Page 1
DWV902L
www .
.eu
DWV902M
Page 2
Figure 1
r
a
p
o
n
k
c
Figure 2
b
m
l
d
e
j
q
h
s
f
h
bb
t
i
g
u
Figure 3
t
g
j
j
Figure 4
n
p
Figure 5
v
Ø 20
g
w
o
v
1
Page 3
Figure 6 Figure 7
x
Figure 8 Figure 9
r
q
y
i
Figure 10 Figure 11
z
aa
2
b
s
j
Page 4
ENGLISH
HEAVY-DUTY CONSTRUCTION DUST EXTRACTOR
DWV902L, DWV902M
Congratulations!
You have chosen a DEWALT product. Years of experience, thorough product development and innovation
make DEWALT one of the most reliable partners for professional power tool users.
Technical Data
DWV902L DWV902L DWV902M DWV902M
QS/GB LX QS/GB LX
Voltage V 230 – 230 –
U.K. & Ireland V 230 115 230 115
Type 1 1 1 1
Rated power W 1400 1400 1400 1400
Max power W 3600 1840 3600 1840
Power, normal operation (EN 60335-2-69) W 1200 1065 1200 1065
Frequency Hz 50 50 50 50
Protective class IPX4 IPX4 IPX4 IPX4
Container capacity l 38 38 38 38
Filling quantity (liquid) l 18.4 18.4 18.4 18.4
Flow rate (max at blower) l/s 68 64 68 64
Negative pressure (max at blower) kPa 21 20 21 20
Flow rate (per EN 60335-2-69) l/s 32.6 31.3 32.6 31.3
Negative pressure (per EN 60335-2-69) kPa 18.6 16.8 18.6 16.8
Filter surface m² 0.4 0.4 0.4 0.4
Power connection data of power tool W 2200 440 2200 440
Hose length m 4.1 4.1 4.1 4.1
Hose diameter mm 32 32 32 32
Weight kg 15 15 15 15
LPA (sound pressure) dB(A)
KPA (sound pressure uncertainty) dB(A)
LWA (sound power) dB(A)
KWA (sound power uncertainty) dB(A)
73 73 73 73
3 3 3 3
87 87 87 87
3 3 3 3
Defi nitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
24
CAUTION: Indicates a potentially
NOTICE: Indicates a practice not
Denotes risk of fire.
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Page 5
ENGLISH
Important Safety Instructions
EC-Declaration of Conformity
MACHINERY DIRECTIVE
DWV902L, DWV902M
DEWALT declares that these products described
under Technical Data are in compliance with:
2006/42/EC, EN 60335-2-69.
These products also comply with Directive
2004/108/EC and 2011/65/EU. For more
information, please contact DEWALT at the following
address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
DEWALT.
Horst Grossmann
Vice President Engineering and
Product Development
DEWALT, Richard-Klinger-Strasse 11,
D-65510, Idstein, Germany
13.06.2012
WARNING: To reduce the risk of injury,
Important Safety Instructions
WARNING! Read all safety warnings
SAVE ALL WARNINGS AND INSTRUCTIONS
BEFORE USING THIS APPLIANCE, READ AND FOLLOW ALL
INSTRUCTIONS.
WARNING: Operators shall be
WARNING: To reduce the risk of
• Before use, operators shall be provided with
information, instruction and training for the
use of the machine and the substances for
which it is to be used, including the safe
read the instruction manual.
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
FOR FUTURE REFERENCE
adequately instructed on the use of
these machines.
electric shock. Do not expose to rain.
Store indoors.
method of removal and disposal of the
material collected.
• Operators should observe any safety
regulations appropriate to the materials being
handled.
• Do not leave the appliance when it is
connected to a power source. Unplug it from
outlet when not in use and before servicing.
• Do not allow the appliance to be used as a
toy. Pay close attention when the appliance is
used by or near children.
• Use this appliance ONLY as described in the
manual. Use only D
attachments.
• Do not use this appliance with a damaged
cord or plug. If the appliance is not working
correctly, or if it has been dropped,
damaged, left outdoors, or dropped in water,
return it to a service center.
• Do not pull or carry this appliance by the
cord, use the cord as a handle, close a door
on the cord, or pull the cord around sharp
edges or corners. Do not run the appliance
over the cord. Keep cord away from heated
surfaces.
• Do not unplug this appliance by pulling on
the cord. To unplug, grasp the plug, not the
cord.
• Do not handle the plug or appliance with wet
hands.
• Do not put any objects into the openings of
the appliance. Do not use the appliance with
any opening blocked; keep free of dust, lint,
hair and anything else that may reduce air
flow.
• Keep hair, loose clothing, fingers, and all
body parts away from the openings and
moving parts.
• Turn off all controls before unplugging
appliance.
• Use extra care when cleaning on stairs.
• Do not use the appliance to pick up
flammable or combustible liquids, such as
gasoline, or use in areas where flammable or
combustible liquids are present.
• Static shocks are possible in dry areas or
when the relative humidity of the air is low.
This is only temporary and does not affect
the use of the vacuum. To reduce the
frequency of static shocks, add moisture to
the air with a console, installed humidifier or
use DWV9316-XJ non-static hose accessory.
• To avoid spontaneous combustion, empty
canister after each use.
EWALT recommended
SAVE THESE INSTRUCTIONS
25
Page 6
ENGLISH
Additional Safety Rules
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or hot
ashes.
• Do not use to vacuum combustible explosive
materials, such as coal, grain, or other finely
divided combustible material.
• Do not use to vacuum hazardous, toxic or
carcinogenic materials, such as asbestos or
pesticide.
• Never pick up explosive liquids (e.g. gasoline,
diesel fuel, heating oil, paint thinner, etc.),
acids or solvents.
• Do not use vacuum without filters in place,
except as described under Wet Pickup
Applications.
• Some wood contains preservatives which
can be toxic. Take extra care to prevent
inhalation and skin contact when working
with these materials. Request and follow any
safety information available from your material
supplier.
• Do not use vacuum as a step ladder.
• Do not place heavy objects on vacuum.
Markings on Dust Extractor
The following pictograms are shown on the
appliance:
Read instruction manual before use.
WARNING: This appliance contains
harmful dust. The emptying and
maintenance, including the removal of
the dust bag, may only be executed
by trained personnel wearing suitable
protection equipment. Do not switch on
until the complete filter system has been
installed.
Class L dust extractors are suitable to extract dry,
non-combustable dusts with workpace limit values
of >1mg/m³.
Class M dust extractors are suitable to extract dry,
non-combustable dusts with workpace limit values
of ≥ 0.1 mg/m³.
DATE CODE POSITION (FIG. 1)
The date code (bb), which also includes the year of
manufacture, is printed into the housing.
Example:
2012 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Dust extractor
1 Hose
1 DWV9210-XJ connector kit
2 Filters
1 Instruction manual
1 Exploded drawing
• Check for damage to the dust extractor, parts
or accessories which may have occurred
during transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fi g. 1)
WARNING: Never modify the power
a. Top handle/cord wrap
b. Power cord
c. Vacuum head
d. Canister latch
e. Wheel
f. Canister
g. Suction hose
h. Casters (one equipped with parking brake)
i. Filters
j. Twist-lock hose inlet
k. Hose clip
l. Front handle
m. Outlet for power tools
n. Variable suction dial
o. On/off/tool control switch
p. Flow alarm adjustment (Class M models only)
q. Telescoping handle release button
r. Telescoping handle
s. Inlet plug (Class M models only)
t. Bag
appliance or any part of it. Damage or
personal injury could result.
26
Page 7
ENGLISH
u. DWV9210-XJ connector kit (includes DWV9000,
DWV9120, DWV9130)
ANTI-STATIC HOSE OPTION
The DWV902L and DWV902M are each equipped
with an anti-static grounding system. An anti-static
hose must be purchased at extra cost from your
authorised service center. This hose (DWV9316-XJ)
fits into the dust extractor system the same way as
the standard hose. To contact your seller or check
the location of your nearest authorised D
repair agent in the DEWALT catalogue or contact
your DEWALT office at the address indicated in this
manual.
INTENDED USE
These vacuums are used for fine particulate pick-up,
like wallboard, concrete or surface dust.
DWV902L
This appliance can be used as industrial vacuum
cleaner and dust extractor for mobile operations to
take up all types of dry, non-combustible dusts up
to dust Class L with limit values for occupational
exposure greater than 1 mg/m³.
DWV902M
This appliance can be used as industrial vacuum
cleaner and dust extractor for mobile operations to
take up all types of dry, non-combustible dusts up
to dust Class M with limit values for occupational
exposure greater than or equal to 0.1 mg/m³.
DO NOT use in rain or in presence of flammable
liquids or gases.
These heavy-duty vacuums are for professional
use. DO NOT let children come into contact
with this appliance. Supervision is required when
inexperienced operators use this appliance.
DO NOT use the dust extractor for combustible
dust.
DO NOT use the dust extractor in explosive
atmospheres.
NOTE: This appliance is suited for the commercial
use, e.g. in hotels, schools, hospitals, factories,
shops, offices, rental companies, and on
construction sites.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
EWALT
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
WARNING: 115 V units have to
If the supply cord is damaged, it must be replaced
by D
prepared cord which is available through the
DEWALT service organisation.
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
EWALT service organisation by a specially
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
made to the earth terminal.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this appliance (see Technical Data).The
minimum conductor size is 1.5 mm2; the maximum
length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
(FIG. 1–3)
WARNING: To reduce the risk
of injury, turn appliance off and
disconnect appliance from power
source before installing and
removing accessories, before
adjusting or changing set-ups or
when making repairs. An accidental
start-up can cause injury.
27
Page 8
ENGLISH
WARNING: The filters (i) must always
1. If optional paper or fleece bag (t) is to be used,
NOTE: Be careful not to tear the bag. Place
2. Place the vacuum head (c) onto the canister
3. Insert end of hose (g) into twist-lock hose inlet (j)
be in place while vacuuming, except
as described under Wet Pick Up
Applications under Operation. When
vacuuming fine dust, you may also use
an additional paper bag or fleece bag to
make emptying the canister easier.
WARNING: Dust collection bags must
be used for dust Class M.
install as shown in figure 2.
bag securely onto inlet (j) to provide a tight seal
for maximum dust collection performance.
and secure it by closing the canister latches (d).
and rotate counterclockwise to lock in place.
OPERATION
Instructions for Use (fi g. 1, 4)
WARNING: Always observe the safety
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off/tool control switch (o) to the ON
3. Set the variable suction dial (n) to the desired
NOTE: This setting also controls the level of
4. Follow the direction under Connecting to
FLOW ALARM ADJUSTMENT (FIG. 4)
Class M models only
Adjust the flow alarm adjustment control (p) to
the correct hose (or tube) inside diameter size or
accessory diameter referring to the largest section.
The chosen diameter of the adjustment control must
instructions and applicable regulations.
WARNING: To reduce the risk
of injury, turn appliance off and
disconnect appliance from power
source before installing and
removing accessories, before
adjusting or changing set-ups or
when making repairs. An accidental
start-up can cause injury.
position ( ).
position. This feature allows the user to control
the vacuum's power, suction and noise.
suction. This is very useful in applications where
the vacuum creates unacceptable levels of drag
to the work piece.
Power Tools to connect to the power tool to
be used.
be equal or bigger as the largest diameter of the
used hose/tube/ accessories. The hose supplied is
32mm inside diameter. An acoustic alarm will sound
if the flow rate falls below 20 m/s. The system has a
time delay to reduce unintended alarms.
CONNECTING TO POWER TOOLS (FIG. 1, 4, 5)
WARNING: Only use the outlet (m) for
1. Plug the vacuum power cord into an
2. Plug the power tool into the outlet (m).
NOTE: See Power connection data of
3. Turn on/off/tool control switch (o) to the
NOTE: The vacuum cleaner starts automatically
4. To switch back to manual mode, turn the on/
5. Your D
NOTE: If using an adapter ensure it is firmly
a. Ensure the collar on the AirLock connector
b. Push the AirLock connector onto the adapter
c. Rotate the collar to the locked position.
NOTE: The ball bearings inside collar lock
purposes specified in the instructions.
appropriate outlet.
power tool under Technical Data for the
power allowance of the tool to be plugged into
the outlet (m).
ACTIVATION position . This allows the
vacuum to be turned on and off automatically
by the power tool.
within 0.5 seconds and continues to run for
15seconds after the power tool has been
turned off.
off/tool control switch (o) to the ON position ( ).
In manual mode the tool and the vacuum are
turned on and off independent of each other.
EWALT construction dust extractor is
fitted with the D
system. The AirLock allows for a fast, secure
connection between the suction hose (g) and
power tool. The AirLock connector (w) connects
directly to DEWALT compatable tools or through
the use of an AirLock adapter (available from
your local DEWALT supplier). Refer to the
Accessories section for detail on available
adapters.
attached to the tool outlet before following the
steps below.
is in the unlock position. Align notches (v) on
collar and AirLock connector as shown for
unlock and lock positions.
connector point.
into slot and secure the connection.The
power tool is now securely connected to the
dust extractor.
EWALT AirLock connection
28
Page 9
ENGLISH
AUTOMATIC FILTER CLEANING SYSTEM
This vacuum has a highly effective filter cleaning
system which minimizes filter clogging. Every
30seconds, one of the two filters gets automatically
cleaned. The cleaning process alternates between
the filters and continues through the life of the unit.
NOTE: It is normal to hear a clicking sound during
this process.
NOTE: After many hours of operation the automatic
filter cleaning system may not be effective. When
this happens the filters will need to be cleaned or
replaced. Refer to Filter under Maintenance.
PARKING BRAKE (FIG. 1, 6)
The parking brake will lock one wheel in place to
prevent vacuum from rolling.
1. To engage parking brake, depress
the brake button (x) to snap the brake into the
locked position.
2. To disengage parking brake, depress the brake
button and brake will snap into the unlocked
position.
REMOVE / CHANGE USED DUST COLLECTION BAG (FIG. 1)
1. Turn off vacuum and unplug cord from outlet.
2. Close the twist-lock hose inlet (j) with the inlet
3. Unlatch canister latches (d) and remove vacuum
4. Pull the collection bag carefully from inlet (j).
5. Seal the collection bag opening tightly when
6. Dispose of collection bag in appropriate
WET PICK UP APPLICATIONS (FIG. 1, 7)
WARNING: DO NOT connect power
WARNING: Plug vacuum into residual
WARNING: If foam or liquid escapes
WARNING: Appropriate personal
protective equipment like dust mask and
gloves should be used while handling
used dust bags.
plug (s).
head (c)
removing it from the machine.
container according to statutory provisions.
tools to outlet (m) when using the
vacuum for wet pick up.
current device (RCD) protected outlet
when using the vacuum for wet pick up.
from the machine, switch off
immediately.
CAUTION: Clean the water level limiting
device regularly and examine it for signs
of damage.
NOTICE: DO NOT remove ball float
Before using the vacuum for wet pick up:
TO EMPTY CANISTER (FIG. 1, 7)
The ball float valve (y) will block air to the motor
when the canister is full and the sound of the motor
will change at once. When the motor has a high
pitched sound and air/water flow stops, empty the
canister.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch canister latches (d) and remove vacuum
3. Empty contents of canister (f) into a suitable
TO CONVERT BACK TO DRY VACUUM OPERATION (FIG. 1)
1. Empty Canister, refer to To Empty Canister
2. Place canister upside down position until dry.
3. Place vacuum head (c) on a level surface until
4. Reinstall filters when vacuum head is dry. See
5. When canister is dry place the vacuum head (c)
TELESCOPING HANDLE (FIG. 1, 8)
Press release button (q) to raise and lower the
telescoping handle (r).
(y), doing so will cause damage to the
vacuum. The ball float keeps water from
entering the motor.
• Ensure the canister is empty and free of
excessive dust.
• Remove filters (i).
• Plug vacuum into a RCD protected outlet.
WARNING: Do not use the machine
with this set up for dust Class L and M.
head (c).
container or drain.
instructions.
DO NOT use wet canister for dry pick up.
dry.
Filters under Maintenance.
onto the canister and secure it by closing the
canister latches (d).
Shut Down/Transportation
(fi g. 1, 11)
1. Turn on/off/tool control switch (o) to the OFF
position.
2. Unplug the unit.
3. Class M only: Close the twist-lock hose inlet (j)
with the inlet plug (s).
4. Store the power cord (b) as shown.
5. When transporting in vehicles, secure the
machine.
29
Page 10
ENGLISH
MAINTENANCE
Your DEWALT appliance has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper appliance care and regular
cleaning.
WARNING: For user servicing, the
• The manufacturer, or an instructed
• When carrying out service or repair
• For Class M machines the
WARNING: To reduce the risk
of injury, turn appliance off and
disconnect appliance from power
source before installing and
removing accessories, before
adjusting or changing set-ups or
when making repairs. An accidental
start-up can cause injury.
machine must be dismantled, cleaned
and serviced, as far as is reasonably
practicable, without causing risk to the
maintenance staff and others. Suitable
precautions include, decontamination
before dismantling, provision for local
filtered exhaust ventilation where the
machine is dismantled, cleaning of the
maintenance area and suitable personal
protection.
person, shall perform a technical
inspection at least annually, consisting
of, for example, inspection of filters for
damage, air tightness of the machine
and proper function of the control
mechanism.
operations, all contaminated items
which cannot be satisfactorily cleaned,
are to be disposed of; such items
shall be disposed of in impervious
bags in accordance with any current
regulation for the disposal of such
waste.
outside of the machine should be
decontaminated by vacuum cleaning
methods and wiped clean or treated
with sealant before being taken
out of a hazardous area. All the
machine parts shall be regarded as
contaminated when removed from the
hazardous area and appropriate action
taken to prevent dust dispersal.
• For dust extractors it is necessary to
provide for an adequate air change
rate L in the room if the exhaust air is
returned to the room.
(NOTE: Reference to National
Regulations is necessary.)
Filter (fi g. 1, 9, 10)
FILTER CARE
The filters included with this vacuum are long life
filters. To be effective in minimizing dust recirculation,
the filters MUST be installed correctly and in good
condition.
WARNING: Appropriate personal
protective equipment like dust mask
and gloves should be used while
handling the filters.
To Remove Filters
1. Turn on/off/tool control switch (o) to the OFF
position (O) and unplug cord from outlet.
2. Release canister latches (d) and remove
vacuum head (c) from canister. Place vacuum
head on a level surface upside down.
3. Turn each filter (i) counterclockwise by gripping
it on the plastic end cover as shown, and
carefully remove from head, ensuring debris
does not fall into mounting hole.
NOTE: Use care to not damage filter material.
4 If the bottom side of the vacuum head (c) needs
to be cleaned, use a cloth dampened with
water and mild soap and allow it to dry. Dispose
of cloth in an appropriate container.
5. Inspect filters for wear, tears or other damage.
NOTE: If there is any doubt on the condition
of the filters they MUST be replaced. DO NOT
continue use if filters are damaged.
WARNING: Never use compressed
air or a brush to clean filters, otherwise
damage to the filter membrane will
occur which will allow dust to pass
through the filter. If needed, gently tap
against a hard surface or rinse with
room temperature water and let air
dry. Cleaning of the filters is typically
unnecessary, even if the filter is
covered with dust. The automatic filter
cleaning system will maintain maximum
performance and continue to function.
If visual damage to the filter membrane
exists, replace filters. Filters typically
last between six and twelve months
depending on use and care.
30
Page 11
ENGLISH
To Install Filters
1. Ensure filter seal (aa) is in place and is secure
2. Line up filter threads (z) to vacuum head threads
and using moderate force, turn filter clockwise
until tight.
NOTE: Use care to not damage filter material.
3. Place the vacuum head (c) onto the container
and secure it by closing the canister latches (d).
Lubrication
Your appliance requires no additional lubrication.
Cleaning
WARNING: Never use solvents or other
harsh chemicals for cleaning the nonmetallic parts of the appliance. These
chemicals may weaken the materials
used in these parts. Never let any liquid
get inside the machine; never immerse
any part of the appliance into a liquid.
1. Vacuum the outside of the dust extractor. For
further cleaning use a cloth dampened only with
water and mild soap if necessary.
2. After use dispose of cloth in an appropriate
container.
Storage (fi g. 11)
1. Empty the canister, refer to To Empty Canister
under Operation.
2. Clean the vacuum inside and outside. Refer to
Cleaning.
3. Clean or replace filters, refer to Filters.
4. Store the suction hose and the power cord as
shown in the illustration. Place the unit in a dry
room and secure it from unauthorized use.
NOTE: Plug inlet plug (s) into inlet (j) to keep
debris inside canister when suction hose is
removed. You can also attach the ends of the
hose together and lock together with the twistlock end.
Optional Accessories
WARNING: Since accessories, other
SECURING THE POWER CORD TO THE HOSE (FIG. 1)
The power cord (b) can be secured to the suction
hose (g) using the D279058CL hose clip (available
from your local D
Consult your dealer for further information on the
appropriate accessories.
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this appliance
could be hazardous. To reduce the risk
of injury, only D
accessories should be used with this
product.
ACCESSORIES
DWV9310-XJ Filter
DWV9315-XJ Crush-proof hose
DWV9316-XJ Anti-static hose
DWV9401-XJ Paper bag
DWV9400-XJ Plastic liner
DWV9402-XJ Fleece bag
D
EWALT AirLock System
DWV9000 Twist-Lock
DWV9110 29-35mm tapered
DWV9120 35-38mm stepped
DWV9130 35mm OD adapter
DWV9150 35mm OD angle
EWALT supplier).
EWALT recommended
connection
rubber adapter
rubber adapter
adapter
Troubleshooting
PROBLEM SOLUTION
Motor
does not
run
Suction
capacity
decreases
Check power cord, plugs and outlet.
Ensure the on/off /tool control switch
is in the ON position ( ).
Remove blockages in the suction
nozzle, suction tube, suction hose
or filters.
Replace the paper or fleece bag.
Check for proper installation of the
filters.
Clean or replace the filters.
Empty canister, refer to Empty
Canister under Operation.
31
Page 12
ENGLISH
PROBLEM SOLUTION
Vacuum
stops
running
Dust
comes
out while
vacuuming
Automatic
filter
cleaning
is not
working
Power tool
does not
turn on.
Thermal overload has been tripped:
1. Turn the vacuum off and
disconnect vacuum cleaner from
power source.
2. Empty the canister, if needed.
3. Allow the unit to cool.
4. Plug the power cord into an
appropriate outlet and turn on/
off/tool control switch to the ON
position (
not restart contact your seller or
check the location of your nearest
authorised DEWALT repair agent
in the DEWALT catalogue or
contact your DEWALT office at the
address indicated in this manual.
Check for proper installation of the
filters.
Ensure filters are not damaged;
replace if necessary.
Ensure filter seals are in place and are
secure.
Listen for the solenoid clicking to
ensure the filter cleaning mechanism
is working.
Ensure the on/off/tool control switch is
in the ACTIVATION position
) to test. If vacuum will
.
D
EWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
EWALT office at the address indicated in this
D
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
32
Page 13
GUARANTEE
DEWALT is confident of the quality of its
products and offers an outstanding guarantee
for professional users of the product. This
guarantee statement is in addition to and in
no way prejudices your contractual rights as a
professional user or your statutory rights as a
private non-professional user. The guarantee
is valid within the territories of the Member
States of the European Union and the
European Free Trade Area.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your D
simply return it within 30 days, complete
with all original components, as purchased,
to the point of purchase, for a full refund
or exchange. The product must have been
subject to fair wear and tear and proof of
purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
EWALT product, in the 12 months following
D
purchase, you are entitled to one service free
of charge. It will be undertaken free of charge
at an authorised DEWALT repair agent. Proof
of purchase must be produced. Includes
labour. Excludes accessories and spare parts
unless failed under warranty.
• ONE YEAR FULL WARRANTY •
EWALT product becomes defective
If your D
due to faulty materials or workmanship
within 12 months from the date of purchase,
DEWALT guarantees to replace all defective
parts free of charge or – at our discretion –
replace the unit free of charge provided that:
• The product has not been misused;
• The product has been subject to fair
wear and tear;
• Repairs have not been attempted by
unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all
original components.
If you wish to make a claim, contact your
seller or check the location of your nearest
authorised DEWALT repair agent in the
D
EWALT catalogue or contact your DEWALT
office at the address indicated in this manual.
A list of authorised D
full details of our after-sales service is available
on the Internet at: www.2helpU.com.
EWALT product,
EWALT repair agents and
ENGLISH
33
Loading...