2
(RS232/RS422/RS485)
USB 3.0
VGA
LAN1 LAN2
Line-out
DC-in
12V or 15~36V DC-in
This jack is considered a low power solution. There are two variants of the power input for
different SKUs: 12V or 15~36V DC-in. Connect a DC power cord to this jack. Using a voltage
more than the recommended range may fail to boot the system or cause damage to the system board.
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
DC-in
Automatic power-on
The system can be powered on automatically when power supply comes in or when power supply
resumes after a power loss event. Configure the automatic power-on function in the Advanced
menu (“ACPI Configuration” submenu) of the BIOS. Refer to Chapter 7 for more information.
Page 19
19
Chapter 5
Chapter 5 Ports and Connectors
USB Ports
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with four onboard USB 3.0 ports (USB 0-1/2-4) on the bottom
panel. The two 10-pin connectors allow you to connect 4 additional USB 2.0 ports (USB 4-5/6-
7). The 5-pin connector allows you to connect 1 additional USB 2.0 port (USB 8). These additional USB ports may be used for testing or future expansion.
Wake-On-USB Keyboard/Mouse (optional)
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
RJ45 LAN Ports
Features
• 2 Intel® I210AT PCI Express Gigabit Ethernet controllers
The LAN ports allow the system to connect to a local area network for Ethernet connectivity.
BIOS Setting
Configure the onboard LAN in the Advanced menu (“ACPI Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 8 for more information.
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
LAN 1
LAN 2
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
USB 1
USB 3.0
USB 0
USB 4
USB 3.0
USB 2
USB 6-7
USB 4-5
USB 8
USB 2.0
1
5
GND
-Data0
+Data0
VCC
USB 2.0
NC
10
VCC
-Data0
+Data0
GND
VCC
-Data1
+Data1
GND
NC
9
1
2
Page 20
20
Chapter 5
Chapter 5 Ports and Connectors
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
COM (Serial) Ports
COM 1 and COM 2 can be selected among RS232, RS422 and RS485.
COM 3 to COM 6 are fixed at RS232.
The pin assignments of COM 1 and COM 2 ports will vary according to JP2’s and JP5’s
setting respectively. JP2 and JP5 are used to configure COM port 1 and COM port 2
to pure RS232 or RS232 with power. Refer to “COM 1/COM 2 RS232/Power Select“ in
Chapter 4 for more information.
Please use the BIOS setup utility to congure serial port communication mode for COM 1
and COM 2.
BIOS Setting
Configure the serial ports including the serial communication mode in the Advanced
Configuration (“Super I/O Configuration” submenu) of the BIOS. Refer to Chapter 7 for
more information.
COM Port Connector
RS422
Full Duplex
RS485
RS232
RTS
RI
DSR
CTS
6 7 8 9
DCD
(or +12V)
TXD
RXD
DTR
GND
1
2 3 4 5
RX+
TX+
RX-
TX-
GND
1 2 3 4 5
6 7 8 9
N.C.
N.C.
N.C.
N.C.
DATA+
DATA-
1 2 3 4 5
GND
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
6 7 8 9
COM 1 (RS232/422/485) / COM 2 (RS232/422/485)
COM 2
COM 1
COM 3/ COM 4 /COM 5 /COM 6
(or +5V)
Page 21
21
Chapter 5
Chapter 5 Ports and Connectors
Graphics Interfaces
The display ports consist of the following:
• 1 VGA port
• HDMI port
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to secure the connector in place.
HDMI Port
The HDMI port, which carries both digital audio and video signals, is used to connect the
HDMI port of an LCD monitor or digital TV.
BIOS Setting
Configure these onboard graphics devices in the Advanced menu (“Video Configuration” submenu) of the BIOS. Refer to Chapter 7 for more information.
Driver Installation
Install the graphics driver. Refer to Chapter 8 for more information.
Audio Output
Front Audio
The front audio connector allows you to connect a second line-out and microphone jacks.
Line-out (lime)
This jack is used to connect a headphone or external speakers.
BIOS Setting
Configure these onboard audio devices in the Advanced menu (“Audio Configuration” submenu) of the BIOS. Refer to Chapter 7 for more information.
Driver Installation
Install the Realtek ALC888 audio drivers. Refer to Chapter 8 for more information.
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Line-out
Front Audio
1
Mic-L
Line-R
GND
GND
NC
2
10
Mic-JD
Line-JD
9
Mic-R
Line-L
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
222 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
VGA
VGA HDMI
HDMI
Page 22
22
Chapter 5
Chapter 5 Ports and Connectors
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
I/O Connectors
Serial ATA Connector & Serial ATA Power Connector
Features
7
RXN
GND
TXP
TXN
GND
1
RXP
GND
SATA 3.0
• 2 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s (SATA 0 and SATA 1)
• Integrated Advanced Host Controller Interface (AHCI) controller
The Serial ATA connectors are used to connect Serial ATA devices; the SATA power connectors supply power to the SATA drives. Connect one end of the SATA cable to the SATA power
and data connectors on the SATA drive and the other end of the SATA cable to the SATA
power and data connectors on the system board
BIOS Setting
Configure the Serial ATA drive in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
S/PDIF Connector
The S/PDIF connector is used to connect an external S/PDIF port. Make sure pin 1 of the
audio cable is aligned with pin 1 of the S/PDIF connector.
+12V
+5V
Ground
1
Ground
4
SATA 0
SATA 1
SATA
Power 0
SATA
Power 1
1
5
+5V
SPOUT
Ground
SPIN
Page 23
23
Chapter 5
Chapter 5 Ports and Connectors
LVDS LCD Panel & Inverter Power Connector
The LCD/Inverter Power and LVDS LCD Panel are connected to the LCD panel of the system.
Refer to the right side for the pin functions of these connectors.
Jumper Settings
Refer to Chapter 4 Jumper Settings for settings relevant to the LCD panel.
BIOS Setting
Configure the LCD panel in the Advanced menu (“Video Configuration” submenu) of the BIOS.
Refer to Chapter 7 for more information.
Pins Function Pins Function
1
GND
2
GND
3
LVDS_Out3+ (Odd_3+)
4
LVDS_Out7+ (Even_3+)
5
LVDS_Out3- (Odd_3-)
6
LVDS_Out7- (Even_3-)
7
GND
8
GND
9
LVDS_Out2+ (Odd_2+)
10
LVDS_Out6+ (Even_2+)
11
LVDS_Out2- (Odd_2-)
12
LVDS_Out6- (Even_2-)
13
GND
14
GND
15
LVDS_Out1+ (Odd_1+)
16
LVDS_Out5+ (Even_1+)
17
LVDS_Out1- (Odd_1-)
18
LVDS_Out5- (Even_1-)
19
GND
20
GND
21
LVDS_Out0+ (Odd_0+)
22
LVDS_Out4+ (Even_0+)
23
LVDS_Out0- (Odd_0-)
24
LVDS_Out4- (Even_0-)
25
GND
26
GND
27
LVDS_CLK1+ (Odd_CLK+)
28
LVDS_CLK2+ (Even_CLK+)
29
LVDS_CLK1- (Odd_CLK-)
30
LVDS_CLK2- (Even_CLK-)
31
GND
32
GND
33
DDC_CLK
34
N.C.
35
DDC_DATA
36
+3.3V
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
Pins Function
1
GND
2
GND
3
Panel Inverter Brightness
Voltage Control
4
Panel Power
5
+3.3V
6
Panel Backlight On/Off Control
7
+12V (default)/+5V
8
+12V (default)/+5V
LVDS LCD Panel Connector LCD/Inverter Power Connector
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
3940
1
2
8
1
LCD/Inverter Power
LVDS LCD Panel
Page 24
24
Chapter 5
Chapter 5 Ports and Connectors
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Digital I/O and Power Connectors Expansion Slots
M.2
(PCIe 2.0 x1/
USB 2.0/
SATA 3.0)
Digital I/O
The 8-bit Digital I/O connector provides monitoring and control function to external devices
connected to the connector.
Pins Function
1
DIO7
2
DIO6
3
DIO5
4
DIO4
5
DIO3
6
DIO2
7
DIO1
8
DIO0
Digital I/O Connector
M.2 Slot
The M.2 slot on the top side of the system board is used to install M.2 (NGFF) modules. The
socket supports both M.2 Type 2242 and
2280
(Key B) form factors and can be inserted with
either a SATA SSD card or a PCIe NVMe card. Please note that the PCIe Gen 2.0 x1 bandwidth
is capable of up to 500MB/s transfer speed whereas the SATA 3.0 can provide up to 600MB/s
transfer speed. To switch between PCIe and SATA signals for the M.2 slot, refer to Chapter 4
Jumper Settings.
PCI Express Slot (Gen 2.0 x1)
Install a PCI Express card such as network cards that comply to the PCI Express specifications
into the PCI Express x1 (Gen 2.0) slot.
Mini PCI Express Slot
The Mini PCIe socket is used to install a Mini PCIe card to provide the system’s with wireless
communications capability.
Full-size Mni PCIe
(PCIe/USB)
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
8
1
Digital I/O
Power
1
+5V
+12V
5VSB
Ground
4
PCI Express x1
Page 25
25
Chapter 5
Chapter 5 Ports and Connectors
Front Panel Connector
HDD_LED - HDD LED
This LED will be lit when the hard drive is being accessed.
RESET_SW - Reset Switch
This switch allows you to reboot the system without having to power it off first.
PWR_BTN - Power Button
This switch is used to power on or off the system.
SUS_LED - Status LED
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
Pin Pin Assignment Pin Pin Assignment
HDD_LED
3 3V3
PWR_BTN
8 GND
5
HDD_LED
10
Power_Button
RESET_SW
7
GND
SUS_LED
2 3V3SB
9
Reset
4
3V3SB
11
NC
6
Power_LED
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
222 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Front
Panel
Standby Power LED
This LED will be red when the system is in the standby mode. It indicates that there is power
on the system board. Power off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
222 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Standby Power LED
HDD_LED
RESET_SW
SUS_LED
PWR_BTN
11
12
2 1
Page 26
26
Chapter 5
Chapter 5 Ports and Connectors
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Battery
Connect to the battery connector
Battery
Battery
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
SMBus Connector
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and act as a master
by initiating data transfer.
SMBus
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
SMBus_Data
GND
3V3SB
SMBus_Clock
SMBus_Alert
12
5
1
+3.3V
GND
2
Page 27
27
Chapter 5
Chapter 5 Ports and Connectors
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Chassis Intrusion Connector
The board supports the chassis intrusion detection function. Connect the chassis intrusion sensor cable from the chassis to this connector. When the system’s power is on and chassis intrusion occurs, an alarm will sound. When the system’s power is off and chassis intrusion occurs,
the alarm will sound only after the system restarts.
BIOS Setting
Configure the chassis intrusion detection (or case open) function in the Advanced menu (“Super I/O Configuration” submenu) of the BIOS. Refer to Chapter 7 for more information.
1 2
Ground
Signal
Chassis
Intrusion
The LPC connector is used for the debug function and its pin functions are listed below.
LPC Connector
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
LPC
Pin Function Pin Function
1
L_CLK
2
L_AD1
3
L_RST#
4
L_AD0
5
L_FRAME#
6
3.3V
7
L_AD3
8
GND
9
L_AD2
10
---
11
INT_SERIRQ
12
GND
13
5VSB
14
5V
2
1
14
13
Page 28
28
Chapter 5
Chapter 5 Ports and Connectors
The fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
BIOS Setting
The Advanced menu (“Super IO” submenu) of the BIOS will display the current speed of the
cooling fans. Refer to the Chapter 7 for more information.
1
3
FAN IN
12V
Ground
System Fan 1/2
Cooling Fan Connectors
Buzzer
S/PDIF
1
eDP (optional)
29
30
2
1
1
2-
(JP9)
(JP10)
1
1
1
COM 6
9
6
1
6
1
COM 1
9
1
1
199
1 1
9
9
COM 5
COM 4
COM 3COM 2
Nuvoton
6116D
Standby
Power LED
1
SATA 0
1
4
1
SATA 1
SATA 3.0
1
4
USB 8
1
102
USB 6/7
1
102
USB 4/5
5 1
USB 2.0
PTN
3460
Mini PCIe
5
2
5
2
2
5
2
2
2 2
2
3
3
(JP8)
9
9
USB 0/1
USB 3.0
1
10
9
2
Front Audio
Realtek
ALC262-VC2-GR
M.2 B Key
Battery
Clear CMOS Data (JP6)
1
1
1
Intel
Atom
1
1
PCIE1/M.2 B Key PCIE
Signal Select (JP3)
12
SATA 1/M.2 B Key SATA
Signal Select (JP4)
M.2 Signal
Select (JP1)
1
12
1
Chassis Intrusion
2
3 33
10
10
8
33
2
3
VGA
Chrontel
CH7517
LAN 1
LAN 2
Line-out
HDMI
USB 2/4
USB 3.0
Asmedia
ASM1442
DDR3L_1 SODIMM
DDR3L_2 SODIMM
Intel I210AT
Intel
I211AT or
I210IT
DC-in
LAN 1
LAN 2
Line-out
PCIE1 (PCIe x1)
LPC
1
14
11
SPI Flash
BIOS
1
1
5
SMBus
2
11
1
5
6
COM 1 RS232/Power
Select (JP2)
COM 2 RS232/Power Select
(JP5)
SATA Power 0
1
LCD/
Inverter
Power
2
40
1
39
SATA Power 1
LVDS Panel Power Select
(JP8)
LVDS Backlight Power
Select (JP9)
LCD/Inverter Power Select
(JP10)
LVDS LCD Panel
PTN 3460
Front Panel
Digital I/O Power
Digital I/O
System
Fan 1
System
Fan 2
8
2
4
2
13
Page 29
www.d.com
29
Chapter 6 Mounting Options
Chapter 6
Chapter 6 - Mounting Options
VESA Mount
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
VESA mount bracket 1
The VESA mount kit includes the following:
• 2 VESA mount brackets
• Bracket screws
Please use the following procedure to mount your system:
1. Select a place on the wall where you will mount the Panel PC.
2. Use the provided mounting screws to attach “VESA mount bracket 1” to the wall.
3. Attach the other bracket (VESA mount bracket 2) to the rear of the Panel PC.
VESA mount bracket 1
Mounting screw
VESA mount bracket 2
4. Slide the Panel PC to "VESA mount bracket 1" to attach the two brackets with the hooks.
Then tighten the screw to secure the assembly in place.
Screw
Hooks
Mounting screw
VESA mount bracket 2
Page 30
www.d.com
30
Chapter 6 Mounting Options
Chapter 6
Panel Mount
The panel mount kit includes the following:
• 10 mounting clamps
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
Please use the following procedure to mount your system:
1. Select a place on the panel (or wall) where you will mount the Panel PC.
2. Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (396.2mm
x 246.5mm) and ensure that the Panel PC can be tted into the panel properly.
Front view
396.20
246.50
R10.90
Panel
Mounting hole
3. Insert the Panel PC from the outside surface of the panel into the mounting hole until it is
properly tted against the panel.
4. Position the mounting clamps along the rear edges of the Panel PC and insert them into the
slits around the Panel PC.
Slit for mounting the clamp
Mounting clamp
at top
5. The rst and second clamps must be positioned and secured diagonally prior to mounting
the rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing
the white plastic cap onto the back of the panel. The illustration below shows that all
clamps are properly mounted.
272.30
422
16 (x10)
Rear view
Page 31
31
www.d.comChapter 7 BIOS Setup
Chapter 7
Chapter 7 - BIOS Setup
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your
system configuration.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Legends
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Submenu
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
Keys Function
Right and Left arrows
Move the highlight left or right to select a menu.
Up and Down arrows
Move the hightlight up or down between submenu or elds.
<Esc>
Exit the BIOS Setup Utility.
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup defaults
<F10>
Save and exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Page 32
32
www.d.comChapter 7 BIOS Setup
Chapter 7
Main
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Insyde BIOS Setup Utility Advanced
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1980 to 2099.
Page 33
33
www.d.comChapter 7 BIOS Setup
Chapter 7
ACPI Configuration
This section configures system ACPI parameters.
Wake on LAN
Enable or disable WOL (wake-on-LAN) to wake the system through an Ethernet adapter.
After G3
Specify which state the system should be in when power is re-applied after a power
failure (G3, the mechanical-off, state). This option can also serve as the automatic
power-on function.
Always On The system is powered on.
Always Off The system is powered off.
CPU Configuration
This section configures the CPU.
EIST
Enable or disable the Enhanced Intel® SpeedStep® Technology, which helps optimize
the balance between system’s power consumption and performance. After it is enabled
in the BIOS, you can take advantage of its offering by setting power schemes from the
operating system’s power options.
Turbo Mode
Enable or disable processor turbo mode, which allows the processor core to automatically run faster than the base frequency.
C-States
Enable or disable CPU power management. It allows the CPU to go to C states when
it’s not 100% utilized.
Page 34
34
www.d.comChapter 7 BIOS Setup
Chapter 7
Video Configuration
This section configures the video settings.
Primary Display
Select the primary display for the system from the following options:
IGD: integrated graphics devices
PCIe: PCIe graphics devices
Integrated Graphics Device
Enable, disable or automatically detect the integrated graphics device.
PTN3460 Function
Enable or disable the PTN3460 LCD features. If enabled, the LCD panel type and the
panel color depth options will be shown.
Audio Configuration
This section configures the audio settings.
Audio Controller
Control the detection of the high-definition audio devices.
Disabled
High-definition audio devices will be unconditionally disabled.
Enabled
High-definition audio devices will be unconditionally enabled.
Page 35
35
www.d.comChapter 7 BIOS Setup
Chapter 7
SATA Controller
Enable or disable the Serial ATA controller.
SATA Configuration
This section configures SATA devices. It also shows the information about the installed
SATA drives.
SATA Speed
Select Serial ATA device speed from these options: Gen1 (1.5 Gbit/s), Gen2 (3 Gbit/s) or Gen
3 (6 Gbit/s).
SATA Mode Selection
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
Serial ATA Port 0 and 1 and Hot Plug
Enable or disable each Serial ATA port and its hot plug function.
Page 36
36
www.d.comChapter 7 BIOS Setup
Chapter 7
PCI Express Configuration
This section configures the settings of PCI Express root ports.
PCI Express Root Port 1
Controls the PCIe signal of LAN port 2.
PCI Express Root Port 3
Controls the PCIe signal of PCIE 1.
PCI Express Root Port 4
Controls the PCIe signal of LAN Port 1.
PCI Express Root Port 5
Controls the PCIe signal of Mini PCIe slot.
Press “Enter” to enter the configurations for each PCIe root port as shown on the
next page.
PCI Express Root Port
Enable or disable each PCI Express root port.
Hot Plug
Enable or disable the hot plug function.
PCIe Speed
Select the speed of the PCI Express Root Port: Auto, Gen1 (2.5 GT/s) or Gen2 (5 GT/s).
Page 37
37
www.d.comChapter 7 BIOS Setup
Chapter 7
Console Redirection
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
Console Serial Redirect
Enable or disable the console redirection function. (The default is disabled.) If you
select to enable it, please configure the following parameters for serial communication
between the system and a remote station:
Terminal type: VT_100, VT_100+, VT_UTF8, or PC_ANSI.
Baud rate: 115200, 57600, 38400, 19200, or 9600.
Data bits: 8 bits or 7 bits.
Parity: None, Even or Odd.
Stop bits: 1 bit or 2 bits.
Flow control: None, RTS/CTS or XON/XOFF
This is the global setting for all of the designated serial ports for console redirection.
COM A to COM J
Enable or disable the serial redirection function for each of the serial ports on the system. And configure the serial communication parameters to be used between the system
and a remote station.
UseGlobalSetting
Choose to use the pre-configured global settings from the previous menu or configure a
different setting for each serial port.
Page 38
38
www.d.comChapter 7 BIOS Setup
Chapter 7
COM Port 1 and COM Port 6
Enable or disable each serial port.
Disable Disable this serial port.
Enable Enable this serial port.
It also shows the Base I/O address and the assigned interrupt number.
Type
Choose RS232, RS422 or RS485 (Peer-to-Peer) for the serial port type for COM port 1
and 2 only.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable
WDT. Input any value between 1 and 255.
Super I/O
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
PC Health Status
This section displays system status.
Page 39
39
www.d.comChapter 7 BIOS Setup
Chapter 7
Smart Fan Function
This section displays system status.
SYS Smart Fan/SYS Smart Fan 2 Control
Enable or disable the smart fan control.
Boundary 1 to Boundary 4
Set the boundary temperatures that determine the operation of the fan with different
fan speeds accordingly. For example, when the system or the CPU temperature reaches
boundary temperature 1, the system or CPU fan should be turned on and operate at the
designated speed.
The range of the temperature is from 0 to 127oC.
Fan Speed Count 1 to Fan Speed Count 4
Set the fan speed. The range is from 1 (lowest speed)-100% (full speed).
Security
This section configures the Trusted Platform Module (TPM) function.
TPM Availability
Show or hide TPM availability and its configurations.
TPM Operation
Enable or disable the TPM function. It displays the following options:
• No Operation: No changes to the current state.
• Disable: Disable and deactivate TPM.
• Enable: Enable and activate TPM.
Clear TPM
Remove all TPM ownership contents.
Set Supervisor Password
Set the administrative password for entering the BIOS utility or upon the entering of the
power-on self-test (POST) process. The length of the password must be greater than 1
character and less than or equal to 10 characters.
Page 40
40
www.d.comChapter 7 BIOS Setup
Chapter 7
Boot
Setup Prompt Timeout
Select the number of seconds the system will wait before booting the original firmware selection.
NumLock
This allows you to determine the default state of the numeric keypad at boot. By
default, the system boots up with Num Lock on. When set to Off, the function of the
numeric keypad is the arrow keys.
Quiet Boot
Enable or disable the quiet boot function to configure the screen’s display between
POST messages or the OEM logo at bootup. Select Disabled to display the POST messages and select Enabled to display the OEM logo.
Network Stack
Enable or disable network stack. It supports the operation of these functions or software: Windows 8 BitLocker Network Unlock and UEFI IPv4/IPv6 PXE.
PXE Boot Capability
Enable or disable Preboot eXecution Environment (PXE) boot through the Ethernet.
This function can only be enabled if the Network Stack support is enabled.
Note:
The BIOS supports only UEFI boot but not legacy.
EFI
Enter this menu to select the priority of the UEFI boot devices. Use the “+” key to move
an item up or the “-” key to move an item down. The one on the top of the list has the
highest priority.
USB Boot
Enable or disable USB boot from a flash drive.
Page 41
41
www.d.comChapter 7 BIOS Setup
Chapter 7
Exit
Exit Saving Changes
Select this field and press <Enter> to exit BIOS setup and save your changes.
Load Optimal Defaults
Select this field and press <Enter> to load the optimal defaults.
Discard Changes
Select this field and press <Enter>to exit the BIOS setup without saving your changes.
Save Setting to file
Select this option to save BIOS configuration settings to a USB drive. The operation will
fail if there aren’t any USB devices detected on the system. The saved configuration will
have the DSF file extension and can be used for restoration.
Restore Setting from file
Select this option to restore BIOS configuration settings from a USB drive. Note that
this option will not be available if there aren’t any USB devices detected on the system.
Page 42
42
www.d.comChapter 7 BIOS Setup
Chapter 7
Updating the BIOS
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions about how to
update BIOS with the flash utility.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing BIOS updating procedure. For your convenience, we
will also provide you with an auto-execution file in the BIOS file downloaded. This auto-execution file will bring you directly to the flash utility menu soon after system boots up and finishes
running the boot files in your boot disk.
|
|
|
|
Notice: BIOS SPI ROM
1. The Intel® Management Engine has already been integrated into this system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
3. If you do not follow the methods above, the Intel® Management Engine will not be
updated and will cease to be effective.
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
R
Read le successfully. (path= “platform.ini”)
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: KS156-AL
New BIOS Model name: KS156-AL
Current BIOS version: B186.11A
New BIOS version:
Updating Block at FFFFF000h
0% 25% 50% 75% 100%
100%
C:\KS156-AL>_
Information
Please do not remove the AC power
Page 43
43
Chapter 4 Supported Software
Chapter 8
The CD that came with the system board contains drivers, utilities and software applications
required to enhance the performance of the system board.
Insert the CD into a CD-ROM drive. The auto-run screen (the Utility and Manual CD) will appear. If the “Auto-run” does not automatically start, please go directly to the root directory of
the CD and double-click “Setup”.
Auto Run Page (For Windows 10)
Chapter 8 - Supported Software
Page 44
44
Chapter 4 Supported Software
Chapter 8
Intel Chipset Software Installation Utility
The Intel Chipset Device Software is used for updating Windows® INF files so that the Intel
chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Software Installation Utility” in the main menu.
1. Setup is ready to install
the utility. Click “Next” to
continue.
2. Read the license agreement,
then click “Accept” if you
accept the terms and conditions.
4. After the installation is complete, click “Restart Now”.
Restarting the system will allow
the new software installation to
take effect.
3. Go through the readme docu-
ment for more installation tips
then click “Install.”
Page 45
45
Chapter 4 Supported Software
Chapter 8
Intel Graphics Drivers
To install the driver, click “Intel Graphics Drivers” in the main menu.
1. Setup is now ready to install
the graphics driver. Click
“Next” to continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is
enabled. When this is enabled and the system reboots after driver installation, the screen will
turn blank for 1 to 2 minutes (while WinSAT is running) before the Windows 7/ Windows 8
desktop appears. The “blank screen” period is the time Windows is testing the graphics performance.
We recommend that you skip this process by disabling this function and click “Next”.
2. Read the license agreement,
then click “Yes” if you accept
the terms and conditions.
4. Setup is now installing the
driver. Click “Next” to continue.
3. Go through the Readme document for system requirements
and installation tips, then click
“Next”.
5. Click “Yes, I want to restart this
computer now”, then click “Finish” to exit the setup program.
Restarting the system will allow the
new software installation to take
effect.
Page 46
46
Chapter 4 Supported Software
Chapter 8
Intel LAN Drivers
To install the driver, click “LAN Drivers” in the main menu.
1. Setup is ready to install
the driver. Click “Next” to
continue.
2. Click “I accept the terms in
the license agreement” if
you accept the terms and
conditions, then click “Next”.
3. Select the program features
you want to install then
click “Next” to continue.
4. Click “Install” to begin the
installation.
5. After the installation is
complete, click “Finish” to
exit the setup program.
Page 47
47
Chapter 4 Supported Software
Chapter 8
Intel Trusted Execution Engine Driver
To install the driver, click “Intel TXE Drivers” in the main menu.
1. Select “I accept the terms
in the License Agreement”,
then click “Next.”
2. The screen shows the components that will be installed. Click
“Next” to continue.
3. The screen displays the
installation status in
progress.
4. Click “Finish“ when the
installation is complete.
Page 48
48
Chapter 4 Supported Software
Chapter 8
1. Setup is now ready to install the
audio driver. Click “Next” to start
the installation.
3. Click “Yes, I want to restart my
computer now” then click “Finish.”
Restarting the system will allow the
new software installation to take
effect.
Realtek Audio Drivers
To install the driver, click “Realtek Audio Drivers” in the main menu.
2. Follow the on-screen instructions to proceed with the setup
program. Click “Next” each time
you finish a step.
IO Driver
To install the Intel® Serial IO driver, click “IO Driver” in the main menu.
1. Setup is ready to install the
driver. Click “Next” to continue.
2. Read the license agreement carefully.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement, then click
“Next”.
Page 49
49
Chapter 4 Supported Software
Chapter 8
3. Read the file information for installation information, then click “Next”.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
5. Setup is now installing the driver.
6. Click “Finish” to exit setup.
Page 50
50
Chapter 4 Supported Software
Chapter 8
eGalaxTouch Touch Panel Driver
To install this driver, click “eGalaxTouch Touch Screen Driver” in the main menu.
1. Setup is ready to install the driver.
Click “Next” to continue.
2. Read the license agreement care-
fully. Click “I accept the terms of the
license agreement” if you agree with
the terms in the agreement, then click
"Next”.
3. Setup detects that an extra
RS232 interface driver needs to
be installed for the eGalaxTouch
controller. Please check to install
the driver.
4. Select the setup type that best
suits your needs.
Page 51
51
Chapter 4 Supported Software
Chapter 8
5. Select whether to support the
multi-monitor system.
6. Select the installation folder. Follow
the rest of the steps on the screen
to complete the installation procedure.
Loading...