DeWalt DW328K TYPE 4, DW328K TYPE 3, DW328 TYPE4, DW328 TYPE3 Owner’s Manual

<_o')

NI.U

"O Z

>-o

___F-

oo ND

rr_ W_--

r_(D

w _z

E"'

z(/)

O'W

C3< © ©<a_

>'r-d

Fz O<rr Drr<

r./) W

.-_ "O

_L_ =m

,I 8

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the "D" shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Instructions

_ WARNING! Read and understand all instructions. Failure to foflow aft

instructions listed below may result in electric shock, fire and/or serious

personal inju_

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep bystanders, children, and visitors away while operating a power tool Distractions can cause you to lose control

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician ff you are in doubt as to whether the outlet is properly grounded, ff the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked

"W-A" or "'W." These cords are rated for outdoor use and reduce the risk of electric

shock. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating, ff in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300 Ampere Rating

More Not more AWG

Than Than

0 6 18 16 16 14 6 10 18 16 14 12

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious personal injury

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents often cover moving parts and should

also be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools

with your finger on the switch or plugging in tools that have the switch on invites

accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control

• Do not force tool Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tooL Such preventative safety measures reduce

the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control

• Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool's operation, ff damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on

another tool

SERVICE

• Tool service must be performed only by qualified repair personneL Service or main- tenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

Additional Safety Rules for Portable Band Saws

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will make exposed

metal parts of the tool "live" and shock the operator.

• Keep hands away from cutting area and blade. Keep one hand on the main handle

and the other hand on the front handle to prevent loss of control which could result in personal injury.

• Always make sure the portable band saw is clean before using.

• Always cease operation at once if you notice any abnormality whatsoever.

• Always be sure all components are mounted properly and securely before using tooL

• Always handle the band saw blade with care when mounting or removing it.

• Always keep your hands out of the line of the band saw blade.

• Always wait until the motor has reached full speed before starting a cut.

• Always keep handles dry, clean, and free of oil and grease. Hold the tool firmly when in

use.

• Always be alert at all times, especially during repetitive, monotonous operations. Always be sure of position of your hands relative to the blade.

• Never remove material guide/work stop.

• Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/or heavy. Serious personal injury may result.

_ WARNING: DO NOT modify and/or use this tool for any application other than for which it was designed.

WARNING: Shock Hazard. Exercise extreme caution when cutting blind into conduit and

pipe. Be sure the object being cut does not contain electrical wires, gases, or water, etc.,

which could create hazardous conditions causing personal injury and property damage.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

• A void prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

_ WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face and body.

• The label on your tool may include the following symbols. The symbols and their defini-

tions are as follows:

V ............ volts

Hz .......... hertz

min .......... minutes

.... ........direct current

(_)............ Class I Construction

(grounded)

[] ............ Class II Construction

(double insulated)

sfpm ........surface feet per minute

A................ amperes

W .............. watts

* ............ alternating current

no .............. no load speed

.............. earthing terminal

.............. safety alert symbol

.../min ........ revolutions or reciprocation

per minute

SAVE THESE INSTRUCTIONS

COMPONENTS (FIG. 1, 2)

A. Auxiliary handle I. Speed wheel B. Lock button J. Blade

C. Trigger switch K. Rubber tires D. Main handle L. Pulley E. Material guide/Work stop M. Blade guard

R Guide rollers

G. Blade tracking adjustment

H. Blade tension lever

ASSEMBLY

Blades

This portable band saw is setup for use with .020" (0.5 mm) thick, 1/2" (12.5 mm) wide and 44-7/8" (1140 mm) long blades. To use .025 (.64 mm) thick blades, please contact an

authorized DEWALT service center.

WARNING: The use of any other blade or accessory might be hazardous. DO NOT use

any other type of accessory with your band saw. Blades used on stationary band saws are of different thickness. Do not attempt to use them on your portable unit.

Blade Selection

In general, first consider the size and shape of the work, and the type of material to be cut. Remember, for the most efficient cutting, the coarsest tooth blade possible should be used in a given application, because the coarser the tooth, the faster the cut. In selecting the appro- priate number of teeth per inch of the band saw blade, at least two teeth should contact the work surface when the blade is rested against the workpiece. As a rule of thumb, soft materi- als usually require coarse tooth blades, while hard materials require fine tooth blades. Where a smoother finish is important, select one of the finer tooth blades.

Select the appropriate band saw blade according to the material type, dimensions, and num- ber of teeth. See Blade Description chart.

_, CAUTION: The following table is intended as a general guide only. Determine the type of

material and dimension of the workpiece and select the most appropriate band saw blade.

Incorrect blade application may result in loss of control causing personl injury

FIG 4

_, CAUTION: Never use the band saw to cut resin materials which are subject to melting,

Melting ot resin material caused by high heat generated during cutting may cause the band saw blade to become bound to the material, possibly resulting in overload and bum-out of #be

motor.

BLADE DESCRIPTION

Type of _d saw blade DiStal

Number of tee_ per inch 24 / 18 14 10 1i4/18 i0/14

Workplece _lckness /

1/8" and under • I • !

FIG. 5

1/8"-1/4" • / •

t/4"- !3/32" * •

13/32" and over

',-'our DW328 portable band saw is equipped with variable speed for greater versatility. Turn the speed wheel (I) to select the desired speed (Fig, I ), Speed 1 is the slowest speed; Speed

6 is the fastest, Use speed settings 1-6 when connected to an AC power supply. When connected to a DO power supply the setting MUST be Speed 6.

CAUTION: To avoid damage to the variable speed s_cVtch,always use Speed 6 (fastest) when using a DC power source. Always turn the saw off, set the speed wheel (I) to Speed 6,

then turn the saw eric

When cutting copper, brass, bronze, atuminum, cast Iron, angle iron, and mild steel, use a

higher speed,

When cutting plastic pipe, tougher steels, chro_ steel, tungsten steel stainless steel, and other problem rnateriats, use low s_ed,

NOTE: When cutting piaatic pips, higher speeds may melt plaatic,

Removing and Installing Blades

_ WARNING: Turn off and unplug the tool before making any adjustments or

removing/Tnstalling attachments or accessories, _ CAUTION; Cut Hazard. Blade tension lever is under spring pressure. Maintain control of

lever when releasing blade tension or blade may bo rdeased causing persof_a! injury.

TO REMOVE BLADE (FIG, t, 2)

1, Rotate the blade tension lever (H) clockwise until it stops to release tension in blade,

2. Turn the saw over and place it on a workbench or table with the cord to the left. 3, Begin removing the blade at the b_ade guard (M) and continue around the pulleys (L),

When removing the blade, tension may be released and the blade may spring free. SAW

BLADES ARE SHARP. USE CARE IN HANDLING THEM.

4. Inspect the guide rollers (Ff, F2) and remove any large chips which may be lodged in them. Lodged chips can prevent rotation of the guide rollers and cause flat spots on the guide rollers.

5. Rubber tires (K) are rreunted on the puileys (L). The rubber tires should be inspected for looseness or damage when changing the blade, Wipe any chips from the rubber tires on

the pulleys. This will extend tire life and keep the btade from slipping. If any looseness or damage occurs, the tool should be brought to an authorized D_:WALT service center for

repair or replace_nt as soon as poesible, Continued use of the tool w_h loose or

damaged rubber tires will cause unstable travel of the band saw blade.

TO INSTALL BLADE

1. Position the blade so that the teeth are on the bottom and angled toward the _terial

guide/work stop, as shown in Figures 1 and 3, 2, Slip the blade into the guide rollers (F), as shown in Figure 4, 3 Holding the blade in the guide rollers, place it around both pulleys (L) and through the

material guiddwork stop (E), as shown in Figure 5.

4, Make sure that the blade is fully inserted into the guide rollers (F) and positioned square-

ly against the rubber tires (K),

5, Gently turn the _w over so that the pulleys rest on your work bench or table and rotate

the blade tension lever (H) counterclockwise until it stops. Make sure the teeth face away

from the handsaw (Fig, 1,3),

6. Turn the saw on and off a few times to ensure that the blade is seated properly.

Blade Tracking

WARNING: Turn off and unplug the tool before making any adjustments or

removing/tnstalling attachments or accessories,

Your bend saw is equipped with an adiustable blade tracking mechanism which a.%ures

proper blade tracking at all times, The back edge of a properly aligned blade will run

lightiy against one or both of the back up rollers in the blade guides, (The pressure between the edge of the blade and the roller will be very slight and wil! not damage either the blade or the roller.)

TO ADJUST THE BLADE TRACKING

1 Use a 9/16" (20ram) wrench to loosen the adjustment locking nut (G), shown in Figure !

by turning it one or two turns counterclockwise.

Z Use a _rewdriver to turn the tracking screw !/4 turn, Turn{rig the screw clockwise will

move the blade up toward the blade guide rollers. Turning the _rew counterclockwise

will move the blade down away from the rollers,

3. Adjust so that the back edge of the blade lightly touches the rollers then securely tighten the locking nut. tit will De ne_ssary to p_ug the saw in and run it to observe the tracking.)

4, Observe blade tracking between runs and repeat Steps 1-4 as necessaG, to achieve

proper blade tracking.

FIG, 7

RECOMMENDED CUTTING POSITIONS/POSmONS DE COUPE RECOMMANDEES 1 POSICIONES DE CORTE RECOMENDAD_

YES / OUI / SI NO / NON / NO YES /OUI / SJ NO / NON / NO

YES / OUi / S{ NO / NON / NO YES / OUI /S{ NO / NON / NO

YES / OUI / S[ NO/NON/NO YES fOUl / S{ NO/NON/NO

Item

Motor

Band Saw

Blade

Max. Cutting Pipe outer dimensions 4-3/4 ° (120 mm_

Dimensions Stock 4_1/2 _x 4-&/4" (114 mm x 120 mm)

Net Weight t4 Ibs. (6.4 kg)

Cord 3 conductor type captive cable 8,0 ft, (24 m)

Article Mod_ DW328

Moteur Ty£e .................................................................................................................T)@e2_t_9 _

Lame de scla Dimensions 12,5 mm x 1 140 mm x 0,5 mm

Model DW328

. Type ...... Protected commutator motor

FuNoad current 6 amp Dimensions 1/2° x 44W/8" x .020"

........................................................................................................._!,2:5rnrnx !_.@mmx:,5m_....................................

Peripheral speed 100 - 265 ft/min (30 =80 m/rain)

Circu_ d'alimentation _lectrique mon ophas_, ca,, 60Hz Tension 120 volts

Oourant de #e!ne charge 6 A

r_ban ............................................................ o._._} __...._____.

Dirr_en_ons Dimensions externes du tuyau 120 mm (4-3/4 pc)

maximales Mat@riau & seuper 114 mmx 120 mm

de la cou_ (4-1/2 pox 4-3/4 pc)

Poids net 6,4 kg (14 !b}

Cordon Fiche & 3 broches et & 3

A_°culo Modelo DW328

Motor TipQ Motor conm_ador en eerie, t!_o £_o .......

Hoja de la sierra Dimensiones t2,5 mm x 1 140 mmx 0,5 mm

de ba_da ..................................................................(1o/22U)g, X_:7/8 pulg: X :_0 £#1#:).........................

D|meneiones Dimensiones extefiores

_imas de ,de tube[[a ..................................................._29 :q_ _4:3_4 oPu!_:).........................................................................................

code Material a cortar 114 mm x 120 mm {4-1/2 x 4-3/4 pulg_)

Peso neto 6,4 kg (14 Ib}

Cable Cable cautivo de 3 conductores, de 2A m

Vbesse !_ripherique 30 & 80 m/rain (100 - 285 p_imin)

conducteurs de 2,4 m (8,0 pi))

Fuente de atimentaci5n CA 60 Hz, mono_sica Voltaje 120 ve_tios

Corriente a _tena carga 6 amperios

Velocidad per_ferica 30 - 80 m/min (100 - 265 piedmin)

(8,0 pies) de largo

OPERATION Motor

Be sure your power supply agrees with the voltage marked on the nameplate. 120 Volts AC 60Hz means alternating current only. Voltage decrease of more than 10% will cause loss of

power and overheating. All DEWALT tools are factory-tested. If this tool does not operate, check the power supply line for blown fuses and the plug and receptacle for proper contact. This band saw is designed to cut various types of material up to 4-3/4" (120 mm) diameter

or 4-1/2" (114 mm) x 4-3/4" (120 mm) rectangular shape at 90°.

i_ WARNING: Thoroughly remove any oil or grease from the workpiece before securing in a

vise or other clamping device. If the workpiece is not secure, # may come loose during the

cutting and/or cause breakage, which may result in serious personal injury.

_, WARNING: Never connect the tool to a power source unless the voltage of the source is the same as the voltage specified on the nameplate of the tooL An overspeed blade and overheating and may occur causing personal injury.

J&WARNING: Laceration Hazard. If the power cord is connected to the power source with the trigger switch turned ON the power tool will start suddenly and could cause a serious

accident.

Trigger Switch (Fig. 1)

To start the tool, squeeze the trigger switch (C). To turn the tool off, release the switch. A lock button (B) is provided to keep the saw running without holding the trigger switch "ON."

To lock the switch trigger "ON," squeeze the trigger as far as it will go, push in the lock

button and release the trigger. To disengage the lock button, squeeze and release the trigger

switch.

Cutting

i_ WARNING: Refer to Figure 7 for recommended cutting positions for various materials. Loss of control causing serious injury may occur.

NOTE: Select and use a band saw blade that is most appropriate for the material being cut. For more information, refer to Blade Selection.

1. Mount the material to be cut solidly in a vise or other clamping device. Never attempt to use this tool by resting it on a work surface and bringing the material to the tool. Always

securely clamp the workpiece and bring the tool to the workpiece, securely holding the

tool with two hands as shown in Figure 6.

2. Bring the material guide/work stop (E) into contact with the workpiece. Turn the saw ON.

3. When saw reaches desired rotation speed, slowly and gently tilt the main body of the tool to bring the band saw blade into contact with the workpiece. Do not apply additional pres-

sure in excess of the weight of the main body of the tool. Carefully avoid bringing the band saw blade suddenly and heavily into contact with the upper surface of the workpiece. This will cause serious damage to the band saw blade. To obtain maximum service life of the

band saw blade, ensure there is no sudden impact at the beginning of the cutting opera-

tion.

A CAUTION: During cutting, ff the band saw becomes locked or jammed in the workpiece

material release the switch immediately to avoid damage to the band saw blade and motor.

4. The tool's own weight provides the most efficient downward cutting pressure. Added

operator pressure slows the blade and reduces blade life.

5. End pieces, which would be heaw enough to cause injury when they drop, after cut-off, should be supported. Safety shoes are strongly recommended. End pieces may be hot.

6. Hold the saw firmly in both hands so that the saw does not fall against clamped or supported material when the cut is completed. DO NOT MAKE ANY SPEED CHANGES

UNLESS TOOL HAS BEEN TURNED OFF.

Tips for Better Cutting

The following recommendations should be used as a guide. Results may vary with the oper-

ator and the particular material being cut.

• Never twist the band saw blade during cutting operation.

• Never use liquid coolants with portable band saws. Use of liquid coolants will cause build- up on tires and reduce performance.

• If excessive vibration occurs during the cut, turn the bandsaw off and adjust the speed slightly. Ensure that the material being cut is is securely clamped down. If vibration continues, change the band saw blade.

MAINTENANCE

WARNING: To avoid accidental injury, turn off and unplug the tool before making

any adjustments, performing any maintenance or inspection of this tool

Cleaning

_ CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic

parts of the tooL These chemicals may weaken the plastic materials used in these parts. Use

a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Periodically remove chips and other waste material from the surface of the power tool by using a damp cloth and mild soap. Many household cleaners contain chemicals which could

seriously damage plastic. Also, do not use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products. To avoid malfunction of the motor, protect it from contact

with oil or water.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should

be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. Always use identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please

contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800- 4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.

_, WARNING: The use of any other accessory not recommended for use with this tool could

be hazardous.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date of purchase. This warranty does not cover part failure due to nor-

mal wear or tool abuse. For further detail of warranty coverage and warranty repair informa-

tion, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does

not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any

time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund - no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For prod- ucts sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement.

"DW328,,,,,oLE,.....o..........,,w

T0REgUCETHEfrISKOFiNJURY,USERMUST

MA,_UA_,.USE01_LyID_I_lrlCALREPLACE_Et_TPA_TS.A_.WAYSUSE 1"I_OpEREYEA_DR_SPIRATO_','P_0TECTION.

_ PAPA_IS_I_IUPlELRIESGODE VCOMpRE_IDERELMANUALDEINS_UCClONES.UTOIC_SOtaME_TE

PIEZASDER_PUESTOID_NTICAS.SlEMPRES_OEBERAL_EVAR_ PROTECClO_APROP_DAPARA_ VISTAYPAPAI_S VlAS

RESPI_TO_I_S.

O_SPIECESDE_ECHAN_EIDE_llQUES.ILFAUTTOUJOU_SPORTERDE UE_IUIpEMEm"OEPROTECTIONOCUtAI_ETRESPIRA_OI_EAppRspIllE.

_,WALTI_DUS_t_L_OOL¢0.,_TIMO_E,t_o Z_ U.S.A.

READANDUNDERSTANDINSTtiUCTIOI_

LESlON_S,EtUSUA_IOD_BE_AL_E_

AFI_DE_INIMISE_tES_IS_UES 0_ ItLESSU_ES,L'UTIt_S_T_U_

SI VOUS AVEZ DES QUESTIONS OU VOUS VOULEZ NOUS FAIRE PART DE VOS COMMENTAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL DEWALT, COMPOSEZ SANS FRAIS LE : 1 800 433-9258. (1-800-4-DEWALT).

Consignes de sdcuritd - gdndralitds

AVERTISSEMENT : Lire, comprendre et suivre toutes les directives

pr_cis#es ci-dessous afin d'eviter les risques de choc electrique, d'incendie ou de blessure grave.

CONSERVER CES DIRECTIVES

AIRE DE TRAVAIL

• Carder I'aire de travail propre et bien eclairee; les #tablis encombr#s et les endroits sombres sont propices aux accidents.

• Ne pas utiliser les outils electriques clans une atmosphere explosive, comme

proximite de liquides, de gaz ou de poussieres inflammables; le moteur peut crier

des #tincelles et enflammer les vapeurs ou les poussi#res environnantes.

• Tenir les enfants, les visiteurs ou toute autre personne a I'ecart Iorsqu'on utilise un outil electrique; les distractions peuvent faire perdre la maftrise de ce demier.

MESURES DE SI_CURITI_ - I_LECTRICITI_

• Les outils mis a la terre doivent #tre branches clans une prise correctement instal- lee et mise a la terre tel que I'indiquent les codes et reglements en vigueur. Ne

jamais retirer la broche de mise a la terre ou modifier la prise en aucune faFon. Ne pas utiliser de fiche d'adaptation. Consulter un electricien qualifie s'il y a un doute

en ce qui concerne la mise a la terre de la prise. En cas de d#faillance #lectrique ou de bris de I'outil, la mise a la terre procure un chemin de faible r#sistance au courant afin de r#duire les risques de choc #lectrique.

• _:viter tout contact entre le corps et les elements mis a la terre, comme les tuyaux, les radiateurs, les cuisinieres et les refrigerateurs, afin de r#duire les risques de choc

_lectrique.

• Ne pas utiliser I'outil electrique clans des endroits mouilles, ni I'exposer a la pluie; I'infiltration d'eau a I'int_rieur de I'outil augmente les risques de choc _lectrique.

• Ne pas utiliser le cordon de maniere abusive; on ne dolt pas transporter I'outil en le tenant par le cordon, ou utiliser ce dernier pour le debrancher. On doit tenir le cordon a I'ecart des sources de chaleur, de I'huile, des bords tranchants ou des

pieces mobiles. Remplacer immediatement les cordons endommages, car ces

demiers augmentent les risques de choc #lectrique.

• Lorsqu'on utilise un outil electrique a I'exterieur, on ne dolt utiliser que des railonges con¢ues pour cet usage, comme ceiles de type W-A ou W, afin de r#duire les risques de choc #lectrique. S'assurer que la rallonge est en mesure de porter le courant n#cessaire a I'outiL Une rallonge de calibre inf#rieur entrafnera une chute de tension se traduisant par une perte de puissance et une surchauffe. Le tableau ci-dessous

illustre les calibres que I'on doit utiliser selon la Iongueur de la rallonge et I'intensit# nominale indiqu#e sur la plaque signal#tique. En cas de doute, utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut porter de courant.

Calibre minimal des cordons de rallonge

Tension Longueur totale de la rallonge en m_tres

120V De 0 &7,6 De 7,6 & 15,2 De 15,2 & 30,4 De 30,4 & 45,7

240V De0&15,2 De15,2&30,4 De30,4&60,9 De60,9&91,4

Intensit_ nominale (en amperes) Plus dePas plus de Calibre AWG

0 6 18 16 16 14 6 10 18 16 14 12

SECURITE PERSONNELLE

• Rester vigilant en tout temps et faire preuve de jugement Iorsqu'on utilise un outil electrique. Ne pas utiliser I'outil Iorsqu'on est fatigue ou sous I'influence de drogues, d'alcool ou de medicaments, car un moment d'inattention pourrait entra_ner

des blessures graves.

• Porter des v#tements appropries. Ne pas porter des v#tements amples ou des bijoux. Couvrir ou attacher les cheveux longs. Carder les cheveux, les v#tements,

les bijoux et les gants eloignes des pieces mobiles, car ceux-ci peuvent s'y coincer. Se tenir #loign# des #vents puisque ces demiers pourraient camoufler des pi_ces

mobiles.

• _:viter les demarrages accidentels; s'assurer que I'interrupteur est en position d'arr#t avant de brancher I'outil. A!e pas transporter I'outil en laissant le doigt sur

I'interrupteur nile brancher Iorsque I'interrupteur est en position de marche, car cela

pourrait causer un accident.

• Retirer les cles de reglage avant de demarrer I'outil. Une cl# laiss#e sur une piece rotative pourrait entrMner des blessures.

• Ne pas trop etendre les bras. Les pieds doivent rester ancres fermement au sol afin de maintenir son equilibre en tout temps et de mieux maftriser I'outil dans des situa-

tions impr#vues.

• Utiliser le materiel de securite approprie; toujours porter des lunettes de protection. Porter un masque anti-poussi_res, des chaussures antid#rapantes, un casque de

s#curit# ou des protecteurs auditifs Iorsque la situation le requiert.

UTILISATION ET ENTRETIEN DE L'OUTIL

• Fixer et soutenir la piece sur une plate-forme stable au moyen d'une bride de serrage ou de tout autre dispositif semblable. La piece est instable Iorsqu'on la retient

manuellement ou qu'on I'appuie contre le corps, ce qui pourrait faire perdre la maftrise de I'outiL

• Ne pas forcer I'outil ni I'utiliser pour des travaux autres que ceux pour lesquels il a ete conFu. Pour obtenir de meilleurs r#sultats et pr#venir les risques de blessure, laisser

I'outil couper a la vitesse pour laquelle il a#t# congu.

• Ne pas utiliser I'outil Iorsque I'interrupteur marche-arr#t ne fonctionne pas. Tout outil qui ne peut _tre command# au moyen de I'interrupteur est dangereux et doit _tre r_par_

• Debrancher I'outil de la source d'alimentation electrique avant d'effectuer un reglage, de changer les accessoires ou de ranger I'outil; ces mesures de s_curit_

preventives r_duisent les risques de d_marrage accidentel.

• Lorsqu'on n'utilise pas I'outil, le ranger hors de la portee des enfants ou des

personnes non qualifiees. Les outils sont dangereux entre les mains de personnes

inexp#riment#es.

• Bien entretenir I'outil; s'assurer qu'il est toujours bien propre et aiguise. Les outils bien entretenus et dont les bords sont bien tranchants sont moins susceptibles de rester coinc#s et sont plus faciles a maftriser.

• Verifier les pieces mobiles afin de s'assurer qu'elles sont bien alignees et qu'elles ne restent pas coincees. Verifier egalement les pieces afin de s'assurer qu'il n'y a aucun bris ni aucune autre condition susceptible de nuire au bon fonctionnement de I'outil. Faire reparer I'outil si ce demier est endommage avant de s'en servir

nouveau, car les accidents sont souvent causes par des outils mal entretenus.

• N'utiliser que les accessoires recommandes par le fabricant pour le modele concerne. Un accessoire destin# a un outil particulier peut devenir dangereux Iorsqu'il est

utilis# avec un autre.

ENTRETIEN

• L'outil dolt #tre entretenu par le personnel qualifie seulement; toute maintenance effectu#e par une personne non qualifi#e pourrait entrafner des risques de blessure.

• Lors de I'entretien, n'utiliser que des pieces de rechange identiques et suivre les directives precisees a la section ,, Entretien _ du present guide afin de pr#venir les

risques de choc #lectrique ou de blessure.

R_gles de s_curit_ additionnelles concernant les scies a ruban portatives

• Tenir I'outil par les surfaces isolees prevues a cette fin Iorsqu'il risque d'entrer en contact avec des ills caches, car de tels contacts peuvent mettre les pi_ces m_talliques

de I'outil sous tension, engendrant des risques de choc #lectrique.

• Tenir les mains eloignees de I'aire de coupe et de la lame. Garder une main sur la

poign#e principale et I'autre, sur la poign#e avant afin d'#viter de perdre la maftrise de

I'outil et de risquer des blessures.

• Toujours s'assurer que la scie a ruban portative est propre avant de I'utiliser.

• Toujours arr#ter imm#diatement le fonctionnement de la scie Iorsqu'on remarque une

anomalie.

+ 4 hidden pages