Figure B
Figure D
Figure E
Figure A
Figure
C
READ ALL INSTRUCTIONS BEFORE FIRST USE.
Ages 2 Years – 6 Years
CAUTION: ADULT ASSEMBLY REQUIRED.
WARNING: IMPORTANT! KEEP FOR FUTURE REFERENCE!
• SUFFOCATION AND STRANGULATION HAZARD.
• Gaps in and around bed rails have entrapped young children and killed
infants.
• NEVER use with children younger than 2 years old. Use ONLY with older
children who can get in and out of adult bed without help. NEVER use in
place of crib.
• NEVER use unless bed rail is tight against mattress, without gaps, and at
least 9 in. from headboard and footboard. Do not fill gaps with pillows,
blankets, or other items that can suffocate children.
• NEVER use on toddler bed, bunk bed, waterbed, or bed with inflatable
mattress. Use ONLY on adult bed.
• Discontinue use if damaged, broken, or if parts are missing.
Please follow these six easy steps to assemble this rail very quickly and WITHOUT TOOLS!
To Start: Lay the 2 Hinged Pieces and the
2 Curved Bars of the rail on the floor or table,
so that the 3 Cross Bars line up (Figure A).
ASSEMBLY INSTRUCTIONS
#BR43
Slide Mesh Cover across the left side of rail
(Figure E), then zip it closed (Figure C).
4
Starting from the center of the rail, slide
Mesh Cover over the right side of rail
(Figure B), then zip it closed (Figure C).
2
Connect Curved Bars to the Hinged Pieces,
making sure they lock into place (Figure A).
1
Connect the 3 Cross Bars, making sure all 3
lock into place (Figure D).
3
safe sleeper™ bed rail
Figure K
Figure K
Figure J
Figure J
mattress
anchor plate
box spring
Figure I
Figure HFigure G
Figure F
ASSEMBLY INSTRUCTION CONTINUED
Machine wash cold and hang dry, or surface wash with damp cloth.
CLEANING INSTRUCTIONS
INSTALLATION AND USE INSTRUCTIONS FOR BEDS WITH BOX SPRINGS
01. Extend Anchor Strap and Plate to maximum length.
02. Insert Hinged Legs into place between mattress and box spring.
03. Extend Anchor Strap and Plate so that Anchor Plate is in position for
tightening. (Figure I)
04. Pull red striped tag toward you while pushing the Anchor Plate forward with
opposite hand, pressing Anchor Plate firmly against the mattress and box
spring. (Figure J)
05. Release grip on the red striped tag and pull the lower strap toward you until
Anchor Plate is snug against mattress and box spring. (Figure K)
IMPORTANT: To insure bed rail is tight as possible against mattress and
box spring, raise the mattress and tighten the strap slightly. Then lower the
mattress and pull the anchor plate back and firmly into place. Repeat this
step as needed and until tight. Mattress and box spring must be aligned.
06. Tuck remaining length of strap under the mattress, out of the way of children.
07. Lowering rail after installed on bed: This rail is designed with childproof
hinges for added safety. Therefore – to lower your rail - you must raise EACH
(both left and right) spring-loaded hinge at the same time. The hinges each
display an arrow pointing upwards in the direction you must raise the hinge to
disengage it. Once each spring is raised, you may gently lower the rail with
ease. This will allow you to easily change or make the bed. When you raise
the rail back to the upright position, the locks will automatically pop back into
place for safety.
© 2015 DEX Products, Inc., dexbaby™, safe sleeper™, and the footprint logo are trademarks of DEX Products, Inc.
safe sleeper™ bed rail is Patent Pending. Patent infringement will be prosecuted to the full extent of the law. Made in China. 0715
DEX Products, Inc.
www.dexbaby.com 800.546.1996 2019 East Monte Vista Ave. Suite #500, Vacaville, CA 95688
Open Hinges until they lock firmly into place.
Then line up the 2 Legs with Hinges (Figure F).
NOTE: Make sure Anchor Straps are not
twisted before proceeding.
5
Connect the 2 Legs to the Hinges (Figure G).
Make sure silver button protrudes from hole
in Hinge as they lock into place (Figure H).
6
With the Mesh Cover zipped shut and the Hinges and Legs locked firmly into place,
assembly is now complete. Proceed to installation instructions.
Loading...