DeWalt DW368, DW367, DW369 User Manual
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DW367, DW368, DW369
7-1/4"(184 mm) Circular Saws
Scies circulaires de 184 mm (7 1/2 po)
Sierras circular de 184 mm (7-1/4")
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(JAN06) Form No. 638619-00 DW367, DW368, DW369
Copyright © 2002, 2003, 2004, 2005, 2006 D
EWALT
The following are trademarks for one or more D
EWALT power tools: the yellow and black color scheme;
the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the
array of lozenge-shaped humps on the surface of the tool.
GENERAL SAFETY INSTRUCTIONS
WARNING! Read and understand all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-
dents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust
or fumes.
• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Grounded tools must be plugged into an outlet properly installed and grounded in
accordance with all codes and ordinances. Never remove the grounding prong or
modify the plug in any way. Do not use any adapter plugs. Check with a qualified
electrician if you are in doubt as to whether the outlet is properly grounded. If the
tools should electrically malfunction or break down, grounding provides a low resistance
path to carry electricity away from the user. Applicable only to Class I (grounded) tools.
• Double insulated tools are equipped with a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insu-
lation eliminates the need for the three wire grounded power cord and grounded power
supply system. Applicable only to Class II (double insulated) tools. The DW367,
DW368 and DW369 are double insulated tools.
• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
• Don’t expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from
an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
• When operating a power tool outside, use an outdoor extension cord marked “WA” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more AWG
Than Than
12 16 14 12 Not Recommended
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury,
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts. Air vents often cover moving parts and should also be
avoided.
• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key
that is left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk
of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on
another tool.
SERVICE
• Tool service must be performed only by qualified repair personnel. Service or main-
tenance performed by unqualified personnel could result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in
the maintenance section of this manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock or injury.
Additional Safety Instructions for Circular Saws
DANGER! Keep hands away from cutting area and blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut
by the blade.
CAUTION: Blades coast after turn off.
• Keep your body positioned to either side of the blade, but not in line with the saw
blade. KICKBACK could cause the saw to jump backwards (see Causes and Operator
Prevention of Kickback and KICKBACK).
• Do not reach underneath the work. The guard can not protect you from the blade below
the work.
• Check lower guard for proper closing before each use. Do not operate saw if lower
guard does not move freely and close instantly. Never clamp or tie the lower guard
into the open position. If saw is accidentally dropped, the lower guard may be bent. Raise
the lower guard with the retracting handle and make sure it moves freely and does not
touch the blade or any other part, at all angles and depth of cut.
• Check the operation and condition of the lower guard spring. If the guard and the
spring are not operating properly, they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
• Lower guard should be retracted manually only for special cuts such as “pocket
cuts” and “compound cuts.” Raise lower guard by retracting handle. As soon as
blade enters the material, lower guard must be released. For all other sawing, the lower
guard should be allowed to operate automatically.
• Always observe that the lower guard is covering the blade before placing saw down
on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards,
cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch
is released.
• NEVER hold piece being cut in your hands or across your leg. It is important to sup-
port the work properly to minimize body exposure, blade binding, or loss of control.
• Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will
also make exposed metal parts of the tool “live” and shock the operator.
• When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance for blade binding.
• Always use blades with correct size and shape (diamond vs. round) arbor holes.
Blades that do not match the mounting hardware of the saw will run eccentrically, causing
loss of control.
• Never use damaged or incorrect blade washers or bolts. The blade washers and bolt
were specially designed for your saw, for optimum performance and safety of operation.
• Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.
• Do not operate this tool for long periods of time. Vibration caused by the operating
action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to
provide extra cushion, take frequent rest periods, and limit daily time of use.
CAUSES AND OPERATOR PREVENTION OF KICKBACK
• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the workpiece toward the operator.
• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly back toward the operator.
• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the
blade can dig into the top surface of the wood causing the blade to climb out of the kerf and
jump back toward operator.
• Kickback is the result of tool misuse and/or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as given below:
• Maintain a firm grip with both hands on the saw and position your body and arm to
allow you to resist kickback forces. Kickback forces can be controlled by the operator, if
proper precautions are taken.
• When blade is binding, or when interrupting a cut for any reason, release the trigger
and hold the saw motionless in the material until the blade comes to a complete stop.
Never attempt to remove the saw from the work or pull the saw backward while the
blade is in motion or kickback may occur. Investigate and take corrective actions to elim-
inate the cause of blade binding.
• When restarting a saw in the workpiece, center the saw blade in the kerf and check
that the saw teeth are not engaged into the material. If saw blade is binding, it may walk
up or kickback from the workpiece as the saw is restarted.
• Support large panels to minimize the risk of blade pinching and kickback. Large pan-
els tend to sag under their own weight. Support must be placed under the panel on both
sides, near the line of cut and near the edge of the panel.
• Do not use dull or damaged blade. Unsharpened or improperly set blades produce nar-
row kerf causing excessive friction, blade binding, and kickback.
• Blade depth and bevel adjusting locking levers must be tight and secure before mak-
ing cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.
• Use extra caution when making a “Pocket Cut” into existing walls or other blind
areas. The protruding blade may cut objects that can cause kickback.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA repiratory protection.
CAUTION: When cutting into walls, floors or wherever live electrical wires may be encoun-
tered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated
grasping surfaces to prevent electric shock if you cut into a live wire.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V ................volts A ......................amperes
Hz ..............hertz W ......................watts
min ............minutes ....................alternating current
..........direct current no......................no load speed
..............Class II Construction …/min ..............revolutions per minute
..............earthing terminal ....................safety alert symbol
FEATURES
A. End cap D. Shoe
B. Trigger switch E. Blade clamping screw
C. Bevel angle adjustment F. Lower blade guard
Motor
Your DEWALT tool is powered by a DEWALT motor. Be sure
your power supply agrees with nameplate marking. 120
Volts AC/DC means your saw will operate on alternating or
direct current. As little as 10% lower voltage can cause loss
of power and can result in overheating. All D
EWALT tools
are factory-tested; if this tool does not operate, check the
power supply.
Changing Blades
CAUTION: ALWAYS TURN OFF AND DISCONNECT TOOL BEFORE CHANGING
ACCESSORIES OR MAKING ANY ADJUSTMENTS.
B
C
A
D
E
F
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-DEWALT • www.dewalt.com
TO INSTALL THE BLADE (FIG. 1–4)
1. Place inner clamp washer (G) on saw spindle with the large flat surface facing out toward
the blade.
2. Retract the lower blade guard (F) and place blade on saw spindle against the inner clamp
washer, making sure that the blade will rotate in the proper direction (the direction of the
rotation arrow on the saw blade and the teeth must point in the same direction as the direction of rotation arrow on the saw). Do not assume that the printing on the blade will always
be facing you when properly installed. When retracting the lower blade guard to install the
blade, check the condition and operation of the lower blade guard to assure that it is working properly. Make sure it moves freely and does not touch the blade or any other part, in
all angles and depths of cut.
3. Place outer clamp washer (H) on saw spindle with the large flat surface against the blade
and the wording on the outer clamp washer facing you.
4. Thread blade clamping screw (E) into saw spindle by hand (screw has right-hand threads
and must be turned clockwise to tighten).
5. Depress the blade lock (I) while turning the saw spindle with the blade wrench until the
blade lock engages and the blade stops rotating.
6. Tighten the blade clamping screw firmly with the blade wrench.
NOTE: Never engage the blade lock while saw is running, or engage in an effort to stop the tool.
Never turn the saw on while the blade lock is engaged. Serious damage to your saw will result.
TO REPLACE THE BLADE
1. To loosen the blade clamping screw (E), depress the blade lock (I) and turn the saw spindle with the blade wrench until the blade lock engages and the blade stops rotating. With
the blade lock engaged, turn the blade clamping screw clockwise with the blade wrench
(screw has right-hand threads and must be turned counterclockwise to loosen).
2. Remove the blade clamping screw (E) and outer clamp washer (H) only. Remove old
blade.
3. Clean any sawdust that may have accumulated in the guard or clamp washer area and
check the condition and operation of the lower blade guard as previously outlined. Do not
lubricate this area.
4. Select the proper blade for the application (see Blades). Always use blades that are the
correct size (diameter) with the proper size and shape center hole for mounting on the saw
spindle. Always assure that the maximum recommended speed (rpm) on the saw blade
meets or exceeds the speed (rpm) of the saw.
5. Follow steps 2 through 6 under To Install the Blade, making sure that the blade will rotate
in the proper direction.
LOWER BLADE GUARD
WARNING: The lower blade guard is a safety feature which reduces the risk of serious
personal injury. Never use the saw if the lower guard is missing, damaged, misassembled or not working properly. Do not rely on the lower blade guard to protect you under
all circumstances. Your safety depends on following all warnings and precautions as
well as proper operation of the saw. Check lower guard for proper closing before each
use as outlined in Additional Safety Rules for Circular Saws. If the lower blade guard is
missing or not working properly, have the saw serviced before using. To assure product safety and reliability, repair, maintenance and adjustment should be performed by
an authorized service center or other qualified service organization, always using identical replacement parts.
Cutting Depth Adjustment (Fig. 5, 6)
CAUTION: ALWAYS TURN OFF AND DISCONNECT TOOL BEFORE CHANGING
ACCESSORIES OR MAKING ANY ADJUSTMENTS.
1. Hold the saw firmly. Raise the depth adjustment lever (J) to loosen and move shoe to
obtain the desired depth of cut, as shown. Make sure the depth adjustment lever has been
retightened (lowered) before operating the saw.
2. Your saw is equipped with a carbide tipped saw blade for long life and efficient cutting.
3. Setting the saw at the proper cutting depth keeps blade friction to a minimum, removes
sawdust from between the blade teeth, results in cooler, faster sawing and reduces the
chance of kickback. Align the appropriate mark on the depth adjustment strap with triangle
on the upper blade guard (K). Your depth is set.
4. For the most efficient cutting action using a carbide tipped saw blade, set the depth adjustment so that about one half of a tooth projects below the surface of the wood to be cut.
5. A method of checking for the correct cutting depth is shown in Figure 6. Lay a piece of the
material you plan to cut along the side of the blade, as shown in the figure, and observe
how much tooth projects beyond the material.
Bevel Angle Adjustment (Fig. 7, 8)
CAUTION: ALWAYS TURN OFF AND DISCONNECT TOOL BEFORE CHANGING
ACCESSORIES OR MAKING ANY ADJUSTMENTS.
The full range of bevel adjustment on the DW367 is 0 to 50 degrees. The pivot bracket is
graduated in 5 degree increments.
On the DW368 and DW369, the full range of bevel adjustment is 0 to 56 degrees. The pivot
bracket is graduated in increments of 1 degree.
There is a bevel angle adjustment mechanism (M) consisting of a quadrant with a pointer (N)
and a lever (L) on the front of the saw.
1. To set the saw for a bevel cut, raise the lever (L) or turn the knob (O) to loosen the bevel
adjustment.
2. Tilt the shoe to the desired angle by aligning the pointer with the desired angle mark on the
pivot bracket.
3. Retighten the bevel adjustment by lowering the lever or turning the knob.
Bevel Detent (Fig. 7, 8)
CAUTION: ALWAYS TURN OFF AND DISCONNECT TOOL BEFORE CHANGING
ACCESSORIES OR MAKING ANY ADJUSTMENTS.
The DW367 has a bevel stop at 45 degrees. To set the bevel at an angle greater than
45 degrees, tilt the shoe to 45 degrees, then slide the knob and bolt into the upper slot. When
you reach the desired angle, tighten the knob.
The DW368 and DW369 are equipped with a bevel detent feature. As you tilt the shoe you will
hear a click and feel the shoe stop at both 22.5 and 45 degrees. If either of these is the desired
angle, retighten the lever (L) by lowering it. If you desire another angle, continue tilting the shoe
until the pointer aligns with the desired mark.
Kerf Indicator (Figure 9)
The front of the saw shoe has a kerf indicator for vertical and bevel cutting. This indicator
enables you to guide the saw along cutting lines penciled on the material being cut. The
indicator lines up with the left (inner) side of the saw blade, which makes the slot or "kerf" cut
by the moving blade fall to the right of the indicator. The ribs on the front of the DW368
and DW369 shoe are at 1/4" (6.35 mm) spacing. The notches on the front of the shoe are at
1/2" (13 mm) intervals.
OPERATION
Switch (Fig. 1)
Pull the trigger switch (B) to turn the motor on. Releasing the trigger turns the motor off. This
tool has no provision to lock the switch in the on position, and the tool should never be locked
on in any way.
Workpiece Support
Figure 10 and 12 show proper sawing position. Figure 11 and 13 show an unsafe condition.
Hands should be kept away from cutting area, and power cord is positioned clear of the cutting area so that it will not get caught or hung up on the work.
To avoid kickback, DO support board or panel NEAR the cut, (Fig. 10 and 12). DON’T support
board or panel away from the cut (Fig. 11 and 13). When operating the saw, keep the cord
away from the cutting area and prevent it from becoming hung up on the work piece.
WARNING: It is important to support the work properly and to hold the saw firmly to pre-
vent loss of control which could cause personal injury; Figure 12 illustrates typical hand support of the saw.
ALWAYS DISCONNECT SAW BEFORE MAKING ANY ADJUSTMENTS! Place the work with
its “good” side - the one on which appearance is most important - down. The saw cuts upward,
so any splintering will be on the work face that is up when you saw it.
Cutting
Support the work so that the waste will be on your right. Place the wider portion of the saw
shoe on that part of the work piece which is solidly supported, not on the section that will fall
off when the cut is made. As examples, Figure 12 illustrates the RIGHT way to cut off the end
of a board, and Figure 13 the WRONG way. Always clamp work. Don’t try to hold short pieces
by hand! Remember to support cantilevered and overhanging material. Use caution when
sawing material from below.
Be sure that the saw is up to full speed before blade contacts material to be cut. Starting the
saw with blade against material to be cut or pushed forward into kerf can result in kickback.
Push the saw forward at a speed which allows the blade to cut without laboring. Hardness and
toughness can vary even in the same piece of material, and knotty or damp sections can put
a heavy load on the saw. When this happens, push the saw more slowly, but hard enough to
keep it working without much decrease in speed.
Kickback
When the saw blade becomes pinched or twisted in the cut, kickback can occur. The saw is
thrust rapidly back toward the operator. When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction drives the unit backward. When the blade
becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into
the top surface of the wood causing the blade to climb out of the kerf and jump back toward
the operator.
Kickback is more likely to occur when any of the following conditions exist.
1. IMPROPER WORKPIECE SUPPORT
A. Sagging or improper lifting of the cut off piece can cause pinching of the blade and lead
to kickback. (Figure 11)
B. Cutting through material supported at the outer ends only can cause kickback. As the
material weakens it sags, closing down the kerf and pinching the blade.
C. Cutting off a cantilevered or overhanging piece of material from the bottom up in a
vertical direction can cause kickback. The falling cut off piece can pinch the blade.
D. Cutting off long narrow strips (as in ripping) can cause kickback. The cut off strip can
sag or twist closing the kerf and pinching the blade.
E. Snagging the lower guard on a surface below the material being cut momentarily
reduces operator control. The saw can lift partially out of the cut increasing the chance
of blade twist.
2. IMPROPER DEPTH OF CUT SETTING ON SAW
To make the most efficient cut, the blade should protrude only far enough to expose
1/2 of a tooth as shown in figure 5. This allows the shoe to support the blade and
minimizes twisting and pinching in the material. See the section titled Cutting Depth
Adjustment.
3. BLADE TWISTING (MISALIGNMENT IN CUT)
A. Pushing harder to cut through a knot, a nail, or a hard grain area can cause the blade
to twist.
B. Trying to turn the saw in the cut (trying to get back on the marked line) can cause blade
twist.
C. Over-reaching or operating the saw with poor body control (out of balance), can result
in twisting the blade.
D. Changing hand grip or body position while cutting can result in blade twist.
E. Backing up the saw to clear blade can lead to twist if it is not done carefully.
4. MATERIALS THAT REQUIRE EXTRA ATTENTION
A. Wet lumber
B. Green lumber (material freshly cut or not kiln dried)
C.Pressure treated lumber (material treated with preservatives or anti-rot chemicals)
5. USE OF DULL OR DIRTY BLADES
Dull blades cause increased loading of the saw. To compensate, an operator will usually
push harder which further loads the unit and promotes twisting of the blade in the kerf.
Worn blades may also have insufficient body clearance which increases the chance of
binding and increased loading.
6. LIFTING THE SAW WHEN MAKING BEVEL CUTS
Bevel cuts require special operator attention to proper cutting techniques – especially
guidance of the saw. Both blade angle to the shoe and greater blade surface in the material increase the chance for binding and misalignment (twist) to occur.
7. RESTARTING A CUT WITH THE BLADE TEETH JAMMED AGAINST THE MATERIAL
The saw should be brought up to full operating speed before starting a cut or restarting a
cut after the unit has been stopped with the blade in the kerf. Failure to do so can cause
stalling and kickback.
Any other conditions which could result in pinching, binding, twisting, or misalignment of the
blade could cause kickback. Refer to Additional Safety Instructions and Operation for
procedures and techniques that will minimize the occurrence of kickback.
MAINTENANCE
Cleaning
Use only mild soap and a damp cloth to clean the tool. Many household cleaners contain
chemicals which could seriously damage plastic. Do not use gasoline, turpentine, lacquer or
paint thinner, dry cleaning fluids or similar products. Never let any liquid get inside the tool;
never immerse any part of the tool in a liquid.
Lubrication
Self lubricating ball and roller bearings are used in the tool and relubrication is not required.
However, it is recommended that, once a year, you take or send the tool to a service center
for a thorough cleaning, inspection and lubrication of the gear case.
FIG. 1
FIG. 2
FIG. 3
FIG. 5
FIG. 6
FIG. 4
J
LOOSEN
TIGHTEN
DW369
J
K
DW367, DW368
DW367
FIG. 11
FIG. 12
FIG. 13
FIG. 10
I
FIG. 14
G
E
H
FIG. 8
FIG. 9
0˚
45˚
1/4”
6.35 mm
1/2”
13 mm
FIG. 7
L
M
O
TIGHTEN
LOOSEN
N
SI VOUS AVEZ DES QUESTIONS OU VOUS VOULEZ NOUS FAIRE PART DE VOS COMMENTAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL DEWALT, COMPOSEZ
SANS FRAIS LE : 1 800 433-9258.
Règles de sécurité – Généralités
AVERTISSEMENT! Lire et comprendre toutes les directives, car le nonrespect des directives suivantes peut entraîner un choc électrique, un incendie
ou des blessures graves.
CONSERVER CES DIRECTIVES
ZONE DE TRAVAIL
• Garder la zone de travail propre et bien éclairée; les établis encombrés et les endroits
sombres sont propices aux accidents.
• Ne pas utiliser les outils électriques dans une atmosphère explosive, comme à proximité de liquides, de gaz ou de poussières inflammables; le moteur peut créer des étin-
celles et enflammer les vapeurs ou les poussières environnantes.
Electric Brake (DW369 Only)
Your saw has an automatic electric brake which is designed to stop the blade from coasting
in about two seconds, after you release the trigger switch. It is useful when making certain
cuts in wood where a coasting blade would result in a wide, imprecise cut.
Occasionally, the brake will not function properly and won’t stop the saw in the 2 seconds
discussed above. If this condition persists, turn the saw on and off four or five times. If the
brake still does not stop the blade in about 2 seconds, the problem may be worn brushes.
Replace the brushes as described below and try the saw again. If the problem still persists,
have the tool serviced at a D
EWALT certified service center.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
performed by a D
EWALT factory service center, a DEWALT authorized service center or other
qualified service personnel. Always use identical replacement parts. (Refer to Brushes for
brush replacement information.)
Brushes
CAUTION: ALWAYS TURN OFF AND DISCONNECT TOOL BEFORE CHANGING
ACCESSORIES OR MAKING ANY ADJUSTMENTS.
Inspect carbon brushes regularly by unplugging tool, removing the end cap and withdrawing
the brush assembly. Keep brushes clean and sliding freely in their guides. Always replace a
used brush in the same orientation in the holder as it was prior to removal. Carbon brushes
have varying symbols stamped into their sides, and if either brush is worn down to the line
closest to the spring, the brushes must be replaced. Use only identical D
EWALT brushes. New
brush assemblies are available at your local service center. Always replace the end cap after
inspecting or servicing brushes. The tool should be allowed to “run in” (run at no load without
a blade) for 5 minutes before use to seat new brushes.
While “running in” DO NOT TIE, TAPE, OR OTHERWISE LOCK THE TRIGGER SWITCH ON.
HOLD BY HAND ONLY.
Shoe Adjustment
CAUTION: ALWAYS TURN OFF AND DISCONNECT TOOL BEFORE CHANGING
ACCESSORIES OR MAKING ANY ADJUSTMENTS.
Your shoe has been factory set to assure that the blade is perpendicular to the shoe. If after
extended use, you need to re-align the blade follow the directions below:
ADJUSTING FOR 90 DEGREE CUTS
1. Return the saw to 0 degrees bevel.
2. Place the saw on its side, and retract the lower guard.
3. Loosen the bevel adjustment lever (L). Place a square against the blade and the shoe as
shown in figure 14.
4. Using a hex wrench, turn the set screw on the underside of the shoe until the blade and
the shoe are both in flush contact with the square. Retighten the bevel adjustment lever.
ADJUSTING BEVEL ADJUSTMENT AND DEPTH ADJUSTMENT LEVERS
It may be desirable to adjust the depth adjustment lever or the bevel adjustment lever. They
may loosen in time and hit the shoe before tightening. To tighten the levers, follow the steps
below.
ADJUSTING THE BEVEL ADJUSTMENT LEVER (DW368, DW369)
NOTE: The following instructions also apply to adjusting the DW367 and DW368 depth
adjustment lever.
1. Using a small screwdriver, pry the lock ring off.
2. Remove the lever and rotate it in the desired direction about 1/8 of a revolution.
3. Reinstall the lock ring with the concave side against the lever.
ADJUSTING DEPTH ADJUSTMENT LEVER (DW369 ONLY)
1. Loosen the screw securing the depth adjustment lever.
2. Remove the depth adjustment lever and rotate it to the desired location, about 1/8 of a
revolution.
3. Tighten the lever screw.
Blades
A dull blade will cause inefficient cutting, overload on the saw motor, excessive splintering and
increase the possibility of kickback. Change blades when it is no longer easy to push the saw
through the cut, when the motor is straining, or when excessive heat is built up in the blade.
It is a good practice to keep extra blades on hand so that sharp blades are available for immediate use. Dull blades can be sharpened in most areas; see SAWS-SHARPENING in the yellow pages.
Hardened gum on the blade can be removed with kerosene, turpentine, or oven cleaner. Antistick coated blades can be used in applications where excessive build-up is encountered, such
as pressure treated and green lumber.
ACCESSORIES
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center.
CAUTION: The use of any non-recommended accessory may be hazardous.
DO NOT USE WATER FEED ATTACHMENTS WITH THIS SAW.
VISUALLY EXAMINE CARBIDE BLADES BEFORE USE. REPLACE IF DAMAGED.
RECOMMENDED BLADE TYPES
COMBINATION FRAMING - 5/8" Round arbor, 24 teeth
All purpose fast rip and cross cuts.
PRESSURE TREATED/WET LUMBER - 5/8" Round arbor, 20 teeth
Coated - Resistant to gum build-up
EXTREME DURABILITY - 5/8" Round arbor, 18 teeth
Coated, rock carbide
FINISHING - 5/8" Round arbor, 36 teeth
More teeth for finer finish cuts.
FAST CUT FRAMING - 5/8" Round arbor, 16 teeth
Fastest blade for rips and cross cuts
If you need assistance in locating any accessory for your tool, please contact DEWALT
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
EWALT (1-800-
433-9258) or visit our website www.dewalt.com.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
EWALT (1-800-433-9258). This warranty does not apply
to accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, D
EWALT tools are covered by our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
EWALT Power Tool, Laser,
or Nailer for any reason, you can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.
• Tenir les enfants, les visiteurs ou toute autre personne éloignés lorsqu’on utilise un
outil électrique; les distractions peuvent faire perdre la maîtrise de ce dernier.
MESURES DE SÉCURITÉ - ÉLECTRICITÉ
• Les outils mis à la terre doivent être branchés dans une prise bien installée et mise
à la terre conformément à tous les codes et règlements en vigueur. Ne jamais retirer
la broche de terre ni modifier la fiche. Ne pas utiliser d'adaptateur. Vérifier auprès d'un électricien qualifié en cas de doute quant à la mise à la terre de la prise. En cas de défaillance
électrique ou de bris de l'outil, la mise à la terre procure un chemin de faible résistance au
courant qui autrement traverserait l'utilisateur. Cette protection ne s’applique qu’aux out-
ils de classe I (mis à la terre).
• Les outils à double isolation sont munis d’une fiche polarisée (c’est-à-dire que l’une
des lames est plus large que l’autre), laquelle ne peut être raccordée qu’à une prise
polarisée et ce, dans un seul sens; on doit l’inverser si on est incapable de l’enfoncer complètement. Si la fiche ne s’adapte toujours pas, on doit demander à un électricien qualifié d’installer la prise appropriée. On ne doit jamais modifier la fiche. La dou-
ble isolation élimine le besoin d’installer un cordon d’alimentation trifilaire et un système
d’alimentation électrique pourvus d’une mise à la terre; seuls les outils de classe II (à double isolation) sont munis d’une telle protection. Les modèles DW367, DW368 et DW369
sont des outils à double isolation.
• Éviter tout contact entre le corps et les éléments mis à la terre, comme les tuyaux,
les radiateurs, les cuisinières et les réfrigérateurs, afin de réduire les risques de choc
électrique.
• Ne pas utiliser l’outil électrique dans des endroits mouillés, ni l’exposer à la pluie;
l’infiltration d’eau à l’intérieur de l’outil augmente les risques de choc électrique.
• Ne pas utiliser le cordon de manière abusive; on ne doit pas transporter l’outil en le
tenant par le cordon, ou utiliser ce dernier pour le débrancher. On doit tenir le cordon
éloigné des sources de chaleur, de l’huile, des bords tranchants ou des pièces mobiles.
Remplacer immédiatement les cordons endommagés, car ces derniers augmentent les
risques de choc électrique.
• Lorsqu’on utilise un outil électrique à l’extérieur, on ne doit utiliser que des rallonges
conçues pour cet usage, comme celles de type « W-A » ou « W », afin de réduire les
risques de choc électrique. S’assurer que la rallonge est en mesure de porter le courant
nécessaire à l’outil. Une rallonge de calibre inférieur entraînera une chute de tension se
traduisant par une perte de puissance et une surchauffe. Le tableau ci-dessous illustre les
calibres que l’on doit utiliser selon la longueur de la rallonge et l’intensité nominale indiquée
sur la plaque signalétique. En cas de doute, utiliser le calibre suivant. Plus le calibre est
petit, plus la rallonge peut porter du courant.
Calibre minimal des cordons de rallonge
Tension Longueur totale du cordon en meters
120 V De 0 à 7 De 7 à 15 De 15 à 30 De 30 à 45
240 V De 0 à 7 De 7 à 15 De 15 à 39 De 30 à 45
Intensité (A)
Au Au Calibre moyen de fil
moins plus
12 - 16 14 12 Non recommandé
SÉCURITÉ PERSONNELLE
• Rester vigilant en tout temps et faire preuve de jugement lorsqu’on utilise un outil
électrique; ne pas utiliser l’outil lorsqu’on est fatigué ou sous l’influence de drogues, d’al-
cool ou de médicaments, car un moment d’inattention peut entraîner des blessures graves.
• Porter des vêtements appropriés; ne pas porter de vêtements amples, de gants ni
de bijoux, et couvrir ou attacher les cheveux longs, car ceux-ci peuvent rester coincés
dans les pièces mobiles. Se tenir éloigné des évents puisque ces derniers pourraient camoufler des pièces mobiles.
• Éviter les démarrages accidentels; s’assurer que l’interrupteur soit en position d’arrêt
avant de brancher l’outil. Ne pas transporter l’outil en laissant le doigt sur l’interrupteur ni
le brancher lorsque l’interrupteur est en position de marche, car cela pourrait causer un
accident.
• Retirer les clés de réglage avant de démarrer l’outil; une clé laissée sur une pièce rotative peut entraîner des blessures.
• Ne pas trop étendre les bras; les pieds doivent rester ancrés fermement au sol afin de
maintenir son équilibre en tout temps et de mieux maîtriser l’outil dans des situations
imprévues.
• Utiliser le matériel de sécurité approprié; toujours porter des lunettes de protection.
Porter un masque anti-poussières, des chaussures antidérapantes, un casque de sécurité
ou des protecteurs auditifs lorsque la situation le requiert.
UTILISATION ET ENTRETIEN DE L’OUTIL
• Fixer et soutenir la pièce sur une plate-forme stable au moyen d’une butée fixe ou
de tout autre dispositif semblable; la pièce est instable lorsqu’on la retient manuelle-
ment ou qu’on l’appuie contre le corps, ce qui peut faire perdre la maîtrise de l’outil.
• Ne pas forcer l’outil ni l’utiliser pour des travaux autres que ceux pour lesquels il a
été conçu. Pour obtenir de meilleurs résultats et prévenir les risques de blessure, laisser
l’outil couper à la vitesse pour laquelle il a été conçu.
• Ne pas utiliser l’outil lorsque l’interrupteur marche-arrêt ne fonctionne pas; tout outil
qui ne peut être commandé au moyen de l’interrupteur est dangereux et doit être réparé.
• Débrancher l’outil avant d’effectuer un réglage, de changer les accessoires ou de
ranger l’outil; ces mesures de sécurité préventives réduisent les risques de démarrage
accidentel.
• Lorsqu’on n’utilise pas l’outil, le ranger hors de la portée des enfants ou des
personnes non qualifiées; les outils sont dangereux entre les mains de personnes inex-
périmentées.
• Bien entretenir l’outil et s’assurer qu’il soit toujours bien propre et aiguisé; les outils bien entretenus et dont les bords sont bien tranchants sont moins susceptibles de rester
coincés et sont plus faciles à maîtriser.
• Vérifier les pièces mobiles afin de s’assurer qu’elles soient bien alignées et qu’elles
ne restent pas coincées; vérifier également les pièces afin de s’assurer qu’il n’y ait ni bris
ni aucune autre condition susceptible de nuire au bon fonctionnement de l’outil; faire
réparer l’outil si ce dernier est endommagé avant de s’en servir à nouveau, car les accidents sont souvent causés par des outils mal entretenus.
• N’utiliser que les accessoires recommandés par le fabricant pour le modèle en
question; un accessoire destiné à un outil particulier peut devenir dangereux lorsqu’il est
utilisé avec un autre.
ENTRETIEN
• L’outil doit être entretenu par le personnel qualifié seulement; toute maintenance
effectuée par une personne non qualifiée peut entraîner des risques de blessure.
• Lors de l’entretien, n’utiliser que des pièces de rechange identiques et suivre les
directives de la section «Entretien» du présent manuel afin de prévenir les risques de
choc électrique ou de blessure.
Règles de sécurité additionnelles concernant
les scies circulaires
DANGER! Garder les mains éloignées des zones de coupe et de la lame. Toujours tenir
l’outil en plaçant une main sur la poignée auxiliaire ou le carter du moteur; on protège ses
mains en les utilisant toutes les deux pour tenir l’outil.
MISE EN GARDE : les lames ne s’arrêtent pas immédiatement lorsque l’interrupteur est
mis en position d’arrêt.
• Toujours se placer d’un côté ou de l’autre de la lame en évitant de se tenir dans son
trajet, car la scie pourrait reculer brusquement par suite d’un REBOND. (Voir les sections
« Causes du rebond et mesures préventives » et « Effet de rebond ».
• Ne pas mettre les mains sous la pièce car il n’y a aucune protection contre la lame à
cet endroit.
• Vérifier le protège-lame inférieur afin de s’assurer qu’il soit bien fermé avant d’utiliser l’outil; ne pas faire fonctionner ce dernier si le protège-lame ne se déplace pas
librement ou s’il ne se ferme pas instantanément. Ne jamais le bloquer en position ouverte.
Si on laisse tomber la scie, soulever le protège-lame inférieur au moyen du levier
d’escamotage et le vérifier afin de s’assurer qu’il n’y ait aucun dommage, qu’il se déplace
librement et qu’il n’entre pas en contact avec la lame ou toute autre pièce de l’outil, quels
que soient l’angle et la profondeur de coupe.
• S’assurer que le ressort du protège-lame inférieur soit en bon état de fonctionnement; sinon, on doit lui faire subir un entretien avant d’utiliser l’outil. Le protège-
lame peut être difficile à déplacer en présence de pièces endommagées, de dépôts gommeux ou de débris accumulés.
• On ne doit escamoter manuellement le protège-lame inférieur que pour réaliser une
coupe spéciale, complexe ou à partir de l’intérieur d’un matériau. Pour ce faire, on
doit le soulever au moyen du levier d’escamotage, relâchant ce dernier dès que la lame
mord dans la pièce. Le protège-lame s’escamote automatiquement pour tous les autres
types de coupe.
• Toujours s’assurer que le protège-lame inférieur recouvre la lame avant de déposer
la scie sur le plancher ou sur un établi, car, sans protection, une lame qui tourne
encore fait reculer la scie, coupant tout ce qui se trouve sur son passage. Il est en outre
bon de savoir combien de temps la lame prend pour s’arrêter une fois l’interrupteur relâché.
• Ne JAMAIS tenir la pièce dans ses mains ou la placer sur ses jambes pour la couper.
Il est important de soutenir la pièce correctement afin d’éviter d’exposer des parties du
corps à la lame, de coincer cette dernière ou encore, de perdre la maîtrise de l’outil.
• Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en
contact avec des fils cachés ou son propre cordon, car de tels contacts peuvent mettre
les pièces métalliques de l’outil sous tension, engendrant des risques de choc électrique.
• Toujours utiliser un guide de refend ou de bord droit lorsqu’on effectue une coupe en long
afin d’assurer la précision de cette dernière et d’éviter de coincer la lame.
• Toujours utiliser une lame munie d’un arbre dont les orifices sont de dimension et
de forme appropriées (ronds ou en losanges); les lames qui ne correspondent pas aux
éléments de fixation de la scie tourneront de manière excentrique, faisant perdre la
maîtrise de l’outil.
• Ne jamais utiliser de rondelles ou de boulons endommagés ou autres que ceux qui
ont été conçus pour la scie, afin d’obtenir un rendement optimal et de travailler en toute
sécurité.
DWXXX
Loading...