Desa Tech SPC-40, SPC-40A Owner's Manual

PROPANE CONSTRUCTION FORCED AIR HEATER

OWNER’S MANUAL

35/40,000 BTU/HR HEATER

IMPORTANT: Read and understand this manual before assembling, starting or servicing heater. Improper use of heater can cause serious injury. Keep this manual for future reference.

GENERAL HAZARD WARNING:

Failure to comply with the precautions and instructions provided with this heater, can result in death, serious bodily injury and property loss or damage from hazards of ﬁre, explosion, burn, asphyxiation, carbon monoxide poisoning and/or electrical shock.

Only persons who can understand and follow the instructions should use or service this heater.

If you need assistance or heater information such as an instructions manual, labels, etc. contact the manufacturer.

TABLE OF CONTENTS

Safety Information ............................................... 2

Unpacking ........................................................... 3

Product Identiﬁcation ........................................... 3

Theory of Operation ............................................ 4

Propane Supply ................................................... 4

Installation ........................................................... 4

Ventilation ........................................................... 5

Operation ............................................................. 5

Storage ................................................................ 6

Save this manual for future reference.

For more information, visit www.desatech.com

Maintenance ........................................................ 7

Service Procedures ............................................. 7

Speciﬁcations

Troubleshooting .................................................

Accessories ........................................................11

Technical Services ..............................................

Replacement Parts .............................................11

Illustrated Parts Breakdown and Parts List ....... 12

Warranty and Repair Service ..............

..................................................... 9

Back Cover

SAFETY INFORMATION

WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects or other reproductive harm.

WARNING: Fire, burn, inhalation and explosion hazard. Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. Never use the heater in spaces which do or may contain volatile or airborne combustibles or prod ucts such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.

WARNING: Not for home or recreational vehicle use.

The heater is designed for use as a construction heater in accordance with ANSI Z83.7•CGA2.14-2000. Other standards govern the use of fuel gases and heating products for speciﬁc uses. Your local authority can advise you about these. The primary purpose of construction heaters is to provide temporary heating of buildings under construction, alteration or repair. Properly used, the heater provides safe economical heating. Products of combustion are vented into the area being heated.

We cannot foresee every use which may be made of our heaters. Check with your local ﬁre safety au

thority if you have questions about heater use.

Other standards govern the use of fuel gases and heat producing products for speciﬁc uses. Your local authorities can advise you about these.

Carbon Monoxide Poisoning: Some people are

more affected by carbon monoxide than others. Early signs of carbon monoxide poisoning resemble the ﬂu, with headaches, dizziness and/or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Check for proper ventilation and have heater serviced.

Propane Gas: Propane gas is odorless. An odor-

making agent is added to propane gas. The odor helps you detect a propane gas leak. However, the odor added to propane gas can fade. Propane gas may be present even though no odor exists.

Make certain you read and understand all warn ings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.

1. Install and use heater with care. Follow all local ordinances and codes. In the absence of local ordinances and codes, refer to the

Standard for Storage and Handling of Lique ﬁed Petroleum Gas, ANSI/NFPA 58 and the Propane Gas Installation Code, CAN/CGA B149.2. This instructs on the safe storage and

handling of propane gases.

2. Use only the electrical voltage and frequency speciﬁed on model plate. The electrical con nections and grounding of the heater shall fol low the National Electric Code, ANSI/NFPA 70 or the Canadian Electrical Code, Part 1.

3. Electrical grounding instructions — This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong recep tacle or extension cord.

4. This product has been approved for use in the Commonwealth of Massachusetts.

5. Use only a three-prong, grounded extension cord.

6. Use only the hose and factory preset regulator provided with the heater.

7. Use only propane gas set up for vapor with drawal.

8. Provide adequate ventilation. Before using heater, provide at least a 1.5 ft opening of fresh, outside air.

9. For indoor use only. Do not use heater outdoors.

10. Do not use heater in occupied dwellings or in living or sleeping quarters.

11. Do not use heater in basement or below ground level. Propane gas is heavier than air. If a leak occurs, propane gas will sink to the lowest possible level.

12. Keep appliance area clear and free from com bustible materials, gasoline, paint thinner and other ﬂammable vapors and liquids.

13. Do not use heater in areas with high dust content. Dust is combustible.

(1400 cm2)

www.desatech.com

113855-01B

SAFETY INFORMATION

Continued

14. Minimum heater clearances from combustibles: Outlet: 6 Ft. (1.83 m), Sides: 2 Ft. (0.61 m), Top: 6 Ft. (1.83 m), Rear: 2 Ft. (0.61 m)

15. Keep heater at least six feet from propane tank(s). Do not point heater at propane tank(s) within 20 feet.

16. Keep propane tank(s) below 100° F (37.8° C).

17. Check heater for damage before each use. Do not use a damaged heater.

18. Check hose before each use of heater. If highly worn or cut, replace with hose speciﬁed by manufacturer before using heater.

19. Locate heater on stable and level surface if heater is hot or operating.

20. Not intended for use on ﬁnished ﬂoors.

21. Never block air inlet (rear) or air outlet (front) of heater.

22. Keep heater away from strong drafts, water spray, rain or dripping water.

23. Do not leave heater unattended.

24. Keep children and animals away from heater.

25. Never move, handle or service a hot, operating or plugged-in heater. Severe burns may result. You must wait 15 minutes after turning heater off.

26. To prevent injury, wear gloves when handling heater.

27. Never attach duct work to front or rear of heater.

28. Do not alter heater. Keep heater in its original state.

29. Do not use heater if altered.

30. Turn off propane supply and unplug heater when not in use.

31. Use only original replacement parts. This heater must use design-specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.

UNPACKING

1. Remove all packing items applied to heater for shipment. Keep plastic cover caps (attached to inlet connector and hose/regulator assembly) for storage.

2. Remove all items from carton.

3. Check all items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater.

PRODUCT

IDENTIFICATION

Hot Air Outlet (Front)

Ignitor Button

Automatic Control Valve Button

Hose/Regulator Assembly

Figure 1 - 35,000 Btu/Hr Model Shown

Outer Shell

Handle

Motor

Power Cord

113855-01B

www.desatech.com

Air For Combustion

Air For Heating

THEORY OF OPERATION

The Fuel System: The hose/regulator assembly

attaches to the propane gas supply. This provides fuel to the heater.

The Air System: The motor turns the fan. The

fan pushes air into and around the combustion chamber. This air is heated and provides a stream of clean, hot air.

Clean Heated Air Out (Front)

The Ignition System: The piezo ignitor lights

the burner.

The Automatic Control System: This system causes

the heater to shut down if the ﬂame goes out.

Fan

Motor

Cool Air In (Back)

Combustion Chamber

Figure 2 - Cross Section Operational View

PROPANE SUPPLY

Propane gas and propane tank(s) are to be furnished by the user.

Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the

Standard for Storage and Handling of Liqueﬁed Petroleum Gas, ANSI/NFPA 58 B149.2. Your local library or ﬁre department will

have this booklet. The amount of propane gas ready for use from

propane tanks varies. Two factors decide this amount:

1. The amount of propane gas in tank(s)

2. The temperature of tank(s) This heater is designed to operate with a minimum

20 pound (9 kg) propane tank. You may need two or more tanks or one larger tank in colder weather. It is recommended you use a 100 pound (45 kg) tank for longer operation. See chart below. Less gas is vaporized at lower temperatures. Your local propane gas dealer will help you select the proper supply system. The minimum surrounding air tem perature rating for each heater is 0° F (-18° C).

Average Temp No. Of Tanks At Tank Location 100-pound (45 kg)

Above 0° F (-18° C) 1 Below 0° F (-18° C) 2

and/or CAN/CGA

Hose/Regulator Assembly

INSTALLATION

WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater.

WARNING: Test all gas piping and connections for leaks after installation or servicing. Never use an open ﬂame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.

1. Provide propane supply system (see Propane Supply).

2. Connect POL ﬁtting on hose/regulator as sembly to propane tank(s). Turn POL ﬁtting counterclockwise into threads on tank. Tighten ﬁrmly using wrench. IMPORTANT: Position regulator so that hose leaving the regulator is in a horizontal position (see Figure 3, page 5). This places the regulator vent in the proper position to protect it from the weather.

www.desatech.com

113855-01B

INSTALLATION

Continued

3. Connect hose to valve inlet (see Figure 4). Tighten ﬁrmly using a wrench.

IMPORTANT: Use extra hose or piping if

needed. Install extra hose or piping between hose/regulator assembly and propane tank. You must use the regulator supplied with heater.

4. Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess-ﬂow check valve on propane tank will stop gas ﬂow. You may hear a click from the excess-ﬂow check valve closing. If this happens, reset the excess-ﬂow check valve by closing propane supply valve and open again slowly.

5. Check all connections for leaks. Apply mix ture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected.

6. Close propane supply valve.

Propane Supply Valve

Propane Tank

Figure 3 - Regulator Position

Inlet Connector

Figure 4 - Hose and Inlet Connector

Hose

Regulator

POL Fitting

Hose

VENTILATION

WARNING: Provide at least a 1.5 ft2 (1400 cm2) opening of fresh, outside air while running heater. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater.

OPERATION

WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater.

TO START HEATER

1. Follow all installation, ventilation and safety information.

2. Locate heater on stable and level surface. Make sure strong drafts do not blow into front or rear of heater.

3. Plug power cord of heater into a three-prong, grounded extension cord. Extension cord must be at least six feet long. Extension cord must be UL listed.

Extension Cord Wire Size Requirements Up to 50 ft (15.24 m) long, use 18 AWG rated

cord.

51 to 100 ft (15.54 to 30.48 m) long, use 16

AWG rated cord.

101 to 200 ft (30.78 to 60.96 m) long, use 14

AWG rated cord.

4. Plug extension cord into a 120 volt/60 hertz, 3-hole, grounded outlet. Motor will start. Fan will turn, forcing air out front of heater.

5. Open propane supply valve on propane tank(s) slowly. excess-ﬂow check valve on propane tank will stop gas ﬂow. You may hear a click from the excess-ﬂow check valve closing. If this happens, reset the excess-ﬂow check valve by closing propane supply valve and open again slowly.

Note: If not opened slowly,

113855-01B

www.desatech.com

OPERATION

Continued

WARNING: Be sure motor and fan are running before pushing in automatic control valve button. Flames could ﬂash outside heater if motor and fan are not running.

6. Push in and hold automatic control valve button (see Figure 5). Push piezo ignitor button (see Figure 5). Keep pushing ignitor button until the burner lights. When burner lights, keep automatic control valve button pushed in. Release button after 30 seconds. This activates the automatic control system.

Note: If heater fails to ignite, hose may have

air in it. If so, keep automatic control valve button pressed and wait 20 seconds. Release automatic control valve button and wait 20 seconds for unburned fuel to exit heater. Repeat this step.

NOTICE: If heater is unplugged or power outage occurs while heater is running, the thermal limit device will stop fuel ﬂow. A few seconds occur before the thermal limit device activates. During this short time, ﬂames may appear outside the heater. This is normal. The ﬂames will go out when thermal limit device activates.

TO STOP HEATER

1. Tightly close propane supply valve on propane tank(s).

2. Wait a few seconds. Heater will burn gas left in supply hose.

3. Unplug heater.

TO RESTART HEATER

1. Wait ﬁve minutes after stopping heater.

2. Repeat steps under To Start Heater

, page 5.

STORAGE

CAUTION: Disconnect heater

from propane supply tank(s).

1. Store propane tank(s) in safe manner. See Chapter 5 of Standard for Storage and Han

dling of Liqueﬁed Petroleum Gases, ANSI/ NFPA 58. Follow all local codes. Always store

propane tanks outdoors.

2. Place plastic cover caps over brass ﬁttings on inlet connector and hose/regulator assembly.

3. Store in dry, clean and safe place. Do not store hose/regulator assembly inside heater combustion chamber.

4. When taking heater out of storage, always check inside of heater. Insects and small animals may place foreign objects in heater. Remove motor and other internal parts if needed to remove foreign objects (see Service

Procedures,

page 7).

Piezo Ignitor

Automatic Control Valve Button

Figure 5 - Automatic Control Valve

Button and Piezo Ignitor

www.desatech.com

113855-01B

MAINTENANCE

WARNINGS

• Never service heater while it is plugged in, connected to propane supply, operating or hot. Severe burns and electrical shock can occur.

• Keep heater clear and free from combustible materials, gasoline and other ﬂammable vapors and liquids.

• Do not block the ﬂow of combustion or ventilation air.

1. Keep heater clean. Clean heater annually or as needed to remove dust and debris. If heater is dirty or dusty, clean heater with a damp cloth. Use household cleaners on difﬁcult spots.

2. Inspect heater before each use. Check connec tions for leaks. Apply mixture of liquid soap and water to connections. Bubbles forming show a leak. Correct all leaks at once.

3. Inspect hose/regulator assembly before each use. If hose is highly worn or cut, replace with hose speciﬁed by manufacturer.

4. Have heater inspected yearly by a qualiﬁed service agency.

5. Keep inside of heater free from combustible and foreign objects. Remove motor and other internal parts if needed to clean inside of heater (see Service Procedures).

6. Clean fan blades each season or as needed (see Fan, page 8).

SERVICE PROCEDURES

MOTOR

1. Remove three screws that attach fan guard to heater shell.

2. Remove motor and fan guard from heater shell (see Figure 6).

3. Use hex wrench to loosen set screw which holds fan to motor shaft (see Figure 7). Re move fan. Be careful not to damage the fan blade pitch.

4. Remove two nuts and two screws that attach fan guard to motor using nut-driver. Remove fan guard from motor (see Figure 8).

Motor and Fan Guard

Screw

Figure 6 - Removing Motor and Fan

Guard from Heater

Setscrew

WARNING: Never service heater while it is plugged in, connected to propane supply, operating or hot. Severe burns and electrical shock can occur.

ELECTRICAL SYSTEM

The entire electrical system for this heater is contained within the motor. If any part of the electrical system is damaged, you must replace motor.

113855-01B

www.desatech.com

Figure 7 - Setscrew Location

Fan Guard

Screw

Motor

Figure 8 - Removing or Attaching Fan

Guard from Motor

SERVICE PROCEDURES

Continued

Disconnect the green power cord wire from motor

and remove black and white wire terminals.

6. Discard old motor.

7. Attach green power cord wire to motor.

8. Attach fan guard to new motor with two nuts and two screws.

9. Replace black and white terminals.

10. Place fan onto motor shaft of new motor. Make sure set screw contacts ﬂat surface on motor shaft. Tighten set screw ﬁrmly (40-50 inchpounds [46.08-57.60 kilogram-centimeters]).

11. Place motor and fan guard into rear of heater shell. Make sure power cord is properly lo cated (see Figure 9).

12. Insert three screws through heater shell and into fan guard (see Figure 9). Tighten screws ﬁrmly.

Motor and Fan Guard

Screw

6. Dry fan thoroughly.

7. Place fan onto motor shaft. Make sure set screw contacts ﬂat surface on motor shaft. Tighten set screw ﬁrmly (40-50 inch-pounds [46.08-57.60 kilogram-centimeters]).

8. Place motor and fan guard into rear of heater shell. Make sure power cord is properly lo cated (see Figure 9).

9. Insert three screws through heater shell and into fan guard. Tighten screws ﬁrmly.

IGNITOR

1. Remove motor and fan guard from heater (see Motor, page 7, steps 1 and 2).

2. Remove black ignitor wire from piezo ignitor. Access ignitor wire through underside of

heater base (see Figure 10). Push wire up

through notch in ﬁller panel.

3. Remove ignitor mounting screw from rear head using nut-driver or standard screwdriver (see Figure 11).

4. Remove ignitor from rear head.

Piezo Ignitor

Screw

Figure 9 - Replacing Motor and Fan

Guard Into Heater

FAN

1. Remove three screws that attach fan guard to heater shell.

2. Remove motor and fan guard from heater shell (see Figure 6, page 7).

3. Use hex wrench to loosen set screw that holds fan to motor shaft (see Figure 7, page 7).

4. Remove fan. Be careful not to damage the fan blade pitch.

5a. If replacing fan, remove old fan and discard.

Go to step 7, column 2.

5b. If cleaning fan, use soft cloth moistened with

kerosene or solvent.

www.desatech.com

Ignitor Wire

Figure 10 - Removing Ignitor Wire from

Piezo Ignitor

Ignitor

Figure 11 - Removing Ignitor Mounting

Screw and Ignitor

Underside of Heater

Mounting Screw

113855-01B

SERVICE PROCEDURES

Continued

5. Install new ignitor. Attach ignitor to rear head with ignitor mounting screw.

6. Run ignitor wire from new ignitor through notch in ﬁller panel. Attach ignitor wire to piezo ignitor.

7. Set gap between ignitor electrode and target plate to 0.17" (43.18 cm) (see Figure 12).

9. Place motor and fan guard into rear of heater shell (see Motor, page 8, steps 9 and 10).

Ignitor Electrode

Gap Area

WARNING: Make sure heater is disconnected from propane supply. Heater could ignite causing severe burns.

8. Test for spark. Push piezo ignitor button and watch for spark between ignitor electrode and target plate.

Figure 12 - Clearance Between Ignitor

Electrode and Target Plate

SPECIFICATIONS

35-FAC, NLP35A, RLLP35A, SPC-35

• 35,000 BTU/Hr Output Rating

• Fuel - Propane Vapor

• Fuel Consumption

Gallons (liters)/Hour - 0.38 (1.44) Pounds (kg)/Hour - 1.62 (0.74)

• Supply Pressure To Regulator

Minimum* - 20 psi, Maximum - Tank Pressure

or 200 psi

• Regulator Outlet Pressure - 10 PSI

• Manifold Pressure - 10 PSI

• Hot Air Output (CFM Approx) - 100

• Motor - 3045 RPM, 1/40 HP

• Electric Input - 120 volt/60 hertz

• Amperage - .6

• Ignition - Manual, Piezo

• Temperature Range for Heater Operation

0° F to 85° F** (-17° C to 29.4° C)**

• Heater Weight - 14 lbs. (6.35 kg)

• Shipping Weight - 15.3 lbs. (6.94 kg)

• Carton Size (L x W x H)

19.75" x 11.25" x 14" (50.2 x 28.6 x 35.6 cm)

• Heater Size (L x W x H)

18.5" x 7.7" x 12.8" (47 x 19.6 x 32.5 cm)

* For purposes of input adjustment ** When running heater in temperatures above 85° F (29.44° C), high internal temperatures may cause thermal limit

device to shut down heater.

SPC-40

• 40,000 BTU/Hr Output Rating

• Fuel - Propane Vapor

• Fuel Consumption Gallons (liters)/Hour - 0.44 (1.65) Pounds (kg)/Hour - 1.86 (0.84)

• Supply Pressure To Regulator Minimum* - 20 psi, Maximum - Tank Pressure

or 200 psi

• Regulator Outlet Pressure - 10 PSI

• Manifold Pressure - 10 PSI

• Hot Air Output (CFM Approx) - 100

• Motor - 3045 RPM, 1/40 HP

• Electric Input - 120 volt/60 hertz

• Amperage - .6

• Ignition - Manual, Piezo

• Temperature Range for Heater Operation 0° F to 85° F** (-17° C to 29.4° C)**

• Heater Weight - 14 lbs. (6.35 kg)

• Shipping Weight - 15.3 lbs. (6.94 kg)

• Carton Size (L x W x H)

19.75" x 11.25" x 14" (50.2 x 28.6 x 35.6 cm)

• Heater Size (L x W x H)

18.5" x 7.7" x 12.8" (47 x 19.6 x 32.5 cm)

113855-01B

www.desatech.com

TROUBLESHOOTING

WARNING: Never service heater while it is plugged in, connected to propane supply, operating or hot. Severe burns and electrical shock can occur.

OBSERVED FAULT

Fan does not turn when heater is plugged in

Heater will not ignite

Heater shuts down while running

POSSIBLE CAUSE

1. No electrical power to heater

2. Fan hitting inside of heater shell

3. Fan blades bent

4. Defective motor

1. User did not follow installa tion or operation instructions properly

2. No spark at ignitor. To test for spark, follow step 8 under nitor, page 9. If you see spark at ignitor, have heater serviced by qualiﬁed service person. If no spark seen:

A) Loose or disconnected

ignitor wire

B) Wrong spark gap C) Piezo ignitor loose D) Bad ignitor electrode

1. High surrounding air tem perature causing thermal limit device to shut down heater

2. Restricted air ﬂow

3. Damaged fan

4. Excessive dust or debris in surrounding area

Ig-

REMEDY

1. Check voltage to electrical outlet. If voltage is good, check heater power cord for breaks

2. Adjust motor/fan guard to keep fan from hitting inside of heater shell. Bend fan guard if necessary

3. Replace fan. See

4. Replace motor. See Motor page 7

1. Repeat installation and opera

tion instructions. See Installa tion and Operation, page 5

2. A) Check ignitor wire. Tighten or reattach loose ignitor wire. See Figure 11, page 8 for ignitor wire location

B) Set gap between ignitor

electrode and target plate to .17" (0.43 cm)

C) Tighten nut holding piezo

ignitor to base of heater

D) Replace ignitor electrode.

See Ignitor, page 8

1. This can happen when running

heater in temperatures above 85°F (29.44° C). Run heater in cooler temperatures

2 Check heater inlet and outlet.

Remove any obstructions

3. Replace fan. See

4. Clean heater. See Mainte

nance, page 7

Fan, page 8

WARNING: Use only in areas

free of high dust content.

www.desatech.com

113855-01B

ACCESSORIES

Purchase accessories and parts from your nearest dealer or service center. If your dealer or service center can not supply an accessory or part, either contact your nearest Parts Central (listed in the separate Authorized Service Center booklet) or call DESA Heating Products at 1-866-672-6040 for referral information. You can also write to the address listed on the back page of this manual.

TECHNICAL SERVICES

You may have further questions about this heater. If so, contact DESA Heating Productsʼ Technical Service Department at 1-866-672-6040. When calling, please have your model and serial numbers of your heater ready.

You can also visit DESA Heating Productsʼ Techni cal Service web site at www.desatech.com.

REPLACEMENT PARTS

WARNING: Use only original replacement parts. This heater must use design-speciﬁc parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries. This will also protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they canʼt supply original replacement part(s), either

contact your nearest Parts Central or call DESA

Heating Productsʼ Technical Service Department at 1-866-672-6040.

When calling DESA Heating Products, have ready

• your name

• your address

• model number of your heater

• how heater was malfunctioning

• purchase date

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they canʼt supply original replacement part(s), either contact your nearest Parts Central (listed in Authorized Service Center booklet) or call DESA Heating Products at 1-866-672-6040 for referral information.

When calling DESA Heating Products, have ready

• model number of your heater

• the replacement part number

113855-01B 11

www.desatech.com

ILLUSTRATED PARTS BREAKDOWN

MODELS 35-FAC, NLP35A, RLLP35A, SPC-35 AND SPC-40

www.desatech.com

113855-01B

PARTS LIST

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 11 of this manual.

KEY NO. PART NO. DESCRIPTION QTY.

1 113832-01 Heater Body Kit (Replacement kit will be unpainted) • • • • • 1 2 113833-01 Control Box Assembly • • • • • 1 3 102445-01 Piezo Ignitor • • • • • 1 4 102334-01 Palnut Fastner • • • • • 1 5 113852-01 Hex Nut, 5-28 • • • • • 1 6 113834-01 Valve with Thermocouple Assembly • • • • 1

113834-02 Valve with Thermocouple Assembly • 1 7 113846-01 Wire Assembly • • • • • 1 8 115324-01 Thermal Switch Kit • • • • • 1 9 113847-01 Electrode Ignitor • • • • • 1 10 097918-01 Handle Clip • • • • • 2

097917-01 Handle • • • • • 1

11 12 113851-01 Fan • • • • • 1 13 113849-01 Motor Assembly • • • • • 1 14 113850-01 Fan Guard • • • • • 1 15 M11143-1 Bushing, Strain Relief • • • • • 1 16 098219-25 Cord, Power Supply • • • • • 1

PARTS AVAILABLE - NOT SHOWN

113835-01 Hose/Regulator Assembly • • • • • 1

113858-01 Tradename Decal (SPC-35, SPC-40)

113858-02 Tradename Decal (35-FAC)

113858-04 Tradename Decal (NLP35A)

109111-02 Tradename Decal (RLLP35A)

113853-01 Warning Decal

113854-01

113802-03

113802-04

Operation Decal • • • • • 1 Model Data Decal • • • • 1 Model Data Decal • 1

** Not a ﬁeld replaceable part.

35-FAC

SPC-35

NLP35A

RLLP35A

SPC-40

• • 2

• 2

• • • • • 1

113855-01B

www.desatech.com

WARRANTY AND REPAIR SERVICE

KEEP THIS WARRANTY

Model

Serial No.

Date of Purchase

LIMITED WARRANTIES FOR NEW AND FACTORY

RECONDITIONED PRODUCTS

New Products: DESA Heating Products warrants this heater and any parts thereof, to be free of defects in materials

and workmanship for one (1) year from the date of ﬁrst purchase, when operated and maintained in accordance with the manufacturer's instructions. These warranties are extended only to the original retail purchaser, when proof of purchase is provided.

Factory Reconditioned Heaters: DESA Heating Products warrants this factory reconditioned heater and any parts

thereof, to be free of defects in materials and workmanship for thirty (30) days from the date of ﬁrst purchase, when operated and maintained in accordance with the manufacturer's instructions. These warranties are extended only to the original retail purchaser, when proof of purchase is provided.

These warranties cover only the cost of parts and labor required to restore the product to proper operating condition. Transportation and incidental costs associated with warranty repairs are not reimbursable under this warranty.

Warranty service is available only through authorized dealers and service centers. This warranty does not cover defects resulting from misuse, abuse, negligence, accidents, lack of proper mainte

nance, normal wear, alteration, modiﬁcation, tampering, contaminated fuels, repair using improper parts or repair by anyone other than an authorized dealer or service center. Routine maintenance is the responsibility of the owner.

THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

DESA Heating Products assumes no responsibility for indirect, incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations or exclusions may not apply to you. This limited warranty gives you speciﬁc legal rights and you may also have other rights which vary from state to state.

We reserve the right to amend these speciﬁcations at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.

WARRANTY SERVICE

Should your heater require service, return it to your nearest authorized service center. Proof of purchase must be presented with the heater. The heater will be inspected. A defect may be caused by faulty materials or workman ship. If so, DESA Heating Products will repair or replace the heater without charge.

REPAIR SERVICE

Return your heater to your nearest authorized service center. Repairs not covered by the warranty will be billed at standard prices. Each Service Center is independently owned and operated. We reserve the right to amend these speciﬁcations at any time without notice. When writing, always include model number and serial number. For information, write:

2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 ATTN: Customer Service Department

+ 30 hidden pages