Page 1
DE0881-XE
TRIPOD
INSTRUCTION MANUAL
Page 2
Page 3
1
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if
not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US AT: 1800 444 224 (Aust) or 0800 339 258 (NZ).
Technical Data
DE0881
Threaded pin M6 x 20
Max height cm 172
Weight kg 1,5
SAFETY INSTRUCTIONS
Always observe the safety regulations applicable in your country to reduce the risk of
fire, electric shock and personal injury. Read the following safety instructions before
attempting to operate this product. Keep these instructions in a safe place.
WARNING: To reduce the risk of injury, read the instruction manual.
WARNING! Read all safety warnings and all instructions Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious
injury.
Read all of this manual carefully before operating the attachment. Also refer to the
manual of any power tool that will be used with this attachment.
SAVE THESE INSTRUCTIONS
GENERAL WARNINGS
1. Keep work area clean.
Cluttered areas and benches can cause accidents.
2 . Keep children away.
Do not let children come into contact with the tool or extension cord. Super vision
is required for inexperienced users.
3. Use appropriate tool.
The intended use is described in this instr uction manual. Do not force small tools
or attachments to do the job of a heavy-duty tool. The tool will do the job better
and safer at the rate for which it was intended.
WARNING: The use of any accessory or attachment or performance of any
operation with this tool, other than those recommended in this instruction manual may
present a risk of personal injury.
Page 4
2
FIG. 1
E
A
B
D
E
F
C
C
I
J
E
H
G
DESCRIPTION (FIG. 1)
WARNING: Never modify the tripod or any part of it. Damage or personal injury
could result.
A. Rotary head mount F. Mounting thread
B. Quick-adjust latch G. Locking collar
C. Legs H. Elevator column
D. Elevator crank handle I. Elevator lock knob
E. Foot J. Bubble level
INTENDED USE
Your tripod has been designed to extend the capabilities of your laser. The tripod helps
to position the laser on rough, out-of-level surfaces. The tripod can be used both
indoors and outdoors.
DO NOT let children come into contact with the attachment or laser. Supervision is
required when inexperienced operators use this attachment.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and applicable regulations.
WARNING: Refer to the laser manual to be used with this attachment.
Bubble Level
Use the bubble level (J), located under the rotary head mount (A), to ensure the tripod
is level.
Tripod Setup
1. Spread the legs (C) apart to install the tripod in upright position.
2. Tighten the locking collar (G).
3. Adjust the legs (C) if required so that each of the feet (E) is firmly touching the
ground.
4. Mount the laser on the tripod.
Page 5
3
Adjusting the Leg Height
1. Release the quick-adjust latch (B) of the first leg (C) to set the desired height.
Tighten the latch.
2. Repeat process for the other legs.
Mounting the Laser to the Tripod
The tripod has been equipped with a threaded pin for mounting of the DW088-XE and
DW089-XE lasers.
1. Install the tripod on a relatively smooth and level surface, using the bubble level
(J) as a guide.
2. Mount the laser to the tripod by turning the mounting thread (F) into the
receptacle in the base of the laser.
WARNING: Before mounting a laser to the tripod, check that the legs are firmly set
and that the tripod is wobble free.
Elevating the Head Mount
The head mount (A) can be elevated to a maximum height of 1.7 m. The laser is
operated using the elevator crank handle (D). Move the head mount to the desired
height and tighten the elevating lock knob (I).
Storage
In order to conveniently store the attachment, a carrying bag is included.
MAINTENANCE
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been
tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available at extra cost from
your local service center. If you need any assistance in locating any accessory, please
contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call
1800 444 224 or (NZ) 0800 339 258.
Page 6
Page 7
Page 8
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ)
www.dewalt.com.au • www.dewalt.com.nz
(JAN12) Part No. N157163 DE0881-XE Copyright © 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;
the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
Loading...