Desa Tech CF26PR, NMCF26PT Owner's Manual

Download

Page 1

For more information, visit www.desatech.com

CF26PR

19,000 to 26,000 Btu/Hr

Remote Control Ready

UNVENTED (VENT-FREE) GAS BAY FRONT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

Patent Pending

Fireplace Shown

A U T O

O F F

O N

With Optional

Bay Front Mantel

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed by a

qualified installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to

Combustion and Ventilation

Air for

sec-

tion on page 4 of this manual.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

Page 2

TABLE OF CONTENTS SAFETY INFORMATION

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................ 2

PRODUCT IDENTIFICATION ..................................................... 3

LOCAL CODES........................................................................... 3

UNPACKING............................................................................... 4

PRODUCT FEATURES .............................................................. 4

REMOTE CONTROL ACCESSORIES ....................................... 4

AIR FOR COMBUSTION AND VENTILATION ........................... 4

INSTALLATION ........................................................................... 6

OPERATING FIREPLACE ........................................................ 16

INSPECTING BURNERS.......................................................... 19

CLEANING AND MAINTENANCE ............................................ 19

SAFETY INFORMATION

WARNINGS

WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects, or other reproductive harm.

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.

DANGER: Carbon monoxide poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon monoxide

poisoning resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.

Propane/LP Gas: Propane/LP gas is odorless. An odor-making

agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.

WARNING: Any change to this heater or its controls can be dangerous.

SPECIFICATIONS .................................................................... 20

WIRING DIAGRAM ................................................................... 20

TROUBLESHOOTING .............................................................. 21

ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 24

REPLACEMENT PARTS .......................................................... 28

PARTS CENTRALS .................................................................. 28

TECHNICAL SERVICE ............................................................. 28

SERVICE HINTS....................................................................... 28

OWNER’S REGISTRATION FORM.......................................... 29

ACCESSORIES ........................................................................ 31

WARRANTY INFORMATION...................................... Back Cover

WARNING: Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this heater.

WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

Do not place clothing or other flammable material on or near the appliance. Never place any objects in the fireplace or on logs.

Fireplace front and screen become very hot when running fireplace. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young children when they are in the room with fireplace. When using the hand-held remote accessory, keep selector switch in the OFF position to prevent children from turning on burners with remote.

You must operate this fireplace with a fireplace screen in place. Make sure fireplace screen is closed before running heater.

For more information, visit www.desatech.com

105442-01E

Page 3

SAFETY INFORMATION

Continued

SAFETY INFORMATION

PRODUCT IDENTIFICATION

LOCAL CODES

Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in

your building

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions

• if you cannot reach your gas supplier , call the fire department

4. This fireplace shall not be installed in a bedroom or bathroom.

5. Do not use this fireplace as a wood-burning fireplace. Use only the logs provided with the fireplace.

6. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of fireplace.

7. This fireplace is designed to be smokeless. If logs ever appear to smoke, turn off fireplace and call a qualified service person.

Note:

During initial operation, slight smoking could occur due

to log curing and fireplace burning manufacturing residues.

8. To prevent the creation of soot, follow the instructions in Clean- ing and Maintenance, pages 19 and 20.

9. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

10. This fireplace needs fresh air ventilation to run properly. This fireplace has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the fireplace if not enough fresh air is available. See Air for Combustion and Ventilation, pages 4 through 6. If fireplace keeps shutting off, see Trouble- shooting, pages 21 through 23.

11. Do not run fireplace

• where flammable liquids or vapors are used or stored.

• under dusty conditions.

12. Do not use this fireplace to cook food or to burn paper or other solid fuels.

13. Do not use fireplace if any part has been under water . Immediately call a qualified service technician to inspect the room fireplace and to replace any part of the control system and any gas control which has been under water.

14. Turn off and unplug fireplace and let cool before servicing. Only a qualified service person should service and repair fireplace.

15. Operating fireplace above elevations of 4,500 feet could cause pilot outage.

16. Do not operate fireplace if any log is broken. Do not operate fireplace if a log is chipped (dime-sized or larger).

17. T o prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

18. Provide adequate clearances around air openings.

PRODUCT IDENTIFICATION

Screen

Fireplace Cabinet

Brick Liner

Logs

A U T O

O F F

O N

Heater Controls (Inside Door)

Figure 1 - Vent-Free Propane/LP Gas Compact Fireplace

LOCAL CODES

Install and use fireplace with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code,

ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

105442-01E

For more information, visit www.desatech.com

Page 4

UNPACKING PRODUCT FEATURES

REMOTE CONTROL ACCESSORIES AIR FOR COMBUSTION AND VENTILATION

Providing Adequate Ventilation

UNPACKING

1. Remove and fireplace from carton.

2. Remove all protective packaging applied to fireplace for shipment.

3. Make sure your fireplace includes one hardware packet.

4. Check fireplace for any shipping damage. If fireplace is damaged, promptly inform dealer where you bought fireplace.

PRODUCT FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for ventfree room fireplaces. The ODS/pilot shuts off the fireplace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This system requires no matches, batteries, or other sources to light fireplace.

REMOTE CONTROL ACCESSORIES

There are two optional remote controls that can be purchased separately for this log heater:

• hand-held ON/OFF remote

• hand-held thermostat remote

See Accessories, page 31.

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuelburning appliances in your home.

Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54 Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space The information on pages 4 through 6 will help you classify your

space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a. walls and ceilings e xposed to the outside atmosphere

have a continuous water vapor retarder with a rating of one perm (6 x 10 openings gasketed or sealed

b. weather stripping has been added on openable win-

dows and doors

For more information, visit www.desatech.com

-11

kg per pa-sec-m2) or less with

and

105442-01E

Page 5

AIR FOR COMBUSTION AND VENTILATION

Continued

AIR FOR COMBUSTION AND VENTILATION

Providing Adequate Ventilation (Cont.)

Determining Fresh-Air Flow For Fireplace Location

c. caulking or sealants are applied to areas such as

joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations f or plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air. See

From Outdoors

, page 6

Ventilation Air

If your home does not meet all of the three criteria above, proceed to

Location,

Determining Fresh-Air Flow For Fireplace

below

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfining space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space. Space: Includes the room in which you will install heater plus any adjoining

rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x width x height). Length x Width x Height =___________ cu. ft. (volume of space)

Example:

height) = 2560 cu. ft. (volume of space) If additional ventilation to adjoining room is supplied with grills or open-

ings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maximum Btu/Hr the space

Example:

Btu/Hr the space can support)

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling

can support)

2560 cu. ft. (volume of space) x 20 = 51,200 (maximum

3. Add the Btu/Hr of all fuel burning appliances in the space. Vent-free heater _____________ Btu/Hr Gas water heater* _____________ Btu/Hr Gas furnace _____________ Btu/Hr Vented gas heater _____________ Btu/Hr Gas fireplace logs _____________ Btu/Hr Other gas appliances* + _____________ Btu/Hr Total = _____________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

Gas water heater _____________ Btu/Hr Vent-free heater + _____________ Btu/Hr Total = _____________ Btu/Hr

4. Compare the maximum Btu/Hr the space can support with the actual

amount of Btu/Hr used.

__________________ Btu/Hr (maximum the space can support) __________________ Btu/Hr (actual amount of Btu/Hr used)

Example:

The space in the example above is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the

extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See V entilation Air Fr om Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Out-

doors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined. If the actual Btu/Hr used is less than the maximum Btu/Hr the space can

support, the space is an unconfined space. You will need no additional fresh air ventilation.

51,200 Btu/Hr (maximum the space can support) 56,000 Btu/Hr (actual amount of Btu/Hr used)

30,000 26,000 56,000

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the

National Fuel Gas Code, ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

105442-01E

For more information, visit www.desatech.com

Page 6

Outlet Air

Ventilated Attic

Outlet Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

AIR FOR COMBUSTION AND VENTILATION

Ventilation Air

INSTALLATION

Check Gas Type

AIR FOR COMBUSTION AND VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel

Gas Code ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code ANSI Z223.1/ NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

IMPORTANT:

attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent.

Do not provide openings for inlet or outlet air into

12"

Figure 3 - Ventilation Air from Outdoors Shown with Optional Mantel

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

Ventilation Grills

Ventilation

Grills

into Adjoining

Room,

Option 1

Figure 2 - Ventilation Air from Inside Building Shown with Optional Mantel

Remove

Door into

Adjoining

Room,

Option 3

Into Adjoining Room,

Option 2

12"

For more information, visit www.desatech.com

WARNING: A qualified service person must install fireplace. Follow all local codes.

Note:

Your Comfort Glow fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fireplace Installation, pages 7 and 8).

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply is not propane/LP, do not install fireplace. Call dealer where you bought fireplace for proper type fireplace.

105442-01E

Page 7

INSTALLATION

Continued

INSTALLATION

Locating Fireplace

Built-In Fireplace Installation

LOCATING FIREPLACE

WARNING: Maintain the minimum clearances shown in Figure 4. If you can, provide greater clearances from floor, ceiling, and joining wall.

You can recess firebox into the wall. You can also position fireplace in the optional cabinet mantels. cabinet mantels specified in this manual. Purchase the optional mantel from your dealer (see Accessories, page 31).

WARNING: Never install the fireplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture, clothing, or other flam-

mable objects are less than 42 inches from the front, top, or sides of the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: This fireplace creates warm air currents. These currents move heat to wall surfaces next to fireplace. Installing fireplace next to vinyl or cloth wall coverings or operating fireplace where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

MPORTANT:

Vent-free fireplaces add moisture to the air. Although this is beneficial, installing fireplace in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 through 6.

CAUTION: If you install the fireplace in a home

garage

• fireplace pilot and burner must be at least 18 inches above floor.

• locate fireplace where moving vehicle will not hit it.

For convenience and efficiency, install fireplace

• where there is easy access for operation, inspection, and service.

• in coldest part of room. An optional blower kit is available from your dealer. See Accesso-

ries, page 31. If planning to use blower, locate fireplace near an electrical outlet.

IMPORTANT:

Only use optional

Minimum Clearances For Side Combustible Material, Side Wall, and Ceiling

A. Clearances from the side of the fireplace cabinet to any com-

bustible material and wall should follow diagram in Figure 4.

Example:

The face of a mantel, bookshelf, etc. is made of combustible material and protrudes 3 1/2" from the wall. This combustible material must be 4" from the side of the fireplace opening (see Figure 4).

B. Clearances from the top of the fireplace opening to the ceiling

should not be less than 42 inches.

Example

*Minimum 16 inches from Side Wall

Figure 4 - Minimum Clearance for Combustible to Wall

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. Follow the instructions below to install the fireplace in this manner. If installing a built-in mantel above the fireplace, you must follow the clearances shown in Figure 8, page 9.

Note:

If desired, purchase a four-sided brass trim kit for built-in

installations. See Accessories, page 31.

Actual Framing

Height 26" 26

Front Width 26

Depth 9

Bottom 3/4" 3/4"

/4" 26 7/8"

/2" 10 1/2"

1. Frame in rough opening. Use dimensions shown in Figure 5, page 8, for the rough opening.

If installing in a corner, use dimensions shown in Figure 6, page 8, for the rough opening. The height is 26 1/8" which is the same as the wall opening above.

/8"

105442-01E

For more information, visit www.desatech.com

Page 8

INSTALLATION

Built-In Fireplace Installation (Cont.)

INSTALLATION

Continued

2. An optional blower accessory is available (see Accessories, page 31). There are two options for connecting blower to electrical source.

Option one: Have a licensed electrician install a properly

grounded, three-prong 120-volt electrical outlet at fireplace location. Locate outlet inside the framed enclosure. Blower power cord will plug into this outlet.

Option two: Have a licensed electrician connect blower to elec-

trical source at junction box inside fireplace. If using option one, have electrical outlet installed at this time.

If using option two, do not connect blower to electrical source at junction box until step 6.

3. Install gas piping to fireplace location. This installation includes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping.

4. Carefully set fireplace in front of rough opening with back of fireplace inside wall opening.

5. Attach flexible gas line to fireplace gas regulator. See Con- necting Fireplace to Gas Supply, page 13.

6. If the optional blower has been installed connect blower to electrical source.

Option one: Route blower electrical cord through side or rear

access door of fireplace. Plug electrical cord into electrical outlet.

Option two: Have a licensed electrician connect blower to elec-

trical source at junction box inside fireplace.

7. Bend four nailing flanges on outer casing with pliers (see Figure 7).

8. Attach fireplace to wall studs using nails or wood screws through holes in nailing flange.

9. Check all gas connections for leaks. See Checking Gas Con- nections, page 14.

IMPORTANT:

When finishing your firebox, combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top of the firebox. Combustible materials should never overlap the firebox front facing. Firebox should not be placed on top of carpet or other kinds of fibrous material.

WARNING: Do not allow any combustible materi-

als to overlap the firebox front facing.

IMPORTANT:

Noncombustible materials such as brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.

WARNING: Do not allow noncombustible materials

to cover any necessary openings like louvered slots.

WARNING: Never modify or cover the louvered

slots on the front of the firebox.

WARNING: Use only noncombustible mortar or adhesives when overlapping the front facing with noncombustible facing material.

3/4" Off

The Floor Minimum

Figure 5 - Rough Opening for Installing in Wall

Figure 6 - Rough Opening for Installing in Corner

For more information, visit www.desatech.com

Nails or Wood Screws

A U T O

O F F

O N

Nailing Flanges

Figure 7 - Attaching Fireplace to Wall Studs

105442-01E

Page 9

INSTALLATION

Continued

INSTALLATION

Mantel Clearances For Built-In Installation

Removing Brick Liner Retainer

Assembling Brass Trim

Optional Mantel Installation

MANTEL CLEARANCES FOR BUILT-IN INSTALLATION

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

• raise the mantel to an acceptable height

• remove the mantel

Mantel Shelf

Note:

All vertical measurements are from top of fireplace opening to bottom of mantel shelf.

Minimum NonCombustible Material

Figure 8 - Minimum Mantel Clearances for Built-In Installation

10" 8" 6" 2 1/2"

13"

16"

19"

21"

ASSEMBLING BRASS TRIM

(Brass trim shipped with mantel)

1. Remove packaging from three pieces of brass trim.

2. Locate two adjusting plates with set screws, and two shims in the hardware packet.

3. Align shim under adjusting plate as shown in Figure 9.

4. Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 9).

5. Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 9).

6. While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set brass assembly aside for later installation.

Slot

Shim

Mitered Edge

Top Brass Trim

Side Brass Trim

Set Screws

Adjusting Plate

Figure 9 - Assembling Brass Trim

OPTIONAL MANTEL INSTALLATION

Note:

Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installation. If using blower accessory (see Accessories, page 31), see installation instructions on pages 10 and 11.

1. Choose location for fireplace and install gas supply line.

2. Remove screen from fireplace by removing screws in each

end of screen rod (see Figure 10). Hold screen rod cover while removing five hex head screws underneath hood (see Figure 11, page 10). Carefully lift and pull out hood (see Figure 12, page 10).

REMOVING BRICK LINER RETAINER

1. Using Phillips screw driver, remove 2 screws attaching brick liner retainers to vertical sides.

2. Remove brick liner retainers and discard. Replace 2 screws into vertical sides.

For more information, visit www.desatech.com

105442-01E

Figure 10 - Removing Screen

Page 10

INSTALLATION

Optional Mantel Installation (Cont.) Installing Blower Assembly - GA3450T

INSTALLATION

Continued

3. Assemble brass trim kit. See Assembling Brass Trim, column 2.

4. Place brass trim on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 13).

5. Place mantel base close to wall in desired fireplace location.

6. Install gas line. See Connecting To Gas Supply, page 12

7. Carefully place fireplace on mantel base and center left to right. Check for gas leaks. See Checking Gas Connections, page 14.

8. Refer to instructions provided with the mantel for permanent attachment to wall.

9. Slide mantel around fireplace. Be careful not to damage wall or mantel.

10. Adjust assembly to remove any gaps. From back side of fireplace, attach two 2" wood screws through base mounting blocks attached to bottom sides of mantel into base (see instructions provided with mantel).

11. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. See Figure 12, for screw hole location.

Hood

Screen Rod Cover

Screw

Figure 11 - Removing Hood Screws

Mantel Screw Location

Figure 12 - Removing Hood

Shoulder Screws

INSTALLING BLOWER ASSEMBLY - GA3450T

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

CAUTION: Verify proper operation after servicing.

Note:

If you are using a mantel with your heater, use the following

instructions. If your heater is built-in, see For Built-In Installation on page 11.

1. Screen and hood should be removed from fireplace (see page

9). Remove log set and set aside.

2. Install snap bushings found in hardware kit into both holes in rear of blower control shield (see Figure 14).

3. Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly.

4. Note the wire locations on back of AUTO/OFF/ON switch. Carefully remove red wire from the AUTO terminal and blue wire from the ON terminal. Black wire can remain on the middle or OFF terminal (see Figure 15, page 11).

5. Carefully disconnect green and white wires from power cord harness at their insulated connectors.

6. In top of the heater cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket assembly to the outer casing with 4 - #10 screws provided (see Figure 15, page 11).

7. Route the wire harness through the hole to the left side of heat deflector. Pull wire harness through lower opening to the left of the blower control shield. (see Figure 15, page 11).

8. Insert the 4 wire harness into one of the round holes in the rear of the blower control shield and through the rectangular hole in the front of shield (see Figure 15, page 11).

9. Reconnect red wire to the AUTO switch position. Reconnect blue wire to the ON switch position. Reconnect green and white wires to the power cord.

Blower Control Shield

Snap Bushing

A U T O

O F F

O N

Assembled Brass Trim

Figure 13 - Attaching Brass Trim to Fireplace

For more information, visit www.desatech.com

Figure 14 - Installing Snap Bushings

105442-01E

Page 11

INSTALLATION

Continued

INSTALLATION

Installing Blower Assembly - GA3450T (Cont.)

10. Install the switch plate on the blower control shield with 2 #10 screws provided (see Figure 16). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 15). Plug fan kit into 120-Volt grounded power supply and test operation.

Note:

When switch is in the AUTO position, the fan will start after the heater has run for a few moments. The fan will continue to run for several moments after the heater has been turned off. When switch is in the ON position, the fan will run until turned to OFF . Reinstall hood assembly and close lower louver door.

11. Place log set back on the unit.

Wiring

Blower Bracket Assembly

Screw

Switch

Switch Plate

Blower Control Shield

Wire Harness Power Cord

Red

Blue

Wire Harness

Routing Hole

A U T

O F

O N

Heat Deflector

For Built-In Installation

WARNING: A licensed electrician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of heater.

WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.

1. Install a snap bushing found in hardware kit into one of the holes found on rear of blower control shield. The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2. Follow steps 2 through 6 in Installing Blower Assembly, page

10. Also remove black wire from middle/OFF switch terminal.

3. Remove black plastic strain relief and power cord from switch plate (see Figure 17). The power cord supplied will not be used in built-in installations. Pop in the plastic snap bushing found in hardware kit into the hole left by supply cord/strain relief.

Blower Bracket Assembly

Shield Cover

Figure 15 - Installing Blower Bracket Assembly

Blower Control Shield

Switch Plate

Screw

Figure 16 - Installing Switch Plate to Blower Control Shield

For more information, visit www.desatech.com

105442-01E

Screw

Switch

Strain Relief

Wire Harness

Power Cord

Blue

Red

Outlet Receptacle

Switch Plate

Shield Cover

Blower Control Shield

Clamp Connector (not included)

Wire Harness

Figure 17 - Installing Blower Bracket Assembly

A U T

O FF

Page 12

INSTALLATION

Installing Blower Assembly - GA3450T (Cont.) Connecting To Gas Supply

INSTALLATION

Continued

4. A licensed electrician must follow the wiring diagram in Figure 18 to connect incoming electrical supply to fan kit wiring harness.

5. Test to make sure the blower is working properly.

6. Reinstall hood assembly (see page 9) and close lower louver door.

7. Place log set back on the unit.

W ARNING: Never attempt to service heater while it is plugged in, operating, or hot. Burns and electrical shock could result. Only a qualified service person should service or repair heater.

If any of the original wire as supplied with the appliance must be replaced, original replacements must be used. DESA part no. 104015-01 (105°C) for power cord, and DESA part no. 10396801 (200°C) for wire harness.

WARNING: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

Fan Switch

(Auto/Off/On)

Auto

Off

Black Green White

Red

110/115

V.A.C.

120 Vac. 60 Hz. .30 Amps DESA International, Bowling Green, KY

Blue

Thermostat

Switch (N.O.)

Blue

Red

White Green

Blower

Motor

101584-06

Figure 18 - Wiring Diagram For Fan Accessory Built-In Installation

CONNECTING TO GAS SUPPLY

WARNING: A qualified service person must con-

nect fireplace to gas supply. Follow all local codes.

* A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 31.

The installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pressure, fireplace regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 19. Pointing the vent down protects it from freezing rain or sleet.

CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" or greater diameter to allow proper gas volume to fireplace. If pipe is too small, undue loss of volume will occur.

Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from fireplace (see Figure 20, page 13).

IMPORTANT:

Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged fireplace valves.

CAUTION: Never connect fireplace directly to the propane/LP supply. This fireplace requires an external regulator (not supplied). Install the external regulator between the fireplace and propane/LP supply.

Installation Items

Before installing fireplace, make sure you have the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• test gauge connection*

For more information, visit www.desatech.com

WARNING: Use pipe joint sealant that is resistant

to liquid petroleum (LP) gas.

Propane/LP Supply Tank

Figure 19 - External Regulator with Vent Pointing Down

External Regulator

Vent Pointing Down

105442-01E

Page 13

INSTALLATION

Continued

INSTALLATION

Connecting To Gas Supply (Cont.)

Connecting Fireplace To Gas Supply

We recommend that you install a sediment trap in supply line as shown in Figure 20 . Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into fireplace controls. If sediment trap is not installed or is installed wrong, fireplace may not run properly.

Gas Control

Approved Flexible Gas Hose

Figure 20 - Gas Connection

3" Minimum

CSA Design-Certified Equipment Shutoff Valve With 1/8" NPT Tap*

From External Regulator (11" W.C.** to 14" W.C. Pressure)

Cap Pipe Tee

Nipple Joint

Sediment Trap

* Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 31. ** Minimum inlet pressure for purpose of input adjustment.

2. Apply pipe joint sealant lightly to male threads of gas connector attached to flexible gas line (see Figure 22). Connect flexible gas line to flexible gas line attached to gas valve of fireplace (see Figure 22).

3. Check all gas connections for leaks. See Checking Gas Con- nections, page 14.

4. Feed flexible gas line into fireplace base area. Make sure the entire flexible gas line is in fireplace mantel base area.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.

Outer Casing

Equipment Shut Off

A U T O

O F F

O N

Valve

CONNECTING FIREPLACE TO GAS SUPPLY

Installation Items Needed

• Phillips screwdriver

• sealant (resistant to propane/LP gas, not provided)

1. Route flexible gas line (provided by installer) from equipment shutoff valve into fireplace through side or rear access holes in outer casing (see Figure 21).

NOTICE: Most building codes do not permit concealed gas connections. A flexible gas line is provided to allow accessibility from the fireplace (see Figure 22). The flexible gas supply line connection to the equipment shutoff valve should be accessible.

For more information, visit www.desatech.com

105442-01E

Figure 21 - Routing Flexible Gas Line

Equipment Shutoff Valve

➞

To External Regulator

Flexible Gas Line from Equipment Shutoff Valve Provided by Installer

Gas Connector

Flexible Gas Line from Fireplace Gas Valve Provided with Fireplace

Figure 22 - Attaching Flexible Gas Lines Together

To Fireplace Gas Valve

➞

Page 14

INSTALLATION

Checking Gas Connections

INSTALLATION

Continued

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

CAUTION: Make sure external regulator has been installed between propane/LP supply and fireplace. See guidelines under

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage fireplace regulator.

2. Cap off open end of gas pipe where equipment shutoff valve was connected.

3. Pressurize supply piping system by either using compressed air or opening propane/LP supply tank valve.

4. Check all joints of gas supply piping system. Apply a noncor rosive leak detection fluid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 23).

2. Pressurize supply piping system by either using compressed air or opening propane/LP supply tank valve.

3. Check all joints from propane/LP supply tank to equipment shutoff valve (see Figure 24). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Connecting to Gas Supply

, page 12.

Pressure Testing Fireplace Gas Connections

1. Open equipment shutoff valve (see Figure 23).

2. Open propane/LP supply tank valve.

3. Make sure control knob of fireplace is in the OFF position.

4. Check all joints from equipment shutoff valve to thermostat gas valve (see Figure 22, page 13). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light fireplace (see Operating Fireplace, pages 16 through

18). Check all other internal joints for leaks.

7. Turn off fireplace (see To Turn Off Gas to Appliance, page 17).

8. Replace front panel.

Open

Equipment Shutoff Valve

Figure 23 - Equipment Shutoff Valve

Figure 24 - Checking Gas Joints (Shown with Optional Mantel)

POSI

Closed

Equipment Shutoff Valve

Propane/LP

Supply Tank

For more information, visit www.desatech.com

105442-01E

Page 15

INSTALLATION

Continued

INSTALLATION

Installing Logs

Optional Wireless Hand-Held Remote Control Accessories

INSTALLING LOGS

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HI, check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

It is very important to install the logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

Place one-piece log set on grate to fit as illustrated in Figure 25. Make sure back section of log set is seated into “U”-shaped cutout in center of chassis (see Figure 25). does not cover any burner ports (see Figure 26).

IMPORTANT:

One Piece Log Set

Make sure log

OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES

(CGHRC & CGHRCT Series) Installing Receiver

1. Disconnect switch wires from the control valve.

2. Remove screws and nuts.

3. Remove switch plate (see Figure 27). Discard after removing.

4. Install remote receiver unit onto gas log heater base using clips (2) and insulating washers provided.

5. Push clips firmly into place (see Figure 28).

6. Connect wires as shown in Figure 29.

Front

Screw

Back

Nut

Figure 27 - Switch Plate and Wiring Harness (Switch Plate and Orientation May Vary Depending On Model)

Front

Wires

Burner

"U"-shaped Cutout in Chassis

Chassis

U T O

F F

Figure 25 - Installing One-Piece Log Set

Burner Ports

One Piece Log Set

Figure 26 - Installing One-Piece Log set (Top View)

For more information, visit www.desatech.com

105442-01E

Mounting Clips

Insulating Washers

Figure 28 - Installing Remote Receiver

Valve

White Wire From Receiver

Red Wire From Receiver

Figure 29 - Connecting Wires

Bac

Remote Receiver

Back

Page 16

INSTALLATION

Installing Wireless Remote Control Accessory

OPERATING FIREPLACE

For Your Safety Read Before Lighting

INSTALLATION

Continued

INSTALLING WIRELESS REMOTE CONTROL ACCESSORY

Two 9-volt alkaline batteries (not included) are required to operate this heater with the wireless hand held remote control set. One battery must be installed in the receiver and one in the hand-held

Note:

remote control unit.

Installing 9-Volt Battery in Receiver

1. Locate back of receiver under front burner of heater.

2. Locate the battery clip mounted on the back of the receiver.

3. Slide a 9-volt battery through the clip.

4. Attach the terminal wires to the battery.

Only use alkaline batteries.

9-Volt Battery

Battery Cover

Figure 32 - Installing Battery in Hand-Held Remote Control Unit (CGHRCTA Series)

Terminal Wires

Remote Control Unit

OPERATING FIREPLACE

Receiver

Terminal

9-Volt Battery

Figure 30 - Installing Receiver on the Back of the Base

Battery Clip

Wires

Installing 9-Volt Battery (Not Included) in HandHeld Remote Control Unit

1. Remove battery cover on back of remote control unit.

2. Attach terminal wires to the battery. Place battery into the battery housing.

3. Replace battery cover onto remote control unit.

Battery

Terminal Wires

9-Volt Battery

Figure 31 - Installing Battery in Hand-Held Remote Control Unit (CGHRC Series)

Cover

Remote Control Unit

Battery Housing

FOR YOUR SAFETY READ

BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance ar ea

for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

For more information, visit www.desatech.com

105442-01E

Page 17

OPERATING FIREPLACE

Continued

OPERATING FIREPLACE

Lighting Instructions

To Turn Off Gas To Appliance

Manual Lighting Procedure

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Open a window to vent smell. This will only last a few hours.

1. STOP! Read the safety information on page 16, column 2.

2. Make sure equipment shutoff valve is fully open.

3. Set switch in OFF position.

WARNING: Burner will come on automatically within one minute when the selector switch is in the ON position after the pilot is lit.

4. Press in and turn control knob clockwise to the OFF position.

5. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information on page 16, column 2. If you don’t smell gas, go to the next step.

6. Press in and turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 33).

Note:

You may be running this heater for the first time

after hooking up to gas supply . If so, the contr ol knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

7. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner . If needed, keep pr essing ignitor button until pilot lights.

Note:

If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs ar e made, light pilot with match. T o light pilot with matc h, see Manual Lighting Procedure.

8. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

• If control knob does not pop out when released, contact

a qualified service person or gas supplier for repairs.

Note:

If pilot goes out, repeat steps 4 through 8.

Selector Switch

AUTO

OFF

Ignitor Button

Figure 33 - Control Knob and Ignitor Button Location (Shown as Supplied, No Control Options)

Flame Adjustment Knob

Control Knob

9. Slightly push in and turn control knob counterclockwise to the ON position.

10. W ait one minute and switch selector switch to the ON posi-

tion to light burner.

11. Set flame adjustment knob to any level between HI and LO.

CAUTION: Do not try to adjust heating levels by

using the equipment shutoff valve.

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position.

Pilot Burner

Figure 34 - Pilot

Ignitor Electrode

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise to the OFF position. 2a. Set selector switch in the OFF position 2b. If Using Optional Hand-Held Remote: Set selector switch

in the OFF position to keep from draining battery.

Shutting Off Burner Only (pilot stays lit)

You may shut off the burner and keep the pilot lit by doing one of the following:

1. T urn control knob clockwise to the PILOT position.

2. Use remote control manual OFF button.

3. Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 6 under Lighting Instructions.

2. Depress control knob and light pilot with match.

3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11 under Lighting Instructions.

105442-01E

For more information, visit www.desatech.com

Page 18

OPERATING FIREPLACE

Optional Remote Operation

OPERATING FIREPLACE

Continued

OPTIONAL REMOTE

OPERATION

Note:

All remote control accessories must be purchased separately (see Accessories, page 31). Follow instructions included with the remote control.

Thermostat Control Operation

(Optional CGHRCTA Series Only) The thermostat control setting on the remote control unit can be set to any comfort level between HI and LO. The burner will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

NOTICE: You must light the pilot before using the hand-held remote control unit. See

tions

on page 17.

1. After lighting, let pilot flame burn for about one minute.

Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position. may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote contr ol unit.

IMPORTANT:

Do not leave the selector switch in the REMOTE position when the pilot is not lit. This will drain the battery.

IMPORTANT:

Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation.

Flame Adjustment Knob

ON OFF REMOTE

Selector Switch in Remote Position (Optional Remote Control)

Figure 35 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

Lighting Instruc-

NOTE:

The burner

Control Knob in On Position

CGHRC Series Operation:

2a. Press the ON/OFF button to turn the burner on and off.

When turning burner off, the pilot will remain lit.

CGHRCTA Series Operation

2b. Press the A UT O/ON/OFF b utton on the hand-held r emote

control (see Figure 36). The lights to the left of the button will show AUTO, ON, or OFF.

• In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit.

• In the AUTO mode, the thermostat in the hand-held remote unit controls the room temperature. T o incr ease the room temperature, press the top arro w of the TEMP button. To lower the room temperature, press the bottom arrow of the TEMP b utton. At higher settings the heater will run longer.

IMPORTANT:

gineered to take an air temperature sample every 5.5 minutes in the auto mode. It will not respond immediately to the temperature setting being turned up or down.

IMPORTANT:

be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

3. To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit.

IMPORTANT:

trol knob on the heater to the OFF position.

Shows Temperature Setting

The Log Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected

Figure 36 - Thermostat Hand-Held Remote Control Unit Selections (CGHRCTA Series only)

This remote contr ol has been specially en-

The hand-held remote control unit must

T o tur n the pilot off, manually turn the con-

Increases Room Temperature in AUTO Mode

Decreases Room Temperature in AUTO Mode

Turns Burners On or Off and Allows You to Choose the Auto Setting

For more information, visit www.desatech.com

105442-01E

Page 19

INSPECTING BURNERS

Pilot Flame Pattern

Burner Flame Pattern

Burner Primary Air Holes

Main Burner

CLEANING AND MAINTENANCE

Cleaning Burner Injector Holder And Pilot Air Inlet Hole

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 37 shows a correct pilot flame pattern. Figure 38 shows an incorrect pilot flame pattern. The incorrect pilot flame is not properly heating the thermocouple. When the thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 38

• turn heater off (see To Turn Off Gas to Appliance, page 17)

•

see Troubleshooting, pages 21 through 23

Pilot Burner

Figure 37 - Correct Pilot Flame Pattern

Pilot Burner

Figure 38 - Incorrect Pilot Flame Pattern

Thermocouple

BURNER FLAME PATTERN

Figure 39 shows a correct burner flame pattern. Figure 40 shows an incorrect burner flame pattern. If burner flame pattern is incorrect,

• turn heater off (see To Turn Off Gas to Appliance, page 17)

• see Troubleshooting, pages

Approx. 3-6" Above Top of Logs

Figure 39 - Correct Flame Pattern with Control Knob Set to High Flame

More Than 8" Above Top of Logs

21 through 23

BURNER PRIMARY AIR HOLES

Air is drawn into the burner through the holes in the fitting at the burner entrance. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean if needed. Blocked air holes will create soot.

MAIN BURNER

Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off heater and let cool. Remove blockage. Blocked burner flame holes will create soot.

CLEANING AND MAINTENANCE

WARNING: Turn off heater and let cool before

cleaning.

CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

Figure 40 - Incorrect Flame Pattern with Control Knob Set to High Flame

For more information, visit www.desatech.com

105442-01E

Page 20

CLEANING AND MAINTENANCE

Cleaning Burner Injector Holder And Pilot Air Inlet Hole (Cont.) Cabinet

SPECIFICATIONS WIRING DIAGRAM

CLEANING AND MAINTENANCE

Continued

2. Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 41).

3. Blow air through the ports/slots and holes in the burner.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the injector holder.

6. In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 42). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Injector Holder (May Be Brass or Aluminum Depending on Model)

Burner Tube

Primary Air Inlet Holes (Shape of Holes May Vary by Model)

Figure 41 - Injector Holder On Outlet Burner Tube

Ports/Slots

Burner Tube

Pilot Assembly

Pilot Air Inlet Hole

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air to clean.

Exterior

• Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.

SPECIFICATIONS

Btu (Variable) 19,000/26,000 Type Gas Propane/LP Only Ignition Piezo Manifold Pressure 8" W.C. Inlet Gas Pressure (in. of water) *

Maximum 14" Minimum 11"

Dimensions, Inches (H x W x D)

Fireplace 25 7/8 x 27 x 13 3/4 Carton 28 x 26 13/16 x 16 1/2

Weight, pounds

Fireplace 44 1/2 lbs. Shipping 55 lbs.

* For purposes of input adjustment

WIRING DIAGRAM

Auto

Off On

Thermopile

Switch

Black

Red

White

TPTH TH

Gas Control

TPTH

Figure 42 - Pilot Inlet Air Hole

For more information, visit www.desatech.com

105442-01E

Page 21

TROUBLESHOOTING

Note:

For additional help, visit DESA

International’s technical service web site at www.desatech.com.

Note:

All troubleshooting items are listed in

order of operation.

OBSERVED PROBLEM

When ignitor button is pressed, there is no spark at ODS/pilot

When ignitor button is pressed, there is spark at ODS/pilot but no ignition

WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.

POSSIBLE CAUSE

1. Ignitor electrode not connected to ignitor cable

2. Ignitor cable pinched or wet

3. Piezo ignitor nut is loose

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned wrong

1. Gas supply turned off or equipment shutoff valve closed

2. Control knob not in PILOT position

3. Control knob not pressed in while in PILOT position

4. Air in gas lines when installed

5. Depleted gas supply

6. ODS/pilot is clogged

7. Gas regulator setting is not correct

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry

3. Tighten nut holding piezo ignitor to base panel of log set. Nut is located behind base panel

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace pilot assembly

7. Replace pilot assembly

1. Turn on gas supply or open equipment shutoff valve

2. Turn control knob to PILOT position

3. Press in control knob while in PILOT position

4. Continue holding down control knob. Repeat igniting operation until air is removed

5. Contact local propane/LP gas company

6. Clean ODS/pilot (see Cleaning and Maintenance, pages 19 and 20) or replace ODS/pilot assembly

7. Replace gas control

ODS/pilot lights but flame goes out when control knob is released

For more information, visit www.desatech.com

105442-01E

1. Control knob not fully pressed in

2. Control knob not pressed in long enough

3. Equipment shutoff valve not fully open

4. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This problem could be caused by one or both of the following: A) Low gas pressure B) Dirty or partially clogged ODS/pilot

5. Thermocouple connection loose at control valve

6. Thermocouple damaged

7. Control valve damaged

1. Press in control knob fully

2. After ODS/pilot lights, keep control knob pressed in 30 seconds

3. Fully open equipment shutoff valve

4. A) Contact local propane/LP gas company

B) Clean ODS/pilot (see Cleaning and Maintenance, pages 19 and 20) or replace ODS/pilot assembly

5. Hand tighten until snug, then tighten 1/4 turn more

6. Replace pilot assembly

7. Replace control valve

Page 22

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

Burner does not light after ODS/pilot is lit

Delayed ignition burner

Burner backfiring during combustion

Slight smoke or odor during initial operation

POSSIBLE CAUSE

1. Burner orifice clogged

2. Inlet gas pressure is too low

3. Thermopile leads disconnected or improperly connected

4. Burners will not come on in remote position

1. Manifold pressure is too low

2. Burner orifice clogged

1. Burner orifice is clogged or damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

3. Residues from manufacturing processes and logs curing

REMEDY

1. Clean burner (see Cleaning and Maintenance, pages 19 and 20) or replace

burner orifice

2. Contact local propane/LP gas company

3. Reconnect leads (see Wiring Diagram, page 20)

4. Replace battery in transmitter and receiver

1. Contact local propane/LP gas company

2. Clean burner (see Cleaning and Main- tenance, pages 19 and 20) or replace burner orifice

1. Clean burner (see Cleaning and Main- tenance, pages 19 and 20) or replace burner orifice

2. Replace damaged burner

3. Replace gas control

1. Check burner for dirt and debris. If found, clean burner (see Cleaning and Maintenance, pages 19 and 20)

2. Replace gas control

3. Problem will stop after a few hours of operation

Moisture/condensation noticed on windows

Heater produces a whistling noise when burner is lit

White powder residue forming within burner box or on adjacent walls or furniture

Remote does not function

For more information, visit www.desatech.com

1. Not enough combustion/ventilation air

1. Turning control knob to HI position when burner is cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orifice

1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. may turn into white powder residue

1. Battery is not installed. Battery power is low

1. Refer to Air for Combustion and Venti- lation requirements (page 4)

1. Turn control knob to LO position and let warm up for a minute

2. Operate burner until air is removed from line. Have gas line checked by local propane/LP gas company

3. Observe minimum installation clearances (see pages 7 through 9)

4. Clean burner (see Cleaning and Mainte- nance, pages 19 and 20) or replace burner orifice

1. Turn heater off when using furniture polish, wax, carpet cleaners, or similar products

1. Replace 9-volt batteries in receiver and remote control

105442-01E

Page 23

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

TROUBLESHOOTING

IMPORTANT:

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.

Operating heater where impurities in air exist may create odors. Cleaning

OBSERVED PROBLEM

Heater produces a clicking/ticking noise just after burner is lit or shut off

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF position

POSSIBLE CAUSE

1. Metal expanding while heating or contracting while cooling

1. Heater burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (See ment above)

2. Gas leak. See Warning statement at

top of page

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak. See Warning statement at

top of page

2. Control valve defective

IMPORTANT

state-

REMEDY

1. This is common with most heaters. If noise is excessive, contact qualified service person

1. Open window and ventilate room. Stop using odor causing products while heater is running

2. Locate and correct all leaks (see Check- ing Gas Connections, page 14)

1. Open window and/or door for ventilation

2. Contact local propane/LP gas company

3. Clean ODS/pilot (see Cleaning and Maintenance, pages 19 and 20)

1. Locate and correct all leaks (see Check- ing Gas Connections, page 14)

2. Replace control valve

Gas odor during combustion

For more information, visit www.desatech.com

105442-01E

1. Foreign matter between control valve and burner

2. Gas leak. See Warning statement at

top of page

1. Take apart gas tubing and remove foreign matter

2. Locate and correct all leaks (see Check- ing Gas Connections, page 14)

Page 24

ILLUSTRATED PARTS BREAKDOWN

CF26PR

ILLUSTRATED PARTS BREAKDOWN

CF26PR

For more information, visit www.desatech.com

105442-01E

Page 25

PARTS LIST

CF26PR

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 28 of this manual.

KEY PART NO. NUMBER DESCRIPTION QTY.

1 106039-01 Log Set 1 2 103778-01 ODS Pilot (LP) 1 3 098249-01 ODS Nut 2 4 104422-04 Burner Outlet Tube 1 5 098264-02 Male Connector 1 6 111124-01 Burner Retainer Spring 1 7 099056-21 Burner Orifice Injector 1 8 099998-01 Switch 1 9 102980-01 Burner 1 10 099387-13 Pilot Tube 1 11 103781-02 Gas Control Valve 1 12 103345-02 Lower Bracket 1 13 M11084-38 Screw, #8 x .38 7 14 104384-04 Base Assy 1 15 098271-10 Ignitor Cable 1 16 102445-01 Piezo Ignitor 1 17 103587-02 Plate, Switch 1 18 104099-01 Heat Shield 1 19 098304-01 Screw 2 20 103784-02 Flame Adjustment Knob 1 21 103784-01 Off-Pilot-On Knob 1 22 M12461-26 Screw, Hex Slt Wsr 10-32 x .38 4 23 103284-02 Wiring Harness

PARTS AVAILABLE — NOT SHOWN

PARTS LIST

CF26PR

105442-01E

100563-01 Warning Plate 1 103877-01 Lighting Instructions Plate 1

For more information, visit www.desatech.com

Page 26

ILLUSTRATED PARTS BREAKDOWN

CF26PR

ILLUSTRATED PARTS BREAKDOWN

CF26PR

20-1

11-2

11-1

20-2

20-3

For more information, visit www.desatech.com

105442-01E

Page 27

PARTS LIST

CF26PR

This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under Replacement Parts on page 28 of this manual.

KEY CF26PR NO. PART NO. DESCRIPTION QTY.

1 102633-02 Outer Casing Top 1 2 102624-02 Outer Casing 1 3 099230-02 Shoulder Screw 12 4 105631-01CK Assy. Hood Weldment 1 5 105258-01CK Vertical Front, Left and Right Sides 2 6 105259-01 Firebox Top 1 7 ** Firebox Wrapper 1 8 105255-01 Bayfront Base 1 9 105421-01 Heat Deflector 1 10 105409-01 Fan Control Shield 1 11-1 105401-01 Screen Rod 1 11-2 105440-01 Screen Assembly 1 12 101386-02 Hinge 2 13 099194-11 Rivets 8 14 105262-01CK Louvered Door 1 15 ** Firebox Floor 1 16 098304-01 Screw, #10 x 3/8" 21 17 105256-01CK Bayfront Bottom Panel 1 18 M11084-26 Hex Head Screws #10 x .38 26 19 105513-01CJ Cover, Screen Rod 1 20-1 105525-01 Fiber Brick, Left 1 20-2 105524-01 Fiber Brick, Rear 1 20-3 105526-01 Fiber Brick, Right 1 21 105987-01 Brick Liner Retainer 2

PARTS LIST

CF26PR

105442-01E

PARTS AVAILABLE — NOT SHOWN

103877-01 Lighting Instructions Plate 1 100563-01 Warning Plate 1 103470-01 Hardware Package 1

**Not a field replacement part.

For more information, visit www.desatech.com

Page 28

REPLACEMENT PARTS PARTS CENTRALS TECHNICAL SERVICE SERVICE HINTS

REPLACEMENT PARTS

Note:

Use only original replacement parts. This will protect your

warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA International’s Technical Service Department at 1-866-672-6040. When calling DESA International, have ready

• your name and address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date Usually, we will ask you to return the part to the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA International at 1-866-672-6040 for referral information. When calling DESA International, have ready

• model number of your heater

• the replacement part number

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact DESA International’s Technical Service Department at 1-866-672-6040. When calling please have your model and serial numbers of your heater ready.

You can also visit DESA International’s technical services web site at www.desatech.com.

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• heater will not produce specified heat

• propane/LP gas supply may be low You may feel your gas pressure is low. If so, contact your local

natural or propane/LP gas supplier.

PARTS CENTRALS

These Parts Centrals are privately owned businesses. They have agreed to support our customer’s needs by providing original replacement parts and accessories.

Baltimore Electric

1348 Dixwell Avenue Hamden, CT 06514-0322 1-800-397-7553 203-248-7553 Parts Department

Portable Heater Parts

342 N. County Rd. 400 East Valparaiso, IN 46383-9704 All States 219-462-7441 1-888-619-7060 sales@portableheaterparts.com techservice@portableheaterparts.com

FBD

1349 Adams Street Bowling Green, KY 42103-3414 270-846-1199 1-800-654-8534 Fax: 1-800-846-0090 franktalk@aol.com

Master Parts Dist.

1251 Mound Ave NW Grand Rapids, MI 49504-2672 616-791-0505 1-800-446-1446 Fax: 616-791-8270 www.nbmc.com

Washer Equipment Co.

1715 Main Street Kansas City, MO 64108-2195 KS, MO, AR 816-842-3911 www.washerparts.com

East Coast Energy Products

707 Broadway W. Long Branch, NJ 07764-1542 732-870-8809 1-800-755-8809 www.njplaza.com/ecep

Halco Enterprises

208 Carter Drive, Unit 21 West Chester, PA 19382-4500 610-430-7717 1-800-368-0803 www.halcoenterprises.com

Laporte’s Parts & Service

2444 N. 5th Street Hartsville, SC 29550-7704 843-332-0191 Parts Department

Cans Unlimited, Inc.

P.O. Box 645 Taylor, SC 29687-0013 All States 803-879-3009 1-800-845-5301 cuisales@aol.com

For more information, visit www.desatech.com

105442-01E

Page 29

OWNER'S REGISTRATION FORM

In order to provide better customer service for this and future purchases, we recommend that you register your product with us. You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owner’s Registration Form and mail to the address on the back of this owner’s manual. Please provide the following product information:

Brand: Model: Date Purchased: Serial Number: First Name: Last Name: Address: City: State: Zip: Country: Home Phone: ( ) - E-Mail:

Please answer the following questions to register your product with DESA International:

1. Where will the product be used? ❍ Living/Family Room ❍ Office/Warehouse ❍ Utility Shed/Outbuilding ❍ Garage ❍ Bedroom ❍ Bathroom ❍ Other

2. If you bought this product yourself, did you plan to purchase this type of product before going into the store? ❍ Yes ❍ No

3. Who selected the product? ❍ Male ❍ Female ❍ Both

4. What is the population of your area? ❍ Under 10,000 ❍ 10,000 to 25,000 ❍ 25,000 to 50,000 ❍ 50,000 to 100,000 ❍ 100,000 to 250,000 ❍ Over 250,000

5. What is your primary source of heat? ❍ Propane (LP Gas) ❍ Fuel Oil ❍ Wood ❍ Natural Gas ❍ Electric ❍ Other

6. How was the product installed? ❍ Professional Installer ❍ Self ❍ Other

7. Cost of product excluding sales tax? $___________________

8. Cost to install product? $____________________

9. Type of store where product was purchased? ❍ Hardware ❍ Propane Dealer ❍ Natural Gas/Utility Co. ❍ Home Center/Builder’s Suppl ❍ Fireplace or Hearth Shop ❍ Farm Store ❍ Other

10. What motivated you to buy this product? ❍ Sudden Cold Weather ❍ Replace Older Model ❍ D.I.Y. Home Project ❍ Emergency Back-Up Heat ❍ Heater was on Sale ❍ Energy Savings/High Efficiency ❍ Construction Project ❍ Other

11. How did you learn about this product brand? ❍ Advertising ❍ Relative or Friend ❍ Store Display ❍ Other ________________________

12. Level of Education of Purchaser: ❍ Some High School ❍ Completed High School ❍ Completed College ❍ Completed Graduate School

13. Age of Purchaser: ❍ Under 20 ❍ 20 - 29 ❍ 30 - 39 ❍ 40 - 49 ❍ 50 - 59 ❍ 60 or Over

14. Buyer’s total annual household income: ❍ Under $15,000 ❍ $15,000 to $19,999 ❍ $20,000 to $34,999 ❍ $35,000 to $49,999 ❍ $50,000 to $74,999 ❍ $75,000 to $99,999 ❍ $100,000 and Over

15. Store where product was purchased: Name: ______________________________________ City: _______________________ State: __________

16. In choosing this product, how important were the following:

Availability Price Brand Name Overall Quality Heat Output Made in USA Warranty Local Service Value for Price Prior Brand Experience Controls Location Thermostat, Remote, or Manual Operation Ease of Operation Special Features Salesperson’s Recommendation Friend/Relative’s Recommendation

For more information, visit www.desatech.com

Portability Quiet Operation

105442-01E

Not Important Somewhat Important Very Important

(Comfort Glow, Vanguard, etc.) (EFP33PR, VTGH33NR, etc.)

Note:

Keep receipt for warranty verification.

7 or 9 digit number located on product or identification tag.

❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍

Page 30

TAPE

2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004

Postage

Required

For more information, visit www.desatech.com

TAPE

105442-01E

Page 31

ACCESSORIES

Purchase these fireplace accessories from your local dealer or Parts Central (see page 28). If they cannot supply these accessories call DESA International’s Sales Department at 1-866-672-6040 for referral information. You can also write to the address listed on the back page of this manual.

EQUIPMENT SHUTOFF VALVE - GA5010

Equipment shutoff valve with 1/8" NPT tap.

THERMOSTATICALLY CONTROLLED BLOWER KIT - GA3450T

Provides better heat distribution. Blower turns off and on automatically, as needed. Complete installation and operating instructions included.

R A

N O

BRASS ACCENT TRIM - GA7092 (Not Shown)

Optional two piece brass trim kit for the Bayfront Fireplace. Easily screws to fireplace front. Provides an upscale appearance.

BRASS ACCENT TRIM - GA6095

Opti on al four-sided bra ss trim kit for built-in installations. Provides a finished appearance covering rough edges of wall opening.

A U T O

O F F

O N

RECEIVER AND HAND-HELD THERMOSTAT REMOTE CONTROL KIT - CGHRCT SERIES

Allows the gas log heater to be operated in a manually or thermostatically-controlled mode. You can turn the gas log heater on and off without ever leaving the comfort of your easy chair.

RECEIVER AND HAND-HELD REMOTE CONTROL KIT - CGHRC SERIES

Allows the gas log heater to be turned on and off by using a hand-held remote control.

For more information, visit www.desatech.com

105442-01E

CABINET MANTEL WITH BUILT-IN HEARTH BASE Unfinished Hardwood Veneer - GMC46U White Lacquer Finish - GMC47W Medium Stained Oak Veneer - GMC45F

For use with fireplace. A hardwood mantel and hearth base offers compact styling and completes the fireplace look. Available in a white lacquer finish, medium stained oak, or an unfinished hardwood, ready to stain or paint. Complete assembly instructions included. Three-sided brass trim kit included.

CLEANING KIT - CCK (Not Shown)

Your vent-free gas appliance requires regular cleaning and maintenance to prevent performance problems. This kit gives you the tools and instructions to make it easy to clean all critical areas of your appliance.

INFORMATION VIDEO - 108917-01

A care and maintenance video is available by calling 1-866-672-6040.

Page 32

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model Serial No. Date Purchased

Always specify model and serial numbers when communicating with the factory. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We

make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE PROPANE/LP GAS HEARTH

DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this fireplace to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The fireplace MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective fireplace will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

‚

FIREPLACE

For information about this warranty write:

For more information, visit www.desatech.com

2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004

www.desatech.com

105442 01

NOT A UPC

105442-01 Rev. E 02/03

105442-01E

Desa Tech CF26PR, NMCF26PT Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual