Page 1
KS070-FS Installation Guide
Top Panel I/O Ports
SD COM
Bottom Panel I/O Ports
Line-out/Mic-in
HDMI
8-bit DIO
DFI reserves the right to change the specifications at any time prior
to the product's release. This QIG is based on versions that may not
resemble your actual products. For the latest revision and details of the
installation process, please refer to related technical docs on our website
at http://go.d.com/KS070-FS.
USB 2.0
Mini USB
LAN
(RS232/422/485)
1
COM
DC-in
Power Switch
Page 2
Connecting the Cable to the Terminal Block
The system's power connector is a two-pole terminal block. Please insert the corresponding
end ("+" or "-") of a power adaptor to the respective pole of the terminal block.
1. Insert the cable end of the power adaptor to the terminal block. To rmly x the cable
into the terminal block, use a screwdriver to clamp down the wires to the screw that is in
the terminal block.
Terminal block
Wire
Power adapter cable
2. Plug the terminal block into the DC-in connector and then tighten the screws to secure the
terminal block in place.
DC-in
connector
Screws
White Wire
+ -
Black Wire
2
Page 3
Removing the Chassis Cover
Before working inside the system, make sure the system has been powered off and disconnect
all power cords and cables.
The 8 mounting screws on the sides and bottom of the system are used to secure the cover to
the chassis. Remove these screws and the COM port screws.
Mounting Screw (COM port)
Mounting Screw
Installing the microSD Card
The microSD card slot is located on the Qseven module internally. You may need to remove
the Qseven module rst to access the card slot. Then insert the card straight into the socket.
microSD card
Qseven module
Installing a Mini PCIe and SIM Card
The system board is equipped with 2 Mini PCIe slots.
One Mini PCIe slot (with SIM card slot) provides both
USB and PCIe interfaces whereas the other Mini PCIe
slot provides only mSATA interface.
Before inserting a SIM card into the socket, you have
to remove mounting screws on the speaker.
SIM card into the SIM card socket, and push it to take
the card out of the socket.
Speaker
Mounting screw
Insert the
Note: Be sure to place the card with the IC facing down
and the angled corner aligning with the socket's angled
corner so it will be correctly in contact with the system
board.
3
SIM card socket
Mini PCIe Slot
mSATA Slot
Page 4
Board Layout and Jumper Settings
Mini PCIe (mSATA)
-
Panel Power Select
Touch Panel Power Select
LCD/Inverter Power Select
Dimming Mode Select
+
DC-in
12-36V
1
AMP_L
2
COM RS232/UART5 Select
SIM
(JP2)
(JP3)
1
5
2
6
(JP10)
1
5
2
6
(JP5)
Power
Switch
RTC
Battery
(JP11)/(JP12)
(JP2)
(JP3)
(JP5)
(JP10)
1
40
1
39
4
3
2
1
COM
12
12
13
13
Mini PCIe
LVDS LCD Panel
(JP12)
(JP11)
USB 0-1
LAN
USB 2.0
Mic-in/Line-out
MXM
2
1
Mic-in/
HDMI
Line-out
USB Client
1256125
Mic-in/Line-out
Select (JP8)
Select (JP7)
6
MCS7840CV
SD
Download Mode
Select (JP9)
13
13
14
10129
CAN-bus
(optional)
COM 1 RS232/422/485
Select (JP4)
Digital I/O
ITE
IT8518E
56
10129
12
COM 1
56
COM 2 RS232/422/485
Select (JP6)
12
AMP_R
COM 2
Boot Device Select Switch
eMMC 1 Off, 2 Off, 3 On, 4 On
uSD 1 Off, 2 Off, 3 On, 4 Off
SPI3 on board SPI 1 On, 2 On, 3 Off, 4 On
SPI1 on carrier board 1 On, 2 Off, 3 Off, 4 On
12
1
2
SD LED
Power LED
Dimming Mode Select JP10
PWM Mode (default) 1-2 On
Voltage Mode 2-3 On
COM 1 /COM 2
JP4 (for COM 1), JP6 (for COM 2)
RS232/422/485 Select
RS232 (default) 1-2 On
RS422 3-4 On
RS485 5-6 On
LCD Panel Power Select JP2
+12V 1-2 On
+5V Standby 3-4 On
+3V Standby (default) 5-6 On
Touch Panel Power Select JP3
+5V Standby 1-2 On
+3V Standby (default) 2-3 On
Line-out/Mic-in Select JP7 (for Line-out), JP8 (for Mic-in)
Line-out (JP7) 1-2, 3-4, 5-6 On
Mic-in (JP8) 1-2, 3-4, 5-6 On
LCD/Inverter Power Select JP5
+12V 1-2 On
+5V Standby (default) 3-4 On
+3V Standby 5-6 On
Dimming Mode Select JP5
+12V 1-2 On
+5V Standby (default) 3-4 On
+3V Standby 5-6 On
Download Mode Select JP9
Serial Download Mode 1-2 On
Normal Boot (default) 2-3 On
933-KS0702-000G
A55701930
4
Aug 20, 2019
DVT
Loading...