Desa Tech CF26NRA, CF26PRA Owner's Manual

Download

Page 1

UNVENTED (VENT-FREE) BAY FRONT GAS LOG FIREPLACE

A U T O

O F F

O N

OWNER’S OPERATION AND INSTALLATION MANUAL

Patent Pending

Fireplace Shown With

Optional Mantel

MODELS CF26PRA AND CF26NRA

19,000 TO 26,000 BTU/HR REMOTE CONTROL READY

WARNING: If the information in this manual is not fol-

lowed exactly, a re or explosion may result causing property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.

For more information, visit www.desatech.com

Page 2

TABLE OF CONTENTS

Safety Information ............................................... 2

Local Codes......................................................... 4

Unpacking............................................................ 4

Product Identication ........................................... 5

Product Features ................................................. 5

Remote Control Accessories ............................... 5

Air For Combustion and Ventilation ..................... 5

Installation ........................................................... 8

Operating Fireplace ........................................... 20

Inspecting Burners ............................................ 23

Cleaning and Maintenance ................................ 23

SAFETY INFORMATION

Troubleshooting ................................................. 25

Specications .................................................... 29

Wiring Diagram .................................................. 29

Replacement Parts ............................................ 29

Service Hints ..................................................... 29

Technical Service............................................... 29

Illustrated Parts Breakdown and Parts List........ 30

Parts Central...................................................... 34

Accessories ....................................................... 34

Warranty Information ...........................Back Cover

WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause in-

jury or property damage.

Refer to this manual for correct installation and

operational procedures.

For assistance or additional information con-

sult a qualied installer, service agency or the gas supplier.

WARNING: This is an

unvented gas-red heater. It uses air (oxygen)

from the room in which

it is installed. Provisions for adequate combustion

and ventilation air must

be provided. Refer to Air for Combustion and Ventilation section on page 5

of this manual.

This appliance may be in-

stalled in an aftermarket,*

per man ent ly loc ate d, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

State of Massachusetts: The installation must be made by a licensed plumber or gas tter in the Commonwealth of Massachusetts.

Sel lers of unvented propane or natural gas-red supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

www.desatech.com

113897-01E2

Page 3

SAFETY INFORMATION

Continued

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects or other reproductive harm.

WARNING: Do not allow fans

to blow directly into the replace. Avoid any drafts that alter burner ame patterns. Ceiling fans can create drafts that alter burner ame patterns. Altered burner patterns can cause sooting.

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate or service this replace. Improper use of this replace can cause serious injury or death from burns, re, explosion, electrical shock and carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the u, with headaches, dizziness or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the inuence of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent

is added to the gas. The odor helps you detect a gas

leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

Due to high temperatures, the appliance should be located out of trafc and away from furniture and draperies.

Do not place clothing or other ammable material on or near the appliance. Never place any objects in the replace or on logs.

Fireplace front and screen become very hot when running replace. Keep children and adults

away from hot surfaces to avoid

burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with replace. When using the

hand-held remote accessory,

keep selector switch in the OFF position to prevent children from turning on burners with remote.

You must operate this replace with a replace screen in place. Make sure replace screen is closed before running heater.

WARNING: Do not use a

blower insert, heat exchanger insert or other accessory not approved for use with this heater.

113897-01E 3

www.desatech.com

Keep the appliance area clear and free from combustible materials, gasoline and other ammable vapors and liquids.

Page 4

SAFETY INFORMATION

Continued

1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply

tank(s) outdoors (propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• if you cannot reach your gas supplier, call

the re department

4. This replace shall not be installed in a bed-

room or bathroom.

5. Do not use this replace as a wood-burning replace. Use only the logs provided with the replace.

6. Do not add extra logs or ornaments such as pine cones, vermiculite or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of replace.

7. This replace is designed to be smokeless. If logs ever appear to smoke, turn off replace and call a qualied service person. Note: During initial operation, slight smoking could occur due to log curing and replace burning manufacturing residues.

8. To prevent the creation of soot, follow the instructions in Cleaning and Maintenance, page 23.

9. Before using furniture polish, wax, carpet cleaner or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

10. This replace needs fresh air ventilation to run properly. This replace has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the replace if not enough fresh air is available. See Air for Combustion and Ventilation, page 5. If replace keeps shutting off, see Troubleshooting, page 25.

11. Do not run replace

• where ammable liquids or vapors are used

or stored.

• under dusty conditions.

12. Do not use this replace to cook food or to burn paper or other solid fuels.

13. Do not use replace if any part has been under water. Immediately call a qualied service technician to inspect the room replace and to replace any part of the control system and any gas control which has been under water.

14. Turn off and unplug replace and let cool before servicing. Only a qualied service person should service and repair replace.

15. Operating replace above elevations of 4,500 feet could cause pilot outage.

16. Do not operate replace if any log is broken. Do not operate replace if a log is chipped (dime-sized or larger).

17. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity (propane/LP units only).

18. Prov ide adeq ua te clearan ce s around air

openings.

LOCAL CODES

Install and use replace with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park Quincy, MA 02269

UNPACkING

1. Remove replace from carton.

2. Remove all protective packaging applied to replace for shipment.

3. Make sure your replace includes one hardware packet.

4. Check replace for any shipping damage. If replace is damaged, promptly inform dealer where you bought replace.

www.desatech.com

113897-01E4

Page 5

PRODUCT

IDENTIFICATION

Fireplace Cabinet

Brick Liner

Logs

Heater Controls

Hand-held Remote Control (Optional)

Figure 1 - Vent-Free Propane/LP Gas

(Inside Door)

Compact Fireplace

Screen

PRODUCT FEATURES

SAFETY PILOT

This replace has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room replaces. The ODS/pilot shuts off the replace if there is not enough fresh air.

PIEzO IGNITION SYSTEM

This replace has a piezo ignitor. This system requires no matches, batteries or other sources to light replace.

REMOTE CONTROL

ACCESSORIES

There are two optional remote controls that can be purchased separately for this log heater:

• hand-held ON/OFF remote

• hand-held thermostat remote

See Accessories, page 34.

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a conned space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.

Today’s homes are built more energy efcient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efcient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, replaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for

these appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54 Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will help you classify your space and provide adequate ventilation.

113897-01E 5

www.desatech.com

Page 6

AIR FOR COMBUSTION

AND VENTILATION

Continued

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10 less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window and door frames, between sole plates and oors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical and gas lines and at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three

criteria above, proceed to Determining Fresh-Air Flow For Fireplace Location.

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1 denes a conned space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconning space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconned space.

* Adjoining rooms are communicating only if

there are doorless

-11

kg per pa-sec-m2) or

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Conned or Unconned Space

Use this work sheet to determine if you have a conned or unconned space.

Space: Includes the room in which you will install

heater plus any adjoining rooms with doorless passageways or ventilation grills between the

rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free replace ___________ Btu/Hr

Gas water heater* ___________ Btu/Hr

Gas furnace ___________ Btu/Hr

Vented gas heater ___________ Btu/Hr

Gas replace logs ___________ Btu/Hr

Other gas appliances* + ___________ Btu/Hr

Total = ___________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

Gas water heater __________ Btu/Hr

Vent-free replace + ________ Btu/Hr

Total = ________ Btu/Hr

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________

_________ Example: 51,200 Btu/Hr (maximum the space

56,000 Btu/Hr (actual amount of

Btu/Hr (maximum the space can support)

Btu/Hr (actual amount of Btu/Hr used)

can support)

Btu/Hr used)

30,000

26,000

56,000

www.desatech.com

113897-01E6

Page 7

AIR FOR COMBUSTION

Remove Door into Adjoining

Room, Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Into Adjoining

Room,

Option 1

12"

Outlet Air

Ventilated Attic

Outlet A

Inlet Air

Ventilated

Crawl Space

To Attic

Crawl

Space

AND VENTILATION

Continued

The space in the above example is a conned space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconned space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors.

C. Install a lower Btu/Hr replace, if lower Btu/Hr

size makes room unconned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an un-

conned space. You will need no additional fresh

air ventilation.

WARNING: If the area in

which the heater may be operated is smaller than that dened as an unconned space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described

in the National Fuel Gas Code, ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

Figure 2 - Ventilation Air from Inside

Building Shown with Optional Mantel

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the oor. Connect these items directly to the

outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts. IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostatcontrolled power vent. Heated air entering the attic will activate the power vent.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conned space. When ventilating to an adjoining

unconned space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the oor on the wall connecting

the two spaces (see options 1 and 2, Figure 2). You

can also remove door into adjoining room (see

option 3, Figure 2). Follow the National Fuel Gas

Code ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

113897-01E 7

www.desatech.com

Figure 3 - Ventilation Air from Outdoors

Shown with Optional Mantel

Page 8

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualied service person must install replace. Follow all local codes.

Note: Your replace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface of your replace, except where standoff spacers are integrally attached. If standoff spacers are attached to your replace, these spacers can be placed directly against wall or framing materials.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fire- place Installation, page 9).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your unit. If your gas supply is not correct, do not install replace. Call dealer where you bought replace for proper type replace.

WARNING: This appliance is equipped for natural or propane/LP gas. Field conversion is not permitted.

LOCATING FIREPLACE

WARNING: Maintain the minimum clearances shown

in Figure 4, page 9. If you can, provide greater clearances from oor, ceiling and joining wall.

You can recess rebox into the wall. You can also position replace in the optional cabinet mantels. IMPORTANT: Only use optional cabinet mantels specied in this manual. Purchase the optional mantel from your dealer (see Accessories, page 34).

WARNING: Never install the

replace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, f urni ture,

clothing or other ammable objects are less than 42" from the front, top or sides of the replace

• as a replace insert

• in high trafc areas

• in windy or drafty areas

CAUTION: This replace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to replace. Installing replace next to vinyl or cloth wall coverings or operating replace where impurities (such as, but not limited to, tobacco

smoke, aromatic candles, clean-

ing uids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free replaces add moisture to the air. Although this is benecial, installing replace in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, page 5.

CAUTION: If you install the

replace in a home garage

• replace pilot and burner must be at least 18" above oor.

• locate replace where moving vehicle will not hit it.

For convenience and efciency, install replace

• where there is easy access for operation, inspection and service.

• in coldest part of room.

www.desatech.com

113897-01E8

Page 9

INSTALLATION

3/4" Off The Floo

Minimum

Continued

An optional blower kit is available from your dealer. See Accessories, page 34. If planning to use blower, locate replace near an electrical outlet.

Note: When installing replace directly on carpeting, tile or other combustible material, other than wood ooring, the replace shall be installed on a metal or wood panel extending the full width and depth of the replace.

Minimum Clearances For Side Combustible Material, Side Wall and Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall should follow diagram in Figure 4.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and protrudes 3 1/2" from the wall. This combustible material must be 4" from the side of the replace opening (see Figure 4).

B. Clearances from the top of the replace opening

to the ceiling should not be less than 42".

Example

1. Frame in rough opening. Use dimensions shown

in Figure 5 for the rough opening.

If installing in a corner, use dimensions shown

in Figure 6 for the rough opening. The height is 26 1/8" which is the same as the wall opening above.

2. An optional blower accessory is available (see

Accessories, page 34). There are two options for connecting blower to electrical source.

Option one: Have a licensed electrician install

a properly grounded, three-prong 120-volt electrical outlet at replace location. Locate outlet inside the framed enclosure. Blower power cord will plug into this outlet.

Option two: Have a licensed electrician con-

nect blower to electrical source at junction box inside replace.

If using option one, have electrical outlet in-

stalled at this time. If using option two, do not connect blower to electrical source at junction

box until step 6.

3. Install gas piping to replace location. This

installation includes an approved exible gas line (if allowed by local codes) after the equipment shutoff valve. The exible gas line must

be the last item installed on the gas piping.

4. Carefully set replace in front of rough opening

with back of replace inside wall opening.

5. Attach exible gas line to replace gas regula-

tor. See Connecting Fireplace to Gas Supply, page 16.

*Minimum 16" from Side Wall

Figure 4 - Minimum Clearance for

Combustible to Wall

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this replace involves installing replace into a framed-in enclosure. This makes the front of replace ush with wall. Follow the instructions below to install the replace in this manner. If installing a built-in mantel above the replace, you must follow the clearances shown in Figure 8, page 11.

Actual Framing Height 26" 26 7/8" Front Width 26 3/4" 26 7/8" Depth 9 1/2" 10 1/2"

113897-01E 9

www.desatech.com

Figure 5 - Rough Opening for Installing

in Wall

Figure 6 - Rough Opening for Installing

in Corner

Page 10

INSTALLATION

Continued

6. If the optional blower has been installed connect blower to electrical source.

Option one: Route blower electrical cord

through side or rear access door of replace.

Plug electrical cord into electrical outlet.

Option two: Have a licensed electrician con-

nect blower to electrical source at junction box inside replace.

7. Bend four nailing anges on outer casing with pliers (see Figure 7).

8. Attach fireplace to wall studs using nails or wood screws through holes in nailing ange.

9. Check all gas connections for leaks. See Checking Gas Connections, page 17.

IMPORTANT: When finishing your firebox, combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top of the rebox. Combustible materials should never overlap the rebox front facing. Firebox should not be placed on top of carpet or other kinds of brous material.

WARNING: Do not allow any

combustible materials to overlap the rebox front facing.

IMPORTANT: Noncombustible materials such as

brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.

WARNING: Do not allow non-

combustible materials to cover any necessary openings like louvered slots.

WARNING: Never modify or

cover the louvered slots on the

front of the rebox.

Nails or Wood Screws

Nailing Flanges

Figure 7 - Attaching Fireplace to Wall

Studs

Mantel Clearances for Built-In Installation

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all

minimum clearances shown in

this manual.

If placing mantel above built-in replace, you must meet minimum clearance between mantel shelf and top of replace opening.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one

of the following:

• raise the mantel to an acceptable height

• remove the mantel

WARNING: Use only non-

combustible mortar or adhesives when overlapping the front facing with noncombustible facing material.

www.desatech.com

113897-01E10

Page 11

13"

16"

19"

21"

2 1/2"

10"

Minimum NonCombustible Material

Note: All vertical measurements are from top

of replace

opening to bottom of mantel shelf.

REMOVING BRICK LINER

RETAINER

1. Using Phillips screw driver, remove 2 screws

2. Remove brick liner retainers and discard.

ASSEMBLING TRIM

(Trim shipped with mantel)

1. Rem ove packaging from three pieces of

2. Locate two adjusting plates with set screws

3. Align shim under adjusting plate as shown in

4. Slide one end of adjusting plate/shim in slot

5. Slide other end of adjusting plate/shim in slot

6. While rmly holding edges of trim together,

7. Repeat steps 1 through 6 for other corner.

8. Set trim assembly aside for later installation.

INSTALLATION

Continued

Mantel Shelf

Figure 8 - Minimum Mantel Clearances

for Built-In Installation

attaching brick liner retainers to vertical

sides.

Replace 2 screws into vertical sides.

trim.

and two shims in the hardware packet.

Figure 9.

on mitered edge of top trim (see Figure 9).

on mitered edge of side trim (see Figure 9).

tighten both set screws on the adjusting plate with slotted screwdriver.

Set Screws

Top Trim

Slot

Shim

Mitered Edge

Side

Adjusting

Trim

Plate

Slot

Figure 9 - Assembling Trim

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the man- tel for assembly instructions. Refer to instructions below for system installation. If using blower accessory (see Accessories, page 34), see installation instructions on pages 12 through 15.

1. Choose location for replace and install gas

supply line.

2. Remove screen from replace by removing screws in each end of screen rod (see Figure

10). Hold screen rod cover while removing ve hex head screws underneath hood (see Figure 11). Carefully lift and pull out hood (see Figure 12, page 12).

Figure 10 - Removing Screen

Hood

Screen Rod Cover

Screw

Figure 11 - Removing Hood Screws

113897-01E 11

www.desatech.com

Page 12

INSTALLATION

Continued

3. Assemble trim kit. See Assembling Trim,

page 11.

4. Place trim on the shoulder screws located on the side and top of the replace. Firmly snap the trim over the shoulder screws on replace (see Figure 13).

5. Place mantel base close to wall in desired replace location.

6. Install gas line. See Connecting To Gas Sup- ply, page 15

7. Carefully place replace on mantel base and center left to right. Check for gas leaks. See Checking Gas Connections, page 17.

8. Refer to instructions provided with the mantel for permanent attachment to wall.

9. Slide mantel around replace. Be careful not to damage wall or mantel.

10. Adjust assembly to remove any gaps. From back side of replace, attach two 2" wood screws through base mounting blocks attached to bottom sides of mantel into base (see instructions provided with mantel).

11. Attach remaining two 3" wood screws from hardware pack through openings inside of replace sides into the mantel. See Figure 12 for screw hole location.

Mantel Screw Location

Figure 12 - Removing Hood

Shoulder Screws

INSTALLING BLOWER ASSEMBLY

GA3450TA

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

CAUTION: Verify proper operation after servicing.

Note: If you are using a mantel with your heater, use the following instructions. If your heater is built-in, see For Built-In Installation on page 14.

1. Screen and hood should be removed from replace (see page 11). Remove log set and

set aside.

2. Install snap bushings found in hardware kit into both holes in rear of blower control shield (see Figure 14).

3. Make sure the wire harness is rmly connected to the terminals on the blower bracket

assembly.

4. Note the wire locations on back of AUTO/ OFF/ON switch. Carefully remove red wire from the AUTO terminal and blue wire from the ON terminal. Black wire can remain on the middle or OFF terminal (see Figure 15, page 13).

5. Carefully disconnect green and white wires from power cord harness at their insulated

connectors.

6. In top of the heater cabinet, locate the four

mounting holes on the outer casing. Align

these four holes with those on the blower bracket assembly. Attach blower bracket assembly to the outer casing with 4 - #10 screws provided (see Figure 15, page 13).

7. Route the wire harness through the hole to the left side of heat deector. Pull wire harness through lower opening to the left of the blower control shield. (see Figure 15, page 13).

Blower Control Shield

Snap Bushing

Assembled Trim

Figure 13 - Attaching Trim to Fireplace

www.desatech.com

Figure 14 - Installing Snap Bushings

113897-01E12

Page 13

INSTALLATION

Continued

8. Insert the 4 wire harness into one of the round holes in the rear of the blower control shield and through the rectangular hole in the front of shield (see Figure 15).

9. Reconnect red wire to the AUTO switch position. Reconnect blue wire to the ON switch position. Reconnect green and white wires to the power cord.

10. Install the switch plate on the blower control shield with 2 - #10 screws provided (see Fig-

Blower Bracket Assembly

Screw

Switch

Wire Harness Power

Cord

Red

Blue

Switch Plate

Blower Control Shield

Wire Harness

ure 16). Route power cord out of the cabinet

by inserting it through the bushing on the

outer casing (see Figure 15). Plug fan kit into 120-Volt grounded power supply and test operation. Note: When switch is in the AUTO position, the fan will start after the heater has run for a few moments. The fan will continue to run for several moments after the heater has been turned off. When switch is in the ON position, the fan will run until turned to OFF. Reinstall hood assembly and close lower louver door.

Wiring Routing Hole

Heat

Deector

Shield Cover

Figure 15 - Installing Blower Bracket Assembly

Blower Control Shield

Switch Plate

Screw

Figure 16 - Installing Switch Plate to Blower Control Shield

113897-01E 13

www.desatech.com

Page 14

INSTALLATION

Continued

For Built-In Installation

WARNING: A licensed elec-

trician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of heater.

WARNING: ELECTRICAL

GROUNDING INSTRUCTIONS

This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.

Blower Bracket Assembly

1. Install a snap bushing found in hardware kit into one of the holes found on rear of blower control shield. The other hole is for a strain relief clamp (not supplied) to secure incoming

electrical supply.

2. Follow steps 2 through 6 in Installing Blower Assembly, page 12. Also remove black wire

from middle/OFF switch terminal.

3. Remove black plastic strain relief and power cord from switch plate (see Figure 17). The power cord supplied will not be used in built-

in installations. Pop in the plastic snap bushing

found in hardware kit into the hole left by supply cord/strain relief.

4. A licensed electrician must follow the wiring diagram in Figure 18, page 15 to connect incoming electrical supply to fan kit wiring

harness.

5. Test to make sure the blower is working

properly.

6. Reinstall hood assembly (see page 12) and close lower louver door.

7. Place log set back into unit.

Screw

Switch

Switch Plate

Strain Relief

Blue

Blower Control Shield

Red

Clamp Connector (not included)

Figure 17 - Installing Blower Bracket Assembly

Wire Harness

Power Cord

Outlet Receptacle

Shield Cover

Wire Harness

www.desatech.com

113897-01E14

Page 15

Red

Fan Switch

(Auto/Off/On)

Blue

Thermostat

Switch

(N.O.)

Green

White

Green

White

110/115

V.A.C.

Blower

Motor

Black

Off

Auto

INSTALLATION

Continued

WARNING: Never attempt to service heater while it is plugged in, operating or hot. Burns and electrical shock could result. Only a qualied service person should service or repair heater.

If any of the original wire as supplied with the appliance must be replaced original replacements must be used. DESA part no. 104015-01 (105°C) for power cord and DESA part no. 103968-01 (200°C) for wire harness.

WARNING: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

120 Vac. 60 Hz. .30 Amps DESA Heating Products, Bowling Green, KY

Figure 18 - Wiring Diagram For Fan

Accessory Built-In Installation

CONNECTING TO GAS SUPPLY

101584-06

Installation Items Needed

Before installing replace, make sure you have the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• test gauge connection *

* A CSA design-certied equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certied equipment shutoff valve from your dealer. See Accessories, page 34.

For propane/LP units, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11" and 14" of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 19. Pointing the vent down protects it from freezing rain or sleet.

WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator.

CAUTION: Use only new,

black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use

WARNING: A qualied service person must connect heater to gas supply. Follow all local codes.

CAUTION: Never connect propane/LP replace directly to the propane/LP supply. This replace

pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur.

Propane/LP Supply Tank

External Regulator

requires an external regulator (not supplied). Install the external regulator between the replace and propane/LP supply.

WARNING: Never connect

natural gas replace to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

113897-01E 15

www.desatech.com

Figure 19 - External Regulator With Vent

Pointing Down

Vent Pointing Down

Page 16

INSTALLATION

A U T O

O F F

O N

Continued

Installation must include an equipment shutoff valve, union and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 20).

IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to

the appliance.

Check your building codes for any special requirements for locating equipment shutoff valve to replaces.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could result

in clogged heater valves.

WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

We recommend that you install a sediment trap in

supply line as shown in Figure 20. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

CSA Design-Certied

Equipment Shutoff Valve With 1/8" NPT Tap*

Gas Control

Approved Flexible Gas Hose

3" Minimum

Figure 20 - Gas Connection

* Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 34.

** Minimum inlet pressure for purpose of input

adjustment.

Propane/LP

From External Regulator (11" W.C.** to 14" W.C. Pressure) Natural From Gas Meter (5" W.C.** to 10.5" W.C. Pressure)

Cap Pipe Tee Nipple Joint

Sediment Trap

www.desatech.com

CONNECTING FIREPLACE TO GAS SUPPLY

Installation Items Needed

• Phillips screwdriver

• sealant (re sistant to propane/LP gas, not provided)

1. Route exible gas line (provided by installer)

from equipment shutoff valve into replace

through side or rear access holes in outer

casing (see Figure 21).

NOTICE: Most building codes do not permit concealed gas connections. A exible gas line is provided to allow accessibility from the replace (see Figure 22). The exible gas supply line connection to the equipment shutoff valve should be accessible.

2. Apply pipe joint sealant lightly to male threads

of gas connector attached to exible gas line (see Figure 22). Connect exible gas line to exible gas line attached to gas valve of replace (see Figure 22).

Outer Casing

Equipment Shutoff Valve

Figure 21 - Routing Flexible Gas Line

To Fireplace

Equipment Shutoff

Gas Connector

Valve

Flexible Gas Line from

To Gas Supply

Equipment Shutoff Valve Provided by Installer

Figure 22 - Attaching Flexible Gas Lines

Together

Gas Valve

Flexible Gas Line from Fireplace Gas Valve Provided with Fireplace

113897-01E16

Page 17

INSTALLATION

Continued

3. Check all gas connections for leaks. See

Checking Gas Connections.

4. Feed exible gas line into replace base area. Make sure the entire exible gas line is in replace mantel base area.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or ttings.

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and external to unit, for leaks after

installing or servicing. Correct all leaks at once.

WARNING: Never use an

open ame to check for a leak. Apply a noncorrosive leak detection uid to all joints. Bubbles forming show a leak. Correct all leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed between propane/LP supply and heater. See guidelines under Con- necting to Gas Supply, page 15.

4. Check all joints of gas supply piping system. Apply noncorrosive leak detection uid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

Reconnect heater and equipment shutoff valve to gas supply. Check reconnected ttings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 23).

2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas

or using compressed air.

3. Check all joints from gas meter to equipment shutoff valve for natural gas or propane/LP supply to equipment shutoff valve for propane/LP (see Figures 24 and 25). Apply noncorrosive leak detection uid to all joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Equipment Shutoff Valve

Figure 23 - Equipment Shutoff Valve

Equipment Shutoff Valve

Open

Closed

Propane/LP Supply Tank

PRESSURE TESTING GAS SUPPLY PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage

heater regulator.

2. Cap off open end of gas pipe where equipment shutoff valve was connected.

3. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas

or using compressed air.

113897-01E 17

www.desatech.com

Figure 24 - Checking Gas Joints Propane/LP

Gas (Shown with Optional Mantel)

Equipment Shutoff Valve

Gas Meter

Figure 25 - Checking Gas Joints Natural

Gas (Shown with Optional Mantel)

Page 18

INSTALLATION

A U T O

O F F

O N

Front

Back

Continued

PRESSURE TESTING HEATER GAS CONNECTIONS

1. Open equipment shutoff valve (see Figure 23, page 17).

2. Open main gas valve located on or near gas meter for natural gas or open propane/LP supply tank valve.

3. Make sure control knob of heater is in the OFF

position.

4. Check all joints from equipment shutoff valve to thermostat gas valve (see Figures 24 and 25, page

17). Apply noncorrosive leak detection uid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater, page 20). Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to Appli- ance, page 21).

8. Replace front panel.

INSTALLING LOGS

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this heater may result in property damage or personal injury.

CAUTION: After installa-

tion and periodically thereafter, check to ensure that no ame comes in contact with any log.

With the heater set to HI, check

to see if ames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

It is very important to install the logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

Place one-piece log set on grate to t as illustrated in Figure 26. Make sure back section of log set is seated into “U”-shaped cutout in center of chassis (see Figure 26). IMPORTANT: Make sure log does not cover any burner ports (see Figure 27).

www.desatech.com

One-Piece Log Set

Burner

“U”-shaped

Chassis

Cutout in Chassis

Figure 26 - Installing One-Piece Log Set

Burner

One-Piece Log Set

Ports

Figure 27 - Installing One-Piece Log set

(Top View)

OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES

(HRC101 and HRC201 Series)

Installing Receiver

1. Disconnect switch wires from the control valve.

2. Remove screws and nuts.

3. Remove switch plate (see Figure 28). Discard after removing.

Front

Screw

Back

Nut

Figure 28 - Switch Plate and Wiring

Harness (Switch Plate and Orientation

May Vary Depending On Model)

Wires

113897-01E18

Page 19

INSTALLATION

Front

Back

Continued

4. Install remote receiver unit onto gas log heater base using clips (2) and insulating washers provided.

5. Push clips rmly into place (see Figure 29).

6. Connect wires as shown in Figure 30.

Front

Mounting Clips

Back

Remote Receiver

Insulating Washers

Figure 29 - Installing Remote Receiver

Valve

White Wire From Receiver

Red Wire From Receiver

Figure 30 - Connecting Wires

Receiver

9-Volt Battery

Terminal Wires

Battery Clip

Figure 31 - Installing Receiver on the

Back of the Base

Installing 9-Volt Battery (Not Included) in

Hand-Held Remote Control Unit

1. Remove battery cover on back of remote

control unit.

2. Attach terminal wires to the battery. Place

battery into the battery housing.

3. Replace battery cover onto remote control

unit.

Battery Cover

Remote Control Unit

Terminal Wires

Battery Housing

9-Volt Battery

Figure 32 - Installing Battery in Hand-Held

Remote Control Unit

INSTALLING WIRELESS REMOTE CONTROL ACCESSORY

Two 9-volt alkaline batteries (not included) are required to operate this heater with the wireless hand held remote control set. One battery must be installed in the receiver and one in the hand-

held remote control unit. Note: Only use alkaline batteries.

Installing 9-Volt Battery in Receiver

1. Locate back of receiver under front burner of

heater.

2. Locate the battery clip mounted on the back of the receiver.

3. Slide a 9-volt battery through the clip.

4. Attach the terminal wires to the battery.

113897-01E 19

www.desatech.com

Page 20

OPERATING FIREPLACE

AUTO

OFF

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a re or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be

lighted by hand. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next

to the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neig h bor ’s phon e. Fo llo w the gas supplier’s instructions.

• If you cannot reach your gas supplier, call

the re department.

C. Use only your hand to push in or turn the

gas control knob. Never use tools. If the

knob will not push in or turn by hand, don’t try to repair it, call a qualied service technician or gas supplier. Force or attempted

repair may result in a re or explosion.

D. Do not use this appliance if any part has

been under water. Immediately call a

qualied service technician to inspect the

appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Open a window to vent smell. This will only last a few hours.

1. STOP! Read the safety information above.

2. Make sure equipment shutoff valve is fully

open.

3. Set switch in OFF position.

www.desatech.com

WARNING: Burner will come on automatically within one minute when the selector switch

is in the ON position after the pilot is lit.

4. Press in and turn control knob clockwise

5. Wait ve (5) minutes to clear out any gas.

6. Press in and turn control knob counter-

Note: You may be running this heater for

7. With control knob pressed in, press and

Note: If pilot does not stay lit, contact a

8. Keep control knob pressed in for 30 seconds

Note: If pilot goes out, repeat steps 4

9. Slightly push in and turn control knob coun-

Ignitor Button

Button Location (Shown as Supplied, No

to the OFF position.

Then smell for gas, including near the oor.

If you smell gas, STOP! Follow “B” in the safety information, column 1. If you don’t smell gas, go to the next step.

clockwise to the PILOT position.

Press in control knob for ve (5) seconds (see Figure 33).

the rst time after hooking up to gas sup-

ply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

qualied service person or gas supplier for

repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 21.

after lighting pilot. After 30 seconds, release control knob.

• If control knob does not pop out when

released, contact a qualied service person

or gas supplier for repairs.

through 8.

terclockwise to the ON position.

Selector Switch

Flame Adjustment Knob

Control Knob

Figure 33 - Control Knob and Ignitor

Control Options)

113897-01E20

Page 21

OPERATING FIREPLACE

ON OFF REMOTE

Continued

10. Wait one minute and switch selector switch to the ON position to light burner.

11. Set ame adjustment knob to any level

between HI and LO.

CAUTION: Do not try to ad-

just heating levels by using the equipment shutoff valve.

WARNING: Make sure the

selector switch is in the OFF

position when you are away from home for long periods of time.

Heater will come on automatically with selector switch in the

ON position.

Pilot Burner

Propane/LP

Shutting Off Heater

1. Turn control knob clockwise to the OFF position.

2a. Set selector switch in the OFF position 2b. If Using Optional Hand-Held Remote: Set

selector switch in the OFF position to keep from draining battery.

Shutting Off Burner Only (pilot stays lit)

You may shut off the burner and keep the pilot lit by doing one of the following:

1. Turn control knob clockwise to the PILOT position.

2. Use remote control manual OFF button.

3. Set selector switch in the OFF position.

Ignitor Electrode

Pilot Burner

Natural Gas

Figure 34 - Pilot

TO TURN OFF GAS

TO APPLIANCE

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 6 under Lighting Instructions, page 20.

2. Depress control knob and light pilot with match.

3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11 under Lighting Instructions, page 20.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be

purchased separately (see Accessories, page

34). Follow instructions included with the

remote control.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instructions on page 20.

After lighting, let pilot ame burn for about one minute. Turn control knob to ON position. Adjust ame adjustment knob anywhere between HI and

LO. Slide the selector switch to the REMOTE position (see Figure 35). Note: The burner may light if hand-held remote was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch

in the REMOTE or ON position when the pilot is not lit. This will drain the battery.

Selector Switch in Remote Position (Optional Remote Control)

Figure 35 - Setting the Selector Switch,

Control Knob and Flame Adjustment

Flame Adjustment Knob

Control Knob in On Position

Knob for Remote Operation

113897-01E 21

www.desatech.com

Page 22

OPERATING FIREPLACE

LOCK

MANU AUTO

ºC/ºF

TEMP

POWER

ROOM TEMP

SET TEMP

AUTO

Continued

ON/OFF SERIES (MODEL HRC101)

Hold the control button on the hand-held remote until burner turns on. Hold the control button

again until burner turns off (see Figure 36).

TO LOCK press both buttons on hand-held

remote control until light stops ashing. Handheld remote control is now locked. If the re is

on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed.

TO UNLOCK press both buttons together on hand-held remote control until the light

stops ashing. The hand-held remote is now

unlocked.

Indicator Light

Control Button Turns Burners On and Off

Figure 36 - On/Off Hand-Held Remote

Control Unit (HRC101)

THERMOSTAT SERIES (MODEL HRC201)

The hand-held remote can be operated using

either the manual mode (MANU) or thermostatic mode (AUTO) (see Figure 37). To select

Fahrenheit/Centigrade mode display, carefully

press the ˚C/˚F mode button with the end of a paper clip or similar blunt object.

Digital Display Shows Temperature and Settings

Locks System to Prevent Accidental Ignition

Turns Burners On or Off

Increases and Decreases Room Temperature in AUTO Mode

Figure 37 - Thermostat Hand-Held

Remote Control Unit (HRC201)

Turns Hand-Held Remote On or Off and Allows You to Choose the Manual Setting

Selects Auto Setting

Manual Mode

1. Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2. Press the MANU button to turn on the

replace.

3. Press the POWER and LOCK buttons

together to turn off the replace.

Auto (Thermostatic) Mode

1. Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2. Press AUTO button to select this mode.

3. Set the desired room temperature by pressing the TEMP + or - buttons.

4. Press the POWER and LOCK buttons

together to turn off the replace

Note: Do not leave the hand-held remote in the AUTO mode close to the replace. The radiant heat from the replace will turn off the replace.

Ideally, place the hand-held remote in the center

of the room facing towards the replace.

Note: Do not hold the hand-held remote for a long time. Body temperature will affect its operation in the AUTO mode.

Safety Features

When away from home for an extended period

of time or as a child safety feature to prevent accidental ignition of the replace, the receiver

ON/OFF/REMOTE switch should be in the OFF position.

Auto Shutoff Feature

1. If the average room temperature exceeds 82 degrees Fahrenheit (28 degrees Centigrade), the hand-held remote control will perform a safety override and shut the replace off. This feature is not available

in the MANU mode.

2. The receiver continuously receives signals

from the hand-held remote to control the room temperature. If the hand-held remote is misplaced, obstructed or for any reason

cannot transmit to the receiver, the receiver will shut off the replace after 8 minutes.

Key Pad Lock Feature

This feature allows the user to lock/unlock the keypad on the hand-held remote in the

MANU or AUTO mode to prevent inadvertent operation (i.e. children operating the hand-held remote control, etc.). The keypad is locked in

either on or off. Press the POWER and LOCK buttons together to turn the unit on or off.

www.desatech.com

113897-01E22

Page 23

INSPECTING BURNERS

Check pilot ame pattern and burner ame patterns often.

PILOT FLAME PATTERN

Figure 38 shows a correct pilot ame pattern. Figure 39 shows an incorrect pilot ame pattern. The incorrect pilot ame is not properly heating the thermocouple. When the thermocouple cools, the heater will shut down.

If pilot ame pattern is incorrect, as shown in Figure 39

• turn heater off (see To Turn Off Gas to Appli- ance, page 21)

•

see Troubleshooting, page 25

Note: The correct pilot ame on natural gas units will have a slight curve, but ame should be blue and have no yellow or orange color.

Pilot Burner

Figure 38 - Correct Pilot Flame Pattern

(propane/LP ignitor shown)

Pilot Burner

Thermocouple

Approx. 3-6" Above Top of Logs

Figure 40 - Correct Flame Pattern with

Control Knob Set to High Flame

More Than 8" Above Top of Logs

Figure 41 - Incorrect Flame Pattern with

Control Knob Set to High Flame

BURNER PRIMARY AIR HOLES

Air is drawn into the burner through the holes in the tting at the burner entrance. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean if needed. Blocked air holes will create soot.

MAIN BURNER

Periodically inspect all burner ame holes with the heater running. All slotted burner ame holes should be open with yellow ame present. All round burner ame holes should be open with a small blue ame present. Some burner ame holes may become blocked by debris or rust, with no ame present. If so, turn off heater and let cool. Remove blockage. Blocked burner ame holes will create soot.

CLEANING AND

MAINTENANCE

WARNING: Turn off heater

Figure 39 - Incorrect Pilot Flame Pattern

(propane/LP ignitor shown)

BURNER FLAME PATTERN

Figure 40 shows a correct burner ame pattern. Figure 41 shows an incorrect burner ame pattern. If burner ame pattern is incorrect,

• turn heater off (see To Turn Off Gas to Appli- ance, page 21)

• see Troubleshooting, page

113897-01E 23

www.desatech.com

and let cool before cleaning.

CAUTION: You must keep control areas, burner and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualied service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

Page 24

CLEANING AND

MAINTENANCE

Continued

Injector Holder (May Be Brass or Aluminum Depending on Model)

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

BURNER INjECTOR HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning ame. Keep these holes clear of dust, dirt, lint and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualied service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can,

you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2. Inspect burner, pilot and primary air inlet holes on injector holder for dust and dirt (see Figure 42).

3. Blow air through the ports/slots and holes in

the burner.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint or pet hair with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the

injector holder.

6. In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot ame indicates dust and dirt in the pilot as-

sembly. There is a small pilot air inlet hole about

2" from where the pilot ame comes out of the pilot assembly (see Figure 43). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Burner Tube

Primary Air Inlet Holes (Shape of Holes May Vary by Model)

Figure 42 - Injector Holder On Outlet

Burner Tube

Ports/Slots

Burner Tube

Pilot Assembly

Pilot Air Inlet Hole

Figure 43 - Pilot Inlet Air Hole

CABINET

Air Passageways

Use a vacuum cleaner o r pressurized air to

clean.

Exterior

Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.

www.desatech.com

113897-01E24

Page 25

TROUBLESHOOTING

WARNING: Turn off heater and let cool before servicing. Only a

qualied service person should service and repair heater.

CAUTION: Never use a wire, needle or similar object to clean

ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM

When ignitor button is pressed, there is no spark at ODS/pilot

When ignitor button is pressed, there is spark at ODS/pilot but

no ignition

POSSIBLE CAUSE

1. Ignit or ele ct rode not con -

nected to ignitor cable

2. Ignitor cable pinched or wet

3. Piezo ignitor nut is loose

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode positioned wrong

7. Ignitor electrode broken

1. Gas supply turned off or equipment shutoff valve closed

2. Control knob not in PILOT

position

3. Control knob not pressed in while in PILOT position

4. Air in gas li nes whe n in-

stalled

5. Depleted gas supply (propane/ LP only)

6. ODS/pilot is clogged

7. Gas regulator setting is not

correct

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched

by any metal or tubing. Keep ignitor cable dry

3. Tighten nut holding piezo ignitor to base panel of log set. Nut is

located behind base panel

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace pilot assembly

7. Replace pilot assembly

1. Turn on gas supply or open

equipment shutoff valve

2. Turn control knob to PILOT

position

3. Press in control knob while in PILOT position

4. Continue holding down control knob. Repeat igniting operation until air is removed

5. Contact local propane/LP gas

company

6. Clean ODS/pilot (see Cleaning and Maintenance, page

23) or replace ODS/pilot assembly

7. Replace gas control

113897-01E 25

www.desatech.com

Page 26

OBSERVED PROBLEM

ODS /pilot ligh ts but fl ame goes out when control knob is

released

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

Control knob not fully pressed in

2. Control knob not pressed in

long enough

3. Equipment shutoff valve not fully open

4. Pilot ame not touching thermocouple, which allows thermoc ouple to cool, causing pilot flame to go out. This

problem could be caused by

one or both of the following:

A) Low gas pressure B) Dirty or partially clogged

ODS/pilot

5. The rmoco upl e conne ction loose at control valve

6. Thermocouple damaged

7. Control valve damaged

REMEDY

1. Press in control knob fully

After ODS/pilot lights, keep control knob pressed in 30 seconds

3. Fully open equipment shutoff valve

4. A) Contact local natural or

propane/LP gas company

B) Cle a n OD S/pi l ot (see

Cleaning and Maintenance, page 23) or replace ODS/pilot

assembly

5. Hand tighten until snug, then

tighten 1/4 turn more

6. Replace pilot assembly

7. Replace control valve

Burner does not light after ODS/pilot is lit

Delayed ignition of burner

Burner backring during com-

bustion

Slight smoke or odor during

initial operation

1. Inlet gas pressure is too low

2. Burner orice(s) clogged

3. Thermopile leads disconnected

or improperly connected

4. Burners will not come on in

remote position

1. Manifold pressure is too low

2. Burner orice(s) clogged

1. Burner orice is clogged or

damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

3. Residues from manufacturing

processes and logs curing

1. Contact local natural or propane/LP gas company

2. Clean burner(s) (see Cleaning and Maintenance, page 23) or

replace burner orice

3. Reconnect leads (see Wiring Diagram, page 29)

4. Replace battery in transmitter and receiver

1. Contact local natural or pro-

pane/LP gas company

2. Clean burner(s) (see Cleaning and Maintenance, page 23) or

replace burner orice

1. Clean burner (see Cleaning and Maintenance, page 23) or replace burner orice

2. Replace damaged burner

3. Replace gas control

1. Check burner for dirt and debris. If found, clean burner (see Cleaning and Mainte- nance, page 23)

2. Replace gas control

3. Problem will stop after a few hours of operation

www.desatech.com

113897-01E26

Page 27

OBSERVED PROBLEM

Moisture/condensation noticed on windows

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

1. Not enough combustion/ven-

tilation air

REMEDY

1. Refer to Air for Combustion and Ventilation requirements

(page 5)

Heater produces a whistling noise when burners are lit

White powder residue forming within burner box or on adjacent walls or furniture

Remote does not function

Heater produces a clicking/ticking noise just after burners are lit or shut off

1. Turning control knob to HI position when burners are cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or par tiall y clog ge d burner orice(s)

1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. may turn into white powder residue

1. Battery is not installed. Bat-

tery power is low

1. Metal expanding while heating or contracting while cooling

1. Turn control knob to LO position and let warm up for a minute

2. Operate burners until air is removed from line. Have gas line checked by local natural

or propane/LP gas company

3. Observe minimum installation clearances (see page 9)

4. Clean burners (see Cleaning and Maintenance, page 23) or replace burner orice

1. Turn heater off when using furniture polish, wax, carpet

cleaners or similar products

1. Replace 9-volt batteries in receiver and hand held-remote

control

Thi s is normal with most heaters. If noise is excessive, co nta ct qu ali fie d ser vic e

person

113897-01E 27

www.desatech.com

Page 28

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.

OBSERVED PROBLEM

Heat er pr odu ce s u nwant ed

odors

POSSIBLE CAUSE

1. Heater burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (See IMPORTANT state- ment above)

2. Low fuel supply (propane/LP only)

3. Gas le ak. Se e War n i ng

statement at top of page

REMEDY

1. Op en window to ven ti late

room. Stop using odor caus-

ing products while heater is

running

2. Contact local propane/LP gas supplier to rell supply tank (propane/LP only)

3. Locate and correct all leaks (see Checking Gas Connec- tions, page 17)

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF position

Gas odor during combustion

1. Not enough fresh air is avail-

able

2. Low line pressure

3. O D S/ p il ot i s p a rt ia ll y

clogged

1. Gas le ak. Se e War n i ng statement at top of page

2. Control valve defective

1. Foreign matter between control valve and burner

2. Gas le ak. Se e War n i ng

statement at top of page

www.desatech.com

1. Open window and/or door for ventilation

2. Contact local natural or pro-

pane/LP gas company

3. Clean ODS/pilot (see Cleaning and Maintenance, page 23)

1. Locate and correct all leaks (see Checking Gas Connec- tions, page 17)

2. Replace control valve

1. Take apart gas tubing and remove foreign matter

2. Locate and correct all leaks (see Checking Gas Connec- tions, page 17)

113897-01E28

Page 29

SPECIFICATIONS

Switch

Black

Auto

Off On

Red

White

Thermopile

Gas Control

TPTH TH

TPTH

CF26NRA

• Rating: 19,000/26,000 Btu/hr

• Gas Type: Natural

• Ignition: Piezo

• Manifold Pressure: 3.5" w.c.

• Inlet Gas Pressure (in. of water)*: Maximum - 10.5", Minimum - 5.5"

• Firebox Dimensions (HxWxD): 25 7/8" x 27" x 13 3/4"

CF26PRA

• Rating: 19,000/26,000 Btu/hr

• Gas Type: Propane/LP

• Ignition: Piezo

• Manifold Pressure: 8" w.c.

• Inlet Gas Pressure (in. of water)*: Maximum - 14", Minimum - 11"

• Firebox Dimensions (HxWxD): 25 7/8" x 27" x 13 3/4"

* For purposes of input adjustment

WIRING DIAGRAM

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA Heating Products’ Technical Service Department at 1-866-672-6040.

When calling DESA Heating Products, have

ready

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date

Usually, we will ask you to return the part to the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA Heating Products at 1-866-672-6040 for referral information.

When calling DESA Heating Products, have

ready

• model number of your heater

• the replacement part number

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• heater will not produce specied heat

• for propane/LP units, propane/LP gas supply may be low

You may feel your gas pressure is too low. If so, con-

tact your local propane/LP or natural gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, operation or troubleshooting. If so, contact DESA Heating Products’ Technical Service Department at 1-866-672-6040. When calling please have your model and serial numbers of your heater ready.

You can also visit DESA Heating Products’ techni-

113897-01E 29

www.desatech.com

cal services web site at www.desatech.com.

Page 30

ILLUSTRATED PARTS BREAkDOWN

MODELS CF26PRA AND CF26NRA

www.desatech.com

113897-01E30

Page 31

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions

PARTS LIST

listed under Replacement Parts on page 29 of this manual.

KEY NO. PART NO. DESCRIPTION QTY.

1 113342-01 Log Set • • 1 2 103778-01 ODS Pilot • 1

103779-01 ODS Pilot • 1 3 098249-01 ODS Nut • • 2 4 104422-05 Burner Outlet Tube • 1

111331-10 Burner Outlet Tube • 1 5 098264-02 Male Connector • • 1 6 111124-01 Burner Retainer Spring • • 1 7 099056-21 Burner Orice Injector • 1

099056-27 Burner Orice Injector • 1 8 099998-01 Switch • • 1 9 102980-01 Burner • • 1 10 099387-13 Pilot Tube • 1

099387-15 Pilot Tube • 1 11 103781-02 Gas Control Valve • 1

103781-01 Gas Control Valve • 1 12 103345-02 Lower Bracket • • 1 13 M11084-38 Screw, #8 x 0.38" • • 7 14 104384-04 Base Assembly • • 1 15 098271-10 Ignitor Cable • • 1 16 102445-01 Piezo Ignitor • • 1 17 103587-02 Plate, Switch • • 1 18 104099-01 Heat Shield • • 1 19 098304-01 Screw • • 2 20 103784-02 Flame Adjustment Knob • • 1 21 103784-01 Off-Pilot-On Knob • • 1 22 M12461-26 Screw, Hex Slt Wsr 10-32 x 0.38" • • 4 23 103284-02 Wiring Harness • • 1 24 099918-02 Pilot Regulator • 1 25 100609-01 Pilot Tube

PARTS AVAILABLE — NOT SHOWN

100563-01 Warning Plate • • 1

103877-01 Lighting Instructions Plate

CF26PRA

CF26NRA

•

• • 1

113897-01E 31

www.desatech.com

Page 32

ILLUSTRATED PARTS BREAkDOWN

11-2

11-1

20-2

20-3

20-1

MODELS CF26PRA AND CF26NRA

www.desatech.com

113897-01E32

Page 33

PARTS LIST

MODELS CF26PRA AND CF26NRA

This list contains replaceable parts used in your replace. When ordering parts, follow the instructions listed under Replacement Parts on page 29 of this manual.

KEY NO. PART NO. DESCRIPTION QTY.

1 102633-02 Outer Casing Top 1 2 102624-02 Outer Casing 1 3 099230-02 Shoulder Screw 12 4 105631-01CK Assy. Hood Weldment 1 5 105258-01CK Vertical Front, Left and Right Sides 2 6 ** Firebox Top 1 7 ** Firebox Wrapper 1 8 ** Bayfront Base 1 9 105421-01 Heat Deector 1 10 105409-01 Fan Control Shield 1 11-1 105401-01 Screen Rod 1 11-2 105440-01 Screen Assembly 1 12 101386-02 Hinge 2 13 ** Rivets 8 14 105262-01CK Louvered Door 1 15 ** Firebox Floor 1 16 098304-01 Screw, #10 x 3/8" 21 17 105256-01CK Bayfront Bottom Panel 1 18 M11084-26 Hex Head Screws #10 x .38 26 19 105513-01CK Cover, Screen Rod 1 20-1 105525-01 Fiber Brick, Left 1 20-2 105524-01 Fiber Brick, Rear 1 20-3 105526-01 Fiber Brick, Right 1 21 105987-01 Brick Liner Retainer 2

PARTS AVAILABLE — NOT SHOWN

103877-01 Lighting Instructions Plate 1 100563-01 Warning Plate 1 103470-01 Hardware Package 1

**Not a eld replacement part.

113897-01E 33

www.desatech.com

Page 34

PARTS CENTRAL

These Parts Centrals are privately owned businesses. They have agreed to support our customer’s needs by providing original replacement parts and accessories.

Tools & Equipment Co.

5 Manila Ave Hamden, CT 06514-0322 1-800-397-7553 or 203-248-7553

Portable Heater Parts

342 N. County Rd. 400 East Valparaiso, IN 46383-9704 219-462-7441 or 1-888-619-7060 www.portableheaterparts.com

sales@portableheaterparts.com

techservice@portableheaterparts.com

FBD

1349 Adams Street Bowling Green, KY 42103-3414 270-846-1199 1-800-654-8534 Fax: 1-800-846-0090 franktalk@aol.com

Master Parts Dist.

1251 Mound Ave. NW Grand Rapids, MI 49504-2672 616-791-0505 or 1-800-446-1446 www.nbmc.com

Washer Equipment Co.

1715 Main Street Kansas City, MO 64108-2195 KS, MO, AR 816-842-3911 www.washerparts.com

East Coast Energy

10 East Route 36 W. Long Branch, NJ 07764 732-870-8809 or 1-800-755-8809 www.njplaza.com/ecep

21st Century

2950 Fretz Valley Road Perkasie, PA 18944-4034 215-795-0400 or 1-800-325-4828

Laporte’s Parts & Service

2444 N. 5th Street Hartsville, SC 29550-7704 843-332-0191 Parts Department

Cans Unlimited

P.O. Box 645 Taylor, SC 29687-0013 803-879-3009 or 1-800-845-5301

cuisales@aol.com

ACCESSORIES

Purchase these heater accessories from your local dealer or Parts Central (see column 1). If they can not supply these accessories, call DESA Heating Products at 1-866-672-6040 for referral information. You can also write to the address listed on the back page of this manual.

EQUIPMENT SHUTOFF VALVE

GA5010

For all models. Equipment shutoff valve with 1/8" NPT tap. Fits 1/2" NPT pipe.

THERMOSTATICALLY CONTROLLED

BLOWER KIT - GA3450TA

Provides better heat distribution. Blower turns off and on automatically, as needed. Complete instal-

lation and operating instructions included.

RECEIVER AND HAND-HELD THERMOSTAT REMOTE CONTROL

KIT - HRC201

For all Remote-Ready Models. Allows the gas

log heater to be operated in a manually or ther-

mostatically controlled mode. You can turn the gas log heater on and off without ever leaving the comfort of your easy chair. A wall-mount docking

station is included.

RECEIVER AND HAND-HELD

REMOTE CONTROL KIT - HRC101

For all Remote-Ready Models. Allows the gas log heater to be turned on and off by using a hand-held remote control. A wall-mount docking

station is included.

www.desatech.com

113897-01E34

Page 35

ACCESSORIES

Continued

BRASS ACCENT TRIM - GA7092 (Not Shown)

Optional two piece trim kit for the Bayfront Fireplace. Easily screws to replace front. Provides an

upscale appearance.

BRASS ACCENT TRIM - GA6095

Optional four-sided trim kit for built-in installations. Provides a nished appearance covering rough edges of wall opening.

CORNER MANTEL WITH FULL HEARTH BASE (Not Shown)

GMC83F - Oak Finished, Georgian Design CS26CP - Black/Red Oak, Cottage Design GMC63UD - Unnished, Traditional Design CMA208FB - Light Oak Finished,

Traditional Design

For all models. Space-saving mantel and hearth base corner design features clean, classic lines. Available in a stained oak, 2-tone nish or an unfinished hardwood, ready to stain or paint. Complete assembly instructions included. Threesided perimeter trim kit included.

CABINET MANTEL AND FULL HEARTH BASE (Not Shown)

GMC61UD - Unnished, Traditional Design GMC80FA - Light Oak Finished, Georgian

Design

CMA205UA - Unnished, Traditional Design CMA204FA - Light Oak Fininshed,

Traditional Design

CMA210W - White, Traditional Design WS26CP - Black/Red Oak, Cottage Design WD26CPA - White, Cottage Design WS26DS - Red Oak, Keystone Design WD26GOSA - Dark Oak, Mission Design

For all models. Mantel features clean, classic lines. Available in a stained oak, 2-tone nish, painted white or an unnished hardwood, ready to stain or paint. Complete assembly instructions included. Three-sided perimeter trim kit

included.

CLEANING KIT - GCK

(Not Shown)

For all models. Your vent-free gas appliance requires regular cleaning and maintenance to prevent performance problems. This kit gives you the tools and instructions to make it easy to clean all critical areas of your appliance.

INFORMATION VIDEO - 108917-01

For all models. A care and maintenance video is available by calling 1-866-672-6040. You may also

email your request to

productsupport@desaint.com.

113897-01E 35

www.desatech.com

Page 36

WARRANTY INFORMATION

113897 01

kEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE GAS BAY FRONT FIREPLACE

DESA Heating Products warrants this product to be free from defects in materials and components for four (4) years from the date of rst purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check

must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating condition and an allowance for labor when provided by a DESA Heating Products Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA Heating Products who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualied installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO FOUR (4) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA HEATING PRODUCTS’ LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA HEATING PRODUCTS SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on

damages may not apply to you.

This warranty gives you specic legal rights, and you may also have other rights that vary from state to state. For information about this warranty write:

2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 www.desatech.com

NOT A UPC

113897-01 Rev. E 05/06

Desa Tech CF26NRA, CF26PRA Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

SAFETY INFORMATION

LOCAL CODES

UNPACkING

PRODUCT FEATURES

INSTALLATION

OPERATING FIREPLACE

INSPECTING BURNERS

TROUBLESHOOTING

SPECIFICATIONS

WIRING DIAGRAM

REPLACEMENT PARTS

SERVICE HINTS

TECHNICAL SERVICE

ILLUSTRATED PARTS BREAkDOWN

PARTS CENTRAL

ACCESSORIES

WARRANTY INFORMATION