DS630/DS630B WIRELESS CABLE LOCK
DS630-6, DS630-12 AND DS630-24
REPLACEMENT CABLES
NOTE: This product works only with the DS600 Mobilelock™
LK
C
GENERAL SAFETY RULES
WARNING: Read and understand all instructions and
warnings for this product.
In addition, read and follow all instructions and warnings provided
with the DS600 Mobilelock™ Portable Alarm System.
CAUTION: DANGER OF EXPLOSION, INJURY, OR FIRE.
Carefully follow all instructions and warnings on the battery label
and package.
• Never use a damaged or worn out battery.
• Discharged batteries should be replaced only with type
CR-123 3.0 Volt Lithium batteries.
• Do not use re-chargeable batteries or attempt to charge
batteries.
• Carefully remove the old, discharged battery.
• Do not attempt to open.
• Do not peel the label from the battery.
• Never dispose of a battery in a fire.
• Dispose of used batteries in accordance with local regulations.
• Recycle batteries.
• Always insert batteries correctly with regard to polarity
(+ and -) marked on the battery and the equipment.
• When installing the battery, do not use excessive force. If the
battery does not fit, check to make sure that it matches the
polarity markings.
• Never expose the battery terminals to any other metal object.
This can short circuit the battery.
• Avoid exposure to temperature extremes.
• When not in use, store the battery in a cool, dark, dry place.
• Keep batteries out of reach of children.
FCC REGULATORY STATEMENT (FCC: 2ABPY-BB4EA)
• This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) the device must accept
any interference received, including interference that may
cause undesired operation.
Important
• The Cable Lock uses a cable with a stainless steel braid. If
the exterior coating is cut, torn or abraded, the exposed metal
could short out equipment. Immediately replace the cable.
Replacement cables (6' (1.83m), 12' (3.66m) and 24' (7.32m)
lengths) are available as an additional accessory.
• To avoid constant unsecured alarms, be sure that the Cable
Lock is closed while it is not being used.
• Inspect the gasket whenever the housing is opened and
replace if worn or damaged. Be sure the gasket is in the proper
position before closing the housing.
• This product is designed for indoor/outdoor use.
FIG. 1 FIG. 2
A
J
B
D
FIG. 3
G
F
E
M
Components
A. Gasket D. Cable Lock Lever G. Battery
B. Inner Housing E. Reset Button
C. Outer Housing F. Tamper
Product Function
The DS630 Cable Lock has a 12' (3.66m) cable impregnated with
a heavy duty urethane jacket over stainless steel braiding which
provides strength, durability and flexibility. As the cable ends
are disconnected, the system will be notified of an unsecured
device. Once activated, this device will work exclusively with the
assigned DS600 Mobilelock™ Portable Alarm System.
1. The DS630 contains a locking mechanism with a location
for a standard padlock (not included) to provide additional
security. The addition of a padlock is recommended.
2. The DS630 features a tamper that notifies the system when
the housing has been opened.
3. The DS630 features BLE (Bluetooth® Low Energy) that allows
it to connect wirelessly to the DS600 Mobilelock™. Range
between this sensor and the DS600 can be up to 100' if
unobstructed (line of sight).
NOTE: Metal objects blocking radio frequency (RF) transmission
can affect the range of the sensor
Prevention of False Alarms
The majority of alarms that occur are false. These situations
happen every day due to user error, incorrect installation or
improper maintenance of the system. False alarms will limit
the responsiveness to the system and become a general
inconvenience. As the number of false alarms increases,
authorities have become less apt to respond to alarm systems
due to this problem. Many of these situations can be avoided by
following some very simple practices.
•
Ensure all users are properly trained on the operation of the system.
• Always Disarm the DS600 Mobilelock™ before entering
protected area.
• Check that premises are cleared and assets secured before
Arming the system.
•
Know how to cancel an alarm or turn off the system before activating.
• Test the system on a monthly basis to ensure proper functioning
• Check cellular signal, power supply, and that sensors are
secured on a daily basis.
Recommended Locations
• Secure product off the ground above 3 feet (.91m) to ensure
better communication with the DS600 Mobilelock™
• Recommended for use on mobile equipment, containers,
gates and remote assets.
• Secure assets by wrapping the cable through equipment,
tools, materials or other assets.
• Replacement cables of 6' (1.83m), 12' (3.66m) and 24' (7.32m)
are available at additional cost.
Installing & Changing Battery
This wireless sensor requires a non-rechargeable CR-123 3.0
Volt Lithium battery. If this Cable Lock is newly purchased skip
to Device Registration below as a battery is already installed.
TO CHANGE AND INSTALL A BATTERY
1. Remove five screws from the outer housing (C).
2. Separate housings.
3. Carefully remove the old discharged battery. Dispose of the
battery according to local regulations.
4. Install new battery using the polarity (+ and -) markings on
the battery and equipment. Do not use excessive force. If
the battery does not fit, ensure that it matches the polarity
markings.
5. Press the reset button (E) on the device.
6. Rejoin housings.
7. Reinsert the five screws into the outer housing and tighten.
Securing Equipment
The DS630 has a cable that is impregnated with a heavy-duty
urethane jacket over stainless steel braiding. As the cable ends
are disconnected, the system will be notified of an unsecured
device. Also, if for any reason the circuit is broken (i.e., cable
is cut), the Cable Lock will be considered unsecured and will
send an alarm notification. The Cable Lock needs to be removed
before operating the attached equipment.
TO SECURE
1. Rotate the cable lock lever (D) counterclockwise 90° to open
and wrap cable around equipment.
2. Insert the small cable end (J) as shown in Figure 3.
3. Align the slot (K) on the cable end with the tab (L) on inner
housing (Fig. 2).
4. Rotate the cable lock lever clockwise 90° back to its original
position as shown in Figure 1.
NOTE: A padlock (not included) is recommended for additional security.
TO UNSECURE
1. Rotate the cable lock lever (D) counterclockwise 90° to open.
2.
Disconnect small cable end (J) and remove cable from equipment.
3. Rotate the cable lock lever clockwise 90° back to its original
position.
Replacing/Changing Cable
The system must be disarmed prior to any changes.
1. Rotate the cable lock lever (D) counterclockwise 90° to open.
2. Remove five screws from the outer housing (C).
3. Separate housings.
4. Push the large end (M) of the cable through the large hole in
the outer housing until all of the cable is through.
5. Insert the small end (J) of the new cable through the large
hole in the case from the inside and feed the cable through
until the large cable end is stopped by the outer housing.
6. Vertically align the rectangular end to fit into the inner case
receptacle and pull to tighten. -
7. Insert the small cable end into the inner housing, aligning the
slot (K) and tab (L). Rotate the cable lock lever back to its
original position.
8. Rejoin the housings.
9. Reinsert the five screws into the outer housing and tighten.
10. The Cable Lock is ready for use (see Securing Equipment).
Device Registration
To activate this sensor, it must first be assigned to your DS600
Mobilelock™ Device. Instructions for assigning your sensor can
be found within your online Mobilelock™ account.
NOTE: This sensor can be assigned to only one DS600
Mobilelock™ device at a time.
1. Log into your online Mobilelock™ account.
2. Select the Mobilelock™ device you wish to pair this sensor to
and go to the Configure Units page.
3.
Click the link titled “Manage Bluetooth®” in the Sensors section.
4. Click to “Enable” Bluetooth®.
5. After the Mobilelock™ device’s Bluetooth® is confirmed
“Enabled”, click “Add Sensor”. Then hold the Cable Lock
close to the DS600 and click “Scan for available sensors”.
6. When the website shows the sensor, click on it to confirm
your selection.
7. Then configure the sensor: Give it a name (“Front Gate”).
8. Select any optional alerts desired and click “Save and Close”.
9. Make sure the sensor is selected as “Enabled”.
10. After registration, Arm the DS600 Mobilelock™ and test the
sensor.
TEST
With the DS600 Armed open up the DS630 Cable Lock. Check
to see that the Cable Lock alarm was received in the Event
History for the DS600 Mobilelock™ on the Configure Units page
and also that notification of the alarm was received as per the
settings on the Alarm Contacts page.
Full One Year Warranty
The DeWALT Mobilelock™ Portable Alarm System is warranted
for one year from date of purchase. We will repair, without charge,
any defects due to faulty materials or workmanship. For warranty
repair information, visit www.dewaltmobilelock.com or email us
at info@dewaltmobilelock.com. This warranty does not apply to
accessories or damage caused where repairs have been made
or attempted by others. This warranty gives you specific legal
rights and you may have other rights which vary in certain states
or provinces.
DeWALT, GUARANTEED TOUGH, and the yellow and black
color scheme are trademarks of the DeWALT Industrial Tool Co.
used under license. Mobilelock™ is a trademark of Mobilelock
LLC. Manufactured by Mobilelock LLC: 550M Ritchie Hwy #279,
Severna Park, MD 21146.
Loading...