Desa VVTR18, VVTR24 User Manual

®

NATURAL GAS LOG

VENTED DECORATIVE APPLIANCES

OWNER’S OPERATION AND INSTALLATION MANUAL

Models VVTR18

TESTED AND

LISTED BY

Std RADCO Listing No. 1292

CAMBRIDGE SPLIT LOG SETS

and VVTR24

RGA 2-72

APPROVED

FOR USE WITH

VTLCR18 AND VTLCR24

WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury, or
loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any
other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use
any phone in your building.

• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call
the fire department.

— Installation and service must be performed by

a qualified installer, service agency, or the
gas supplier.

WARNING: Improper installa­tion, adjustment, alteration, ser­vice, or maintenance can cause
injury or property damage. Re­fer to this manual for correct
installation and operational
procedures. For assistance or
additional information consult
a qualified installer, service
agency, or the gas supplier.

WARNING: This appliance is
for installation only in a solid­fuel burning masonry or UL127
factory-built fireplace, con­structed of noncombustible
material, and connected to a
working flue. (See page 7 for
minimum flue opening.)

WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which
it is installed. Provisions for adequate combustion and ventilation air must be
provided. Refer to

Air for Combustion and Ventilation

section on page 4 of this manual.

This appliance may be installed in an aftermarket* manufactured (mobile) home,
where not prohibited by state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

®

VENTED NATURAL GAS LOGS

SAFETY
INFORMATION

WARNINGS

WARNING ICON G 001

WARNING: Keep flue open

when operating unit.

IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, oper­ate, or service this log set. Im­proper use of this log set can cause
serious injury or death from burns,
fire, explosion, electrical shock,
and carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the
flu, with headaches, dizziness, or nausea. If
you have these signs, the log set may not be
working properly. Get fresh air at once!
Have log set serviced. Some people are
more affected by carbon monoxide than
others. These include pregnant women,
people with heart or lung disease or anemia,
those under the influence of alcohol, and
those at high altitudes.

Natural Gas: Natural gas is odorless. An

odor-making agent is added to the gas. The
odor helps you detect a gas leak. However,
the odor added to the gas can fade. Gas may
be present even though no odor exists.

Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this log set.

WARNING: Any change to this
log set or its controls can be
dangerous.

1. This appliance, as supplied, is only for
use with the type of gas indicated on
the rating plate. This appliance is con­vertible for use with propane/LP , using
the GA9003 or GA9103 pilot kit.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier

from a neighbor’s phone. Follow the
gas supplier’s instructions

• if you cannot reach your gas supplier ,

call the fire department

3. Never install the log set

• in a recreational vehicle

• where curtains, furniture, clothing, or

other flammable objects are less than
42 inches from the front, top, or sides
of the log set

• in high traffic areas

• in windy or drafty areas

4. Before installing in a solid fuel burn­ing fireplace, the chimney flue and fire­box must be cleaned of soot, creosote,
ashes, and loose paint by a qualified
chimney cleaner. Creosote will ignite
if highly heated. Inspect chimney flue
for damage.

5. You must operate this log set with a fire­place screen in place. Make sure fireplace
screen is closed before running log set.

6. This log set is designed to be smoke­less. If logs ever appear to smoke, turn
off appliance and call a qualified ser­vice person.
eration, slight smoking could occur due
to log curing and the burning of manu­facturing residues. Y ou may wish to add
more ventilation by opening a window .

7. To reduce the creation of soot, follow
the instructions in Cleaning and Main-
tenance, page 17.

8. Do not allow fans to blow directly into
the fireplace. Avoid any drafts that al­ter burner flame patterns. Ceiling fans
can create drafts that alter burner flame
patterns. Altered burner patterns can
increase sooting.

Note:

During initial op-

9. Do not use a blower insert, heat ex­changer insert or other accessory not
approved for use with this log set.

10. This log set needs fresh, outside air ven­tilation to run properly. See Air for
Combustion and Ventilation, pages 4
through 6.

11. Do not run log set

• where flammable liquids or vapors

are used or stored

• under dusty conditions

12. Do not burn solid fuel in the fireplace
after installing the log set. Do not use
this log set to cook food or burn paper
or other objects.

13. Log set becomes very hot when in use.
Keep children and adults away from hot
surface to avoid burns or clothing igni­tion. Log set will remain hot for a time
after shutdown. Allow surface to cool
before touching.

14. Carefully supervise young children
when they are in the room with log set.

15. Do not use appliance if any part has been
exposed to or under water. Immediately
call a qualified service technician to in­spect the room appliance and to replace
any part of the control system (if using
GA9003 or GA9103) and any gas con­trol which has been under water.

16. To help prevent breakage, new logs
must be broken-in (see Curing logs
page 13).

17. Turn log set off and let cool before ser­vicing, installing, or repairing. Only a
qualified service person should install,
service, or repair log set.

2

901847

OWNER’S MANUAL

PRODUCT
IDENTIFICATION

Rear Burner

Grate

Burner
Pan

Front
Burner

Figure 1 - Product Identification

Serial Number ________________________________________

LOCAL CODES

Install and use log set with care. Follow all
local codes. In the absence of local codes, use
the latest edition of The National Fuel Gas
Code ANS Z223.1, also known as NFPA 54*.

*Available from:
American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

CAUTION: Do not remove the
metal data plates from the burner
pan. The d ata plates contain im­portant product information.

1. Remove logs, hearth kit, pan materi­als, and hardware from carton.

2. Remove all protective packaging ap­plied to logs and base for shipment.

3. Check all items for any shipping dam­age. If damaged, promptly inform
dealer where you bought the product.

Valve
Cover

OPTIONAL
PRODUCT
FEATURES

ON/OFF SAFETY VALVE/
PILOT KIT AND PROPANE/LP
CONVERSION

An optional valve/safety pilot kit with a
piezo ignitor is available for this appliance.
This system requires no matches, batteries,
or other sources to light. You must use this
optional system for LP conversion. See Ac-
cessories, page 17.

REMOTE CONTROL READY
(MILLIVOLT) SAFETY VALVE/
PILOT KIT

An optional millivolt valve/safety pilot kit
with a piezo ignitor is available for this
appliance. This system requires no matches,
batteries, or other sources to light. This
system may be connected to a wall switch or
hand-held wireless remote control. See Ac-
cessories, page 17.

REMOTE CONTROL
ACCESSORIES

There is an optional hand-held ON/OFF
remote control that can be purchased sepa­rately for this log set. You must use the
millivolt valve/safety pilot kit to use remote
accessories with this appliance. See Acces-
sories, page 17.

LOG SETS

Model VTLCR18 log set is for use with
Model VVTR18 burner set. Model
VTLCR24 log set is for use with Model
VVTR24 burner set. Use these log sets only
with their corresponding burners.

901847

3

®

VENTED NATURAL GAS LOGS

AIR FOR
COMBUSTION AND
VENTILATION

WARNING: This appliance
shall not be installed in a con­fined space or unusually tight
construction unless provisions
are provided for adequate com­bustion and ventilation air. Read
the following instructions to in­sure proper fresh air for this and
other fuel-burning appliances in
your home.

Today’s homes are built more energy effi­cient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home owners
weather strip and caulk around windows and
doors to keep the cold air out and the warm air
in. During heating months, home owners
want their homes as airtight as possible.

While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper com­bustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide ad­equate fresh air for these appliances. This
will insure proper venting of vented fuel­burning appliances.

PROVIDING ADEQUATE
VENTILATION

The following are excerpts from National
Fuel Gas Code, NFPA 54/ANS Z223.1, Sec­tion 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three
following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space
The information on pages 4 through 6 will

help you classify your space and provide
adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and win­dows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.

Unusually tight construction is de­fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con­tinuous water vapor retarder with
a rating of one perm (6x10
per pa-sec-m2) or less with open­ings gasketed or sealed

b. weather stripping has been

added on openable windows and
doors

c. caulking or sealants are applied

to areas such as joints around
window and door frames, be­tween sole plates and floors, be­tween wall-ceiling joints, be­tween wall panels, at penetra­tions for plumbing, electrical, and
gas lines, and at other openings.

If your home meets all of the three
criteria above, you must provide ad­ditional fresh air. See

From Outdoors

If your home does not meet all of the
three criteria above, proceed to

and

Ventilation Air

, page 6.

termining Fresh-Air Flow For Log Set
Location

, page 5.

and

-11

kg

De-

Confined and Unconfined Space

The National Fuel Gas Code, ANS Z223.1
defines a confined space as a space whose
volume is less than 50 cubic feet per 1,000
Btu per hour (4.8 m3 per kw) of the aggre­gate input rating of all appliances installed
in that space and an unconfined space as a
space whose volume is not less than 50
cubic feet per 1,000 Btu per hour (4.8 m3 per
kw) of the aggregate input rating of all
appliances installed in that space. Rooms
communicating directly with the space in
which the appliances are installed*, through
openings not furnished with doors, are con­sidered a part of the unconfined space.

This log set shall not be installed in a con­fined space or unusually tight construction
unless provisions are provided for adequate
combustion and ventilation air.

* Adjoining rooms are communicating only
if there are doorless passageways or ventila­tion grills between them.

4

901847

OWNER’S MANUAL

AIR FOR
COMBUSTION AND
VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR APPLIANCE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install appliance plus any adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height).
Length x Width x Height = _________________cu. ft. (volume of space)

Example:

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_____________ (volume of space) ÷ 50 cu. ft. = (maximum Btu/Hr the space can support)

Example:

3. Add the Btu/Hr of all fuel burning appliances in the space.
Gas fireplace logs _____________ Btu/Hr

Gas water heater* _____________ Btu/Hr
Gas furnace _____________ Btu/Hr
Vented gas heater _____________ Btu/Hr
Vent-free heater _____________ Btu/Hr
Other gas appliances* + _____________ Btu/Hr
Total = _____________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_____________ Btu/Hr (maximum the space can support)
_____________ Btu/Hr (actual amount of Btu/Hr used)

Example:

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air Fr om Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

Example:

Gas water heater 40,000 Btu/Hr
Gas fireplace logs + 55,000 Btu/Hr
Total = 95,000 Btu/Hr

51,200 Btu/Hr (maximum the space can support)
95,000 Btu/Hr (actual amount of Btu/Hr used)

WARNING: If the area in which the appliance may be operated is smaller than that defined as an unconfined
space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one
of the methods described in the

901847

National Fuel Gas Code, ANS Z223.1, Section 5.3

5

or applicable local codes.

Continued

®

VENTED NATURAL GAS LOGS

AIR FOR
COMBUSTION AND
VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside
Building

This fresh air would come from an adjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must pro­vide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see op­tion 3, Figure 2). Follow the National Fuel

Gas Code, NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

WARNING: Rework work­sheet, adding the space of the
adjoining unconfined space. The
combined spaces must have
enough fresh air to supply all
appliances in both spaces.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation
grills or ducts. You must provide two per­manent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
or spaces open to the outdoors. These spaces
include attics and crawl spaces. Follow the

National Fuel Gas Code, NFPA 54/ANS
Z223.1, Section 5.3, Air for Combustion and
Ventilation for required size of ventilation

grills or ducts.

IMPORTANT:

inlet or outlet air into attic if attic has a
thermostat-controlled power vent. Heated air
entering the attic will activate the power vent.

Do not provide openings for

Ventilation

Grills

Into Adjoining

Room,

Option 1

Figure 2 - Ventilation Air from Inside Building

Or

Remove
Door into
Adjoining

Room,
Option

3

12"

Outlet
Air

Ventilation Grills

Into Adjoining Room,

Ventilated
Attic

Outlet
Air

Inlet
Air

Inlet Air

Figure 3 - Ventilation Air from Outdoors

Crawl Space

12"

Option 2

To Attic

To

Crawl

Space

Ventilated

6

901847

OWNER’S MANUAL

INSTALLATION

CAUTION: Do not remove
the metal data plates attached
to the burner pan. The data plates
contain important warranty in­formation.

WARNING: Before installing
in a solid fuel burning fireplace,
the chimney flue and firebox must
be cleaned of soot, creosote,
ashes and loose paint by a quali­fied chimney cleaner. Creosote
will ignite if highly heated. A dirty
chimney flue may create and dis­tribute soot within the house. In­spect chimney flue for damage.

NOTICE: Installation, service, and
repair of this appliance must be
performed by a qualified installer,
service agency, company or gas
supplier experienced with this
type of gas appliance. Only fac­tory authorized components listed
in these instructions may be used
in accordance with the
manufacturer’s instructions and
all codes and requirements of the
authority having jurisdiction. Any
modifications to this kit, or use of
unauthorized components or ac­cessory items will void the
manufacturer’s warranty, and may
result in a hazardous condition.

FLUE OPENING
SPECIFICATIONS

Note:

This vented appliance must be in-

stalled only in a solid-fuel burning fireplace
with a working flue and constructed of non­combustible material.

The charts in Figure 4 indicate technical
information regarding the installation of
your gas log set. Please make sure that all of
the specifications shown are applicable be­fore installation is attempted.

The fireplace must include a working flue
and venting system with the minimum open­ings shown in the Figure 4.

Btu Input

MODEL DESCRIPTION

VVTR18 18" Triple Burner 60,000 50,000 8" dia.
VVTR24 24" Triple Burner 70,000 60,000 8" dia.

MINIMUM FIREBOX SIZES

LOG FRONT BACK
SIZE WIDTH* WIDTH** DEPTH HEIGHT

18" 28" 16" 14" 18"
24" 29 3/4" 17" 15 1/2" 18"

*Add 2" if safety valve/pilot is used
**At depth indicated

FUEL INLET PRESSURE

SPECIFICATIONS ("W.C.)

Min. Max.
NG 5.5 10.5
LP 11 13

Figure 4 - Technical Information Charts

CHECK GAS TYPE

Use only natural gas. If your gas supply is not
natural gas, you must install ON/OFF Safety
Valve/Pilot Kit (see Accessories, page 17).
Call dealer where you bought log set.

If the fireplace does not have a gas supply
shutoff valve, one must be installed.

Natural Gas

LOG NATURAL PROPANE/LP
SIZE

FRONT REAR FRONT REAR

18" .046 4x.064 .036 4x.043
24" .064 4x.064 .036 4x.0465

VENTING SPECIFICATIONS
FOR INSTALLATION

The fireplace chimney flue and vent must be
drafting properly. To check the vent for
proper drafting: Light a tightly rolled news­paper on one end and place it at the inside
front edge of the fireplace. Observe the
smoke and be sure the vent is properly
drawing it up the chimney. If the smoke
spills out into the room, extinguish the flame
and remove any obstruction until proper
venting is achieved.

The chimney flue must remain open a mini­mum of 3" at all times during the operation
of this log set.

Btu Input

Propane Gas

BURNER ORIFICE

Minimum

Vent Opening

Continued

901847

7