DFI HD630-H81 User Manual
HD630-H81
ATX Industrial Motherboard
User’s Manual
A27550511
1
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2015. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
2
Table of Contents
Copyright .............................................................................................................2
Trademarks ........................................................................................................2
FCC and DOC Statement on Class B ..................................................... 2
About this Manual ..........................................................................................4
Warranty ..............................................................................................................4
RJ45 LAN Ports ........................................................................................... 23
USB Ports ................................................................................................... 24
Audio ......................................................................................................... 25
I/O Connectors ........................................................................................... 25
SATA (Serial ATA) Connectors ...................................................................... 25
Digital I/O Connector .................................................................................. 26
Cooling Fan Connectors...............................................................................27
Power Connectors ....................................................................................... 27
Chassis Intrusion Connector ........................................................................ 28
Front Panel Connector ................................................................................ 28
Standby Power LED ....................................................................................29
Expansion Slots .......................................................................................... 29
Parallel Port ................................................................................................ 30
S/PDIF Connector ....................................................................................... 31
Battery ....................................................................................................... 31
Static Electricity Precautions ......................................................................4
Safety Measures ..............................................................................................4
About the Package .........................................................................................5
Chapter 1 - Introduction ............................................................................. 6
Specifications ................................................................................................6
Features ..........................................................................................................7
Chapter 2 - Hardware Installation ................................................9
Board Layout ................................................................................................. 9
System Memory ............................................................................................ 9
Installing the DIMM Module ........................................................................ 10
CPU ................................................................................................................ 11
Installing the CPU ....................................................................................... 12
Installing the Fan and Heat Sink.................................................................. 14
Jumper Settings ......................................................................................... 15
Clear CMOS Data ........................................................................................ 15
PS/2 Keyboard/Mouse Power Select ............................................................. 15
USB Power Select ....................................................................................... 16
Power-on Select.......................................................................................... 16
COM1/COM2 RS232/422/485 Select ............................................................. 17
COM1/COM2 RS232/Power Select ................................................................ 17
Mini PCIe Signal Select ............................................................................... 18
Mini PCIe Power Select ............................................................................... 18
Digital I/O Power Select .............................................................................. 19
Digital I/O Output State .............................................................................. 19
SATA DOM Power Select ............................................................................. 20
Rear Panel I/O Ports .................................................................................21
PS/2 Keyboad/Mouse Port ........................................................................... 21
COM (Serial) Ports ...................................................................................... 22
Graphics Interfaces ..................................................................................... 23
Chapter 3 - BIOS Setup ............................................................... 32
Overview ..................................................................................................... 32
AMI BIOS Setup Utility ............................................................................. 33
Main .......................................................................................................... 33
Advanced ................................................................................................... 33
Chipset ...................................................................................................... 43
Boot........................................................................................................... 50
Security ...................................................................................................... 51
Save & Exit ................................................................................................51
Updating the BIOS .................................................................................... 52
Notice: BIOS SPI ROM ............................................................................. 52
Chapter 4 - Supported Software .......................................................... 53
Chapter 5 - Digital I/O Programming Guide .................................... 72
Appendix A - Troubleshooting ................................................................ 74
nLite ............................................................................................................... 74
AHCI .............................................................................................................. 78
Appendix B - Watchdog Sample Code ................................................ 80
Appendix C - System Error Message ................................................... 81
Appendix D - Troubleshooting ................................................................ 82
3
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before
plugging the power cord.
4
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• One HD630 motherboard
• One Serial ATA data cable
• One I/O shield
• One DVD
• One QR (Quick Reference)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
• USB port cable
• Serial ATA data cable
• COM port cable
• I/O shield
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• A CPU
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1 - Introduction
Specifications
Chapter 1
Processor
Chipset
Super I/O
Address
System Memory
Expansion Slots
Graphics
Audio
LAN
• LGA 1150 socket for:
- 4th Generation Intel
®
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
: Intel
• 22nm process technology
CoreTM i7-4790S (8M Cache, up to 4.0 GHz); 65W
®
CoreTM i7-4770S (8M Cache, up to 3.9 GHz); 65W
®
CoreTM i7-4770TE (8M Cache, up to 3.3 GHz); 45W
®
CoreTM i5-4590S (6M Cache, up to 3.7 GHz); 65W
®
CoreTM i5-4590T (6M Cache, up to 3.0 GHz); 35W
®
CoreTM i5-4570S (6M Cache, up to 3.6 GHz); 65W
®
CoreTM i5-4570TE (4M Cache, up to 3.3 GHz); 35W
®
CoreTM i3-4360 (4M Cache, 3.7 GHz); 54W
®
CoreTM i3-4350T (4M Cache, 3.1 GHz); 35W
®
CoreTM i3-4340TE (4M Cache, 2.6 GHz); 35W
®
CoreTM i3-4330 (4M Cache, 3.5 GHz); 54W
®
CoreTM i3-4330TE (4M Cache, 2.4 GHz); 35W
®
Pentium® G3420 (3M Cache, 3.2 GHz); 53W
®
Pentium® G3320TE (3M Cache, 2.3 GHz); 35W
®
Celeron® G1820 (2M Cache, 2.7 GHz); 53W
®
Celeron® G1820TE (2M Cache, 2.2 GHz); 35W
®
CoreTM processors
• Intel® H81 Express Chipset
• NCT6102/4Eh (HD630-H81B/D)
• NCT6106/4Eh (HD630-H81C)
• Two 240-pin DDR3 DIMM sockets
• Supports DDR3 1333/1600MHz
• Supports dual channel memory interface
• Supports up to 16GB system memory
• DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM technologies are
supported for x8 and x16 devices, unbuffered, non-ECC
• 1 PCIe x16 Gen 3 slot (PCIe 3.0)
• 1 PCIe x4 Gen 2 slot (PCIe 2.0)
- x1 signal
• 1 PCIe x1 Gen 2 slot (PCIe 2.0)
• 4 PCI slots (PCI 2.3)
• 1 Mini PCIe slot
- Supports USB and PCIe signals
- Supports mSATA
- Supports half size and/or full size Mini PCIe card
• Intel® HD Graphics
• Display ports: 1 HDMI, 1 DVI-I
• DVI-I: resolution up to 1920x1200 @ 60Hz
• HDMI: resolution up to 4096x2304 @ 24Hz or 2560x1600 @ 60Hz
• VGA: 24-bit, resolution up to 1920x1200 @ 60Hz
• Supports 6 Graphics Execution Units (EUs)
®
Clear Video Technology
• Intel
• DirectX Video Acceleration (DXVA) support for accelerating video processing
• Realtek ALC886 5.1-channel High Defi nition Audio
• Audio outputs: Mic-in/Center+Subwoofer, Line-in/Surround and Line-out
• S/PDIF audio interface
• Intel® I210 PCI Express Gigabit Ethernet controller
®
I217 Gigabit Ethernet Phy (HD630-H81C/D)
• Intel
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Serial ATA
Trusted Platform
Module - TPM*
(optional)
USB Interface
Rear Panel I/O
Ports
I/O Connectors
BIOS
WatchDog Timer
Energy Effi cient
Design
Damage Free
Intelligence
Temperature
• 2 SATA 3.0 ports with data transfer rate up to 6Gb/s
• 2 SATA 2.0 ports with data transfer rate up to 3Gb/s
- SATA port 5 provides adequate space for SATA DOM
• Integrated Advanced Host Controller Interface (AHCI) controller
• Provides a Trusted PC for secure transactions
• Provides software license protection, enforcement and password protection
• XHCI Host Controller supports up to 2 super speed USB 3.0 ports
• 1 mini-DIN-6 port for PS/2 mouse/keyboard
• 2 DB-9 RS232/422/485 serial ports (RS232 and/or Power)
• 1 HDMI port
• 1 DVI-I port
• 2 RJ45 LAN ports (HD630-H81B has 1 RJ45 LAN port only)
• 2 USB 3.0/2.0/1.1 ports
• 4 USB 2.0/1.1 ports
• Line-in/Surround, Line-out, and Mic-in/Center+Subwoofer jacks
• 1 connector for 2 external USB 2.0/1.1 ports (default); or
1 vertical USB 2.0/1.1 port* (optional)
• 4 connectors for 4 external RS232 serial ports
(2.0mm pitch, HD630-H81C only)
• 1 8-bit Digital I/O connector
• 1 front audio connector for line-out and mic-in jacks
• 1 S/PDIF connector
• 1 LPC connector
• 1 parallel port (parallel on HD630-H81D is optional)
• 4 Serial ATA ports
• 1 24-pin ATX power connector
• 1 8-pin 12V power connector
• 1 chassis intrusion connector
• 1 front panel connector
• 3 fan connectors
• AMI BIOS
- 64Mbit SPI BIOS
• Software programmable from 1 to 255 seconds
• Supports ErP Lot6 power saving* (optional)
• Supports ACPI
• System Power Management
• Wake-On-Events include:
- Wake-On-PS/2 KB/Mouse
- Wake-On-USB KB/Mouse
- Wake-On-LAN
- RTC timer to power-on the system
• CPU stopped clock control
• AC power failure recovery
• Monitors CPU/system temperature and overheat alarm
• Monitors VCORE/5V/3.3V/V_DIMM/12V/5VSB voltages and failure alarm
• Monitors CPU/system fan speed and failure alarm
• Read back capability that displays temperature, voltage and fan speed
• Operating: 0oC to 60oC
• Storage: -20
o
C to 85oC
6
Chapter 1 Introduction www.dfi .com
Chapter 1
Humidity
Power
Consumption
OS Support
Dimensions
Certifi cation
Note:
*Optional and is not supported in standard model. Please contact your sales representative for more information.
• 5% to 90%
• 49.85W with i7-4770S at 3.10GHz and 2x 2GB DDR3 DIMM
• Windows XP Professional x86 & SP3 (32-bit)
• Windows 7 Ultimate x86 & SP1 (32-bit)
• Windows 7 Ultimate x64 & SP1 (64-bit)
• Windows 8 Enterprise x86 (32-bit)
• Windows 8 Enterprise x64 (64-bit)
(based on Intel's Windows XP support list)
• ATX form factor
• 305mm (12") x 244mm (9.6")
• CE, FCC Class B, RoHS
Features
• Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
• DDR3
DDR3 delivers increased system bandwidth and improved performance. It offers peak data
transfer rate of up to 16Gb/s bandwidth. The advantages of DDR3 are its higher bandwidth
and its increase in performance at a lower power than DDR2.
• Graphics
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications. Supports HDMI and DVI-I
interfaces for 2 display outputs.
• PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes. The x4 PCI Express lane supports transfer rate of 4 Gigabyte per
second (2 directions). The PCI Express architecture also supports high performance graphics
infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 3Gb/s (SATA 2.0) and 6Gb/s (SATA 3.0), it improves hard drive performance faster than
the standard parallel ATA whose data transfer rate is 100MB/s. The bandwidth of the SATA 3.0
will be limited by carrier board design.
• Gigabit LAN
Two Intel® Gigabit LAN controllers, Intel® I210 PCI Express Gigabit Ethernet controller and In-
®
I217LM Gigabit Ethernet Phy, support up to 1Gbps data transmission.
tel
®
(HD630-H81B supports the Intel
I210 PCI Express Gigabit Ethernet controller only.)
• Audio
The Realtek ALC886 audio codec provides 5.1-channel High Definition audio output.
7
Chapter 1 Introduction www.dfi .com
Chapter 1
• Wake-On-LAN
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Management Event) signal. However, if your system is in the Suspend mode, you can power-on
the system only through an IRQ or DMA interrupt.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the 5V_standby power source of your power supply must support ≥2A.
• RTC Timer
The RTC installed on the system board allows your system to automatically power-on on the
set date and time.
• Wake-On-PS/2
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
• USB
The system board supports the new USB 3.0. It is capable of running at a maximum transmission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously
accessible external Plug and Play peripherals.
• ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
.
function
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to
go through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
Chapter 1 Introduction www.dfi .com
8
Chapter 2 - Hardware Installation
USSBUU.0
.0
Board Layout
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select (JP4)
COM1 RS232/422/485
Select
COM2 RS232/422/485
Select
COM1 RS232/Power
Select
COM2 RS232/Power
Select
(JP2)
(JP11)
(JP3)
(JP14)
PS/2 KB/MS
USB 8-9
USB 2.0
USB 2.0
COM2
COM1
DVI-I
HDMI
LAN 1
USB 0-1
USB 3.0
LAN 2
USB 4-5
USB 2.0
Line-in
Line-out
Mic-in
(JP1)
ASMedia
ASM1442
ASMedia
ASM1442
PCIe x16
5
(JP4)
6
1
(JP14)
1
(JP2)
(JP11)
USB 0-1 Power
1
Select (JP5)
Intel
WGI217LM
1
USB 4-5 Power
Select (JP6)
Intel
WGI210AT
Chapter 2
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
1
5
1
(JP3)
2
2
6
15
56
ISL95820
+12V
12
Power
56
48
12
COM5 COM6
1
91
1
CPU Fan
Buzzer
210
System Fan 2
Socket LGA1150
9
210
1
Chassis
intrusion
Battery
DDR3_1 DDR3_3
1
1
Parallel
Nuvoton
NCT6102D
Power-on
Select (JP10)
Standby
Power LED
LPC
122
11
COM3
COM4
12 24
ATX
Power
113
10 9
10 9
21
System Memory
26
25
12
12
1
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lights red, it indicates that there is power on the
system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
USB 2.0
DDR3-1
DDR3-3
Realtek
ALC886
PCIe x1
S/PDIF
1
10
2
9
1
Front Audio
PCIe x4 (x1 Signal)
PCI 1
PCI 2
DIO 3/5/7/9
Output State (JP12)
DIO 11/13/15/17
Output State (JP7)
DIO Power Select
(JP13)
• HD630-H81B has LAN1 only.
• HD630-H81C: 6 COM (COM1 to COM6).
HD630-H81B/D: 2 COM (COM1 and COM2).
(JP13)
111
PCI 3
PCI 4
(JP12)
(JP7)
19
1
DIO
2
ITE
IT8892E
Select (JP15/JP18)
System Fan 1
Intel
H81
Clear CMOS Data (JP9)
Note:
SATA5 supports SATA DOM.
Mini PCIe Signal
Mini PCIe Power
Select (JP16)
1
USB 2.0
10
USB 2-3
12 10
1
3
1
12 10
129
3
1
SATA 4
1
SPI Flash
USB 2-3 Power
Select (JP8)
SATA DOM Power
SATA 2.0
1
1
Mini PCIe
BIOS
SATA 3.0
SATA 0
1
SATA 1
1
1
Select (JP17)
SATA 5
1
Standby
Power LED
Rear I/O
Onboard I/O
12
Front
Panel
1112
Storage
Expansion
Features
• Two 240-pin DDR3 DIMM sockets
• Supports DDR3 1333/1600MHz
• Supports dual channel memory interface
• Supports up to 16GB system memory
9
Chapter 2 Hardware Installation
www.dfi .com
Chapter 2
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits (8B) from the memory channels.
Dual Channel (DC)
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
DIMMs are on the same channel.
Single Channel
Dual Channel
DIMMs in a channel can be identical or
completely different. However, we highly
recommend using identical DIMMs.
Not all slots need to be populated.
DIMMs of the same memory configuration
are on different channels.
Installing the DIMM Module
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board.
4. Push the “ejector tabs” which are at the ends of the socket to the side.
Ejector tab
5. Note how the module is keyed to the socket.
Notch
Key
Ejector tab
Chapter 2 Hardware Installation
10
www.dfi .com
Chapter 2
6. Grasping the module by its edges, position the module above the socket with the “notch”
in the module aligned with the “key” on the socket. The keying mechanism ensures the
module can be plugged into the socket in only one way.
7. Seat the module vertically, pressing it down firmly until it is completely seated in the
8. The ejector tabs at the ends of the socket will automatically snap into the locked position
socket.
to hold the module in place.
CPU
The system board is equipped with a surface mount LGA 1150 socket. This socket is exclusively designed for installing a LGA 1150 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1150 socket comes with a protective
cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If
the cap is missing or the cap and/or contact pins are damaged, contact your dealer
immediately.
2. Make sure to keep the protective cap. RMA requests will be accepted and processed only if the LGA 1150 socket comes with the protective cap.
Protective
cap
Chapter 2 Hardware Installation
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
11
www.dfi .com
Chapter 2
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
2. Disconnect all power cords and cables.
3. Locate the LGA 1150 CPU
socket on the system
board.
Important:
The CPU socket must not come in contact with anything other than the CPU. Avoid
unnecessary exposure. Remove the protective cap only when you are about to install
the CPU.
4. Unlock the socket by pushing the load lever down,
moving it sideways until it
is released from the retention tab; then lift the load
lever up.
USB 2.0
Load lever
5. Lifting the load lever will at
the same time lift the load
plate.
Lift the load lever up to
the angle shown on the
photo.
6. Remove the protective cap
from the CPU socket. The
cap is used to protect the
CPU socket against dust
and harmful particles.
Remove the protective cap
only when you are about
to install the CPU.
Load
plate
Load lever
Protective cap
Chapter 2 Hardware Installation
Retention tab
12
www.dfi .com
Chapter 2
7. Insert the CPU into the
socket. The gold triangular
mark on the CPU must
align with the corner of
the CPU socket shown on
the photo.
The CPU’s notch will at
the same time fit into the
socket’s alignment key.
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
Alignment key
Alignment key
Gold triangular mark
8. Close the load plate then
push the load lever down.
While closing the load
plate, make sure the front
edge of the load plate
slides under the retention
knob.
9. Hook the load lever under
the retention tab.
Retention knob
Load lever
Retention tab
Chapter 2 Hardware Installation
13
www.dfi .com
Chapter 2
Installing the Fan and Heat Sink
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system
board.
Note:
A boxed Intel
CPU was purchased separately, make sure to only use Intel
sink.
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of the
CPU. The thermal paste is usually supplied when you purchase the fan / heat sink assembly. Do not spread the paste all over the surface. When you later place the heat sink on
top of the CPU, the compound will disperse evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel the
strip that covers the paste before you place the fan / heat sink on top of the CPU.
2. Place the heat sink on top
of the CPU. The 4 pushpins around the heat sink,
which are used to secure
the heat sink onto the system board, must match the
4 mounting holes around
the socket.
®
processor already includes the CPU fan and heat sink assembly. If your
USB 2.0
®
-certified fan and heat
Mounting hole
4. Rotate each push-pin according to the direction of
the arrow shown on top of
the pin.
Push down two pushpins
that are diagonally across
the heat sink. Perform the
same procedure for the
other two push-pins.
5. Connect the CPU fan’s
cable to the CPU fan
connector on the system
board.
Heat sink
“Locked” position of
push-pin
USB 2.0
“Unlocked” position
of push-pin
CPU Fan connector
3. Orient the heat sink such
that the CPU fan’s cable is
nearest the CPU fan connector.
Chapter 2 Hardware Installation
USB 2.0
CPU Fan connector
14
www.dfi .com
Chapter 2
Jumper Settings
Clear CMOS Data
USB 2.0
312
1-2 On: Normal
(default)
JP9
2-3 On:
Clear CMOS Data
If you encounter the followings,
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
you can reconfigure the system with the default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
PS/2 Keyboard/Mouse Power Select
USB 2.0
JP1
312
JP1 is used to select the power of the PS/2 keyboard/mouse port. Selecting +5V_standby will
allow you to use the PS/2 keyboard or the PS/2 mouse to wake up the system.
Important:
The +5V_standby power source of your power supply must support ≥720mA.
312
1-2 On: +5V
(default)
+5V_standby
312
2-3 On:
1. Power-off the system and unplug the power cord.
2. Set JP9 pins 2 and 3 to On. Wait for a few seconds and set JP9 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
Chapter 2 Hardware Installation
15
www.dfi .com
Chapter 2
USB Power Select
USB 8-9
(JP4)
USB 2.0
312
1-2 On: +5V
(default)
312
2-3 On:
+5V_standby
USB 0-1
(JP5)
USB 4-5
(JP6)
USB 2-3
(JP8)
3
2
1
1-2 On: +5V
(default)
3
2
1
2-3 On:
+5V_standby
Power-on Select
USB 2.0
3
2
1
1-2 On:
Power-on via power button
JP10
JP10 is used to select the method of powering on the system. If you want the system to
power-on whenever AC power comes in, set JP10 pins 2 and 3 to On. If you want to use the
power button, set pins 1 and 2 to On.
(default)
3
2
1
2-3 On:
Power-on via AC power
JP4, JP5, JP6 and JP8 are used to select the power of the USB devices. Selecting +5V_standby
will allow you to use a USB device to wake up the system.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
Chapter 2 Hardware Installation
When using JP10 “Power-On” feature to power the system back on after a power failure
occurs, the system may not power on if the power lost is resumed within 5 seconds (power
flicker).
16
www.dfi .com
Chapter 2
COM1/COM2 RS232/422/485 Select
COM 2
COM 1
COM 1/COM 2:
RS232/422/485
JP2 (for COM1) and JP11 (for COM2) are used to configure the COM ports to RS232, RS422
(Full Duplex) or RS485. The pin functions of the COM ports will vary according to the jumper’s
setting.
USB 2.0
JP2
JP11
JP2/JP11
COM1/COM2 RS232/Power Select
13 5
4 6
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
COM 2
COM 1
2
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
JP14 JP3
USB 2.0
13 5
2
4 6
5
6
4
1-2 On: RS232
2
(default)
3
1
COM 1/ COM 2
TD
RD
DTR-
DCD2345
1
GND
12345
6789
RI-
RTS-
CTS-
DSR-
RS232
Chapter 2 Hardware Installation
5
6
4
3
TXD+
RXD-
1
TXD-
N.C.
2
3-4 On: RS422
Full Duplex
RXD+
6789
N.C.
N.C.
N.C.
N.C.
RS422
Full Duplex
5
6
4
2
3
1
5-6 On: RS485
DATA-
N.C.
N.C.
N.C.
DATA+
12345
6789
N.C.
N.C.
N.C.
N.C.
RS485
JP3 (for COM 1) and JP14 (for COM 2) are used to configure Serial COM ports to pure RS232
or RS232 with power. The pin functions of COM 1 and COM 2 will vary according to JP3’s and
JP14’s setting respectively.
17
www.dfi .com
Chapter 2
Mini PCIe Signal Select Mini PCIe Power Select
USB 2.0
USB 2.0
12 10
1
3
1-4-7-10, 2-5-8-11 On:
PCIe (default)
12 10
JP16
JP18
JP15
1
3
2-5-8-11, 3-6-9-12 On:
mSATA
JP15 and JP18 are used to select the Mini PCIe signal. JP16 is used to select the power supplied with the Mini PCIe.
132 132
1-2 On: +3.3V
(default)
2-3 On:
+3V_standby
Chapter 2 Hardware Installation
18
www.dfi .com
Chapter 2
Digital I/O Power Select Digital I/O Output State
USB 2.0
3
2
1
1-2 On: +5V_standby
(default)
3
2
JP13
1
2-3 On: +5V
JP13 is used to select the power of DIO (Digital I/O) signal.
DIO 11/13/15/17
(JP7)
1
1-2 On: +5V or
+5V_standby
(default)
USB 2.0
DIO 3/5/7/9
(JP12)
3
2
3
2
1
2-3 On: GND
Chapter 2 Hardware Installation
Based on the power level of DIO (Digital I/O) selected on JP13, JP12 (DIO pin 3/5/7/9) and
JP7 (DIO pin 11/13/15/17) are used to select the state of DIO output: pull high or pull low.
When selecting pull high, the power selection will be the same as JP13’s setting.
19
www.dfi .com
SATA DOM Power Select
USB 2.0
Chapter 2
JP17 is used to select the power of SATA DOM.
Note:
SATA port 5 provides adequate space for SATA DOM.
SATA 5
JP17
312
1-2 On: GND
(default)
312
2-3 On: +5V
Chapter 2 Hardware Installation
20
www.dfi .com
Chapter 2
Rear Panel I/O Ports
COM 2
PS/2 KB/MS
USB 2.0
COM 1
The rear panel I/O ports consist of the following:
• 1 PS/2 Keyboard/Mouse port
• 2 Serial COM ports
• 1 HDMI port
• 1 DVI-I port
• 2 RJ45 LAN ports
(HD630-H81B has LAN 1 only.)
• 2 USB 3.0 ports
• 4 USB 2.0 ports
• Line-in/Surround jack
• Line-out jack
• Mic-in/Center+Subwoofer jack
DVI-I
HDMI
LAN 1
USB 3.0
LAN 2
USB 2.0
Line-in/Surround
Line-out
Mic-in/
Center+Subwoofer
PS/2 Keyboard/Mouse Port
PS/2 Keyboard/Mouse
USB 2.0
This rear I/O port is used to connect a PS/2 keyboard/mouse. The PS/2 mouse port uses
IRQ12.
Chapter 2 Hardware Installation
Wake-On-PS/2 Keyboard/Mouse
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power-on the system. To use this function:
• Jumper Setting
JP1 must be set to “2-3 On: +5V_standby”. Refer to “PS/2 KB/MS Power Select” in this chapter
for more information
• BIOS Setting
Configure the wake-up function of PS/2 keyboard/mouse in the Advanced menu (“ACPI Power
Management Configuration” submenu) of the BIOS. Refer to the chapter 3 for more information.
Important:
The +5V_standby power source of your power supply must support ≥720mA.
21
.
www.dfi .com
Chapter 2
COM (Serial) Ports
COM 2
COM 1
COM 1/COM 2:
RS232/422/485
USB 2.0
TD
RI-
RTS-
GND
DSR-
CTS-
DTR-
COM 5 COM 6
DCD-
19
COM 5/COM 6:
2
RS232
RD
COM 3
COM 4
CTS-
DSR-
DTR-
RD
21
COM 3/COM 4:
RS232
BIOS Setting
Configure the serial COM ports in the Advanced menu (“Super IO Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
Note:
HD630-H81C: 6 COM (COM 1 to COM 6).
HD630-H81B/D: 2 COM (COM 1 and COM 2).
9
RIRTS-
GND
TD
DCD-
COM 3 to COM 6 are fixed at RS232.
The pin functions of COM 1 and COM 2 port will vary according to JP2’s (for COM 1) and
JP11’s (for COM 2) setting. JP3 (for COM 1) and JP14 (COM 2) are used to configure Serial
COM ports to pure RS232 or RS232 with power. Refer to “COM1/COM2 RS232/422/485 Select”
and “COM1/COM2 RS232/Power Select“ in this chapter for more information.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
Connecting External Serial Ports
Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket to
an available slot at the rear of the system chassis then insert the serial port cable to the COM
connector. Make sure the colored stripe on the ribbon cable is aligned with pin 1 of the COM
connector.
Chapter 2 Hardware Installation
22
www.dfi .com
Chapter 2
Graphics Interfaces
The display ports consist of the following:
• 1 DVI-I port
• 1 HDMI port
USB 2.0
DVI-I
HDMI
DVI-I Port
The DVI-I port is used to connect an LCD monitor. This port supports DVI-D signal only.
Connect the display device’s cable connector to the DVI-I port. After plugging the cable connector into the port, gently tighten the cable screws to hold the connector in place.
HDMI Port
The HDMI port which carries both digital audio and video signals is used to connect a LCD
monitor or digital TV that has the HDMI port.
BIOS Setting
RJ45 LAN Ports
USB 2.0
LAN 1
Features
• Intel® I210 PCI Express Gigabit Ethernet controller
• Intel
The LAN port allows the system board to connect to a local area network by means of a
network hub.
BIOS Setting
Configure the onboard LAN ports in the Chipset menu (“PCH-IO Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
Driver Installation
Install the LAN drivers. Refer to the chapter 4 for more information.
LAN 2
LAN 1
LAN 2
®
I217LM Gigabit Ethernet Phy
Configure the display devices in the Chipset menu (“System Agent Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
Chapter 2 Hardware Installation
Note:
HD630-H81B supports the Intel
®
I210 PCI Express Gigabit Ethernet controller (LAN 1)
only.
23
www.dfi .com
Chapter 2
USB Ports
USB 2.0
USB 3.0
USB 2.0
USB 9
USB 8
USB 1
USB 0
USB 5
USB 4
USB 2.0
USB 2.0
10
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function:
• Jumper Setting
JP4, JP5, JP6 and JP8 must be set to “2-3 On: +5V_standby”. Refer to “USB Power Select” in
this chapter for more information.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
GND
Key
9
-Data
+Data
VCC
1
2
USB 2-3
VCC
GND
N. C.
-Data
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with two onboard USB 3.0/2.0/1.1 ports (USB 0-1) and four
onboard USB 2.0/1.1 ports (USB 4-5/8-9). The 10-pin connector allows you to connect 2 additional USB 2.0/1.1 ports (USB 2-3). The additional USB ports may be mounted on a card-edge
bracket. Install the card-edge bracket to an available slot at the rear of the system chassis and
then insert the USB port cables to a connector.
BIOS Setting
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to the chapter 3 for more information.
Driver Installation
You may need to install the proper drivers in your system operation to use the USB device.
Refer to your operating system’s manual or documentation for more information.
+Data
Chapter 2 Hardware Installation
24
www.dfi .com
Chapter 2
Audio
Rear Audio
Line-in/Surround
Line-out
Mic-in/
Center+Subwoofer
Presence Signal
Line2-JD
Mic2-JD
GND
Key
2
1
Mic2-L
Rear Audio
The system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
• Line-in/Surround Jack (Light Blue)
This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player,
AM/FM radio tuner, synthesizer, etc.
• Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
• Mic-in/Center+Subwoofer Jack (Pink)
This jack is used to connect an external microphone.
Front Audio
The front audio connector allows you to connect to the second line-out and mic-in jacks that
are at the front panel of your system.
10
9
Mic2-R
Line2-L
Line2-R
Front_IO_Sense
Front
Audio
USB 2.0
I/O Connectors
SATA (Serial ATA) Connectors
USB 2.0
RXN
TXN
GND
1
TXP
GND
SATA 5
7
RXP
GND
SATA 3.0 6Gb/s
SATA 0
SATA 1
SATA 4
SATA 2.0 3Gb/s
(SATA port 5 provides adequate
Features
• 4 Serial ATA ports
- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s (SATA 0 and SATA 1)
- 2 SATA 2.0 ports with data transfer rate up to 3Gb/s (SATA 4 and SATA 5)
• Integrated Advanced Host Controller Interface (AHCI) controller
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
The system board package comes with a power cable that must be connected from the system
board’s peripheral power connector to the SATA drive’s power connector in order to provide
power to the drive.
space for SATA DOM.)
Driver Installation
Install the audio driver. Refer to the chapter 4 for more information.
Chapter 2 Hardware Installation
25
www.dfi .com
Loading...