Page 1
www.d.comChapter 1 Introduction
1
BT9A3 Series
COM Express Mini
User’s Manual
A31100409
Coming Soon
Page 2
www.dfi .comChapter 1 Introduction
2
Copyright
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2014. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
COM Express Specification Reference
PICMG® COM Express ModuleTM Base Specification.
http://www.picmg.org/
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Page 3
www.dfi .comChapter 1 Introduction
3
Table of Contents
Copyright .............................................................................................................2
Trademarks ........................................................................................................2
FCC and DOC Statement on Class B ..................................................... 2
About this Manual ..........................................................................................4
Warranty ............................................................................................................4
Static Electricity Precautions ......................................................................4
Safety Measures ..............................................................................................4
About the Package .........................................................................................5
Chapter 1 - Introduction .............................................................................6
Specifications ................................................................................................6
Features ..........................................................................................................7
Chapter 2 - Concept .......................................................................8
COM Express Module Standards .............................................................. 8
Specification Comparison Table ...............................................................9
Chapter 3 - Hardware Installation .............................................. 10
Board Layout ...............................................................................................10
Block Diagram ............................................................................................. 10
System Memory .......................................................................................... 11
Connectors ...................................................................................................12
CPU Fan Connector .....................................................................................12
COM Express Connector .............................................................................. 12
COM Express Connector Signal Discription ................................................... 14
Page 4
www.dfi .comChapter 1 Introduction
4
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Page 5
www.dfi .comChapter 1 Introduction
5
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• One BT9A3 board
• One QR (Quick Reference)
• One DVD
Optional Items
• COM100-B carrier board kit
• Heat sink: TBD
• Heat sink with fan: TBD
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
Page 6
www.dfi .comChapter 1 Introduction
6
Watchdog
Timer
• Watchdog timeout programmable via software from 1 to 255 seconds
Damage Free
Intelligence
• Monitors CPU/system temperature and overheat alarm
• Monitors Vcore/Vgfx/VDDR/3V3 voltages and failure alarm
• Monitors CPU/system fan speed and failure alarm
• Watchdog timer function
BIOS
• 16Mbit SPI BIOS
OS Support
• TBD
Power
Consumption
• TBD
Temperature
• Operating
- Atom: 0
o
C to 60oC, -20oC to 70oC, -40oC to 85oC
- Celeron: 0
o
C to 60oC
• Storage: -40
o
C to 85oC
Humidity
• 5% to 90%
Power Input
• 4.75V~20V, 5VSB, VCC_RTC (ATX mode)
• 4.75V~20V, VCC_RTC (AT mode)
PCB
• Dimensions
- COM Express
®
Mini
- 84mm (3.30") x 55mm (2.16")
• Compliance
- PICMG COM Express
®
R2.1, Type 10
Chapter 1 - Introduction
Specifications
Processor
• Intel® AtomTM/Intel® Celeron® processors
- E45:
Intel® AtomTM E3845, Quad Core, 2M Cache, 1.91GHz, 10W
- E27: Intel
®
AtomTM E3827, Dual Core, 1M Cache, 1.75GHz, 8W
- E26: Intel
®
AtomTM E3826, Dual Core, 1M Cache, 1.46GHz, 7W
- E25: Intel
®
AtomTM E3825, Dual Core, 1M Cache, 1.33GHz, 6W
- E15: Intel
®
AtomTM E3815, Single Core, 0.5M Cache, 1.46GHz, 5W
- J00:
Intel® Celeron® J1900, Quad Core, 2M Cache, up to 2.42GHz, 10W
- N30: Intel
®
Celeron® N2930, Quad Core, 2M Cache, up to 2.16GHz, 7.5W
• BGA 1170 packaging technology
• 22nm process technology
System Memory
• 2GB/4GB DDR3L ECC onboard
• Supports DDR3L 1333MHz (-E45/-E27/-J00/-N30)
Supports DDR3L 1066MHz (-E26/-E25/-E15)
• Supports single channel memory interface
Storage
• Supports 4GB, 8GB and 16GB eMMC onboard (optional)
Graphics
• Intel® HD Graphics
• Supports LVDS and DDI interfaces
• LVDS: NXP PTN3460, 24-bit, dual channel, resolution up to 1920x1200 @60Hz
• Digital Display Interface: HDMI, DVI and DP
• HDMI, DVI: resolution up to 2560x1600 @24Hz
• DP: resolution up to 2560x1600 @60Hz
• Supports hardware acceleration for DirectX 11, OCL 1.2, OGL 3.2, H.264,
MPEG2, MVC, VC-1, WMV9 and VP8
Audio
• Supports High Defi nition Audio interface
LAN
• Intel® I210 Gigabit Ethernet Controller
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Serial ATA
• Supports 2 Serial ATA interfaces
• SATA 2.0 with data transfer rate up to 3Gb/s
• Integrated Advanced Host Controller Interface (AHCI) controller
Expansion
Interfaces
• Supports 1 USB 3.0 port
• Supports 8 USB 2.0 ports
- 4 integrated USB 2.0 ports
- 1 USB HSIC for 4 USB 2.0 ports
• Supports 3 PCIe x1 (default); or 1 PCIe x4 (PCIe port 3 share with onboard
LAN by default)
• Supports LPC interface
• Supports I
2
C interface
• Supports SMBus interface
• Suppotrs 2 serial interfaces (TX/RX)
• Supports 8-bit Digital I/O
Chapter 1
Page 7
www.dfi .comChapter 1 Introduction
7
Features
• Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
• DDR3L
DDR3L delivers increased system bandwidth and improved performance to provide its higher
bandwidth and its increase in performance at a lower power than DDR2 and DDR3.
• Graphics
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications. Supports LVDS and DDI (HDMI,
DVI and DisplayPort) for up to 2 independent displays.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 3Gb/s (SATA 2.0), it improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s.
• Gigabit LAN
The Intel® WGI210AT Gigabit LAN controller supports up to 1Gbps data transmission.
• USB
The system board supports the new USB 3.0. It is capable of running at a maximum transmission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously
accessible external Plug and Play peripherals.
Chapter 1
Page 8
www.dfi .comChapter 2 Concept
8
Chapter 2
Chapter 2 - Concept
COM Express Module Standards
The figure below shows the dimensions of the different types of COM Express modules.
BT9A3 Series is a COM Express Mini. The dimension is 84mm x 55mm.
106.00
91.00
70.00
51.00
4.00
18.00
6.00
0.00
16.50
4.00
0.00
Extended
BasicCompact
Mini
74.20
80.00
91.00
121.00
151.00
Common for all Form Factors
Extended only
Basic only
Compact only
Compact and Basic only
Mini only
Page 9
www.dfi .comChapter 2 Concept
9
Chapter 2
Specification Comparison Table
The table below shows the COM Express standard specifications and the corresponding specifications supported on the BT9A3 Series module.
Module Pin-out - Required and Optional Features C-D Connector. PICMG® COM.0Revision 2.1
Note:
• 5 Indicates 12V-tolerant features on former VCC_12V signals.
• 6 Cells in the connected columns spanning rows provide a rough approximation of
features sharing connector pins.
Connector Feature
COM Express Module Base
Specification Type 10
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI BT9A3 Sries
Type 10
A-B
A-B PCI Express Lanes 0 - 5 1 / 4
3
A-B LVDS Channel A 0 / 1
1
A-B LVDS Channel B NA
NA
A-B eDP on LVDS CH A pins 0 / 1
1
A-B VGA Port NA
NA
A-B TV-Out NA
NA
A-B DDI 0 0/1
1
A-B
5
Serial Ports 1 - 2 0 / 2
2
A-B CAN interface on SER1 0 / 1
0
A-B SATA / SAS Ports 1 / 2
2
A-B AC’97 / HDA Digital Interface 0 / 1
1
A-B USB 2.0 Ports 4 / 8
8
A-B USB Client 0 / 1
0
A-B USB 3.0 Ports 0/2
1
A-B LAN Port 0 1 / 1
1
A-B Express Card Support 0/2
2
A-B LPC Bus 1 / 1
1
A-B SPI 1 / 2
1
A-B
SDIO (muxed on GPIO) 0 / 1
0
General Purpose I/O 8 / 8
8
A-B SMBus 1 / 1
1
A-B I2C 1 / 1
1
A-B Watchdog Timer 0 / 1
1
A-B Speaker Out 1 / 1
1
A-B External BIOS ROM Support 0 / 2
1
A-B Reset Functions 1 / 1
1
A-B
6
System I/O
System Management
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI BT9A3 Series
Type 10
A-B
A-B Thermal Protection 0 / 1
1
A-B Battery Low Alarm 0 / 1
1
A-B Suspend/Wake Signals 0 / 3
3
A-B Power Button Support 1 / 1
1
A-B Power Good 1 / 1
1
A-B VCC_5V_SBY Contacts 4 / 4
4
A-B
5
Sleep Input 0 / 1
1
A-B
5
Lid Input 0 / 1
1
A-B
5
Fan Control Signals 0 / 2
2
A-B Trusted Platform Modules 0 / 1
0
A-B
A-B VCC_12V Contacts 12 / 12
12
Power Management
Power
Connector Feature
COM Express Module Base
Specification Type 10
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI BT9A3 Series
Type 10
C-D
PCI Express Lanes 16 - 31 NA
N
A
PCI Express Graphics (PEG) NA
N
A
Muxed SDVO Channels 1 - 2 NA
N
A
PCI Express Lanes 6 - 15 NA
N
A
PCI Bus - 32 Bit NA
N
A
PATA Port NA
N
A
LAN Ports 1 - 2 NA
N
A
DDIs 1 - 3 NA
N
A
USB 3.0 Ports NA
N
A
C-D
C-D VCC_12V Contacts NA
N
A
System I/O
Power
C-D
6
C-D
6
Page 10
www.dfi .comChapter 3 Hardware Installation
10
Chapter 3
Chapter 3 - Hardware Installation
Board Layout
Top View
Bottom View
Block Diagram
EEPROM
USB 2.0 4x
SATA 2.0 2x
A / B
USB 2.0 4x
SATA 2.0 2x
SM Bus
Atom E3800 Series
/Celeron
eMMC
(Optional)
MMC Bus
Intel® GLAN
I210
PCIe x1 (Opt.)
GLAN
SPI
Flash
C / D
eDPLVDS
DDR3L 1GB
ECC 8x onboard
DDR3
1333MHz
Single Channel
PTN3460
PCIe x1
DDI
DDI
PCIe x1 (Opt.)
USB4604I
USB 2.0 4x
USB HSIC
HD Audio
LPC Bus
HD Audio
LPC Bus
Embedded
Controller
IT8528
8-bit DIO
WDT
I
2
C Bus
Serial Port1, 2 Tx/Rx
System Fan
PWM/TACH
SLP/LID
S/
TCA6408A
T
USB 3.0 1x
USB 3.0 1x
PCIe x1
PCIe x1
PCIe x1
PCIe x1
PCIe x1
PCIe x1
Switch
Fla
sh
E3800 Series
Intel Atom
DDR3L
DDR3L
DDR3L
DDR3L
DDR3L
SPI Flash BIOS
CPU fan
1
NXP
PTN3460
Intel
WGI210AT
DDR3L
DDR3L
DDR3L
DDR3L
B110
B1
A110
A1
SMSC
USB4604
COM Express connector
Page 11
www.dfi .comChapter 3 Hardware Installation
11
Chapter 3
System Memory
The system board is equipped with eight DDR3L memory chips onboard.
• 2GB/4GB DDR3L ECC onboard
• Supports DDR3L 1333MHz (-E45/-E27/-J00/-N30)
Supports DDR3L 1066MHz (-E26/-E25/-E15)
• Supports single channel memory interface
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
System Memory
DDR3L
Top View
DDR3L
Bottom View
Page 12
www.dfi .comChapter 3 Hardware Installation
12
Chapter 3
Connectors
CPU Fan Connector
Connect the CPU fan’s cable connector to the CPU fan connector on the board. The cooling fan
will provide adequate airflow throughout the chassis to prevent overheating the CPU and board
components.
BIOS Setting
“Module Board H/W Monitor” submenu in the Advanced menu of the BIOS will display the current speed of the cooling fan. Refer to chapter 3 of the manual for more information
.
COM Express Connector
The COM Express connector is used to interface the BT9A3 Series COM Express board to a
carrier board. Connect the COM Express connector (lcoated on the solder side of the board) to
the COM Express connector on the carrier board.
Refer to the following pages for the pin functions of the connector.
3
1
Sense
+12V
Ground
COM Express Connector
Page 13
www.dfi .comChapter 3 Hardware Installation
13
Chapter 3
COM Express Connector
A1 GND (FIXED) B1 GND (FIXED)
A2 GBE0_MDI3- B2 GBE0_ACT#
A3 GBE0_MDI3+ B3 LPC_FRAME#
A4 GBE0_LINK100# B4 LPC_AD0
A5 GBE0_LINK1000# B5 LPC_AD1
A6 GBE0_MDI2- B6 LPC_AD2
A7 GBE0_MDI2+ B7 LPC_AD3
A8 GBE0_LINK# B8 LPC_DRQ0#
A9 GBE0_MDI1- B9 LPC_DRQ1#
A10 GBE0_MDI1+ B10 LPC_CLK
A11 GND (FIXED) B11 GND (FIXED)
A12 GBE0_MDI0- B12 PWRBTN#
A13 GBE0_MDI0+ B13 SMB_CK
A14 GBE0_CTREF B14 SMB_DAT
A15 SUS_S3# B15 SMB_ALERT#
A16 SATA0_TX+ B16 SATA1_TX+
A17 SATA0_TX- B17 SATA1_TXA18 SUS_S4# B18 SUS_STAT#
A19 SATA0_RX+ B19 SATA1_RX+
A20 SATA0_RX- B20 SATA1_RXA21 GND (FIXED) B21 GND (FIXED)
A22 USB_SSRX0- B22 USB_SSTX0A23 USB_SSRX0+ B23 USB_SSTX0+
A24 SUS_S5# B24 PWR_OK
A25 USB_SSRX1- B25 USB-SSTX1A26 USB_SSRX1+ B26 USB-SSTX1+
A27 BATLOW# B27 WDT
A28 (S)ATA_ACT# B28 AC/HDA _SDIN2
A29 AC/HDA_SYNC B29 AC/HDA _SDIN1
A30 AC/HDA _RST# B30 AC/HDA _SDIN0
Row A Row B
Row A Row B
A31 GND (FIXED) B31 GND (FIXED)
A32 AC/HDA _BITCLK B32 SPKR
A33 AC/HDA _SDOUT B33 I2C_CK
A34 BIOS_DIS0# B34 I2C_DAT
A35 THRMTRIP# B35 THRM#
A36 USB6- B36 USB7A37 USB6+ B37 USB7+
A38 USB_6_7_OC# B38 USB_4_5_OC#
A39 USB4- B39 USB5A40 USB4+ B40 USB5+
A41 GND (FIXED) B41 GND (FIXED)
A42 USB2- B42 USB3A43 USB2+ B43 USB3+
A44 USB_2_3_OC# B44 USB_0_1_OC#
A45 USB0- B45 USB1A46 USB0+ B46 USB1+
A47 VCC_RTC B47 EXCD1_PERST#
A48 EXCD0_PERST# B48 EXCD1_CPPE#
A49 EXCD0_CPPE# B49 SYS_RESET#
A50 LPC_SERIRQ B50 CB_RESET#
A51 GND (FIXED) B51 GND (FIXED)
A52 RSVD B52 RSVD
A53 RSVD B53 RSVD
A54 GPI0 B54 GPO1
A55 RSVD B55 RSVD
A56 RSVD B56 RSVD
A57 GND B57 GPO2
A58 PCIE_TX3+ B58 PCIE_RX3+
A59 PCIE_TX3- B59 PCIE_RX3 A60 GND (FIXED) B60 GND (FIXED)
A61 PCIE_TX2+ B61 PCIE_RX2+
A62 PCIE_TX2- B62 PCIE_RX2-
A63 GPI1 B63 GPO3
A64 PCIE_TX1+ B64 PCIE_RX1+
A65 PCIE_TX1- B65 PCIE_RX1 A66 GND B66 WAKE0#
A67 GPI2 B67 WAKE1#
A68 PCIE_TX0+ B68 PCIE_RX0+
A69 PCIE_TX0- B69 PCIE_RX0-
A70 GND(FIXED) B70 GND (FIXED)
A71 LVDS_A0+ B71 DDI0_PAIR0+
A72 LVDS_A0- B72 DDI0_PAIR0 A73 LVDS_A1+ B73 DDI0_PAIR1+
A74 LVDS_A1- B74 DDI0_PAIR1 A75 LVDS_A2+ B75 DDI0_PAIR2+
A76 LVDS_A2- B76 DDI0_PAIR2 A77 LVDS_VDD_EN B77 DDI0_PAIR4+
A78 LVDS_A3+ B78 DDI0_PAIR4 A79 LVDS_A3- B79 LVDS_BKLT_EN
A80 GND (FIXED) B80 GND (FIXED)
A81 LVDS_A_CK+ B81 DDI0_PAIR3+
A82 LVDS_A_CK- B82 DDI0_PAIR3 A83 LVDS_I2C_CK B83 LVDS_BKLT_CTRL
A84 LVDS_I2C_DAT B84 VCC_5V_SBY
A85 GPI3 B85 VCC_5V_SBY
Row A Row B
Row A Row B
A86 RSVD B86 VCC_5V_SBY
A87 eDP_HPD B87 VCC_5V_SBY
A88 PCIE_CLK_REF+ B88 BIOS_DIS1#
A89 PCIE0_CK_REF- B89 DD0_HPD
A90 GND (FIXED) B90 GND (FIXED)
A91 SPI_POWER B91 DDI0_PAIR5+
A92 SPI_MISO B92 DDI0_PAIR5 A93 GPO0 B93 DDI0_PAIR6+
A94 SPI_CLK B94 DDI0_PAIR6 A95 SPI_MOSI B95 DDI0_DDC_AUX_SEL
A96 TPM_PP B96 USB_HOST_PRSNT
A97 TYPE10# B97 SPI_CS#
A98 SER0_TX B98 DDI0_CTRLCLK_AUX+
A99 SER0_RX B99 DDI0_CTRLCLK_AUX A100 GND (FIXED) B100 GND (FIXED)
A101 SER1_TX B101 FAN_PWMOUT
A102 SER1_RX B102 FAN_TACHIN
A103 LID# B103 SLEEP#
A104 VCC_12V B104 VCC_12V
A105 VCC_12V B105 VCC_12V
A106 VCC_12V B106 VCC_12V
A107 VCC_12V B107 VCC_12V
A108 VCC_12V B108 VCC_12V
A109 VCC_12V B109 VCC_12V
A110 GND (FIXED) B110 GND (FIXED)
Page 14
www.dfi .comChapter 3 Hardware Installation
14
Chapter 3
COM Express Connector Signal Description
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
AC/HAD_RST# A30 O CMOS 3.3V Suspend/3.3V Connect to CODEC pin 11 RESET# Reset output to CODEC, active low.
AC/HDA_SYNC A29 O CMOS 3.3V/3.3V Connect to CODEC pin 10 SYNC Sample-synchronization signal to the CODEC(s).
AC/HDA_BITCLK A32 I/O CMOS 3.3V/3.3V Connect to CODEC pin 6 BIT_CLK Serial data clock generated by the external CODEC(s).
AC/HDA_SDOUT A33 O CMOS 3.3V/3.3V Connect to CODEC pin 5 SDATA_OUT Serial TDM data output to the CODEC.
AC/HDA_SDIN2 B28 I/O CMOS 3.3V Suspend/3.3V Connect 33 ƻ in series to CODEC2 pin 8 SDATA_IN
AC/HDA_SDIN1 B29 I/O CMOS 3.3V Suspend/3.3V Connect 33 ƻ in series to CODEC1 pin 8 SDATA_IN
AC/HDA_SDIN0 B30 I/O CMOS 3.3V Suspend/3.3V Connect 33 ƻ in series to CODEC0 pin 8 SDATA_IN
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
GBE0_MDI0+ A13 I/O Analog 3.3V max Suspend
GBE0_MDI0- A12 I/O Analog 3.3V max Suspend
GBE0_MDI1+ A10 I/O Analog 3.3V max Suspend
GBE0_MDI1- A9 I/O Analog 3.3V max Suspend
GBE0_MDI2+ A7 I/O Analog 3.3V max Suspend
GBE0_MDI2- A6 I/O Analog 3.3V max Suspend
GBE0_MDI3+ A3 I/O Analog 3.3V max Suspend
GBE0
_
MDI3-
A
2I
/
O Analog3.3V max Suspend
GBE0_ACT# B2 OD CMOS 3.3V Suspend/3.3V
Connect to LED and recommend current limit
resistor 150ȟ to 3.3VSB
Gigabit Ethernet Controller 0 activity indicator, active low.
GBE0_LINK# A8 OD CMOS 3.3V Suspend/3.3V NC Gigabit Ethernet Controller 0 link indicator, active low.
GBE0_LINK100# A4 OD CMOS 3.3V Suspend/3.3V
Connect to LED and recommend current limit
resistor 150ȟ to 3.3VSB
Gigabit Ethernet Controller 0 100 Mbit / sec link indicator, active low.
GBE0_LINK1000# A5 OD CMOS 3.3V Suspend/3.3V
Connect to LED and recommend current limit
resistor 150ȟ to 3.3VSB
Gigabit Ethernet Controller 0 1000 Mbit / sec link indicator, active low.
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
SATA0_TX+ A16 O SATA AC coupled on Module AC Coupling capacitor
SATA0_TX- A17 O SATA AC coupled on Module AC Coupling capacitor
SATA0_RX+ A19 I SATA AC coupled on Module AC Coupling capacitor
SATA0_RX- A20 I SATA AC coupled on Module AC Coupling capacitor
SATA1_TX+ B16 O SATA AC coupled on Module AC Coupling capacitor
SATA1_TX- B17 O SATA AC coupled on Module AC Coupling capacitor
SATA1_RX+ B19 I SATA AC coupled on Module AC Coupling capacitor
SATA1_RX- B20 I SATA AC coupled on Module AC Coupling capacitor
ATA_ACT# A28 I/O CMOS 3.3V / 3.3V PU 10K to 3.3V
Connect to LED and recommend current limit
resistor 220ƻ to 3.3V
ATA (parallel and serial) or SAS activity indicator, active low.
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
PCIE_TX0+ A68 AC Coupling capacitor
PCIE_TX0- A69 AC Coupling capacitor
PCIE_RX0+ B68
PCIE_RX0- B69
PCIE_TX1+ A64 AC Coupling capacitor
PCIE_TX1- A65 AC Coupling capacitor
PCIE_RX1+ B64
PCIE_RX1- B65
PCIE_TX2+ A61 AC Coupling capacitor
PCIE_TX2- A62 AC Coupling capacitor
A
C97/HDA Signals Description
s
Serial TDM data inputs from up to 3 CODECs.
Gigabit Ethernet Signals Description
s
Gigabit Ethernet Controller 0: Media Dependent Interface Differential
Pairs 0,1,2,3. The MDI can operate in 1000, 100 and 10 Mbit / sec
modes. Some pairs are unused in some modes, per the following:
1000BASE-T 100BASE-TX 10BASE-T
MDI[0]+/- B1_DA+/- TX+/- TX+/ MDI[1]+/- B1_DB+/- RX+/- RX+/ MDI[2]+/- B1_DC+/ MDI[3]+/- B1_DD+/-
Serial ATA or SAS Channel 1 receive differential pair.
SATA Signals Description
s
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 1
PCI Express Lanes Signals Description
s
Serial ATA or SAS Channel 0 transmit differential pair.
Serial ATA or SAS Channel 0 receive differential pair.
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 0
Serial ATA or SAS Channel 1 transmit differential pair.
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 0
Connect to SATA1 Conn RX pin
Connect to SATA0 Conn TX pin
Connect to PCIE device or slot
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 2
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 1
Pin Types
I Input to the Module
O Output from the Module
I/O Bi-directional input / output signal
OD Open drain output
Connect to Magnetics Module MDI0+/-
Connect to Magnetics Module MDI1+/-
Connect to Magnetics Module MDI2+/-
Connect to Magnetics Module MDI3+/-
Connect to SATA0 Conn RX pin
Connect to SATA1 Conn TX pin
Device - Connect AC Coupling cap 0.1uF
Slot - Connect to PCIE Conn pin
Connect to PCIE device or slot
Device - Connect AC Coupling cap 0.1uF
Slot - Connect to PCIE Conn pin
Connect to PCIE device or slot
Page 15
www.dfi .comChapter 3 Hardware Installation
15
Chapter 3
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
PCI Express Lanes Signals Description
s
PCIE_RX2+ B61
PCIE_RX2- B62
PCIE_TX3+ A58 NA NA
PCIE_TX3- A59 NA NA
PCIE_RX3+ B58 NA NA
PCIE_RX3- B59 NA NA
PCIE0_CK_REF+ A88
PCIE0_CK_REF- A89
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
EXCD0_CPPE# A49 PU 10k to 3.3V
EXCD1_CPPE# B48 PU 10k to 3.3V
EXCD0_PERST# A48
EXCD1_PERST# B47
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
DDI1_PAIR0+/DP0_LANE0+ B71 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR0-/DP0_LANE0- B72 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR1+/DP0_LANE1+ B73 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR1-/DP0_LANE1- B74 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR2+/DP0_LANE2+ B75 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR2-/DP0_LANE2- B76 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR3+/DP0_LANE3+ B81 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR3-/DP0_LANE3- B82 Connect AC Coupling Capacitors 0.1uF to Device
DDI1_PAIR4+ B77 NA NA
DDI1_PAIR4- B78 NA NA
DDI1_PAIR5+ B91 NA NA
DDI1_PAIR5- B92 NA NA
DDI1_PAIR6+ B93 NA NA
DDI1_PAIR6- B94 NA NA
I/O PCIE AC coupled on Module
PD 49.9K to GND
(S/W IC between Rpu/PCH)
Connect to DP AUX+ DP AUX+ function if DDI1_DDC_AUX_SEL is no connect
I/O OD CMOS 3.3V / 3.3V
PU 2.2K to 3.3V, PD 49.9K to
GND
Connect to HDMI/DVI I2C CTRLCLK HDMI/DVI I2C CTRLCLK if DDI1_DDC_AUX_SEL is pulled high
I/O PCIE AC coupled on Module PU 100K to 3.3V Connect to DP AUX- DP AUX- function if DDI1_DDC_AUX_SEL is no connect
I/O OD CMOS 3.3V / 3.3V PU 2.2K to 3.3V/PU 100K to 3.3V Connect to HDMI/DVI I2C CTRLDATA HDMI/DVI I2C CTRLDATA if DDI1_DDC_AUX_SEL is pulled high
DDI1_HPD/DP0_HPD B89 I CMOS 3.3V / 3.3V PD 1M to GND PD 1M and Connect to device Hot Plug Detect DDI Hot-Plug Detect
DDI1_DDC_AUX_SEL B95 I CMOS 3.3V / 3.3V PD 1M to GND PU 100K to 3.3V for DDC(HDMI/DVI)
Selects the function of DDI1_CTRLCLK_AUX+ and DDI1_CTRLDATA_AUX-.
This pin shall have a 1M pull-down to
logic ground on the Module. If this input is floating the AUX pair is
used for the DP AUX+/- signals. If pulled-high the AUX pair
contains the CRTLCLK and CTRLDATA signals
************************************************************
DDI[n]_DDC_AUX_SEL shall be pulled to 3.3V on the Carrier with a 100K Ohm
resistor to configure the DDI[n]_AUX pair as the DDC channel.
Carrier DDI[n]_DDC_AUX_SEL should be connected to pin 13 of the DisplayPort
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 3 (NA for BT9A3)
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 3 (NA for BT9A3)
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 2
Device - Connect AC Coupling cap 0.1uF
Slot - Connect to PCIE Conn pin
B99
O PCIE PCIE Reference clock output for all PCI Express and PCI Express Graphics lanes.
NA for BT9A3
NA for BT9A3
ExpressCard Signals Description
s
I CMOS 3.3V /3.3V PCI ExpressCard: PCI Express capable card request, active low, one per card
O CMOS 3.3V /3.3V PCI ExpressCard: reset, active low, one per card
NA for BT9A3
O PCIE AC coupled off Module DDI 1 Pair 3 differential pairs/Serial Digital Video B clock output differential pair.
DDI 1 Pair 1 differential pairs/Serial Digital Video B green output differential pair
DDI1_CTRLCLK_AUX+/DP0_AUX+ B98
DDI1_CTRLCLK_AUX-/DP0_AUX-
DDI Signals Descriptions
O PCIE AC coupled off Module DDI 1 Pair 0 differential pairs/Serial Digital Video B red output differential pair
O PCIE AC coupled off Module DDI 1 Pair 2 differential pairs/Serial Digital Video B blue output differential pair
O PCIE AC coupled off Module
Connect to PCIE device, PCIe CLK Buffer or slot
Page 16
www.dfi .comChapter 3 Hardware Installation
16
Chapter 3
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
USB0+ A46
USB0- A45
USB1+ B46
USB1- B45
USB2+ A43
USB2- A42
USB3+ B43
USB3- B42
USB4+ A40
USB4- A39
USB5+ B40
USB5- B39
USB6+ A37
USB6- A36
USB7+ B37
USB7- B36
USB_0_1_OC# B44 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3A Connect to Overcurrent of USB Power Switch
USB over-current sense, USB channels 0 and 1. A pull-up for this line
shall be present on the Module. An open drain driver from a USB
current monitor on the Carrier Board may drive this line low. Do not
pull this line high on the Carrier Board.
USB_2_3_OC# A44 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3A Connect to Overcurrent of USB Power Switch
USB over-current sense, USB channels 2 and 3. A pull-up for this line
shall be present on the Module. An open drain driver from a USB
current monitor on the Carrier Board may drive this line low. Do not
pull this line high on the Carrier Board.
USB_4_5_OC# B38 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3A Connect to Overcurrent of USB Power Switch
USB over-current sense, USB channels 4 and 5. A pull-up for this line
shall be present on the Module. An open drain driver from a USB
current monitor on the Carrier Board may drive this line low. Do not
pull this line high on the Carrier Board.
USB_6_7_OC# A38 I CMOS 3.3V Suspend/3.3V PU 10k to 3.3A Connect to Overcurrent of USB Power Switch
USB over-current sense, USB channels 6 and 7. A pull-up for this line
shall be present on the Module. An open drain driver from a USB
current monitor on the Carrier Board may drive this line low. Do not
pull this line high on the Carrier Board.
USB_SSTX0+ D4 NA NA
USB_SSTX0- D3 NA NA
USB_SSRX0+ C4 NA NA
USB_SSRX0- C3 NA NA
USB_SSTX1+ D7 NA NA
USB_SSTX1- D6 NA NA
USB_SSRX1+ C7 NA NA
USB_SSRX1- C6 NA NA
USB_HOST_PRSNT B96 I CMOS 3.3V Suspend/3.3V NA NA
Module USB client may detect the presence of a USB host. A high value(NA for BT9A3)
indicates that a host is present.
USB differential pairs 5
USB differential pairs 3
I/O USB 3.3V Suspend/3.3V USB differential pairs 2
I/O USB 3.3V Suspend/3.3V USB differential pairs 1
USB Signals Description
s
I/O USB 3.3V Suspend/3.3V USB differential pairs 0
I/O USB 3.3V Suspend/3.3V USB differential pairs 4
I/O USB 3.3V Suspend/3.3V
AC coupled off Modul Additional receive signal differential pairs for the SuperSpeed USB data path.(NA for BT9A3)
O PCIE AC coupled on Module Additional transmit signal differential pairs for the SuperSpeed USB data path.(NA for BT9A3)
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
I/O USB 3.3V Suspend/3.3V
USB differential pairs 7, USB7 may be configured as a USB client or as a host, or both, at the
Module designer's discretion.
I/O USB 3.3V Suspend/3.3V USB differential pairs 6
I/O USB 3.3V Suspend/3.3V
O PCIE AC coupled on Module Additional transmit signal differential pairs for the SuperSpeed USB data path.(NA for BT9A3)
I PCIE AC coupled off Modul Additional receive signal differential pairs for the SuperSpeed USB data path.(NA for BT9A3)
I PCIE
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Connect 90ಳ @100MHz Common Choke in series
and ESD suppressors to GND to USB connector
Page 17
www.dfi .comChapter 3 Hardware Installation
17
Chapter 3
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
LVDS_A0+ A71
LVDS_A0- A72
LVDS_A1+ A73
LVDS_A1- A74
LVDS_A2+ A75
LVDS_A2- A76
LVDS_A3+ A78
LVDS_A3- A79
LVDS_A_CK+ A81
LVDS_A_CK- A82
LVDS_VDD_EN A77 O CMOS 3.3V / 3.3V
Connect to enable control of LVDS panel power
circuit
LVDS panel power enable
LVDS_BKLT_EN B79 O CMOS 3.3V / 3.3V
Connect to enable control of LVDS panel backlight
power circuit.
LVDS panel backlight enable
LVDS_BKLT_CTRL B83 O CMOS 3.3V / 3.3V
Connect to brightness control of LVDS panel
backlight power circuit.
LVDS panel backlight brightness control
LVDS_I2C_CK A83 I/O OD CMOS 3.3V / 3.3V PU 2.2K to 3.3V Connect to DDC clock of LVDS panel I2C clock output for LVDS display use
LVDS_I2C_DAT A84 I/O OD CMOS 3.3V / 3.3V PU 2.2K to 3.3V Connect to DDC data of LVDS panel I2C data line for LVDS display use
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
LPC_AD0 B4
LPC_AD1 B5
LPC_AD2 B6
LPC_AD3 B7
LPC_FRAME# B3 O CMOS 3.3V / 3.3V LPC frame indicates the start of an LPC cycle
LPC_DRQ0# B8
LPC_DRQ1# B9
LPC_SERIRQ A50 I/O CMOS 3.3V / 3.3V PU 8.2K to 3.3V LPC serial interrupt
LPC_CLK B10 O CMOS 3.3V / 3.3V LPC clock output - 33MHz nominal
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
SPI_CS# B97 O CMOS 3.3V Suspend/3.3V
Connect a series resistor 33
ȟ
to Carrier
Board SPI Device CS# pin
Chip select for Carrier Board SPI - may be sourced from chipset SPI0 or SPI1
SPI_MISO A92 I CMOS 3.3V Suspend/3.3V
Connect a series resistor 33
ȟ
to Carrier
Board SPI Device SO pin
Data in to Module from Carrier SPI
SPI_MOSI A95 O CMOS 3.3V Suspend/3.3V
Connect a series resistor 33
ȟ
to Carrier
Board SPI Device SI pin
Data out from Module to Carrier SPI
SPI_CLK A94 O CMOS 3.3V Suspend/3.3V
Connect a series resistor 33
ȟ
to Carrier
Board SPI Device SCK pin
Clock from Module to Carrier SPI
SPI_POWER A91 O 3.3V Suspend/3.3V
Power supply for Carrier Board SPI – sourced from Module – nominally
3.3V. The Module shall provide a minimum of 100mA on SPI_POWER.
Carriers shall use less than 100mA of SPI_POWER. SPI_POWER
shall only be used to power SPI devices on the Carrier
BIOS
_
DIS0#
A
34
BIOS_DIS1# B88
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
SER0_TX A98 O CMOS
5V / 12V(design 3.3v~5V
tolerant)
PD 4.7K General purpose serial port 0 transmitter
SER0_RX A99 I CMOS
5V / 12V(design 3.3v~5
V
tolerant
)
PU 47K to 3.3V General purpose serial port 0 receiver
SER1_TX A101 O CMOS
5V / 12V(design 3.3v~5V
tolerant)
PD 4.7K General purpose serial port 1 transmitter
SER1_RX A102 I CMOS
5V / 12V(design 3.3v~5V
tolerant)
PU 47K to 3.3V General purpose serial port 1 receiver
O LVDS LVDS
LVDS Channel A differential clockO LVDS LVDS
LVDS Signals Description
s
O LVDS LVDS
LVDS Channel A differential pairs
O LVDS LVDS
O LVDS LVDS
Connect to LVDS connector
Connect to LVDS connector
Connect to LVDS connector
Connect to LVDS connector
Connect to LVDS connector
I/O CMOS 3.3V / 3.3V
3.3V / 3.3V LPC serial DMA request
SPI Signals Description
s
I CMOS
LPC multiplexed address, command and data bus
Connect to LPC device
Serial Interface Signals Description
s
I CMOS
NA
Selection straps to determine the BIOS boot device.
The Carrier should only float these or pull them low, please refer to
COM Express Module Base Specification Revision 2.1 for strapping options of BIOS disable signals.
LPC Signals Description
s
Page 18
www.dfi .comChapter 3 Hardware Installation
18
Chapter 3
ȟ
ȟ
ȟ
ȟ
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
I2C_CK B33 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3V3A_EC General purpose I2C port clock output
I2C_DAT B34 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3V3A_EC General purpose I2C port data I/O line
SPKR B32 O CMOS 3.3V / 3.3V
Output for audio enunciator - the "speaker" in PC-AT systems.
This port provides the PC beep signal and is mostly intended for
debugging purposes.
WDT B27 O CMOS 3.3V / 3.3V Output indicating that a watchdog time-out event has occurred.
FAN_PWNOUT B101 O OD CMOS 3.3V / 12V Fan speed control. Uses the Pulse Width Modulation (PWM) technique to control the fan's RPM.
FAN_TACHIN B102 I OD CMOS 3.3V / 12V Fan tachometer input for a fan with a two pulse output.
TPM_PP A96 I CMOS 3.3V / 3.3V
T
rusted Platform Module (TPM) Physical Presence pin. Active high.
TPM chip has an internal pull down. This signal is used to indicate
Physical Presence to the TPM.
(
NC for BT9A3
)
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
PWRBTN# B12 I CMOS 3.3V Suspend/3.3V PU 10K to 3V3A_EC
A falling edge creates a power button event. Power button events can
be used to bring a system out of S5 soft off and other suspend states,
as well as powering the system down.
SYS_RESET# B49 I CMOS 3.3V Suspend/3.3V PU 10K to 3V3A
Reset button input. Active low request for Module to reset and reboot.
May be falling edge sensitive. For situations when SYS_RESET# is
not able to reestablish control of the system, PWR_OK or a power
cycle may be used.
CB_RESET# B50 O CMOS 3.3V Suspend/3.3V
Reset output from Module to Carrier Board. Active low. Issued by
Module chipset and may result from a low SYS_RESET# input, a low
PWR_OK input, a VCC_12V power input that falls below the minimum
specification, a watchdog timeout, or may be initiated by the Module
software.
PWR_OK B24 I CMOS 3.3V / 3.3V PU 10K to 3.3V
Power OK from main power supply. A high value indicates that the
power is good. This signal can be used to hold off Module startup to
allow Carrier based FPGAs or other configurable devices time to be
programmed.
SUS_STAT# B18 O CMOS 3.3V Suspend/3.3V Indicates imminent suspend operation; used to notify LPC devices.
SUS_S3# A15 O CMOS 3.3V Suspend/3.3V
Indicates system is in Suspend to RAM state. Active low output. An
inverted copy of SUS_S3# on the Carrier Board may be used to
enable the non-standby power on a typical ATX supply.
SUS_S4# A18 O CMOS 3.3V Suspend/3.3V Indicates system is in Suspend to Disk state. Active low output.
SUS_S5# A24 O CMOS 3.3V Suspend/3.3V Indicates system is in Soft Off state.
WAKE0# B66 I CMOS 3.3V Suspend/3.3V NC/PU 10K to 3.3A PCI Express wake up signal.
WAKE1# B67 I CMOS 3.3V Suspend/3.3V
General purpose wake up signal. May be used to implement wake-up
on PS2 keyboard or mouse activity.
BATLOW# A27 I CMOS 3.3V Suspend/ 3.3V PU 10K to 3.3A
Indicates that external battery is low.
This port provides a battery-low signal to the Module for orderly
transitioning to power saving or power cut-off ACPI modes.
LID# A103 I OD CMOS 3.3V Suspend/12V PU 10K to 3V3A_EC LID switch. Low active signal used by the ACPI operating system for a LID switch.
SLEEP# B103 I OD CMOS 3.3V Suspend/12V PU 10K to 3V3A_EC
Sleep button. Low active signal used by the ACPI operating system to bring the
system to sleep state or to wake it up again.
THRM# B35 I CMOS 3.3V / 3.3V PU 10K to 3.3V Input from off-Module temp sensor indicating an over-temp situation.
THRMTRIP# A35 O CMOS 3.3V / 3.3V Active low output indicating that the CPU has entered thermal shutdown.
SMB_CK B13 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3V3A_EC System Management Bus bidirectional clock line.
SMB_DAT B14 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3V3A_EC System Management Bus bidirectional data line.
SMB_ALERT# B15 I CMOS 3.3V Suspend/3.3V
System Management Bus Alert – active low input can be used to
generate an SMI# (System Management Interrupt) or to wake the system.
Power and System Management Signals Description
s
Miscellaneous Signal Descriptions
Page 19
www.dfi .comChapter 3 Hardware Installation
19
Chapter 3
ȟ
ȟ
ȟ
ȟ
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
GPO0 A93
GPO1 B54
GPO2 B57
GPO3 B63
GPI0 A54 PU 100K to 3.3V
GPI1 A63 PU 100K to 3.3V
GPI2 A67 PU 100K to 3.3V
GPI3 A85 PU 100K to 3.3V
Signal Pin# Pin Type Pwr Rail /Tolerance BT9A3 Series Carrier Board Description
VCC_12V
A
104~A10
9
B104~B109
Power 4.75V – 20.0V 4.75V – 20.0V
Primary power input: +12V nominal. All available VCC_12V pins on the connector(s) shall be used.
The module supplies a wide range of power from 4.75V to 20.0V.
VCC_5V_SBY B84~B87 Power 4.75V - 5.25V 4.75V - 5.25V
Standby power input: +5.0V nominal. If VCC5_SBY is used, all
available VCC_5V_SBY pins on the connector(s) shall be used. Only
used for standby and suspend functions. May be left unconnected if
these functions are not used in the system design.
VCC_RTC A47 Power 2.0V - 3.3V 2.0V - 3.3V Real-time clock circuit-power input. Nominally +3.0V.
GND
A1, A11, A21, A31, A41,
A51, A57, A60, A66, A70,
A80, A90, A100, A110, B1,
B11, B21 ,B31, B41, B51,
B60, B70, B80, B90, B100,
B110
Power
Ground - DC power and signal and AC signal return path.
All available GND connector pins shall be used and tied to Carrier
Board GND plane.
Power and GND Signal Descriptions
I CMOS PU 100K to 3V3 General purpose input pins.
GPIO Signals Description
s
O CMOS 3.3V / 3.3V General purpose output pins.
Loading...