Desa Proflame Series, Proflame LMFP33 Series, Proflame LDL39 Series Operation

Desa Heating LLCDesa Heating LLC

Proflame Series OperationProflame Series Operation

Control ComponentsControl Components

Desa Proflame units, LMFP33 and LDL39 series
have two integral control components – the remote
and the receiver unit.

Remote ControlRemote Control

nn Allows adjustment of BTU Allows adjustment of BTU

output (flame height)output (flame height)

nn Allows thermostatic Allows thermostatic

operation of the heater.operation of the heater.

nn Allows sleep timer Allows sleep timer

operation in 15 minute operation in 15 minute

intervals up to 90 minutes.intervals up to 90 minutes.

Remote (cont.)Remote (cont.)

nn BTU/Flame BTU/Flame

height controlheight control

nn Thermostatic Thermostatic

FunctionFunction

nn Timer functionTimer function

nn IndicatorIndicator

Remote (cont.)Remote (cont.)

nn U ses th ree “A A A ” U ses th ree “A A A ”

batteries.batteries.

nn Programmable Programmable

addresses to avoid addresses to avoid
conflict with other conflict with other
remote devicesremote devices

ReceiverReceiver

nn Connects to gas valve Connects to gas valve

stepper motor to stepper motor to

control BTU output.control BTU output.

nn Dip switches to control Dip switches to control

address (must match address (must match

with corresponding with corresponding

remote).remote).

nn Auto/Man switch to Auto/Man switch to

allow for nonallow for non--remote remote

operationoperation

Receiver (cont.)Receiver (cont.)

nn Pow ered b y fou r “A A ” Pow ered b y fou r “A A ”

batteries.batteries.

nn Beep codes to indicate Beep codes to indicate

“w orking ” or “low “w orking ” or “low
battery.”battery.”

TroubleshootingTroubleshooting

nn If the remote does If the remote does

not come on when not come on when

the power button is the power button is

pressed, replace pressed, replace
the batteries. If the batteries. If

the problem the problem

persists, call 1persists, call 1--866866-­672672--6040 with your 6040 with your

model and serial # model and serial #

handy.handy.

Troubleshooting (cont.)Troubleshooting (cont.)

nn IF the remote IF the remote

appears to be appears to be

working, but you get working, but you get

no reaction from the no reaction from the
heater:heater:

1) Check the 1) Check the
batteries in the batteries in the

receiver and replace receiver and replace

as neededas needed

Troubleshooting (cont.)Troubleshooting (cont.)

2) Check the dip2) Check the dip--switchswitch
settings on the receiver:settings on the receiver:

a.a. Locate the receiver in Locate the receiver in

your heater.your heater.

b.b. Remove the receiver and Remove the receiver and

turn to the side with the turn to the side with the

eight dip switches, labeled eight dip switches, labeled

“add ress.”“add ress.”

c.c. C h eck that sw itches “1” C h eck that sw itches “1”

and “3” are u p w h ile th e and “3” are u p w h ile th e

rest are downrest are down

d.d. Remove one battery for Remove one battery for

fifteen seconds and fifteen seconds and
replace in order to reset replace in order to reset
the receiver. the receiver.

Troubleshooting (cont.)Troubleshooting (cont.)

3) Check the code in the 3) Check the code in the
remote by: remote by:

a.a. Move the indicator to Move the indicator to

the timer using the the timer using the
down button.down button.

b.b. Press the minus Press the minus

button ten times or button ten times or

until the remote goes until the remote goes
blank.blank.

c.c. Press the up or down Press the up or down

key to change the key to change the

given co d e to “005”.given code to “005”.

d.d. Press the minus key Press the minus key

once more.once more.

Troubleshooting (cont.)Troubleshooting (cont.)

nn If everything seems If everything seems

to be working and to be working and

yet the unit still yet the unit still

does not operate, does not operate,
check the wiring check the wiring

from the receiver to from the receiver to

the valve. Look for the valve. Look for
any exposed wire, any exposed wire,

breaks, or burns.breaks, or burns.

Troubleshooting (cont.)Troubleshooting (cont.)

If th e rem ote is show ing “A U X ” If th e rem ote is show ing “A U X ”

a.a. Move the indicator to the Move the indicator to the

timer using the down timer using the down

buttonbutton

b.b. Press the minus button Press the minus button

ten times or until the ten times or until the

remote goes blank remote goes blank –– the the

remote enters setremote enters set--up modeup mode..

c.c. Press the ON/OFF button Press the ON/OFF button

five times five times -- this removes the this removes the

“AU X ” Fu nctions“AU X ” Fu nctions..

d.d. Press the minus button Press the minus button

once more once more –– this returns the this returns the

remote to normal operationremote to normal operation

Troubleshooting (cont.)Troubleshooting (cont.)

If the remote is in Celsius If the remote is in Celsius

a.a. Move the indicator to Move the indicator to

the timer using the the timer using the
down button.down button.

b.b. Press the minus Press the minus

button ten times or button ten times or

until the remote goes until the remote goes
blank.blank.

c.c. Press the plus button Press the plus button

once.once.

d.d. Press the minus Press the minus

button once morebutton once more