DFI CR901-B User Manual

Page 1
CR901-B
COM Express Basic Module
User’s Manual
A20960511
1
www.d .comChapter 1 Introduction
Page 2
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be re­produced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifi­cally disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this docu­ment. Further, the manufacturer reserves the right to revise this publication and make changes to its contents at any time, without obligation to notify any person or entity of such revisions or changes.
Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.
© 2015. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and are the properties of the respective owners.
COM Express Specification Reference
PICMG® COM Express ModuleTM Base Specification. http://www.picmg.org/
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason­able protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour­aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli­ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
2
www.dfi .comChapter 1 Introduction
Page 3
Table of Contents
Copyright .............................................................................................................2
Trademarks ........................................................................................................2
FCC and DOC Statement on Class B .....................................................2
About this Manual ..........................................................................................4
Chapter 4 - BIOS Setup ............................................................... 32
Overview ..................................................................................................... 32
AMI BIOS Setup Utility .............................................................................33
Main ..........................................................................................................33
Advanced ...................................................................................................33
Chipset ......................................................................................................39
Boot...........................................................................................................43
Security ...................................................................................................... 44
Save & Exit ................................................................................................ 44
Updating the BIOS ....................................................................................45
Notice: BIOS SPI ROM .............................................................................46
Warranty ............................................................................................................4
Static Electricity Precautions ......................................................................4
Safety Measures ..............................................................................................4
About the Package .........................................................................................5
Chapter 1 - Introduction .............................................................................6
Specifications ................................................................................................6
Features ........................................................................................................7
Chapter 2 - Concept .......................................................................8
COM Express Module Standards ..............................................................8
Specification Comparison Table ...............................................................9
Chapter 3 - Hardware Installation .............................................. 10
Board Layout ...............................................................................................10
Block Diagram .............................................................................................10
Mechanical Diagram ..................................................................................11
System Memory ..........................................................................................12
Installing the DIMM Module ........................................................................13
CPU ...........................................................................................................14
Connectors ...................................................................................................15
CPU Fan Connector .....................................................................................15
COM Express Connectors ............................................................................16
COM Express connector Signal Discription .................................................... 18
Standby Power LED ................................................................................... 28
Cooling Option ............................................................................................28
Installing CR901-B onto a Carrier Board ............................................29
Chapter 5 - Supported Software .......................................................... 47
Appendix A - nLite and AHCI Installation Guide ...........................60
nLite ...............................................................................................................60
AHCI ..............................................................................................................64
Appendix B - Watchdog Sample Code ................................................66
Appendix C - System Error Message ...................................................67
Appendix D - Troubleshooting ................................................................68
3
www.dfi .comChapter 1 Introduction
Page 4
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product, in­ability to use the product, unauthorized replacement or alteration of components and prod­uct specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal­lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum­stances, attempt to perform service, adjustments or repairs on the product, whether in or out of warranty. It must be returned to the purchase point, factory or authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the product that has been modified or altered.
It is quite easy to inadvertently damage your PC, system board, components or devices even before installing them in your system unit. Static electrical discharge can damage computer components without causing any signs of physical damage. You must take extra care in han­dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con­nectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com­ponents. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wear­ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic­ing. After installation or servicing, cover the system chassis before plugging the power cord.
4
www.dfi .comChapter 1 Introduction
Page 5
About the Package
The package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance.
• One CR901-B board
• One Heat sink kit
• One DVD
• One QR (Quick Reference)
Optional Items
• COM331-B carrier board kit
• COM101-BAT carrier board kit
• Heat spreader: TBD
• Heat sink with fan
• Heat spreader with heat sink and fan: TBD The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components. If you are installing the system board in a new system, you will need at least the following
internal components.
• A CPU
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc. You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
www.dfi .comChapter 1 Introduction
Page 6
Chapter 1 - Introduction
Specifications
Processor
Chipset System Memory
Graphics
Audio LAN
Serial ATA
USB Interface SSD (optional)
• Socket G2 988B for:
- 3rd Generation Intel : Intel : Intel : Intel
- 2nd Generation Intel : Intel : Intel : Intel : Intel
®
Core™ i7-3610QE (6M Cache, up to 3.3 GHz); 45W
®
Core™ i5-3610ME (3M Cache, up to 3.3 GHz); 35W
®
Core™ i3-3120ME (3M Cache, 2.4 GHz); 35W
®
Core™ i7-2710QE (6M Cache, up to 3.0 GHz); 45W
®
Core™ i5-2510E (3M Cache, up to 3.1 GHz); 35W
®
Core™ i3-2330E (3M Cache, 2.2 GHz); 35W
®
Celeron® B810 (2M Cache, 1.6 GHz); 35W
®
CoreTM processors (22nm process technology)
®
CoreTM processors (32nm process technology)
• Intel® QM77 Express chipset
• Two 204-pin SODIMM sockets
• Supports DDR3 SODIMM
3rd Generation Processors 2nd Generation Processors
DDR3 1066/1333/1600MHz DDR3 1066/1333MHz (i5/i3/Celeron)
• Supports DDR3L SODIMM
- 1066/1333MHz when operating at 1.35V
- 1066/1333/1600MHz when operating at 1.5V
• Supports dual channel memory interface
• Supports up to 16GB system memory
• DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM technologies are supported for x8 and x16 devices, unbuffered, non-ECC
• Intel® HD Graphics 4000
• Supports VGA, LVDS and DDI interfaces
• VGA: resolution up to 2048x1536 @ 75Hz
• LVDS: Single Channel - 18/24-bit; Dual Channel - 36/48-bit, resolution up to 1920x1200 @ 60Hz
• Digital Display Interfaces: HDMI, DVI, DP and SDVO (for Port B)
• HDMI, DVI, DP: resolution up to 1920x1200 @ 60Hz
®
Clear Video Technology
• Intel
• DirectX Video Acceleration (DXVA) for accelerating video processing
- Full AVC/VC1/MPEG2 HW Decode
• Supports DirectX 11/10.1/10/9 and OpenGL 3.0
• Supports High Defi nition Audio interface
• Intel® 82579LM Gigabit Ethernet PHY
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• Supports 4 Serial ATA interfaces
• 2 SATA 3.0 with data transfer rate up to 6Gb/s
2 SATA 2.0 with data transfer rate up to 3Gb/s
• Integrated Advanced Host Controller Interface (AHCI) controller
• Supports RAID 0/1/5/10
• XHCI Host Controller supports up to 4 super speed USB 3.0 ports
• 4GB/8GB/16GB/32GB
• Write: 30MB/sec (max), Read: 70MB/sec (max)
• SATA to SSD onboard
DDR3 1600MHz (i7)
Chapter 1
Watchdog Timer
Trusted Platform Module (TPM) ­optional
Expansion Interfaces
Damage Free Intelligence
BIOS Power
Consumption OS Support
Temperature
Humidity Power PCB
Certifi cation
• Watchdog timeout programmable via software from 1 to 255 seconds
• Provides a Trusted PC for secure transactions
• Provides software license protection, enforcement and password protection
• Supports 12 USB interfaces
- 4 USB 3.0
- 8 USB 2.0
• Supports 1 PCIe x16 interface
- Supports Gen 3.0 (3rd generation processors)
- Supports Gen 2.0 (2nd generation processors)
- Confi gurations (supported only via a riser card): : One x8 (GFX) and two x4 (I/O) : Two x8 (GFX, I/O) : One x16 (GFX, I/O)
• Supports 1 PCIe x4 and 3 PCIe x1 (default); or 7 PCIe x1 interfaces
• Supports LPC interface
• Supports SMBus interface
• Supports I
2
C interface
• Supports 2 serial interfaces (TX/RX)
• Supports 4-bit input and 4-bit output GPIO
• Detects CPU temperature
• Detects CPU fan speed
• Detects Vcore/VGFX/DDR voltages
• Watchdog timer function
• 64Mbit SPI BIOS
• 63.06 W with i7-3610QE at 2.30GHz and 2x 2GB DDR3 SODIMM
• Windows XP Professional x86 & SP3 (32-bit)
• Windows XP Professional x64 & SP2 (64-bit)
• Windows 7 Ultimate x86 & SP1 (32-bit)
• Windows 7 Ultimate x64 & SP1 (64-bit)
• Windows 8 Enterprise x86 (32-bit)
• Windows 8 Enterprise x64 (64-bit)
• Operating: 0oC to 60oC
• Storage: -20
o
C to 85oC
• 10% to 90%
• Input: 5VSB (option), 12V, VCC_RTC
• Dimensions
- COM Express Basic
- 95mm (3.74") x 125mm (4.9")
• Compliance
- PICMG COM Express R2.1 basic form factor, Type 6
• CE
• FCC Class B
• RoHS
• UL
6
www.dfi .comChapter 1 Introduction
Page 7
Chapter 1
Features
Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set time interval. If the system hangs or fails to function, it will reset at the set time interval so that your system will continue to operate.
DDR3
DDR3 delivers increased system bandwidth and improved performance. The advantages of DDR3 are its higher bandwidth and its increase in performance at a lower power than DDR2.
Graphics
Note:
If you are connecting 3 display devices, make sure 2 of the devices are connected via the DisplayPort interface.
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance and features to meet business needs. It provides excellent video and 3D graphics with out­standing graphics responsiveness. These enhancements deliver the performance and compat­ibility needed for today’s and tomorrow’s business applications. Supports LVDS, VGA and DDI for up to 3 independent displays.
Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of up to 3Gb/s (SATA 2.0) and 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel ATA whose data transfer rate is 100MB/s. The bandwidth of the SATA 3.0 will be limited by carrier board design.
Gigabit LAN
The Intel 82579LM Gigabit LAN controller supports up to 1Gbps data transmission.
USB
The system board supports the new USB 3.0. It is capable of running at a maximum transmis­sion speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s) and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces power consumption, and is backward compatible with USB 2.0. It is a marked improvement in device transfer speeds between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
7
www.dfi .comChapter 1 Introduction
Page 8
Chapter 2 - Concept COM Express Module Standards
The figure below shows the dimensions of the different types of COM Express modules. CR901-B is a COM Express Basic module. The dimension is 95mm x 125mm.
Common for all Form Factors Extended only Basic only Compact only Compact and Basic only Mini only
Chapter 2
106.00
Extended
91.00
18.00
6.00
0.00
4.00
0.00
16.50
Mini
8
74.20
80.00
91.00
BasicCompact
70.00
51.00
4.00
121.00
151.00
www.dfi .comChapter 2 Concept
Page 9
Chapter 2
/
/
/
Specification Comparison Table
The table below shows the COM Express standard specifications and the corresponding specifications supported on the CR901-B module.
COM Express Module Base
Connector Feature
A-B A-B PCI Express Lanes 0 - 5 1 / 6 6 A-B LVDS Channel A 0 / 1 1 A-B LVDS Channel B 0 / 1 1 A-B eDP on LVDS CH A pins 0 / 1 0 A-B VGA Port 0 / 1 1 A-B TV-Out NA NA A-B DDI 0 NA NA
5
A-B A-B CAN interface on SER1 0 / 1 0
A-B SATA / SAS Ports 1 / 4 4 A-B AC’97 / HDA Digital Interface 0 / 1 1 A-B USB 2.0 Ports 4 / 8 8 A-B USB Client 0 / 1 0 A-B USB 3.0 Ports NA NA A-B LAN Port 0 1 / 1 1 A-B Express Card Support 1 / 2 2 A-B LPC Bus 1 / 1 1 A-B SPI 1 / 2 1 A-B
6
A-B A-B SMBus 1 / 1 1
A-B I2C 1 / 1 1 A-B Watchdog Timer 0 / 1 1 A-B Speaker Out 1 / 1 1 A-B External BIOS ROM Support 0 / 2 1 A-B Reset Functions 1 / 1 1
Serial Ports 1 - 2 0 / 2 2
SDIO (muxed on GPIO) 0 / 1 0 General Purpose I/O 8 / 8 8
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Max
Min
System I/O
System Management
DFI CR901-B Type 6
• 5 Indicates 12V-tolerant features on former VCC_12V signals.
• 6 Cells in the connected columns spanning rows provide a rough approximation of features sharing connector pins.
COM Express Module Base
Connector Feature
A-B A-B Thermal Protection 0 / 1 1 A-B Battery Low Alarm 0 / 1 1 A-B Suspend/Wake Signals 0 / 3 2 A-B Power Button Support 1 / 1 1 A-B Power Good 1 / 1 1 A-B VCC_5V_SBY Contacts 4 / 4 4
5
A-B
5
A-B
5
A-B A-B Trusted Platform Modules 0 / 1 1
A-B A-B VCC_12V Contacts 12 / 12 12
Sleep Input 0 / 1 1 Lid Input 0 / 1 1 Fan Control Signals 0 / 2 2
Specification Type 6
(No IDE or PCI, add DDI+ USB3) Min
Max
Power Management
Power
DFI CR901-B Type 6
Module Pin-out - Required and Optional Features C-D Connector. PICMG® COM.0Revision 2.1
COM Express Module Base
Connector Feature
C-D
6
C-D
6
C-D C-D C-D VCC_12V Contacts 12 / 12 12
PCI Express Lanes 16 - 31 0 / 16 16 PCI Express Graphics (PEG) 0 / 1 1 Muxed SDVO Channels 1 - 2 NA NA PCI Express Lanes 6 - 15 0 / 2 1 PCI Bus - 32 Bit NA NA PATA Port NA NA LAN Ports 1 - 2 NA NA DDIs 1 - 3 0 / 3 3 USB 3.0 Ports 0 / 4 4
Specification Type 6
(No IDE or PCI, add DDI+ USB3) Min
Max
System I/O
Power
DFI CR901-B Type 6
9
www.dfi .comChapter 2 Concept
Page 10
Chapter 3 - Hardware Installation
PEG 16x LANES
S
us
S
us
HD A
udio
LPC Bus
USB
2.0
8x
SATA 2.0 2x, SATA 3.0 2x
LVDS (Dual Channel)
CRT
PCIe x1
,
Lane 6
2
d
SPI Bus
Serial Port1, 2 TX/RX
Sys FAN PWM/TACH_IN
LAN Ports
SATA Port4
DDI Port B/SDVO Port B
DDI Port C
DDI Port D
USB 3.0 4x
PCIe x1 Lane 7
C Bus
Board Layout
Chapter 3
Block Diagram
CPU fan
1
Standby Power LED
SSD
(optional)
Intel 82579LM
Intel
QM77
SPI Flash BIOS
Top View
Socket G2
rPGA-988B
DDR3_1 SODIMM
DDR3_2 SODIMM
A / B
Channel A
1066/1333/
DDR3
SODIMM
DDR3
SODIMM
SM Bus
M B
8-bit DIO
2
C Bus
I
WDT
SATA 2.0 2x, SATA 3.0 2x
Sys FAN PWM/TACH_IN
LAN Ports
1600MHz
Channel B
1066/1333/
1600MHz
CMOS Backup
EEPROM
HD Audio
LPC Bus
LPC TPM 1.2
SLB9635(option)
GPIO,WDT,I2C
(Embedded
Controller)
USB 2.0 8x
LVDS (Dual Channel)
CRT
PCIe x1, Lane 6
nd
SPI Bus
2
Serial Port1, 2 TX/RX
PCIe x1, Lane 8
SM Bus
M B
Processor
CORE
CORE CORE CORE
rd
3
Generation;
®
Intel
Corei7/i5/i3
nd
2
Generation;
®
Intel
Corei7/i5/i3; Intel® Celeron
Graphics
CORE
(Direct Media
Controller
DMI x4
Interface)
Mobile Intel® QM77
Express Chipset
Memory
(Flexible Display
®
Intel
FDI
Interface)
(Vcore,Vgfx)
PEG 16x LANES
DDI Port B/SDVO Port B
DDI Port C
DDI Port D
USB 3.0 4x
PCIe x1 Lane 7
SATA Port4
IMVP7
SSD Chip
option)
(
C / D
iTE
IT8518E
D110
C110 B110
A110
COM Express connector
COM Express connector
Bottom View
Intel® GLAN
D1
C1 B1
A1
10
PHY 82579LM
www.dfi .comChapter 3 Hardware Installation
Page 11
Mechanical Diagram
CR901-B Module with Heat Sink
4.00
95.00
87.00
Chapter 3
87.00
4.08
0.00
CR901-B Module (Top View)
87.00
117.00
121.00
Ø2.70(*7 pcs)
91.00
87.00
95.00
36.70
2.00
1.60
4.00
4.00 87.00
34.70
24.70
5.0 or 8.0 mm
Side View of the Module with Heat Sink and Carrier Board
Standoff
76.00
Cooler
24.70
34.70
Module PCB
3.50 Module PCB The height of
the highest parts
CarrierBoard
43.67
0.00
4.00
4.08
0.00
70.20
125.00
76.00
12.50
117.00
0.00
95.00
14.00
2.00
0.00
(Bottom View)
11
www.dfi .comChapter 3 Hardware Installation
Page 12
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in boards, and other components. Perform installation procedures at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wear­ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection.
System Memory
The system board is equipped with two 204-pin SODIMM sockets that support DDR3 memory modules.
Important:
When the Standby Power LED lit red, it indicates that there is power on the board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the board and components.
Chapter 3
Standby
Power LED
DDR3_2
DDR3_1
12
www.dfi .comChapter 3 Hardware Installation
Page 13
Chapter 3
Installing the DIMM Module
Note:
The system board used in the following illustrations may not resemble the actual one. These illustrations are for reference only.
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
2. Disconnect all power cords and cables.
3. Locate the SODIMM socket on the system board.
4. Note the key on the socket. The key ensures the module can be plugged into the socket in only one direction.
5. Grasping the module by its edges, align the module into the socket at an approximately 30 degrees angle. Apply firm even pressure to each end of the module until it slips down into the socket. The contact fingers on the edge of the module will almost completely disappear inside the socket.
6. Push down the module until the clips at each end of the socket lock into position. You will
hear a distinctive “click”, indicating the module is correctly locked into position.
Clip
Clip
13
www.d.comChapter 3 Hardware Installation
Page 14
Chapter 3
CPU
Overview
The system board is equipped with a surface mount rPGA 988B CPU socket.
Note:
The system board used in the following illustrations may not resemble the actual one. These illustrations are for reference only.
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
2. Disconnect all power cords and cables.
3. Locate the rPGA 988B socket on the board.
4. Make sure the screw is in its unlock position. If it’s not, use a screwdriver to turn the screw to its unlock position.
Screw in unlocked position
5. Position the CPU above the socket.
The gold triangular mark on the CPU must align with pin 1 of the CPU socket.
Important:
Handle the CPU by its edges and avoid touching the pins.
Pin 1
6. Insert the CPU into the socket until it is seated in place. The CPU will fit in only one
orientation and can easily be inserted without exerting any force. Use a screwdriver to turn the screw to its lock position.
Important:
Do not force the CPU into the socket. Forcing the CPU into the socket may bend the pins and damage the CPU.
Gold triangular mark
Screw in locked position
14
www.d.comChapter 3 Hardware Installation
Page 15
Chapter 3
Connectors
CPU Fan Connector
Sense Power
Ground
Connect the CPU fan’s cable connector to the CPU fan connector on the board. The cooling fan will provide adequate airflow throughout the chassis to prevent overheating the CPU and board components.
BIOS Setting
“Module Board H/W Monitor” submenu in the Advanced menu of the BIOS will display the cur­rent speed of the cooling fan. Refer to chapter 3 of the manual for more information
1 3
.
COM Express Connectors
The COM Express connectors are used to interface the CR901-B COM Express board to a car­rier board. Connect the COM Express connectors (lcoated on the solder side of the board) to the COM Express connectors on the carrier board.
Refer to the “Installing CR901-B onto a Carrier Board” section for more information.
COM Express Connectors
Refer to the following pages for the pin functions of these connectors.
15
www.dfi .comChapter 3 Hardware Installation
Page 16
Chapter 3
COM Express Connectors
Row A Row B
A1 GND (FIXED) B1 GND (FIXED) A2 GBE0_MDI3- B2 GBE0_ACT# A3 GBE0_MDI3+ B3 LPC_FRAME# A4 GBE0_LINK100# B4 LPC_AD0 A5 GBE0_LINK1000# B5 LPC_AD1 A6 GBE0_MDI2- B6 LPC_AD2 A7 GBE0_MDI2+ B7 LPC_AD3 A8 GBE0_LINK# B8 LPC_DRQ0# A9 GBE0_MDI1- B9 LPC_DRQ1# A10 GBE0_MDI1+ B10 LPC_CLK A11 GND (FIXED) B11 GND (FIXED) A12 GBE0_MDI0- B12 PWRBTN# A13 GBE0_MDI0+ B13 SMB_CK A14 GBE0_CTREF B14 SMB_DAT A15 SLP_S3# B15 SMB_ALERT# A16 SATA0_TX+ B16 SATA1_TX+ A17 SATA0_TX- B17 SATA1_TX­A18 SLP_S4# B18 SUS_STAT# A19 SATA0_RX+ B19 SATA1_RX+ A20 SATA0_RX- B20 SATA1_RX­A21 GND (FIXED) B21 GND (FIXED) A22 SATA2_TX+ B22 SATA3_TX+ A23 SATA2_TX- B23 SATA3_TX­A24 SUS_S5# B24 PWR_OK A25 SATA2_RX+ B25 SATA3_RX+ A26 SATA2_RX- B26 SATA3_RX­A27 BATLOW# B27 WDT A28 (S)ATA_ACT# B28 AC/HDA _SDIN2 A29 AC/HDA_SYNC B29 AC/HDA _SDIN1 A30 AC/HDA _RST# B30 AC/HDA _SDIN0 A31 GND (FIXED) B31 GND (FIXED) A32 AC/HDA _BITCLK B32 SPKR A33 AC/HDA _SDOUT B33 I2C_CK A34 BIOS_DIS0# B34 I2C_DAT A35 THRMTRIP# B35 THRM# A36 USB6- B36 USB7­A37 USB6+ B37 USB7+ A38 USB_6_7_OC# B38 USB_4_5_OC# A39 USB4- B39 USB5­A40 USB4+ B40 USB5+ A41 GND (FIXED) B41 GND (FIXED) A42 USB2- B42 USB3­A43 USB2+ B43 USB3+ A44 USB_2_3_OC# B44 USB_0_1_OC# A45 USB0- B45 USB1­A46 USB0+ B46 USB1+ A47 VCC_RTC B47 EXCD1_PERST# A48 EXCD0_PERST# B48 EXCD1_CPPE# A49 EXCD0_CPPE# B49 SYS_RESET# A50 LPC_SERIRQ B50 CB_RESET#
16
Row A Row B
A51 GND (FIXED) B51 GND (FIXED) A52 PCIE_TX5+ B52 PCIE_RX5+ A53 PCIE_TX5- B53 PCIE_RX5­A54 GPI0 B54 GPO1 A55 PCIE_TX4+ B55 PCIE_RX4+ A56 PCIE_TX4- B56 PCIE_RX4­A57 GND B57 GPO2 A58 PCIE_TX3+ B58 PCIE_RX3+ A59 PCIE_TX3- B59 PCIE_RX3­A60 GND (FIXED) B60 GND (FIXED) A61 PCIE_TX2+ B61 PCIE_RX2+ A62 PCIE_TX2- B62 PCIE_RX2­A63 GPI1 B63 GPO3 A64 PCIE_TX1+ B64 PCIE_RX1+ A65 PCIE_TX1- B65 PCIE_RX1­A66 GND B66 WAKE0# A67 GPI2 B67 WAKE1# A68 PCIE_TX0+ B68 PCIE_RX0+ A69 PCIE_TX0- B69 PCIE_RX0-
A70 GND(FIXED) B70 GND (FIXED) A71 LVDS_A0+ B71 LVDS_B0+ A72 LVDS_A0- B72 LVDS_B0­A73 LVDS_A1+ B73 LVDS_B1+ A74 LVDS_A1- B74 LVDS_B1­A75 LVDS_A2+ B75 LVDS_B2+ A76 LVDS_A2- B76 LVDS_B2­A77 LVDS_VDD_EN B77 LVDS_B3+ A78 LVDS_A3+ B78 LVDS_B3­A79 LVDS_A3- B79 LVDS_BKLT_EN A80 GND (FIXED) B80 GND (FIXED) A81 LVDS_A_CK+ B81 LVDS_B_CK+ A82 LVDS_A_CK- B82 LVDS_B_CK-
A83 LVDS_I2C_CK B83 LVDS_BKLT_CTRL A84 LVDS_I2C_DAT B84 VCC_5V_SBY
A85 GPI3 B85 VCC_5V_SBY A86 RSVD B86 VCC_5V_SBY A87 RSVD B87 VCC_5V_SBY A88 PCIE0_CK_REF+ B88 BIOS_DIS1# A89 PCIE0_CK_REF- B89 VGA_RED A90 GND (FIXED) B90 GND (FIXED) A91 SPI_POWER B91 VGA_GRN A92 SPI_MISO B92 VGA_BLU A93 GPO0 B93 VGA_HSYNC A94 SPI_CLK B94 VGA_VSYNC A95 SPI_MOSI B95 VGA_I2C_CK A96 TPM_PP B96 VGA_I2C_DAT A97 TYPE10# B97 SPI_CS# A98 SER0_TX B98 RSVD A99 SER0_RX B99 RSVD A100 GND (FIXED) B100 GND (FIXED) A101 SER1_TX B101 FAN_PWMOUT A102 SER1_RX B102 FAN_TACHIN A103 LID# B103 SLEEP# A104 VCC_12V B104 VCC_12V A105 VCC_12V B105 VCC_12V A106 VCC_12V B106 VCC_12V A107 VCC_12V B107 VCC_12V A108 VCC_12V B108 VCC_12V A109 VCC_12V B109 VCC_12V A110 GND (FIXED) B110 GND (FIXED)
www.dfi .comChapter 3 Hardware Installation
Page 17
Chapter 3
Row C Row D
C1 GND (FIXED) D1 GND (FIXED) C2 GND D2 GND C3 USB_SSRX0- D3 USB_SSTX0­C4 USB_SSRX0+ D4 USB_SSTX0+ C5 GND D5 GND C6 USB_SSRX1- D6 USB_SSTX1­C7 USB_SSRX1+ D7 USB_SSTX1+ C8 GND D8 GND C9 USB_SSRX2- D9 USB_SSTX2­C10 USB_SSRX2+ D10 USB_SSTX2+ C11 GND (FIXED) D11 GND (FIXED) C12 USB_SSRX3- D12 USB_SSTX3­C13 USB_SSRX3+ D13 USB_SSTX3+ C14 GND D14 GND C15 DDI1_PAIR6+ D15 DDI1_CTRLCLK_AUX+ C16 DDI1_PAIR6- D16 DDI1_CTRLDATA_AUX­C17 RSVD D17 RSVD C18 RSVD D18 RSVD C19 PCIE_RX6+ D19 PCIE_TX6+ C20 PCIE_RX6- D20 PCIE_TX6­C21 GND (FIXED) D21 GND (FIXED) C22 PCIE_RX7+ D22 PCIE_TX7+ C23 PCIE_RX7- D23 PCIE_TX7­C24 DDI1_HPD D24 RSVD C25 DDI1_PAIR4+ D25 RSVD C26 DDI1_PAIR4- D26 DDI1_PAIR0+ C27 RSVD D27 DDI1_PAIR0­C28 RSVD D28 RSVD C29 DDI1_PAIR5+ D29 DDI1_PAIR1+ C30 DDI1_PAIR5- D30 DDI1_PAIR1­C31 GND (FIXED) D31 GND (FIXED) C32 DDI2_CTRLCLK_AUX+ D32 DDI1_PAIR2+ C33 DDI2_CTRLDATA_AUX- D33 DDI1_PAIR2­C34 DDI2_DDC_AUX_SEL D34 DDI1_DDC_AUX_SEL C35 RSVD D35 RSVD C36 DDI3_CTRLCLK_AUX+ D36 DDI1_PAIR3+ C37 DDI3_CTRLDATA_AUX- D37 DDI1_ P AIR3­C38 DDI3_DDC_AUX_SEL D38 RSVD C39 DDI3_PAIR0+ D39 DDI2_PAIR0+ C40 DDI3_PAIR0- D40 DDI2_PAIR0­C41 GND (FIXED) D41 GND (FIXED) C42 DDI3_PAIR1+ D42 DDI2_PAIR1+ C43 DDI3_PAIR1- D43 DDI2_PAIR1­C44 DDI3_HPD D44 DDI2_HPD C45 RSVD D45 RSVD C46 DDI3_PAIR2+ D46 DDI2_PAIR2+ C47 DDI3_PAIR2- D47 DDI2_PAIR2­C48 RSVD D48 RSVD C49 DDI3_PAIR3+ D49 DDI2_PAIR3+ C50 DDI3_PAIR3- D50 DDI2_PAIR3-
Row C Row D
C51 GND (FIXED) D51 GND (FIXED) C52 PEG_RX0+/ D52 PEG_TX0+ C53 PEG_RX0- D53 PEG_TX0­C54 TYPE0# D54 PEG_LANE_RV# C55 PEG_RX1+ D55 PEG_TX1+ C56 PEG_RX1- D56 PEG_TX1­C57 TYPE1# D57 TYPE2# C58 PEG_RX2+ D58 PEG_TX2+ C59 PEG_RX2- D59 PEG_TX2­C60 GND (FIXED) D60 GND (FIXED) C61 PEG_RX3+ D61 PEG_TX3+ C62 PEG_RX3- D62 PEG_TX3­C63 RSVD D63 RSVD
C64 RSVD D64 RSVD C65 PEG_RX4+ D65 PEG_TX4+
C66 PEG_RX4- D66 PEG_TX4­C67 NC D67 GND C68 PEG_RX5+ D68 PEG_TX5+ C69 PEG_RX5- D69 PEG_TX5­C70 GND (FIXED) D70 GND (FIXED) C71 PEG_RX6+ D71 PEG_TX6+ C72 PEG_RX6- D72 PEG_TX6­C73 GND D73 GND C74 PEG_RX7+ D74 PEG_TX7+ C75 PEG_RX7- D75 PEG_TX7­C76 GND D76 GND C77 RSVD D77 RSVD C78 PEG_RX8+ D78 PEG_TX8+ C79 PEG_RX8- D79 PEG_TX8­C80 GND (FIXED) D80 GND (FIXED) C81 PEG_RX9+ D81 PEG_TX9+ C82 PEG_RX9- D82 PEG_TX9-
C83 RSVD D83 RSVD C84 GND D84 GND
C85 PEG_RX10+ D85 PEG_TX10+ C86 PEG_RX10- D86 PEG_TX10­C87 GND D87 GND C88 PEG_RX11+ D88 PEG_TX11+ C89 PEG_RX11- D89 PEG_TX11­C90 GND (FIXED) D90 GND (FIXED) C91 PEG_RX12+ D91 PEG_TX12+ C92 PEG_RX12- D92 PEG_TX12­C93 GND D93 GND C94 PEG_RX13+ D94 PEG_TX13+ C95 PEG_RX13- D95 PEG_TX13­C96 GND D96 GND C97 RSVD D97 RSVD C98 PEG_RX14+ D98 PEG_TX14+ C99 PEG_RX14- D99 PEG_TX14­C100 GND (FIXED) D100 GND (FIXED) C101 PEG_RX15+ D101 PEG_TX15+ C102 PEG_RX15- D102 PEG_TX15­C103 GND D103 GND C104 VCC_12V D104 VCC_12V C105 VCC_12V D105 VCC_12V C106 VCC_12V D106 VCC_12V C107 VCC_12V D107 VCC_12V C108 VCC_12V D108 VCC_12V C109 VCC_12V D109 VCC_12V C110 GND (FIXED) D110 GND (FIXED)
17
www.dfi .comChapter 3 Hardware Installation
Page 18
Chapter 3
_
A
/
A
[3]
COM Express Connectors Signal Description
Pin Types I Input to the Module O Output from the Module I/O Bi-directional input / output signal OD Open drain output
C97/HDA Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description AC/HAD_RST# A30 O CMOS 3.3V Suspend/3.3V Reset output to CODEC, active low. AC/HDA_SYNC A29 O CMOS 3.3V/3.3V PU 1K to 3.3VSB Sample-synchronization signal to the CODEC(s). AC/HDA_BITCLK A32 I/O CMOS 3.3V/3.3V Serial data clock generated by the external CODEC(s). AC/HDA_SDOUT A33 O CMOS 3.3V/3.3V Serial TDM data output to the CODEC. AC/HDA_SDIN2 B28 I/O CMOS 3.3V Suspend/3.3V AC/HDA_SDIN1 B29 I/O CMOS 3.3V Suspend/3.3V AC/HDA_SDIN0 B30 I/O CMOS 3.3V Suspend/3.3V
Gigabit Ethernet Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description GBE0_MDI0+ A13 I/O Analog 3.3V max Suspend GBE0_MDI0- A12 I/O Analog 3.3V max Suspend GBE0_MDI1+ A10 I/O Analog 3.3V max Suspend GBE0_MDI1- A9 I/O Analog 3.3V max Suspend GBE0_MDI2+ A7 I/O Analog 3.3V max Suspend GBE0_MDI2- A6 I/O Analog 3.3V max Suspend GBE0_MDI3+ A3 I/O Analog 3.3V max Suspend
MDI3-
GBE0 GBE0_ACT# B2 OD CMOS 3.3V Suspend/3.3V Gigabit Ethernet Controller 0 activity indicator, active low. GBE0_LINK# A8 OD CMOS 3.3V Suspend/3.3V Gigabit Ethernet Controller 0 link indicator, active low. GBE0_LINK1000# A5 OD CMOS 3.3V Suspend/3.3V Gigabit Ethernet Controller 0 1000 Mbit / sec link indicator, active low.
2I
O Analog3.3V max Suspend
Serial TDM data inputs from up to 3 CODECs.
Gigabit Ethernet Controller 0: Media Dependent Interface Differential Pairs 0,1,2,3. The MDI can operate in 1000, 100 and 10 Mbit / sec modes. Some pairs are unused in some modes, per the following: 1000BASE-T 100BASE-TX 10BASE-T MDI[0]+/- B1_DA+/- TX+/- TX+/­ MDI[1]+/- B1_DB+/- RX+/- RX+/­ MDI[2]+/- B1_DC+/­ MDI
+/- B1_DD+/-
SATA Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description SATA0_TX+ A16 O SATA AC coupled on Module SATA0_TX- A17 O SATA AC coupled on Module SATA0_RX+ A19 I SATA AC coupled on Module SATA0_RX- A20 I SATA AC coupled on Module SATA1_TX+ B16 O SATA AC coupled on Module SATA1_TX- B17 O SATA AC coupled on Module SATA1_RX+ B19 I SATA AC coupled on Module SATA1_RX- B20 I SATA AC coupled on Module SATA2_TX+ A22 O SATA AC coupled on Module SATA2_TX- A23 O SATA AC coupled on Module SATA2_RX+ A25 I SATA AC coupled on Module SATA2_RX- A26 I SATA AC coupled on Module SATA3_TX+ B22 O SATA AC coupled on Module SATA3_TX- B23 O SATA AC coupled on Module SATA3_RX+ B25 I SATA AC coupled on Module SATA3_RX- B26 I SATA AC coupled on Module ATA_ACT# A28 I/O CMOS 3.3V / 3.3V PU 10K to 3.3V ATA (parallel and serial) or SAS activity indicator, active low.
Serial ATA or SAS Channel 0 transmit differential pair.
Serial ATA or SAS Channel 0 receive differential pair.
Serial ATA or SAS Channel 1 transmit differential pair.
Serial ATA or SAS Channel 1 receive differential pair.
Serial ATA or SAS Channel 2 transmit differential pair.
Serial ATA or SAS Channel 2 receive differential pair.
Serial ATA or SAS Channel 3 transmit differential pair.
Serial ATA or SAS Channel 3 receive differential pair.
18
www.dfi .comChapter 3 Hardware Installation
Page 19
Chapter 3
p
PCI Ex
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description PCIE_TX0+ A68 PCIE_TX0- A69 PCIE_RX0+ B68 PCIE_RX0- B69 PCIE_TX1+ A64 PCIE_TX1- A65 PCIE_RX1+ B64 PCIE_RX1- B65 PCIE_TX2+ A61 PCIE_TX2- A62 PCIE_RX2+ B61 PCIE_RX2- B62 PCIE_TX3+ A58 PCIE_TX3- A59 PCIE_RX3+ B58 PCIE_RX3- B59 PCIE_TX4+ A55 PCIE_TX4- A56 PCIE_RX4+ B55 PCIE_RX4- B56 PCIE_TX5+ A52 PCIE_TX5- A53 PCIE_RX5+ B52 PCIE_RX5- B53 PCIE_TX6+ D19 PCIE_TX6- D20 PCIE_RX6+ C19 PCIE_RX6- C20 PCIE_TX7+ D22 PCIE_TX7- D23 PCIE_RX7+ C22 PCIE_RX7- C23 PCIE0_CK_REF+ A88 PCIE0_CK_REF- A89
ress Lanes Signals Descriptions
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 0
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 0
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 1
I PCIE AC coupled off Module
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 2
I PCIE AC coupled off Module
O PCIE AC coupled on Module
I PCIE AC coupled off Module
O PCIE AC coupled on Module
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 4
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 5
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 5
O PCIE AC coupled on Module
I PCIE AC coupled off Module
O PCIE AC coupled on Module
I PCIE AC coupled off Module
O PCIE PCIE
PCI Express Differential Receive Pairs 1
PCI Express Differential Receive Pairs 2
PCI Express Differential Transmit Pairs 3
PCI Express Differential Receive Pairs 3
PCI Express Differential Transmit Pairs 4
PCI Express Differential Transmit Pairs 6
PCI Express Differential Receive Pairs 6 PCI Express Differential Transmit Pairs 7
(Optional with on board LAN, Default setting as NC) PCI Express Differential Receive Pairs 7 (Optional with on board LAN, Default setting as NC) Reference clock output for all PCI Express and PCI Express Graphics lanes.
19
www.dfi .comChapter 3 Hardware Installation
Page 20
Chapter 3
PEG Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description PEG_TX0+ D52 PEG_TX0- D53 PEG_RX0+ C52 PEG_RX0- C53 PEG_TX1+ D55 PEG_TX1- D56 PEG_RX1+ C55 PEG_RX1- C56 PEG_TX2+ D58 PEG_TX2- D59 PEG_RX2+ C58 PEG_RX2- C59 PEG_TX3+ D61 PEG_TX3- D62 PEG_RX3+ C61 PEG_RX3- C62 PEG_TX4+ D65 PEG_TX4- D66 PEG_RX4+ C65 PEG_RX4- C66 PEG_TX5+ D68 PEG_TX5- D69 PEG_RX5+ C68 PEG_RX5- C69 PEG_TX6+ D71 PEG_TX6- D72 PEG_RX6+ C71 PEG_RX6- C72 PEG_TX7+ D74 PEG_TX7- D75 PEG_RX7+ C74 PEG_RX7- C75 PEG_TX8+ D78 PEG_TX8- D79 PEG_RX8+ C78 PEG_RX8- C79 PEG_TX9+ D81 PEG_TX9- D82 PEG_RX9+ C81 PEG_RX9- C82 PEG_TX10+ D85 PEG_TX10- D86 PEG_RX10+ C85 PEG_RX10- C86 PEG_TX11+ D88 PEG_TX11- D89 PEG_RX11+ C88 PEG_RX11- C89 PEG_TX12+ D91 PEG_TX12- D92
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 0
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 0
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 1
I PCIE
O PCIE AC coupled on Module
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 2
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 3
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 3
O PCIE AC coupled on Module
I PCIE AC coupled off Module
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 5
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 5
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 6
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 6
O PCIE
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 7
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 8
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 8
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 9
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 9
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 10
I PCIE AC coupled off Module
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 11
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 11
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 12
AC coupled off Module PCI Express Graphics receive differential pairs 1
PCI Express Graphics transmit differential pairs 2
PCI Express Graphics transmit differential pairs 4
PCI Express Graphics receive differential pairs 4
AC coupled on Module PCI Express Graphics transmit differential pairs 7
PCI Express Graphics receive differential pairs 10
20
www.dfi .comChapter 3 Hardware Installation
Page 21
Chapter 3
PEG Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description PEG_RX12+ C91 PEG_RX12- C92 PEG_TX13+ D94 PEG_TX13- D95 PEG_RX13+ C94 PEG_RX13- C95 PEG_TX14+ D98 PEG_TX14- D99 PEG_RX14+ C98 PEG_RX14- C99 PEG_TX15+ D101 PEG_TX15- D102 PEG_RX15+ C101 PEG_RX15- C102
PEG_LANE_RV# D54 I CMOS 3.3V / 3.3V
ExpressCard Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description EXCD0_CPPE# A49 EXCD1_CPPE# B48 EXCD0_PERST# A48 EXCD1_PERST# B47
I PCIE AC coupled off Module
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 13
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 13
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 14
I PCIE AC coupled off Module
O PCIE AC coupled on Module PCI Express Graphics transmit differential pairs 15
I PCIE AC coupled off Module PCI Express Graphics receive differential pairs 15
I CMOS 3.3V /3.3V PU 10k to 3.3V PCI ExpressCard: PCI Express capable card request, active low, one per card
O CMOS 3.3V /3.3V PCI ExpressCard: reset, active low, one per card
PCI Express Graphics receive differential pairs 12
PCI Express Graphics receive differential pairs 14
PCI Express Graphics lane reversal input strap. Pull low on the Carrier board to reverse lane order.
21
www.dfi .comChapter 3 Hardware Installation
Page 22
Chapter 3
/
/
V
DDI Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description DDI1_PAIR0+/SDVO1_RED+ D26 DDI1_PAIR0­DDI1_PAIR1+/SDVO1_GRN+ D29 DDI1_PAIR1-/SDVO1_GRN- D30 DDI1_PAIR2+/SDVO1_BLU+ D32 DDI1_PAIR2-/SDVO1_BLU- D33 DDI1_PAIR3+/SDVO1_CK+ D36 DDI1_PAIR3-/SDVO1_CK- D37
DDI1_PAIR4+/SDVO1_INT+ C25 DDI1_PAIR4-/SDVO1_INT- C26
DDI1_PAIR5+/SDVO1_TVCLKIN+ C29 DDI1_PAIR5-/SDVO1_TVCLKIN- C30 DDI1_PAIR6+/SDVO1_FLDSTALL+ C15 DDI1_PAIR6-/SDVO1_FLDSTALL- C16
DDI1_CTRLCLK_AUX+/SDVO1_CTRLCLK D15
DDI1_CTRLCLK_AUX-/SDVO1_CTRLDATA D16 DDI1_HPD C24 I CMOS 3.3V / 3.3V DDI Hot-Plug Detect
DDI1_DDC_AUX_SEL D34 I CMOS 3.3V / 3.3V PD 1M to GND Selects the function of DDI1_CTRLCLK_AUX+ and DDI1_CTRLDATA_AUX-. DDI2_PAIR0+ D39 DDI2_PAIR0- D40 DDI2_PAIR1+ D42 DDI2_PAIR1- D43 DDI2_PAIR2+ D46 DDI2_PAIR2- D47 DDI2_PAIR3+ D49 DDI2_PAIR3- D50
DDI2_CTRLCLK_AUX+ C32
DDI2_CTRLCLK_AUX- C33 DDI3_HPD D44 I CMOS 3.3V / 3.3V DDI Hot-Plug Detect
DDI3_DDC_AUX_SEL C34 I CMOS 3.3V / 3.3V PD 1M to GND Selects the function of DDI2_CTRLCLK_AUX+ and DDI2_CTRLDATA_AUX-. DDI3_PAIR0+ C39 DDI3_PAIR0- C40 DDI3_PAIR1+ C42 DDI3_PAIR1- C43 DDI3_PAIR2+ C46 DDI3_PAIR2- C47 DDI3_PAIR3+ C49 DDI3_PAIR3- C50
DDI3_CTRLCLK_AUX+ C36
DDI3_CTRLCLK_AUX- C37 DDI3_HPD C44 I CMOS 3.3V / 3.3V DDI Hot-Plug Detect
DDI3_DDC_AUX_SEL C38 I CMOS 3.3V / 3.3V PD 1M to GND Selects the function of DDI3_CTRLCLK_AUX+ and DDI3_CTRLDATA_AUX-.
SDVO1_RED- D27
O PCIE AC coupled off Module DDI 1 Pair 0 differential pairs/Serial Digital Video B red output differential pair
O PCIE AC coupled off Module DDI 1 Pair 1 differential pairs/Serial Digital Video B green output differential pair
O PCIE
O PCIE AC coupled off Module DDI 1 Pair 3 differential pairs/Serial Digital Video B clock output differential pair.
I PCIE
I PCIE AC coupled off Module Serial Digital Video TVOUT synchronization clock input differential pair.
I PCIE I/O PCIE AC coupled on Module DP AUX+ function if DDI1_DDC_AUX_SEL is no connect
I
O OD CMOS 3.3V / 3.3 I/O PCIE AC coupled on Module DP AUX- function if DDI1_DDC_AUX_SEL is no connect I/O OD CMOS 3.3V / 3.3V HDMI/DVI I2C CTRLDATA if DDI1_DDC_AUX_SEL is pulled high
O PCIE AC coupled off Module
O PCIE AC coupled off Module DDI 2 Pair 1 differential pairs
O PCIE AC coupled off Module DDI 2 Pair 2 differential pairs
O PCIE AC coupled off Module DDI 2 Pair 3 differential pairs I/O PCIE AC coupled on Module DP AUX+ function if DDI2_DDC_AUX_SEL is no connect
I/O OD CMOS 3.3V / 3.3V HDMI/DVI I2C CTRLCLK if DDI2_DDC_AUX_SEL is pulled high I/O PCIE AC coupled on Module DP AUX- function if DDI2_DDC_AUX_SEL is no connect I/O OD CMOS 3.3V / 3.3V HDMI/DVI I2C CTRLDATA if DDI2_DDC_AUX_SEL is pulled high
O PCIE AC coupled off Module DDI 3 Pair 0 differential pairs
O PCIE
O PCIE AC coupled off Module
O PCIE AC coupled off Module DDI 3 Pair 3 differential pairs I/O PCIE AC coupled on Module DP AUX+ function if DDI3_DDC_AUX_SEL is no connect
I/O OD CMOS 3.3V / 3.3V HDMI/DVI I2C CTRLCLK if DDI3_DDC_AUX_SEL is pulled high I/O PCIE AC coupled on Module DP AUX- function if DDI3_DDC_AUX_SEL is no connect
I/O OD CMOS 3.3V / 3.3V HDMI/DVI I2C CTRLDATA if DDI3_DDC_AUX_SEL is pulled high
AC coupled off Module DDI 1 Pair 2 differential pairs/Serial Digital Video B blue output differential pair
AC coupled off Module Serial Digital Video B interrupt input differential pair.
AC coupled off Module Serial Digital Video Field Stall input differential pair.
HDMI/DVI I2C CTRLCLK if DDI1_DDC_AUX_SEL is pulled high
DDI 2 Pair 0 differential pairs
AC coupled off Module DDI 3 Pair 1 differential pairs
DDI 3 Pair 2 differential pairs
22
www.dfi .comChapter 3 Hardware Installation
Page 23
Chapter 3
p
p
p
p
USB Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description USB0+ A46 USB0- A45 USB1+ B46 USB1- B45 USB2+ A43 USB2- A42 USB3+ B43 USB3- B42 USB4+ A40 USB4- A39 USB5+ B40 USB5- B39 USB6+ A37 USB6- A36 USB7+ B37
USB7- B36
USB_0_1_OC# B44 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3VSB
USB_2_3_OC# A44 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3VSB
USB_4_5_OC# B38 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3VSB
USB_6_7_OC# A38 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3VSB
USB_SSTX0+ D4 USB_SSTX0- D3 USB_SSRX0+ C4 USB_SSRX0- C3 USB_SSTX1+ D7 USB_SSTX1- D6 USB_SSRX1+ C7 USB_SSRX1- C6 USB_SSTX2+ D10 USB_SSTX2- D9 USB_SSRX2+ C10 USB_SSRX2- C9 USB_SSTX3+ D13 USB_SSTX3- D12 USB_SSRX3+ C13 USB_SSRX3- C12
I/O USB 3.3V Suspend/3.3V USB differential pairs 0
I/O USB 3.3V Suspend/3.3V USB differential pairs 1
I/O USB 3.3V Suspend/3.3V USB differential pairs 2
I/O USB 3.3V Suspend/3.3V USB differential pairs 3
I/O USB
I/O USB 3.3V Suspend/3.3V USB differential pairs 5
I/O USB 3.3V Suspend/3.3V USB differential pairs 6
I/O USB 3.3V Suspend/3.3V
O PCIE AC coupled on Module Additional transmit signal differential pairs for the SuperSpeed USB data path.
I PCIE AC coupled off Modul
O PCIE AC coupled on Module Additional transmit signal differential pairs for the SuperSpeed USB data path.
I PCIE AC coupled off Modul Additional receive signal differential pairs for the SuperSpeed USB data path.
O PCIE AC coupled on Module Additional transmit signal differential pairs for the SuperSpeed USB data path.
I PCIE AC coupled off Modul Additional receive signal differential pairs for the SuperSpeed USB data path.
O PCIE AC coupled on Module Additional transmit signal differential pairs for the SuperSpeed USB data path.
I PCIE AC coupled off Modul Additional receive signal differential pairs for the SuperSpeed USB data path.
3.3V Suspend/3.3V USB differential pairs 4
USB differential pairs 7, USB7 may be configured as a USB client or as a host, or both, at the Module designer's discretion.(CR901-B default set as a host)
USB over-current sense, USB channels 0 and 1. A pull-up for this line shall be present on the Module. An open drain driver from a USB current monitor on the Carrier Board may drive this line low. Do not
ull this line high on the Carrier Board. USB over-current sense, USB channels 2 and 3. A pull-up for this line shall be present on the Module. An open drain driver from a USB current monitor on the Carrier Board may drive this line low. Do not
ull this line high on the Carrier Board. USB over-current sense, USB channels 4 and 5. A pull-up for this line
shall be present on the Module. An open drain driver from a USB current monitor on the Carrier Board may drive this line low. Do not
ull this line high on the Carrier Board. USB over-current sense, USB channels 6 and 7. A pull-up for this line shall be present on the Module. An open drain driver from a USB current monitor on the Carrier Board may drive this line low. Do not
ull this line high on the Carrier Board.
Additional receive signal differential pairs for the SuperSpeed USB data path.
23
www.dfi .comChapter 3 Hardware Installation
Page 24
Chapter 3
LVDS Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description LVDS_A0+ A71 LVDS_A0- A72 LVDS_A1+ A73 LVDS_A1- A74 LVDS_A2+ A75 LVDS_A2- A76 LVDS_A3+ A78 LVDS_A3- A79 LVDS_A_CK+ A81 LVDS_A_CK- A82 LVDS_B0+ B71 LVDS_B0- B72 LVDS_B1+ B73 LVDS_B1- B74 LVDS_B2+ B75 LVDS_B2- B76 LVDS_B3+ B77 LVDS_B3- B78 LVDS_B_CK+ B81 LVDS_B_CK- B82 LVDS_VDD_EN A77 O CMOS 3.3V / 3.3V PD 100K to GND LVDS panel power enable LVDS_BKLT_EN B79 O CMOS 3.3V / 3.3V PD 100K to GND LVDS panel backlight enable LVDS_BKLT_CTRL B83 O CMOS 3.3V / 3.3V PD 100K to GND LVDS panel backlight brightness control LVDS_I2C_CK A83 I/O OD CMOS 3.3V / 3.3V PU 2.2K to 3.3V I2C clock output for LVDS display use LVDS_I2C_DAT A84 I/O OD CMOS 3.3V / 3.3V PU 2.2K to 3.3V I2C data line for LVDS display use
O LVDS LVDS
O LVDS
O LVDS LVDS
O LVDS LVDS
O LVDS LVDS
O LVDS LVDS
O LVDS LVDS
O LVDS LVDS
O LVDS LVDS
LVDS
LVDS Channel A differential pairs
LVDS Channel A differential clockO LVDS LVDS
LVDS Channel B differential pairs
LVDS Channel B differential clock
LPC Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description LPC_AD0 B4 LPC_AD1 B5 LPC_AD2 B6 LPC_AD3 B7 LPC_FRAME# B3 O CMOS 3.3V / 3.3V LPC frame indicates the start of an LPC cycle LPC_DRQ0# B8 LPC_DRQ1# B9 LPC_SERIRQ A50 I/O CMOS 3.3V / 3.3V PU 10K to 3.3V LPC serial interrupt LPC_CLK B10 O CMOS 3.3V / 3.3V LPC clock output - 33MHz nominal
I/O CMOS 3.3V / 3.3V
I CMOS 3.3V / 3.3V LPC serial DMA request
LPC multiplexed address, command and data bus
24
www.dfi .comChapter 3 Hardware Installation
Page 25
Chapter 3
_
V
_
A
/
.
V
g
g
g
SPI Si
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description SPI SPI_MISO A92 I CMOS 3.3V Suspend/3.3V Data in to Module from Carrier SPI SPI_MOSI A95 O CMOS 3.3V Suspend/3.3V Data out from Module to Carrier SPI SPI_CLK A94 O CMOS 3.3V Suspend/3.3V Clock from Module to Carrier SPI
SPI_POWER A91 O 3.3V Suspend/3.3V
BIOS
BIOS_DIS1# B88
nals Descriptions
CS# B97 O CMOS 3.3V Suspend/3.3
DIS0#
34
I CMOS NA
Chip select for Carrier Board SPI - may be sourced from chipset SPI0 or SPI1
Power supply for Carrier Board SPI – sourced from Module – nominally
3.3V. The Module shall provide a minimum of 100mA on SPI_POWER. Carriers shall use less than 100mA of SPI_POWER. SPI_POWER shall only be used to power SPI devices on the Carrier
Selection straps to determine the BIOS boot device. The Carrier should only float these or pull them low, please refer to COM Express Module Base Specification Revision 2.1 for strapping options of BIOS disable signals.
GA Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description VGA_RED B89 O Analog Analog PD 150R Red for monitor. Analog output VGA_GRN B91 O Analog Analog PD 150R Green for monitor. Analog output VGA_BLU B92 O Analog Analog PD 150R Blue for monitor. Analog output VGA_HSYNC B93 O CMOS 3.3V / 3.3V Horizontal sync output to VGA monitor VGA_VSYNC B94 O CMOS 3.3V / 3.3V Vertical sync output to VGA monitor VGA_I2C_CK B95 I/O OD CMOS 3.3V / 3.3V PD 2.2K to 3.3V DDC clock line (I2C port dedicated to identify VGA monitor capabilities) VGA_I2C_DAT B96 I/O OD CMOS 3.3V / 3.3V PD 2.2K to 3.3V DDC data line.
Serial Interface Si
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description SER0_TX A98 O CMOS 3.3V/5V General purpose serial port 0 transmitter
SER0_RX A99 I CMOS 3.3V/5V General purpose serial port 0 receiver SER1_TX A101 O CMOS 3.3V/5V General purpose serial port 1 transmitter
nals Descriptions
SER1_RX A102 I CMOS 3.3V/5V General purpose serial port 1 receiver
Miscellaneous Si
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description I2C_CK B33 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB General purpose I2C port clock output I2C_DAT B34 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB General purpose I2C port data I/O line
SPKR B32 O CMOS 3.3V / 3.3V
WDT B27 O CMOS 3.3V FAN_PWNOUT B101 O OD CMOS 3.3V / 12V Fan speed control. Uses the Pulse Width Modulation (PWM) technique to control the fan's RPM. FAN_TACHIN B102 I OD CMOS 3.3V / 12V PU 10K to 3.3V Fan tachometer input for a fan with a two pulse output.
TPM_PP A96 I CMOS 3.3V / 3.3V
nal Descriptions
Output for audio enunciator - the "speaker" in PC-AT systems. This port provides the PC beep signal and is mostly intended for debugging purposes.
3.3V Output indicating that a watchdog time-out event has occurred
Trusted Platform Module (TPM) Physical Presence pin. Active high. TPM chip has an internal pull down. This signal is used to indicate Physical Presence to the TPM.
25
www.dfi .comChapter 3 Hardware Installation
Page 26
Chapter 3
Power and System Management Signals Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description
PWRBTN# B12 I CMOS 3.3V Suspend/3.3V
SYS_RESET# B49 I CMOS 3.3V Suspend/3.3V
CB_RESET# B50 O CMOS 3.3V Suspend/3.3V
PWR_OK B24 I CMOS 3.3V / 3.3V
SUS_STAT# B18 O CMOS 3.3V Suspend/3.3V Indicates imminent suspend operation; used to notify LPC devices.
SUS_S3# A15 O CMOS 3.3V Suspend/3.3V
SUS_S4# A18 O CMOS 3.3V Suspend/3.3V Indicates system is in Suspend to Disk state. Active low output. SUS_S5# A24 O CMOS 3.3V Suspend/3.3V Indicates system is in Soft Off state.
WAKE0# B66 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB PCI Express wake up signal. WAKE1# B67 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB
BATLOW# A27 I CMOS 3.3V Suspend/ 3.3V PU 10K to 3.3VSB
LID# A103 I OD CMOS 3.3V Suspend/12V PU 10K to 3.3VSB LID switch. Low active signal used by the ACPI operating system for a LID switch. SLEEP# B103 I OD CMOS 3.3V Suspend/12V PU 10K to 3.3VSB
THRM# B35 I CMOS 3.3V / 3.3V PU 10K to 3.3V Input from off-Module temp sensor indicating an over-temp situation. THRMTRIP# A35 O CMOS 3.3V / 3.3V PU 10K to 3.3V Active low output indicating that the CPU has entered thermal shutdown. SMB_CK B13 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB System Management Bus bidirectional clock line.
SMB_DAT B14 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB System Management Bus bidirectional data line. SMB_ALERT# B15 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB
A falling edge creates a power button event. Power button events can be used to bring a system out of S5 soft off and other suspend states, as well as powering the system down. Reset button input. Active low request for Module to reset and reboot. May be falling edge sensitive. For situations when SYS_RESET# is not able to reestablish control of the system, PWR_OK or a power cycle may be used.
Reset output from Module to Carrier Board. Active low. Issued by Module chipset and may result from a low SYS_RESET# input, a low PWR_OK input, a VCC_12V power input that falls below the minimum specification, a watchdog timeout, or may be initiated by the Module software.
Power OK from main power supply. A high value indicates that the power is good. This signal can be used to hold off Module startup to allow Carrier based FPGAs or other configurable devices time to be programmed.
Indicates system is in Suspend to RAM state. Active low output. An inverted copy of SUS_S3# on the Carrier Board may be used to enable the non-standby power on a typical ATX supply.
General purpose wake up signal. May be used to implement wake-up on PS2 keyboard or mouse activity.
Indicates that external battery is low. This port provides a battery-low signal to the Module for orderly transitioning to power saving or power cut-off ACPI modes.
Sleep button. Low active signal used by the ACPI operating system to bring the system to sleep state or to wake it up again.
System Management Bus Alert – active low input can be used to generate an SMI# (System Management Interrupt) or to wake the system.
26
www.dfi .comChapter 3 Hardware Installation
Page 27
Chapter 3
A
A
,
80, D84, D87,
Power and GND Signal Descriptions
Signal Pin# Pin Type Pwr Rail /Tolerance PU/PD Description
VCC_12V
VCC_5V_SBY B84~B87 Power
VCC_RTC A47 Power Real-time clock circuit-power input. Nominally +3.0V.
GND
104~A109 B104~B109 C104~C109
~
1, A11, A21, A31 A41, A51, A57, A60, A66, A70, A80, A90, A100, A110, B1, B11, B21 ,B31, B41, B51, B60, B70, B80, B90, B100, B110, C1, C2, C5, C8, C11, C14, C21, C31, C41, C51, C60, C70, C73, C76, C80, C84, C87, C90, C93, C96, C100, C103, C110, D1, D2, D5, D8, D11, D14, D21, D31, D51, D60, D67, D70, D73, D76, D
Power Primary power input: +12V nominal. All available VCC_12V pins on the connector(s) shall be used.
Standby power input: +5.0V nominal. If VCC5_SBY is used, all available VCC_5V_SBY pins on the connector(s) shall be used. Only used for standby and suspend functions. May be left unconnected if these functions are not used in the system design.
Ground - DC power and signal and AC signal return path.
Power
All available GND connector pins shall be used and tied to Carrier Board GND plane.
27
www.dfi .comChapter 3 Hardware Installation
Page 28
Chapter 3
Standby Power LED
Standby
Power LED
This LED will light when the system is in the standby mode.
Cooling Option
Heat Sink with Cooling Fan
Top View of the Heat Sink
1
Bottom View of the Heat Sink
3
• “1”, “2” and “3” denote the locations of the thermal pads designed to contact the corresponding components that are on CR901-B.
Important:
Remove the plastic covering from the thermal pads prior to mounting the heat sink onto CR901-B.
28
2
www.dfi .comChapter 3 Hardware Installation
Page 29
Chapter 3
Installing CR901-B onto a Carrier Board
Important:
The carrier board (COM331-B) used in this section is for reference purpose only and may not resemble your carrier board. These illustrations are mainly to guide you on how to install CR901-B onto the carrier board of your choice.
To Download COM331-B Datasheet and Manual
1. Use the provided screw to install the heatsink onto the module. First align the mounting hole of the heatsink with the mounting hole of the module and then from the bottom side of the module, secure them with the provided screw. The module and heatsink as sembly should look like the one shown below.
bottom side of heat sink
Mounting hole
Mounting hol
e
2. Now install the module and heatsink assembly onto the carrier board. The photo below shows the locations of the mounting holes on carrier board.
Mounting hole
3. Insert the provided mounting screws into the mounting holes - from the bottom through the top of the carrier board.
Mounting screws
Top view
Bottom view
Mounting screw
29
www.dfi .comChapter 3 Hardware Installation
Page 30
Chapter 3
4. While supporting the mounting screw at the bottom, from the top side of the board, fasten a bolt into the screw.
Bolts
5. The photo below shows the solder side of the board with the screws already fixed in place.
Mounting screw
6. The photo below shows the component side of the board with the bolts already fixed in place.
Bolts
7. Position the heat sink on top of CR901-B with the heat sink’s mounting holes aligned with CR901-B’s mounting holes. Insert one of the provided long screws into the mounting hole shown in the photo below.
Mounting hole
Long screw
30
www.dfi .comChapter 3 Hardware Installation
Page 31
Chapter 3
8. From the bottom of the board, fasten the provided bolt into the screw and then connect the cooling fan’s cable to the fan connector on CR901-B.
Fan connector
Bolt
9. Grasping CR901-B by its edges, position it on top of the carrier board with its mounting holes aligned with the bolts on the carrier board. This will also align the COM Express connectors of the two boards to each other.
COM Express connec­tors on CR901-B
10. Press CR901-B down firmly until it is completely seated on the COM Express connectors of the carrier board.
CR901-B
Carrier board
11. Use the provided mounting screws to secure CR901-B with heat sink to the carrier board. The photo below shows the locations of the long/short mounting screws.
Long screws
Short screws
COM Express connectors on the carrier board
31
www.dfi .comChapter 3 Hardware Installation
Page 32
Chapter 4
Chapter 4 - BIOS Setup Overview
The BIOS is a program that takes care of the basic level of communication between the CPU and peripherals. It contains codes for various advanced features found in this system board. The BIOS allows you to configure the system and save the configuration in a battery-backed CMOS so that the data retains even when the power is off. In general, the information stored in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been made such as a hard drive replaced or a device added. It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need to install a new CMOS battery and reconfigure the BIOS settings.
Legends
KEYs Function
Right and Left Arrows Moves the highlight left or right to select a
menu.
Up and Down Arrows Moves the highlight up or down between
submenus or fi elds.
Note:
The BIOS is constantly updated to improve the performance of the system board; therefore the BIOS screens in this chapter may not appear the same as the actual one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are key­board commands. The commands are available at the right side of each setup screen.
The BIOS Setup Utility does not require an operating system to run. After you power up the system, the BIOS message appears on the screen and the memory count begins. After the memory test, the message “Press DEL to run setup” will appear on the screen. If the message disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
<Esc> Exits to the BIOS setup utility
+ (plus key) Scrolls forward through the values or
options of the hightlighted fi eld.
- (minus key) Scolls backward through the values or options of the hightlighted fi eld.
Tab Select a fi eld <F1> Displays general help <Enter> Press <Enter> to enter the highlighted
submenu
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.
Submenu
When ““ appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press <Enter>.
32
www.dfi .comChapter 4 BIOS Setup
Page 33
Chapter 4
AMI BIOS Setup Utility Advanced Main
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Main
BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date and Time
System Date
System Time
Access Level
System Date
The date format is <day>, <month>, <date>, <year>. Day displays a day, from Sun­day to Saturday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1980 to 2099.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Boot Security
American Megatrends
4.6.5.3 UEFI 2.3; PI 1.2 1APTJ 0.18 x64 03/30/2012 18:25:14
[Thur 01/01/2009] [22:17:37]
Administraor
Save & ExitChipset
Set the date. Use Tab to switch between date ele­ments.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.
Important: Setting incorrect field values may cause the system to malfunction
Main
ACPI Settings
Trusted Computing
PC Health Status
CPU Con guration
SATA Con guration
Intel TXT(LT) Con guration
PCH-FW Con guration
Intel(R) Anti-Theif Technology Con guration
USB Con guration
CPU PPM Con guration
WatchDog Con guration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Save & ExitChipset Boot Security
System ACPI Parameters.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
33
www.dfi .comChapter 4 BIOS Setup
Page 34
Chapter 4
ACPI Power Management Configuration
This section is used to configure the ACPI Power Management.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
ACPI Settings
Enable ACPI Auto Confi guration
ACPI Sleep State Resume by PME
Resume by RTC Alarm
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Disabled]
[S3 (Suspend to RAM) ] [Disabled]
[Disabled]
Enables or disables BIOS ACPI Auto Confi guration.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
ACPI Sleep State
Selects the highest ACPI sleep state the system will enter when the Suspend button is pressed.
S1(POS) Enables the Power On Suspend function. S3(STR) Enables the Suspend to RAM function.
Trusted Computing (optional)
This section configures settings relevant to Trusted Computing innovations.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Confi guration
TPM Support
Current Status Information Support Turned Off
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Disabled]
Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
TPM Support
Enables or Disables TPM. O.S. will not show TPM. Resetting the platform is required.
Resume by PME
Enable this field to use the PME signal to wake up the system (via PCIE and onboard (LAN).
Resume by RTC Alarm
When Enabled, the system uses the RTC to generate a wakeup event.
34
www.dfi .comChapter 4 BIOS Setup
Page 35
Chapter 4
PC Health Status
This section displays hardware health monitor.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
System Hardware Monitor CPU SmartFan CPU Temperature CPU FAN Speed System FAN Speed VCore Vgfs DDR +1.05V CPU VCCSA
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Enabled]
: +60 C : 4968 RPM : N/A : +0.958 V : N/A : +1.519 V : +0.997 V : +0.859 V
Enable/ Disable CPU SmartFan
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
CPU Configuration
This section is used to configure the CPU. It will also display the detected CPU information.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Confi guration Intel (R) Core (TM) i7-3610QE CPU @ 2.30GHz
CPU Signature Microcode Patch Max CPU Speed Min CPU Speed CPU Speed Processor Cores Intel HT Technology Intel VT-X Technology Intel SMX Technology 64 bit
L1 Data Cache L1 Code Cache L2 Cache L3 Cache
Hyper-threading
Active Process Core Limit CUPID Maximum Intel Virtualization Technology
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
306a8 7 2300 MHz 1200 MHz 2300 MHz 4 Supported Supported Supported Supported
32 kB x4 32 kB x4 256 kB x4 6144 kB
[Enabled]
[All] [Disabled] [Disabled]
Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Hyper-threading
Enable this field for Windows XP and Linux which are optimized for Hyper-Threading technology. Select disabled for other OSes not optimized for Hyper-Threading tech­nology. When disabled, only one thread per enabled core is enabled.
Active Process Core
Number of cores to enable in each processor package
Limit CUPID Maximum
The CPUID instruction of some newer CPUs will return a value greater than 3. The default is Disabled because this problem does not exist in the Windows series operating systems. If you are using an operating system other than Windows, this problem may occur. To avoid this problem, enable this field to limit the return value to 3 or less than 3
.
Intel Virtualization Technology
When this field is set to Enabled, the VMM can utilize the additional hardware capa­bilities provided by Vanderpool Technology.
35
www.dfi .comChapter 4 BIOS Setup
Page 36
Chapter 4
SATA Configuration
This section is used to configure SATA functions.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
SATA Controller(s)
SATA Mode Selection SATA Controller Speed
Serial ATA Port 0 Software Preserve Port 0
Hot Plug External SATA SATA Device Type Spin Up Device
Serial ATA Port 1 Software Preserve
Port 1 Hot Plug External SATA SATA Device Type Spin Up Device
Serial ATA Port 2 Software Preserve Port 2
Hot Plug External SATA Spin Up Device
Serial ATA Port 3 Software Preserve Port 3
Hot Plug External SATA Spin Up Device
Serial ATA Port 4 Software Preserve Port 4
Hot Plug External SATA Spin Up Device
Version 2.02.1205. Copyright (C) 2010 American Megatrends, Inc.
[Enabled]
[AHCI] [Gen3]
WDC WD2500BEVS (250.0 Supported
[Enabled] [Disabled] [Disabled] [Hard Disk Driver] [Disabled]
Empty Unknown
[Enabled] [Disabled] [Disabled] [Hard Disk Driver] [Disabled]
ATAPI iHOS10 ATAPI N/A
[Enabled] [Disabled] [Disabled] [Disabled]
Empty Unknown
[Enabled] [Disabled] [Disabled] [Disabled]
GLS85LS1004P (4.0GB Supported
[Enabled] [Disabled] [Disabled] [Disabled]
SATA Controller(s)
Enable or disable SATA
Device.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Intel TXT (LT) Configuration
This section is used to configure the Intel Trusted Execution technology.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel Trusted Execution Technology Confi guration Intel TXT support only can be enabled/disabled if SMX is
enabled. VT and VT-d support must also be enabled prior to TXT. Secure Mode Extension (SMX) Intel TXT(LT) Support
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enabled [Disabled]
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Secure Mode Extensions (SMX)
The options are Enabled and Disabled.
Intel TXT(LT) Support
The options are Enabled and Disabled (Default).
This field is used to enable or disable the Serial ATA channels.
SATA Mode Selection
IDE Mode
This option configures the Serial ATA drives as Parallel ATA storage devices.
AHCI Mode This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Inter­face).
RAID Mode This option allows you to create RAID or Intel Matrix Storage configuration on Serial ATA devices.
SATA Controller Speed
It indicates the maximun speed which the SATA controller can support.
36
www.dfi .comChapter 4 BIOS Setup
Page 37
Chapter 4
PCH-FW Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
ME FW Version ME Firmware Mode ME Firmware Type ME Firmware SKU
Firmware Update Con guration
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
8.0.1.1399 Normal Mode Full Sku Firmware 5MB
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Intel Anti-Theft Configuration
This section is used to disable the PC at the hardware level in the event of loss or theft.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel Anti-Theft Technology Confi guration
Intel Anti-Theft Technology
Intel Anti-Theft Technology Recove
Enter Intel AT Suspend Mode
[Disabled]
3
[Disabled]
Enable/Disable Intel AT in BIOS for testing only.
USB Configuration
This section is used to configure USB.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
USB Confi guration USB Devices:
2 Drivers, 1 Keyboard, 1 mouse, 2 Hubs
Legacy USB Support
USB3.0 Support XHCI Hand-off EHCI Hand-off
USB hardware delays and time-outs:
USB transfer time-out Device reset time-out Device power-up delay
Mass Storage Devices:
Seagate FreeAgent GoFlex 214 TEAC USB UF000x 0.00
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Legacy USB Support
Enabled
Enables legacy USB.
Auto Disables support for legacy when no USB devices are connected.
Disabled Keeps USB devices available only for EFI applications.
[Enabled]
[Enabled] [Enabled] [Disabled]
[20 sec] [20 sec] [Auto]
[Auto] [Auto]
Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Intel Anti-Theft Technology
The options are Enabled and Disabled.
Enter Intel AT Suspend Mode
The options are Enabled and Disabled (Default).
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
XHCI Hand-off
This is a workaround for OSes that does not support XHCI hand-off. The XHCI own­ership change should be claimed by the XHCI driver.
EHCI Hand-off
This is a workaround for OSes that does not support EHCI hand-off. The EHCI own­ership change should be claimed by the EHCI driver.
USB transfer time-out
The time-out value for Bulk and Interrupt transfers.
Device reset time-out
Selects the USB mass storage device start unit command timeout.
37
www.dfi .comChapter 4 BIOS Setup
Page 38
Chapter 4
Device power-up delay
Maximum time the device will take before it properly reports itself to the Host Controller. “Auto” uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.
CPU PPM Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Sandybridge PPM Confi guration
EIST
Turbo Mode
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Enabled]
[Enabled]
Enable/Disable Intel SpeedStep
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
EIST
This field is used to enable or disable the Intel Enhanced SpeedStep Technology.
WatchDog Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
WatchDog1 function
WatchDog2 function
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
WatchDog function
This field is used to enable or disable the Watchdog timer function.
Watchdog 1 function
For CR901-B module board (Reset CR901-B by hardware)
Watchdog 2 function
[Disabled]
[Disabled]
Enable/Disable IT8518 WatchDog Timer.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Turbo Mode
The options are Enabled and Disabled.
For carrier board usage.
38
www.dfi .comChapter 4 BIOS Setup
Page 39
Chapter 4
Chipset
Configures relevant chipset functions.
Main

PCH-IO Confi guration

System Agent (SA) Confi guration

NB PCIe Bifurcation Confi guration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Chipset
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Boot Security
Save & Exit
PCH Parameters
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
PCH-IO Configuration
Intel PCH RC Version Intel PCH SKU Name Intel PCH Rev ID

PCI Express Confi guration
USB Confi guration

PCH Azalia Confi guration
PCH LAN Controller Wake on LAN
After G3
PCH LAN Controller
Enables or disables the PCH LAN Controller.
Wake on LAN Enable
Set this field to Enabled to wake up the system via the onboard LAN or via a LAN card that supports the remote wake up function.
After G3
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
1.0.0.0 QM77 04/C1
[Enabled] [Enabled]
[Power on]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PCI Express Coniguration settings.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Power Off / WOL Power-on the system via WOL after G3.
Power On
Power-on the system after G3
39
.
www.dfi .comChapter 4 BIOS Setup
Page 40
Chapter 4
PCI Express Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
PCI Express Confi guration
PCI Express Clock Gating
PCI Express Root Port 1
PCI Express Root Port 5
PCI Express Root Port 6
PCI Express Root Port 7
PCIE Port 8 is assigned to LAN
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Enabled]
Enable or Disable PCI Express Clock Gating for each root port.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
PCI Express Clock Gating
Enables or disables PCI Express Clock Gating for each root port.
PCI Express Root Port 1, port 5 to PCI Express Root Port 7
Controls the PCI Express Root Port.
USB Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
USB Confi guration
XHCI Mode
HS Port #1 Switchable HS Port #2 Switchable HS Port #3 Switchable HS Port #4 Switchable xHCI Streams
EHCI1 EHCI2
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Smart Auto]
[Enabled] [Enabled] [Enabled] [Enabled] [Enabled]
[Enabled] [Enabled]
Mode of operation of XHCI controller.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
xHCI Mode
Mode of operation of xHCI controller. Options are Smart Auto, Auto, Enabled, Disabled.
EHCI1 and EHCI2
These fields are used to enable or disable USB 2.0
.
40
www.dfi .comChapter 4 BIOS Setup
Page 41
Chapter 4
PCH Azalia Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
PCH Azalia Confi guration
Azalia
Azalia Internal HDMI Codec

Azalia HDMI Codec port B Azalia HDMI Codec port C Azalia HDMI Codec port D
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
[Auto]
[Enabled] [Enabled] [Disabled] [Enabled]
Azalia internal HDMI codec
Enables or disables the Azalia internal HDMI codec.
Control detection of the Azalia device. Disable= Azalia will be unconditionally disabled Enabled= Azalia will be unconditionally enabled Auto=Azalia will be ena­bled if present, disabled otherwise.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
System Agent (SA) Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
System Agent Bridge Name System Agent RC Version VT-d Capability

Graphics Confi guration

NB PCIe Confi guration

Memory Confi guration
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
NB PCIe Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
NB PCIe Confi guration PEG0
Enable PEG
IvyBridge
1.1.0.0 Supported
Not Present
[Auto]
Confi g Graphics settings.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
To enable or disable the PEG.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enabled PEG
To enable or disable the PEG
41
.
www.dfi .comChapter 4 BIOS Setup
Page 42
Chapter 4
Graphics Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
Graphics Confi guration IGFX VBIOS Version IGfx Frequency
Primary Display
Internal Graphics DVMT Total Gfx Mem
LCD Control
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
2126 350 MHz
[Auto]
[Auto] [256M]
Select which of IGFX/ PEG/PCI Graphics device should be primary display or select SG for Switch­able Gfx.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Primary Display Auto When the system boots, it will auto detects the display device.
IGFX When the system boots, it will first initialize the onboard VGA.
PEG When the system boots, it will first initialize the PCI Express x16 graphics card.
Internal Graphics
LCD Control
LCD Control
Primary IGFX Boot Display
Secondary IGFX Boot Display LCD Panel Type
Secondary IGFX Boot Display
Select secondary display device
LCD Panel Type
Select LCD panel used by Internal Graphics Device by selecting the appropri­ate setup item.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
Select the Video Device
[CRT]
[Disabled] [VBIOS Default]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be sup­ported only on primary display.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
.
Keep IGD enabled based on setup options.
DVMT Total Gfx Mem
Select DVMT5.0 total graphic memory size used by the internal graphics
.
device
42
www.dfi .comChapter 4 BIOS Setup
Page 43
Chapter 4
Memory Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
Memory Information Memory RC Version
Memory Frequency Total Memory DIMM#0 DIMM#2 CAS Latency (tCL) Minimum delay time CAS to RAS (tRCDmin) Row Precharge (tRPmin) Active to Precharge (tRASmin) XMP Profi le 1 XMP Profi le 2
DDR Select
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
NB PCIe Bifurcation Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
NB PCIe Bifurcation Confi guration
PEG Bifurcation
PEG Birfurcation x8, x4, x4
Reserved x8, x8 x16
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
1.0.0.1 1333 Mhz 2048 MB (DDR3) Not Present 2048 MB (DDR3) 9
9 9 24 Not supported Not suppoted
[DDR3]
[x16]
DDR3 or DDR3L selec­tion.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
PEG bifurcation confi gu- ration.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Boot
Main
Boot Confi guration
Setup Prompt Timeout
Bootup NumLock State Quiet Boot
Fast Boot
CSM16 Module Version
Boot Option Priorities
Boot Option #1 Boot Option #2 Boot Option #3 Boot Option #4 Boot Option #5
CD/ DVD ROM Driver BBS Priorities Hard Driver BBS Priorities Floppy Driver BBS Priorities
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Boot
Security
1
[On] [Disabled]
[Disabled]
07.68
[P2: ATAPI iHOS10...] [P0 WDC WD2500BEVS] [MITSUBI USB FDD00] [UEFI: Sony Storage] [UEFI: MITSUMI USB]
Save & ExitChipset
Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefi nite waiting.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Setup Prompt Timeout
Selects the number of seconds to wait for the setup activation key. 65535(0xFFFF) denotes indefinite waiting.
Bootup NumLock State
This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys.
Quiet Boot
Enables or disables the quiet boot function.
Fast Boot
Enables or disables boot with initialization of a minimal set of devices re quired to launch active boot option. Has no effect for BBS boot options.
43
www.dfi .comChapter 4 BIOS Setup
Page 44
Chapter 4
Security
Main
Password Description If ONLY the Administrator’s password is set,
then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20
Administrator Password
User Password
HDD Security Confi guration
P0:WDC WD2500BE P4:GLS85LS1004P
Administrator Password
Sets the administrator password.
User Password
Sets the user password.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Boot Security
Save & Exit
Save & ExitChipset
Set Administrator Password.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
Main
Save Changes and Reset
Discard Changes and Reset
Save Options
Save Changes Discard Changes
Restore Defaults Save as User Defaults Restore User Defaults
Boot Override
P2: ATAPI iHOS104 P0: WDC WD2500BEVS-00UST0 UEFI: Sony Storage Media 0100 MITSUMI USB FDD 070M3.01 UEFI: MITSUMI USB FDD 070M3.01
Launch EFI Shell from fi lesystem device
Save Changes and Reset
To save the changes, select this field and then press <Enter>. A dialog box will ap­pear. Select Yes to reset the system after saving all changes made
Discard Changes and Reset
To discard the changes, select this field and then press <Enter>. A dialog box will appear. Select Yes to reset the system setup without saving any changes.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Chipset
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Boot Security Save & Exit
Reset the system after saving the changes.
 Select Screen  Select Item
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults ESC: Exit
.
Save Changes
Save the changes done so far to any of the set up options.
Discard Changes
Discard changes done so far to any of the set up options.
Restore Defaults
To restore and load the optimized default values, select this field and then press <Enter>. A dialog box will appear. Select Yes to restore the default values of all the setup options.
44
www.dfi .comChapter 4 BIOS Setup
Page 45
Chapter 4
Save as User Defaults
To save changes done so far as user default, select this field and then press <Enter>. A dialog box will appear. Select Yes to save values as user default.
Restore User Defaults
To restore user default to all the setup options, select this field and then press <Enter>. A dialog box will appear. Select Yes to restore user default.
Clear Administrator or User Password
Note:
Using the “Restore Default” function in the “Save & Exit” screen will not clear the old password. Make sure to follow the steps below.
If you forgot the administrator or user password, follow the steps below to clear the old password.
1. Power-off the system or turn off the power supply.
2. Set the Clear CMOS jumper to “Clear CMOS” mode. Wait for a few seconds and set the jumper back to its default setting.
3. Power-on the system. When the “CMOS Checksum Error” message appears, press
<Delete> to enter the BIOS.
4. Select “Save & Exit”. In the “Save & Exit” screen, select “Save Change & Reset” and then press Enter.
Updating the BIOS
To update the BIOS, you will need the new BIOS file and a flash utility, AFUDOS.EXE. Please contact technical support or your sales representative for the files.
To execute the utility, type: A:> AFUDOS BIOS_File_Name /b /p /n then press <Enter>.
C:\AFU\AFUDOS>afudos fi lename /B /P /N
+--------------------------------------------------------------------------------------------------------+
| |
+--------------------------------------------------------------------------------------------------------+
Reading fi le ..............................
Erasing fl ash .............................
Writing fl ash .............................
Verifying fl ash ..........................
Erasing BootBlock ....................
Writing BootBlock ....................
Verifying BootBlock .................
C:\AFU\AFUDOS>
AMI Firmware Update Utility(APTIO) v2.25
Copyright (C)2008 American Megatrends Inc. All Rights Reserved.
done done done done done done done
After finishing BIOS update, please turn off the AC power. Wait about 10 seconds and then turn on the AC power again.
| |
45
www.dfi .comChapter 4 BIOS Setup
Page 46
Chapter 4
Notice: BIOS SPI ROM
1. The Intel® Management Engine has already been integrated into this system board. Due to the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and used on another system board of the same model.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory and cannot be used to replace one which has been utilized on other system boards.
®
3. If you do not follow the methods above, the Intel updated and will cease to be effective.
Note:
a. You can take advantage of flash tools to update the default configuration of the BIOS (SPI ROM) to the latest version anytime. b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the technical person's instructions to confirm that the MAC address should be burned or not.
Management Engine will not be
46
www.dfi .comChapter 4 BIOS Setup
Page 47
Chapter 5 - Supported Software
The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board.
Insert the CD into a CD-ROM drive. The autorun screen (Mainboard Utility CD) will appear. If after inserting the CD, “Autorun” did not automatically start (which is, the Mainboard Utility CD screen did not appear), please go directly to the root directory of the CD and double-click “Setup”.
Chapter 5
Intel Chipset Device Software
The Intel Chipset Device Software is used for updating Windows chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Device Software” on the main menu.
1. Setup is ready to install the utility. Click Next.
®
INF files so that the Intel
2. Read the license agreement then click Yes.
47
www.dfi .comChapter 5 Supported Software
Page 48
Chapter 5
3. Go through the readme docu­ment for more installation tips then click Next.
4. After all setup operations are
done, click Next.
Intel HD Graphics Drivers (for Windows 7)
To install the driver, click “Intel HD Graphics Drivers” on the main menu.
1. Setup is now ready to install the graphics driver. Click Next.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is enabled. With this enabled, after installing the graphics driver and the system rebooted, the screen will turn blank for 1 to 2 minutes (while WinSAT is running) before the Windows Vista desktop appears. The “blank screen” period is the time Windows is testing the graphics perfor­mance.
We recommend that you skip this process by disabling this function then click Next.
5. Click “Yes, I want to restart this computer now” then click Finish.
Restarting the system will allow the new software installation to take effect.
48
www.dfi .comChapter 5 Supported Software
Page 49
Chapter 5
2. Read the license agreement then click Yes.
3. Go through the readme docu­ment for system requirements and installation tips then click Next.
5. Click “Yes, I want to restart this computer now” then click Finish.
Restarting the system will allow the new software installation to take effect.
4. Setup is now installing the driver. Click Next to continue
.
49
www.dfi .comChapter 5 Supported Software
Page 50
Chapter 5
Intel HD Graphics Drivers (for Windows XP)
Note:
Before installing Intel HD Graphics Drivers, make sure you have installed Microsoft .NET Framework 3.5 SP1.
To install the driver, click “Intel HD Graphics Drivers” on the main menu.
1. Setup is ready to install the graph­ics driver. Click Next
2. Read the license agreement then click Yes.
.
3. Go through the readme document for more installation tips then click Next.
4. Setup is currently installing the driver. After installation has com­pleted, click Next.
5. Click “Yes, I want to restart this computer now.” then click Finish.
Restarting the system will allow the new software installlation to take effect.
50
www.dfi .comChapter 5 Supported Software
Page 51
Chapter 5
Intel Management Engine Drivers
To install the driver, click “Intel Management Engine Drivers” on the main menu.
1. Setup is ready to install the driver. Click Next.
2. Read the license agreement then click Yes.
3. Setup is currently installing the driver. After installation has com­pleted, click Next.
4. After completing installation, click Finish.
51
www.dfi .comChapter 5 Supported Software
Page 52
Chapter 5
Intel USB 3.0 Drivers (for Windows 7 only)
To install the driver, click “Intel USB 3.0 Driver” on the main menu.
1. Setup is ready to install the driver. Click Next.
2. Read the license agreement then click Yes.
3. Go through the readme docu­ment for more installation tips then click Next.
4. Setup is currently installing the driver. After installation has com­pleted, click Next.
5. After completing installation, click Finish.
52
www.dfi .comChapter 5 Supported Software
Page 53
Chapter 5
Audio Drivers (for COM331-B Carrier Board)
To install the driver, click “Audio Drivers (for COM331-B Carrier Board” on the main menu.
1. Setup is now ready to install the audio driver. Click Next.
2. Follow the remainder of the steps on the screen; clicking “Next” each time you finish a step.
3. Click “Yes, I want to restart my computer now” then click Finish.
Restarting the system will allow the new software installation to take effect.
Intel LAN Drivers
To install the driver, click “Intel LAN Drivers” on the main menu.
1. Setup is ready to install the driver. Click Install Drivers and Sofeware.
2. Setup is now ready to install the LAN driver. Click Next.
3. Click “I accept the terms in the li­cense agreement” then click Next
53
.
www.dfi .comChapter 5 Supported Software
Page 54
Chapter 5
4. Select the program featuers you want installed then click Next.
5. Click Install to begin the instal­lation.
DFI Utility
DFI Utility provides information about the board, HW Health, Watchdog, DIO, and Backlight. To access the utility, click “DFI Utility” on the main menu.
Note:
If you are using Windows 7, you need to access the operating system as an adminis­trator to be able to install the utility.
1. Setup is ready to install the DFI Utility drifer. Click Next.
2. Click “I accept the terms in the license agreement” and then click
.
Next
6. After completing installation, click Finish.
54
www.dfi .comChapter 5 Supported Software
Page 55
Chapter 5
3. Enter “User Name” and “Organi­zation” information and then click
.
Next
4. Click Install to begin the installation.
The DFI Utility icon will appear on the desktop. Double-click the icon to open the utility.
5. After completing installation, click Finish.
55
www.dfi .comChapter 5 Supported Software
Page 56
Chapter 5
Intel Rapid Storage Technology
The Intel Rapid Storage Technology is a utility that allows you to monitor the current status of the SATA drives. It enables enhanced performance and power management for the storage subsystem.
To install the driver, click “Intel Rapid Storage Technology” on the main menu.
1. Setup is now ready to install
2. Read the warning then click
Note:
Windows Vista is not supported.
the utility. Click Next.
Yes.
3. Read the license agreement then click Yes.
4. Go through the readme document for system requirements and instal­lation tips then click Next.
5. Setup is now installing the utility. Click Next to continue.
56
www.dfi .comChapter 5 Supported Software
Page 57
Chapter 5
6. Click “Yes, I want to restart my computer now” then click Finish.
Restarting the system will allow the new software installation to take effect.
7. Run the Intel Matrix Storage
Console utility to view the hard drives’ configuration.
Intel Turbo Boost Monitor (for Windows 7 only)
To install the driver, click “Intel Turbo Boost Monitor” on the main menu.
1. The setup program is configuring the new software installation
2. Click Next.
.
3. Read the license agreement and then click “I accept the terms in the license agreement”. Click Next.
57
www.dfi .comChapter 5 Supported Software
Page 58
Chapter 5
Infineon TPM Driver and Tool (optional)
To install the driver, click “Infineon TPM driver and tool (option)” on the main menu.
1. Read the message and click OK.
2. The setup program is preparing to install the driver.
4. Enter the necessary information and then click Next.
5. Select a setup type and then click Next.
3. Click “I accept the terms in the license agreement” and then click “Next”.
58
www.dfi .comChapter 5 Supported Software
Page 59
Chapter 5
4. Click Install.
5. The setup program is currently installing the software.
Adobe Acrobat Reader 9.3
To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.
1. Click Next to install or click Change Destination Folder to select another folder.
2. Click Install to begin installation.
6. Click Finish.
3. Click Finish to exit installation.
59
www.dfi .comChapter 5 Supported Software
Page 60
Appendix A
Appendix A - NLITE and AHCI Installation Guide
nLite
nLite is an application program that allows you to customize your XP installation disc by integrating the RAID/AHCI drivers into the disc. By using nLite, the F6 function key usually required during installation is no longer needed.
Note:
The installation steps below are based on nLite version 1.4.9. Installation procedures may slightly vary if you’re using another version of the program.
1. Download the program from nLite’s offical website.
http://www.nliteos.com/download.html
2. Install nLite.
4. Insert the XP installation disc into an optical drive.
5. Launch nLite. The Welcome screen will appear. Click Next.
Important:
Due to it’s coding with Visual.Net, you may need to first install .NET Framework prior to installing nLite.
3. Download relevant RAID/AHCI driver files from Intel’s website. The drivers you choose will depend on the operating system and chipset used by your computer.
The downloaded driver files should include iaahci.cat, iaAHCI.inf, iastor.cat, iaStor. inf, IaStor.sys, license.txt and TXTSETUP.OEM.
6. Click Next to temporarily save the Windows installa­tion files to the designated default folder.
If you want to save them in another folder, click Browse, select the folder and then click Next.
60
www.dfi .comAppendix A NLITE and AHCI Installation Guide
Page 61
Appendix A
7. Click Next.
8. In the Task Selection dialog box, click Drivers and Bootable ISO. Click Next.
9. Click Insert and then select Multiple driver folder to select the drivers you will integrate. Click Next.
10. Select only the drivers ap-
propriate for the Windows version that you are using and then click OK.
Integrating 64-bit drivers into 32-bit Windows or vice versa will cause file load errors and failed installation.
61
www.dfi .comAppendix A NLITE and AHCI Installation Guide
Page 62
Appendix A
11. If you are uncertain of the southbridge chip used on your motherboard, select all RAID/AHCI controllers and then click OK
12. Click Next.
.
13. The program is currently integrating the drivers and applying changes to the installation.
14. When the program is fin­ished applying the changes, click Next.
62
www.dfi .comAppendix A NLITE and AHCI Installation Guide
Page 63
Appendix A
15. To create an image, select the Create Image mode under the General section and then click Next.
16. Or you can choose to burn it directly to a disc by selecting the Direct Burn mode under the General section.
Select the optical device and all other necessary settings and then click Next
.
17. You have finished customizing the Windows XP installation disc. Click Finish.
Enter the BIOS utility to configure the SATA controller to RAID/AHCI. You can now install Windows XP.
63
www.dfi .comAppendix A NLITE and AHCI Installation Guide
Page 64
Appendix A
AHCI
The installation steps below will guide you in configuring your SATA drive to AHCI mode.
1. Enter the BIOS utility and configure the SATA controller to IDE mode.
2. Install Windows XP but do not press F6.
3. Download relevant RAID/AHCI driver files supported by the motherboard chip­set from Intel’s website.
Transfer the downloaded driver files to C:\AHCI.
4. Open Device Manager and right click on one of the Intel Serial ATA Storage Con­trollers, then select Update Driver.
If the controller you selected did not work, try selecting another one.
5. In the Hardware Update Wizard dialog box, select “No, not this time” then click Next.
6. Select “Install from a list or specific location (Advanced)” and then click Next.
7. Select “Don’t search. I will choose
the driver to install” and then click
.
Next
64
www.dfi .comAppendix A NLITE and AHCI Installation Guide
Page 65
Appendix A
8. Click “Have Disk”.
9. Select C:\AHCI\iaAHCI.inf and then click Open.
11. A warning message appeared because the selected SATA controller did not match your hardware device.
Ignore the warning and click Yes to proceed.
12. Click Finish.
13. The system’s settings have
been changed. Windows XP requires that you restart the computer. Click Yes.
10. Select the appropriate AHCI Controller of your hardware device and then click Next.
14. Enter the BIOS utility and modify the SATA controller from IDE to AHCI. By doing so, Windows will work normally with the SATA controller that is in AHCI mode.
65
www.dfi .comAppendix A NLITE and AHCI Installation Guide
Page 66
Appendix B - Watchdog Sample Code
Appendix B
#include <stdio.h> //-------------------------------------------------------------­#defi ne EC_EnablePort 0x66 #defi ne EC_DataPort 0x62 //-------------------------------------------------------------­void WriteEC(char,int); void SetWDTime(int,int); int GetWDTime(void); //-------------------------------------------------------------­main() { unsigned int countdown; unsigned int input,count_h,count_l;
printf("Input WD Time: "); scanf("%d",&input); printf("\n"); count_h=input>>8; count_l=input&0x00FF; SetWDTime(count_h,count_l);
while(1) { countdown = GetWDTime(); delay(100); printf("\rTime Remaining: %d ",countdown); } } //-------------------------------------------------------------­void SetWDTime(int count_H,int count_L) { //Set Count WriteEC(0xB7,count_H); //High Byte WriteEC(0xB8,count_L); //Low Byte //Enable Watch Dog Timer WriteEC(0xB4,0x02); } //--------------------------------------------------------------
int GetWDTime(void) { int sum,data_h,data_l; //Select EC Read Type outportb(EC_EnablePort,0x80); delay(5); //Get Remaining Count High Byte outportb(EC_DataPort,0xF6); delay(5); data_h=inportb(EC_DataPort); delay(5); //Select EC Read Type outportb(EC_EnablePort,0x80); delay(5); //Get Remaining Count Low Byte outportb(EC_DataPort,0xF7); delay(5); data_l=inportb(EC_DataPort); delay(5);
data_h<<=8; data_h&=0xFF00; sum=data_h|data_l; return sum; } //-------------------------------------------------------------­void WriteEC(char EC_Addr, int data) { //Select EC Write Type outportb(EC_EnablePort,0x81); delay(5); outportb(EC_DataPort,EC_Addr); delay(5); outportb(EC_DataPort,data); delay(5); } //--------------------------------------------------------------
66
www.dfi .comAppendix B Watchdog Sample Code
Page 67
Appendix C
Appendix C - System Error Message
When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in the information box at the bottom. Enter Setup to correct the error.
Error Messages
One or more of the following messages may be displayed if the BIOS detects an error during the POST. This list indicates the error messages for all Awards BIOSes:
CMOS BATTERY HAS FAILED
The CMOS battery is no longer functional. It should be replaced.
Important
Danger of explosion if battery incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries accord-
ing to the battery manufacturer’s instructions.
CMOS CHECKSUM ERROR Checksum of CMOS is incorrect. This can indicate that CMOS has become corrupt. This error
may have been caused by a weak battery. Check the battery and replace if necessary.
DISPLAY SWITCH IS SET INCORRECTLY
The display switch on the motherboard can be set to either monochrome or color. This indi­cates the switch is set to a different setting than indicated in Setup. Determine which setting is correct, either turn off the system and change the jumper or enter Setup and change the VIDEO selection.
67
www.dfi .comAppendix C System Error Message
Page 68
Appendix D - Troubleshooting
Appendix D
The picture seems to be constantly moving.
Troubleshooting Checklist
This chapter of the manual is designed to help you with problems that you may encounter with your personal computer. To efficiently troubleshoot your system, treat each problem indi­vidually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple causes.
Some of the most common things to check when you encounter problems while using your system are listed below.
1. The power switch of each peripheral device is turned on.
2. All cables and power cords are tightly connected.
3. The electrical outlet to which your peripheral devices are connected is working. Test the outlet by plugging in a lamp or other electrical device.
4. The monitor is turned on.
5. The display’s brightness and contrast controls are adjusted properly.
6. All add-in boards in the expansion slots are seated securely.
7. Any add-in board you have installed is designed for your system and is set up correctly.
Monitor/Display
If the display screen remains dark after the system is turned on:
1. Make sure that the monitor’s power switch is on.
2. Check that one end of the monitor’s power cord is properly attached to the monitor and the other end is plugged into a working AC outlet. If necessary, try another outlet.
1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.
2. Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display.
3. Make sure your video card’s output frequencies are supported by this monitor.
The screen seems to be constantly wavering.
1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off. Fluorescent lights adjacent to the monitor may also cause screen wavering.
Power Supply
When the computer is turned on, nothing happens.
1. Check that one end of the AC power cord is plugged into a live outlet and the other end properly plugged into the back of the system.
2. Make sure that the voltage selection switch on the back panel is set for the correct type of voltage you are using.
3. The power cord may have a “short” or “open”. Inspect the cord and install a new one if necessary.
3. Check that the video input cable is properly attached to the monitor and the system’s display adapter.
4. Adjust the brightness of the display by turning the monitor’s brightness control knob
.
68
www.dfi .comAppendix D Troubleshooting
Page 69
Appendix D
Hard Drive
Hard disk failure.
1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS.
2. If the system is configured with two hard drives, make sure the bootable (first) hard drive is configured as Master and the second hard drive is configured as Slave. The master hard drive must have an active/bootable partition.
Excessively long formatting period.
If your hard drive takes an excessively long period of time to format, it is likely a cable con­nection problem. However, if your hard drive has a large capacity, it will take a longer time to format.
Serial Port
The serial device (modem, printer) doesn’t output anything or is outputting garbled
characters.
1. Make sure that the serial device’s power is turned on and that the device is on-line.
2. Verify that the device is plugged into the correct serial port on the rear of the computer.
3. Verify that the attached serial device works by attaching it to a serial port that is work­ing and configured correctly. If the serial device does not work, either the cable or the serial device has a problem. If the serial device works, the problem may be due to the onboard I/O or the address setting.
4. Make sure the COM settings and I/O address are configured correctly.
System Board
1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is loose, power off the system, re-install the card and power up the system.
2. Check the jumper settings to ensure that the jumpers are properly set.
3. Verify that all memory modules are seated securely into the memory sockets.
4. Make sure the memory modules are in the correct locations.
5. If the board fails to function, place the board on a flat surface and seat all socketed compo­nents. Gently press each component into the socket.
6. If you made changes to the BIOS settings, re-enter setup and load the BIOS defaults.
Keyboard
Nothing happens when a key on the keyboard was pressed.
1. Make sure the keyboard is properly connected.
2. Make sure there are no objects resting on the keyboard and that no keys are pressed dur­ing the booting process.
69
www.dfi .comAppendix D Troubleshooting
Loading...