Shown with optional
cabinet mantel and
hearth base.
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a
qualified installer, service agency, or the gas supplier.
This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile) home, where not prohibited by state or local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
WARNING: Improper installation,
adjustment, alteration, service,
or maintenance can cause injury
or property damage. Refer to this
manual for correct installation
and operational procedures. For
assistance or additional information consult a qualified installer, service agency, or the
gas supplier.
WARNING: This is an unvented
gas-fired heater. It uses air (oxygen) from the room in which it is
installed. Provisions for adequate
combustion and ventilation air
must be provided. Refer to
Combustion and Ventilation
tion on page 4 of this manual.
Air for
sec-
Save this manual for future reference.
Page 2
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
SAFETY
INFORMATION
WARNINGS
IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, operate,
or service this fireplace. Improper
use of this fireplace can cause serious injury or death from burns,
fire, explosion, electrical shock, and
carbon monoxide poisoning.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning:Early signs
of carbon monoxide poisoning resemble the
flu, with headaches, dizziness, or nausea. If
you have these signs, the fireplace may not
be working properly. Get fresh air at once!
Have fireplace serviced. Some people are
more affected by carbon monoxide than
others. These include pregnant women,
people with heart or lung disease or anemia,
those under the influence of alcohol, and
those at high altitudes.
Natural Gas: Natural gas is odorless. An
odor-making agent is added to the gas. The
odor helps you detect a gas leak. However,
the odor added to the gas can fade. Gas may
be present even though no odor exists.
Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this fireplace.
WARNING: Any change to this
heater or its controls can be
dangerous.
WARNING: Do not allow fans
to blow directly into the fireplace.
Avoid any drafts that alter burner
flame patterns. Ceiling fans can
create drafts that alter burner
flame patterns. Altered burner
patterns can cause sooting.
WARNING: Do not use a
blower insert, heat exchanger
insert, or other accessory not approved for use with this heater.
Due to high temperatures, the
appliance should be located out
of traffic and away from furniture
and draperies.
Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.
Fireplace front and screen becomes very hot when running
fireplace. Keep children and
adults away from hot surfaces to
avoid burns or clothing ignition.
Fireplace will remain hot for a
time after shutdown. Allow surfaces to cool before touching.
Carefully supervise young children when they are in the room
with heater. When using the handheld remote accessory, keep selector switch in the OFF position
to prevent children from turning
on burners with remote.
You must operate this fireplace
with the fireplace screen and
hood in place. Make sure fireplace screen and hood are in
place before running fireplace.
Keep the appliance area clear and
free from combustible materials,
gasoline, and other flammable
vapors and liquids.
1.This appliance is only for use with the
type of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases.
2.If you smell gas
• shut off gas supply
• do not try to light any appliance
•
do not touch any electrical switch; do
not use any phone in your building
• immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions
• if you cannot reach your gas supplier,
call the fire department
3.This fireplace shall not be installed in
a bedroom or bathroom.
4.Do not use this fireplace as a woodburning fireplace. Use only the logs
provided with the fireplace.
5.Do not add extra logs or ornaments
such as pine cones, vermiculite, or rock
wool. Using these added items can
cause sooting. Do not add lava rock
around base. Rock and debris could fall
into the control area of fireplace.
6.This fireplace is designed to be smokeless. If logs ever appear to smoke, turn
off fireplace and call a qualified service person.
eration, slight smoking could occur due
to log curing and fireplace burning
manufacturing residues.
7.T o prevent the creation of soot, follow
the instructions in Cleaning and Main-tenance, page 18.
8.Before using furniture polish, wax, carpet cleaner, or similar products, turn
heater off. If heated, the vapors from
these products may create a white powder residue within burner box or on
adjacent walls or furniture.
9.This fireplace needs fresh air ventilation to run properly . This fireplace has
an Oxygen Depletion Sensing (ODS)
safety shutoff system. The ODS shuts
down the fireplace if not enough fresh
air is available. See Air for Combus-tion and Ventilation, pages 4 through
6. If fireplace keeps shutting off, see
Troubleshooting, pages 19 through 21.
10. Do not run fireplace
• where flammable liquids or vapors
are used or stored
• under dusty conditions
11. Do not use this fireplace to cook food
or burn paper or other objects.
12. Do not use fireplace if any part has been
exposed to or under water. Immediately
call a qualified service technician to
inspect the fireplace and to replace any
part of the control system and any gas
control which has been under water.
13. Do not operate fireplace if any log is
broken. Do not operate fireplace if a
log is chipped (dime-sized or larger).
14. Turn fireplace off and let cool before
servicing. Only a qualified service person should service and repair fireplace.
15. Operating fireplace above elevations of
4,500 feet could cause pilot outage.
Note:
During initial op-
2
107063
Page 3
OWNER’S MANUAL
PRODUCT
IDENTIFICATION
I
H
L
O
O
F
F
N
O
P
I
T
L
Control
Knobs
Piezo
Ignitor
Remote Selector
Switch (Optional)
Figure 1 - Log Base Assembly
Top Louvered
Hood
Firebox
Support
O
Log Set
Optional Remote
Control
Top Outer
Casing
LOCAL CODES
Install and use fireplace with care. Follow all
local codes. In the absence of local codes, use
the latest edition of The National Fuel GasCode, ANS Z223.1, also known as NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
UNPACKING
1.With utility knife, cut the carton all the
way around above the staples on the
bottom tray. Lift the carton off the
heater. Remove packing.
Note:
The
hood is located in the packing on the
right hand side of the heater front. Lift
the heater off the bottom tray.
2.Locate two screws above top corners
of the fireplace screen. Remove and
discard these screws. Lift fireplace
screen up and pull out to remove.
3.Remove protective packaging applied
to logs, log base assembly, and fireplace.
4.Check all items for any shipping damage. If damaged, promptly inform
dealer where you bought fireplace.
REMOTE CONTROL
Screen
Assembly
Figure 2 - Fireplace
107063
ACCESSORIES
The remote controls that can be purchased
separately for this log heater are hand held
remotes. See Accessories, pages 24 and 25.
Rear
Access
Door
Bottom Louver
Assembly
3
Page 4
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
PRODUCT
FEATURES
OPERATION
This vent-free fireplace is clean burning. It
requires no outside venting. There is no heat
loss out a vent or up a chimney. Heat is
generated by both realistic flames and glowing embers. When used without the blower,
the fireplace requires no electricity making
it ideal for emergency backup heat.
SAFETY DEVICE
This fireplace has a pilot with an Oxygen
Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for
vent-free room heaters. The ODS system
shuts off the fireplace if there is not enough
fresh air.
PIEZO IGNITION SYSTEM
This fireplace has a piezo ignitor. This system requires no matches, batteries, or other
sources to light fireplace.
BLOWER ASSEMBLY
(GA3750 and GA3650T Series)
This fireplace accepts an optional blower
assembly. The GA3750 blower has a manual
variable control. The GA3650T blower operates thermostatically. The blower circulates heated air from the fireplace into the
room. Use of blower is optional. See Acces-sories, pages 24 and 25.
AIR FOR
COMBUSTION AND
VENTILATION
WARNING: This heater shall
not be installed in a confined space
or unusually tight construction
unless provisions are provided
for adequate combustion and ventilation air. Read the following instructions to insure proper fresh
air for this and other fuel-burning
appliances in your home.
Today’s homes are built more energy efficient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home owners
weather strip and caulk around windows and
doors to keep the cold air out and the warm air
in. During heating months, home owners
want their homes as airtight as possible.
While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide adequate fresh air for these appliances. This
will insure proper venting of vented fuelburning appliances.
PROVIDING ADEQUATE
VENTILATION
The following are excerpts from National
Fuel Gas Code, NFPA 54/ANS Z223.1, Section 5.3, Air for Combustion and Ventilation.
All spaces in homes fall into one of the three
following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 6 will
help you classify your space and provide
adequate ventilation.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.
Unusually tight construction is defined as construction where:
a. walls and ceilings exposed to the
outside atmosphere have a continuous water vapor retarder with
a rating of one perm (6 x 10
per pa-sec-m2) or less with openings gasketed or sealed
b. weather stripping has been
added on openable windows and
doors
c. caulking or sealants are applied
to areas such as joints around
window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and
gas lines, and at other openings.
If your home meets all of the three
criteria above, you must provide additional fresh air. See
From Outdoors
If your home does not meet all of the
three criteria above, proceed to
mining Fresh-Air Flow for Fireplace
Location
and
, page 6
on page 5.
Ventilation Air
.
and
Deter-
-11
kg
Confined Space and Unconfined
Space
The National Fuel Gas Code, ANS Z223.1
defines a confined space as a space whose
volume is less than 50 cubic feet per 1,000
Btu per hour (4.8 m3 per kw) of the aggregate
input rating of all appliances installed in that
space and an unconfined space as a space
whose volume is not less than 50 cubic feet
per 1,000 Btu per hour (4.8 m3 per kw) of the
aggregate input rating of all appliances installed in that space. Rooms communicating
directly with the space in which the appliances are installed*, through openings not
furnished with doors, are considered a part of
the unconfined space.
This heater shall not be installed in a confined space of unusually tight construction
unless provisions are provided for adequate
combustion and ventilation air.
* Adjoining rooms are communicating only
if there are doorless passageways or ventilation grills between them.
4
107063
Page 5
OWNER’S MANUAL
AIR FOR
COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills
between the rooms.
1.Determine the volume of the space (length x width x height).
Length x Width x Height = _________________cu. ft. (volume of space)
Example:
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.
2.Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)
Example:
3.Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free fireplace___________________ Btu/Hr
Gas water heater*___________________ Btu/Hr
Gas furnace___________________ Btu/Hr
Vented gas heater___________________ Btu/Hr
Gas fireplace logs___________________ Btu/Hr
Other gas appliances* +___________________ Btu/Hr
Total =___________________ Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
4.Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)
Example:
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework work sheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-
ing room or add ventilation grills between rooms. See Ventilation Air from Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air from Outdoors, page 6.
C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
Space size 22 ft. (length) x 18 ft. (width) x 8 ft. (ceiling height) = 3168 cu. ft. (volume of space)
3168 cu. ft. (volume of space) ÷ 50 cu. ft. = 63.3 or 63,300 (maximum Btu/Hr the space can support)
Example:
Gas water heater
Vent-free fireplace +
Total=
63,300 Btu/Hr (maximum the space can support)
73,000 Btu/Hr (actual amount of Btu/Hr used)
40,000
33,000
73,000
Btu/Hr
Btu/Hr
Btu/Hr
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of
the methods described in the
107063
National Fuel Gas Code, ANS Z223.1, Section 5.3
5
or applicable local codes.
Continued
Page 6
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
AIR FOR
COMBUSTION AND
12"
VENTILATION
Continued
VENTILATION AIR
Ventilation Air From Inside
Building
This fresh air would come from an adjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must provide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 3). You can also
remove door into adjoining room (see option 3, Figure 3). Follow the National Fuel
Gas Code, NFPA 54/ANS Z223.1, Section
5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
WARNING: Rework worksheet, adding the space of the
adjoining unconfined space. The
combined spaces must have
enough fresh air to supply all
appliances in both spaces.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation
grills or ducts. You must provide two permanent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
or spaces open to the outdoors. These spaces
include attics and crawl spaces. Follow the
National Fuel Gas Code, NFPA 54/ANS
Z223.1, Section 5.3, Air for Combustion
and Ventilation for required size of ventila-
tion grills or ducts.
IMPORTANT:
inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent.
Do not provide openings for
Ventilation
Grills
Into Adjoining
Room,
Option 1
Figure 3 - Ventilation Air from Inside Building
Or
Remove
Door into
Adjoining
Room,
Option
3
12"
Outlet
Air
Ventilation Grills
Into Adjoining Room,
Option 2
Ventilated
Attic
Outlet
Air
Inlet
Air
Inlet Air
Figure 4 - Ventilation Air from Outdoors
Ventilated
Crawl Space
To Attic
To
Crawl
Space
6
107063
Page 7
OWNER’S MANUAL
INSTALLATION
NOTICE: This heater is intended
for use as supplemental heat. Use
this heater along with your primary heating system. Do not install this heater as your primary
heat source. If you have a central
heating system, you may run
system’s circulating blower while
using heater. This will help circulate the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.
WARNING: A qualified service person must install fireplace.
Follow all local codes.
WARNING: Never install the
fireplace
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objects are less than 42 inches
from the front, top, or sides of
the fireplace
• in high traffic areas
• in windy or drafty areas
CAUTION: This fireplace creates warm air currents. These currents move heat to wall surfaces
next to fireplace. Installing fireplace next to vinyl or cloth wall
coverings or operating fireplace
where impurities (such as tobacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.
Note:
Your Comfort Glow fireplace is de-
signed to be used in zero clearance installations. Wall or framing material can be placed
directly against any exterior surface on the
rear, sides, or top of your fireplace, except
where standoff spacers are integrally attached. If standoff spacers are attached to
your fireplace, these spacers can be placed
directly against wall or framing materials.
Use the dimensions shown for rough openings to create the easiest installation (see
Built-In Fireplace Installation, page 9).
IMPORTANT:
ture to the air. Although this is beneficial,
installing fireplace in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-bustion and Ventilation, pages 4 through 6.
IMPORTANT:
level. If fireplace is not level, log set will not
work properly.
Vent-free heaters add mois-
Make sure the fireplace is
CHECK GAS TYPE
Use only natural gas. If your gas supply is
not natural gas, do not install fireplace. Call
dealer where you bought fireplace for proper
type fireplace.
ELECTRICAL HOOKUP
(Optional Blower Accessory)
This fireplace accepts a blower assembly
with an electrical cord. The electrical cord is
five feet in length. You must locate fireplace
within reach of a 120 volt grounded electrical outlet. If not, you must install an electrical outlet within reach of fireplace power
cord.
ASSEMBLING AND
ATTACHING OPTIONAL
BRASS TRIM
(Included with Mantel
Accessory)
IMPORTANT:
box in a wall, do not attach brass trim at this
time. See page 9.
Note:
The instructions below show assem-
bling and attaching brass trim to fireplace.
1.Remove packaging from three pieces
of brass trim.
2.Locate four brass screws, two adjusting plates with set screws, and two
shims in the hardware packet.
3. Align shim under adjusting plate as
shown in Figure 5.
4.Slide one end of adjusting plate/shim
in slot on mitered edge of top brass trim
(see Figure 5).
5.Slide other end of adjusting plate/shim
in slot on mitered edge of side brass
trim (see Figure 5).
If you are recessing the fire-
6. While firmly holding edges of brass
trim together, tighten both set screws
on the adjusting plate with slotted
screwdriver.
7.Repeat steps 1 through 6 for other side.
8. Tighten trim hanging screws (#10 x
6.25 shoulder) into holes in cabinets.
Place the assembled trim onto fireplace
cabinet. Align hanging notches on trim
with hanging screws on side of fireplace (see Figure 6). Push trim firmly
into place, sliding hanging notches over
hanging screws.
Set Screws
Side Brass
Trim
Figure 5 - Assembling Brass Trim
Figure 6 - Attaching Brass Trim to
Fireplace
Adjusting
Plate
Mitered Edge
Slot
Assembled
Brass Trim
Shim
Slot
Top
Brass
Trim
Trim
Hanging
Screws
Hanging
Notches
on Trim
Continued
107063
7
Page 8
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
INSTALLATION
Continued
INSTALLATION
CLEARANCES
WARNING: Maintain the minimum clearances. If you can, provide greater clearances from
floor, ceiling, and adjoining wall.
Carefully follow the instructions below. This
will ensure safe installation.
Minimum Clearances For Side
Combustible Material, Side Wall,
and Ceiling
A. Clearances from the side of the fire-
place cabinet to any combustible material and wall should follow diagram
in Figure 7.
Example:
shelf, etc. is made of combustible material and protrudes 3 1/2" from the wall.
This combustible material must be 4"
from the side of the fireplace cabinet
(see Figure 7).
B. Clearances from the top of the fireplace
opening to the ceiling should not be less
than 42 inches.
FIREBOX
*Minimum 16 inches from Side Wall
Figure 7 - Minimum Clearance for
Combustible to Wall
The face of a mantel, book-
Example
.52
14 6 8 10 12 14 16
INCHES
121/
101/
8
7
51/
31/
1
7/8
7/16
*
4
2
3
/
4
4
2
3
/
4
CONVENTIONAL FIREPLACE
INSTALLATION
Conventional installation of this fireplace
involves installing fireplace along with the
corner, face, or cabinet mantel with hearth
base accessories against a wall in your home.
Follow the instructions below to install the
fireplace in this manner.
Note:
The instructions below show installation using the cabinet mantel and hearth
base accessories (see Accessories, pages 24
and 25). The hearth base accessory shown is
optional for this installation. You can install
fireplace and cabinet mantel directly on the
floor. The corner mantel accessory cannot
be installed with the hearth bases. You must
install corner mantel directly on the floor.
1.Assemble cabinet mantel, hearth base,
and trim accessories. Assembly instructions are included with each accessory .
2.When installing blower, install a prop-
erly grounded, 120 volt three-prong
electrical outlet at fireplace location if
an outlet is not there. If possible, locate outlet so cabinet mantel will cover
it when installed (see Figure 8).
3.Install gas piping to fireplace location.
This installation includes an approved
flexible gas line (if allowed by local
codes) after the equipment shutoff
valve. The flexible gas line must be the
last item installed on the gas piping. See
Installing Gas Piping to Fireplace Location, page 10.
4. Place hearth base accessory against
INCHES
wall at installation location. Cut an access hole in hearth top to run flexible
gas line to fireplace (see Figure 8).
Make sure to locate access hole so cabinet mantel will cover it when installed.
Note:
You can secure base to floor using wood screws. Countersink screw
heads and putty over.
5.Route flexible gas line through access
hole in hearth base.
6.Center cabinet mantel on hearth base
(see Figure 9). Make sure mantel is
flush against wall.
7.Break off nailing flanges (see Figure 10,
page 9) with hammer or pliers.
8. Place cardboard or other protective
material on top of hearth base. Carefully set fireplace on protective material, with back of fireplace inside mantel opening.
9.Attach flexible gas line to fireplace gas
regulator. See Connecting Fir eplace toGas Supply, page 11.
10. If blower is installed, route blower electrical cord through access holes in either side of fireplace.
Note:
Bushing
may be moved if necessary. Plug electrical cord into electrical outlet.
Hearth
Base
Figure 8 - Placing Hearth Base Accessory
Against Wall
Figure 9 - Installing Cabinet Mantel
Flexible
Gas Line
Electrical
Outlet
Gas Line
Access
Hole
Cabinet
Mantel
8
107063
Page 9
OWNER’S MANUAL
INSTALLATION
Continued
11. Carefully insert fireplace into cabinet
mantel. Be careful not to scratch or
damage hearth base, cabinet mantel, or
any laminate trim on hearth base. Remove protective material from top of
hearth base and from front of fireplace
(if any).
to hearth or floor. Open lower louver.
Locate screw holes in bottom of base.
Tighten wood screws through these
holes and into hearth or floor.
12. Check all gas connections for leaks. See
Checking Gas Connections, page 12.
Figure 10 - Location of Nailing Flanges
Figure 11 - Inserting Fireplace Into Cabinet
Mantel
Note:
You can secure fireplace
Nailing
Flanges
BUILT-IN FIREPLACE
INSTALLATION
Built-in installation of this fireplace involves
installing fireplace into a framed-in enclosure. This makes the front of fireplace flush
with wall. If installing a mantel above the
fireplace, you must follow the clearances
shown in Figure 15, page 10 . Follow the
instructions below to install the fireplace in
this manner.
ActualFraming
3
Height32
Front Width 34
Depth16
1.Frame in rough opening. Use dimensions shown in Figure 12 for the rough
opening.
If installing in a corner, use dimensions shown in Figure 13 for the rough
opening. The height is 33" which is
the same as the wall opening above.
2.If using blower, install and properly
ground GA3555, three-prong 120 volt
electrical outlet, in fireplace. Follow
instructions included in kit (see Acces-sories, pages 24 and 25).
3.Install gas piping to fireplace location.
This installation includes an approved
flexible gas line (if allowed by local
codes) after the equipment shutoff
valve. The flexible gas line must be
the last item installed on the gas piping. See Installing Gas Piping to Fire-place Location, page 10.
4. Carefully set fireplace in front of
rough opening with back of fireplace
inside wall opening.
5.Attach flexible gas line to gas supply .
See Connecting Fireplace to Gas Sup-ply, page 11.
6.Plug electrical cord into electrical outlet installed in step 2.
7.Carefully insert fireplace into rough
opening.
8.Attach fireplace to wall studs using
nails or wood screws through holes in
nailing flange (see Figure 14).
/8"33"
5
/16"35 1/2"
11
/16"17 3/4"
9.Check all gas connections for leaks. See
Checking Gas Connections, page 12.
10. Install brass trim after final finishing
and/or painting of wall (see Figure 6,
page 7).
17 3/4"
33"
35 1/2"
Figure 12 - Rough Opening for Installing
in Wall
39 3/8"
27 7/8"
35 1/2"
55 5/8"
Figure 13 - Rough Opening for Installing
in Corner
Nails or
Wood
Screws
Nailing Flanges
Figure 14 - Attaching Fireplace to Wall
Studs
107063
Continued
9
Page 10
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
INSTALLATION
Continued
Mantel Clearances for Built-In
Installation
If placing mantel above built-in fireplace,
you must meet minimum clearance between
mantel shelf and top of fireplace opening.
NOTICE: Surface temperatures of
adjacent walls and mantels become hot during operation. Walls
and mantels above the firebox
may become hot to the touch. If
installed properly, these temperatures meet the requirement of the
national product standard. Follow all minimum clearances
shown in this manual.
Wall board or facing
material (above
firebox) may be of
combustible material,
including decorative
mantel ornaments or
other similar projections off of the facing
material.
Framing
Material
Firebox
10"
8"
6"
2
1
/2
NOTICE: If your installation does
not meet the minimum clearances
shown, you must do one of the
following:
• raise the mantel to an acceptable height
• remove the mantel
Mantel Shelf
"
Noncombustible
Material May
Project Off this
Surface above
the Firebox Hood
INSTALLING GAS PIPING TO
FIREPLACE LOCATION
WARNING: A qualified service person must connect fireplace to gas supply. Follow all
local codes.
Installation Items Needed
Before installing fireplace, make sure you
have the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by local codes) (not
provided)
* A CSA design-certified equipment shutoff
valve with 1/8" NPT tap is an acceptable
alternative to test gauge connection. Purchase the optional CSA design-certified
equipment shutoff valve from your dealer.
See Accessories, pages 24 and 25.
WARNING: Never connect
fireplace to private (non-utility)
gas wells. This gas is commonly
known as wellhead gas.
13" 16" 19" 21"
Wire-mesh
Screen
Figure 15 - Minimum Mantel Clearances for Built-In Installation
Supplied Firebox
Hood Must Be
Used at All Times
Note:
measurements are
from top of fireplace
hood opening to bottom
of mantel shelf.
These minimum
clearances replace any
other recommended
clearances supplied with
your ANS Z21.11.2
approved gas logs.
All vertical
10
CAUTION: Use only new,
black iron or steel pipe. Internally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of 1/2"
diameter or greater to allow
proper gas volume to fireplace. If
pipe is too small, undue loss of
pressure will occur.
107063
Page 11
OWNER’S MANUAL
INSTALLATION
Continued
CONNECTING FIREPLACE
TO GAS SUPPLY
Installation must include an equipment
shutoff valve, union, and plugged 1/8" NPT
tap. Locate NPT tap within reach for test
gauge hook up. NPT tap must be upstream
from fireplace (see Figure 16).
IMPORTANT:
valve in an accessible location. The equipment shutoff valve is for turning on or
shutting off the gas to the appliance.
Check your building codes for any special
requirements for locating equipment shutoff
valve to fireplaces.
Apply pipe joint sealant lightly to male
threads. This will prevent excess sealant
from going into pipe. Excess sealant in pipe
could result in clogged fireplace valves.
CAUTION: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.
We recommend that you install a sediment
trap in supply line as shown in Figure 16.
Locate sediment trap where it is within
reach for cleaning. Install in piping system
between fuel supply and heater. Locate sediment trap where trapped matter is not likely
to freeze. A sediment trap traps moisture
Install equipment shutoff
CSA DesignCertified Equipment
Shutoff Valve With
1/8" NPT Tap*
and contaminants. This keeps them from
going into fireplace gas controls. If sediment trap is not installed or is installed
wrong, fireplace may not run properly.
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• Phillips screwdriver
• sealant (resistant to propane/LP gas, not
provided)
1.Remove fireplace screen. Remove two
screws that hold fireplace screen in
place for shipping. These screws are
located near top of screen. Discard
screws. Lift fireplace screen up and pull
out to remove.
2. Remove screws that attach log base
assembly to fireplace (see Figure 17).
Carefully lift up log base assembly and
remove from fireplace (see Figure 17).
CAUTION: Do not pick up log
base assembly by burners. This
could damage burners. Only
handle base by grates.
3.Route gas line (provided by installer)
from equipment shutoff valve to fireplace. Route flexible gas supply line
through one of the access holes.
NOTICE: Most building codes do
not permit concealed gas connections. A flexible gas line is
provided to allow accessibility
from the fireplace (see Figure 18).
The flexible gas supply line connection to the equipment shutoff
valve should be accessible.
4.Attach the flexible gas line to gas supply (see Figure 18). Check tightness of
flexible gas line attached to gas regulator of fireplace (see Figure 18).
5.Check all gas connections for leaks. See
Checking Gas Connections, page 12.
6.Replace log base assembly back into
fireplace. Feed flexible gas line into fireplace base area while replacing log base
assembly. Make sure the entire flexible
gas line is in fireplace base area. Reattach log base assembly to fireplace with
screws removed in step 2.
To Fireplace
Gas Regulator
➞
Equipment
Shutoff Valve
Provided by
Installer
Flexible Gas
Line from
Fireplace Gas
Regulator
➞
To Gas
Meter
3" Minimum
From Gas
Meter (5"
Pipe Cap Tee
NippleJoint
Sediment Trap
W.C. to
10.5" W.C.
Pressure)
Figure 16 - Gas Connection
* Purchase the optional CSA design-certified equipment shutoff valve from your
dealer. See Accessories, pages 24 and 25
107063
I
H
L
O
O
F
F
N
O
P
T
I
L
O
Figure 17 - Removing Log Base Assembly
From Fireplace
11
Figure 18 - Attaching Gas Lines Together
Continued
Page 12
LFP33NRA
ON
POSITION
OFF
POSITION
UNVENTED NATURAL GAS FIREPLACE
INSTALLATION
Continued
CHECKING GAS
CONNECTIONS
WARNING: Test all gas piping and connections for leaks
after installing or servicing. Correct all leaks at once.
WARNING: Never use an open
flame to check for a leak. Apply a
mixture of liquid soap and water
to all joints. Bubbles forming show
a leak. Correct all leaks at once.
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
1.Disconnect appliance with its appliance
main gas valve (control valve) and
equipment shutoff valve from gas supply piping system. Pressures in excess
of 1/2 psig will damage fireplace gas
regulator.
2. Cap off open end of gas pipe where
equipment shutoff valve was connected.
3.Pressurize supply piping system by either using compressed air or opening
main gas valve located on or near gas
meter.
4.Check all joints of gas supply piping
system. Apply mixture of liquid soap
and water to gas joints. Bubbles forming show a leak.
5.Correct all leaks at once.
6. Reconnect fireplace and equipment
shutoff valve to gas supply. Check reconnected fittings for leaks.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1.Close equipment shutoff valve (see Figure 19).
2.Pressurize supply piping system by either using compressed air or opening
main gas valve located on or near gas
meter.
3. Check all joints from gas meter to
equipment shutoff valve (see Figure
20). Apply mixture of liquid soap and
water to gas joints. Bubbles forming
show a leak.
4.Correct all leaks at once.
Open
Equipment
Shutoff
Valve
Closed
Figure 19 - Equipment Shutoff Valve
Manual Gas Valve
Figure 20 - Checking Gas Joints
Pressure Testing Fireplace Gas
Connections
1.Open equipment shutoff valve (see Figure 19).
2.Open main gas valve located on or near
gas meter.
3.Make sure control knob of fireplace is
in the OFF position.
4.Check all joints from equipment shutoff
valve to thermostat gas valve (see Figure 20). Apply mixture of liquid soap
and water to gas joints. Bubbles forming show a leak.
5.Correct all leaks at once.
6. Light fireplace (see Operating Fire-place, pages 16 and 17). Check all other
internal joints for leaks.
7.Turn off fireplace (see To Turn Off Gasto Appliance, page 17).
Equipment
Shutoff
Valve
Gas Meter
12
107063
Page 13
OWNER’S MANUAL
INSTALLATION
Continued
INSTALLING LOGS
WARNING: Failure to position
the parts in accordance with these
diagrams or failure to use only
parts specifically approved with
this heater may result in property
damage or personal injury.
CAUTION: Do not remove the
warning and instruction labels
attached to the heater base assembly. These markings contain
important warranty information.
WARNING: After installation
and periodically thereafter, check
to ensure that no flame comes in
contact with any log. With the
heater set to High, check to see if
flames contact any log. If so, reposition logs according to the
log installation instructions in this
manual. Flames contacting logs
will create soot.
Middle Log (#1)
"U"-shaped
Cutout in
Base
I
H
L
O
O
F
F
N
O
P
I
T
L
O
Burner
Figure 21 - Installing Middle Log (#1)
Back Log (#2)
Peg
Hole in Base
Peg
I
H
L
O
O
F
F
N
O
P
I
T
L
O
Crossover Log (#4)
Peg
I
H
L
O
O
F
F
N
O
P
I
T
L
O
Recess
Figure 24 - Installing Crossover Log (#4)
INSTALLING SCREEN
WARNING: You must operate
this fireplace with the fireplace
screen in place. Make sure fireplace screen is in place before
running fireplace.
Install fireplace screen by slipping notches
of fireplace screen over screws on front of
fireplace (see Figure 25).
Each log is marked with a number. These
numbers will help you identify the log when
installing. It is very important to install these
logs exactly as instructed. Do not modify
logs. Only use logs supplied with heater.
1.Place the base of the middle log (#1) in
the U-shaped slots of the grate base.
The cutout on the right of the middle
log should fit over the burner (see Figure 21). Make sure the front of the
middle log is resting on the tabs of the
grate base and the cutout area is centered over the burner “U” bend.
2.Locate pegs on the bottom of back log
(#2). Slide these pegs into the holes in
the grate base behind the burner (see
Figure 22).
3.Locate the notches in the bottom of the
front log (#3). Place the front log on
the grate fingers. Make sure the notches
of the front log line up with the grate
fingers (see Figure 23).
4.Place crossover log (#4) onto the peg
(right) on back log (#2) and into the recess of the middle log (#1) (see Figure 24).
Figure 22 - Installing Back Log (#2)
Front Log (#3)
Notches
I
H
L
O
O
F
F
N
O
P
I
T
L
O
Grate Fingers
Figure 23 - Installing Front Log (#3)
Notches
Screws for
Mounting Screen
Figure 25 - Installing Fireplace Screen
Continued
107063
13
Page 14
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
INSTALLATION
Continued
OPTIONAL WIRELESS HANDHELD REMOTE CONTROL
ACCESSORY RM4
Installing Remote Receiver Unit
1.Disconnect switch wires from the control valve.
2. Remove screws and nuts attaching
switchplate. Save screws and nuts to
attach receiver.
3.Remove switch plate (see Figure 26).
Discard after removing.
4.Install remote receiver unit onto remote
switch bracket using screws and nuts
removed in step 2. See Figure 27.
5.Route wires through hole in the upper
portion of the switch plate (Figure 27).
Connect wires as shown in Figure 28.
(Black and blue wires are not used for
this application.)
Remote Switch
Bracket
Screw
Ignitor
White Wire
From Receiver
Valve
Red Wire From
Receiver
Figure 28 - Connecting Wires
INSTALLING BATTERIES
FOR RM4
Four AA and two AAA batteries (not included) are required to operate this heater
with the wireless hand held remote control
set. AA batteries must be installed in the
receiver and AAA batteries in the hand-held
remote control unit.
line batteries.
Installing Batteries in Receiver
1.Locate back of receiver behind the remote switch bracket under the firebox
bottom.
2.Slide the battery door off of the receiver
in the direction of the arrow on the door.
3.Insert the four AA batteries according
to Figure 29.
4.Slide the battery door back into position.
Note:
Only use alka-
Installing Batteries in Hand-Held
Remote Control Unit
1.Remove battery cover on front of remote control unit following direction
of arrow.
2. Insert two AAA batteries following diagram in battery housing area.
3.Replace battery cover onto remote control unit.
-
+
Remote
Control Unit
+
-
Battery
Housing
AAA
Batteries
Battery
Cover
Figure 30 - Installing Battery in HandHeld Remote Control Unit
Switch Plate
Figure 26 - Switch Plate and Wiring
Harness
Screws
Remote Receiver
Figure 27 - Installing Remote Receiver
Wires
Terminal
Wires
Nuts
+
+
-
-
-
+
+
Remote
Receiver
Battery Door
Figure 29 - Installing Battery in Remote
Receiver
AA Batteries
14
107063
Page 15
OWNER’S MANUAL
INSTALLATION
Continued
OPTIONAL WIRELESS HANDHELD REMOTE CONTROL
ACCESSORY CGHRC AND
CGHRCT SERIES
Installing Remote Receiver Unit
1.Disconnect switch wires from the control valve.
2.Remove screws attaching switchplate.
3.Remove switch plate (see Figure 31).
Discard after removing.
4.Install remote receiver unit onto gas log
heater base using mounting clips.
5.Push clips firmly into place (see Figure 32).
6.Connect wires as shown in Figure 33.
Remote Switch
Bracket
Screw
Ignitor
White Wire
From Receiver
Valve
Red Wire From
Receiver
Figure 33 - Connecting Wires
INSTALLING BATTERIES
FOR CGHRC AND CGHRCT
SERIES
Two 9-volt batteries (not included) are required to operate this heater with the wireless hand held remote control set. Install one
battery in the receiver and one in the handheld remote control unit.
alkaline batteries.
Installing Battery in Receiver
1. Locate back of receiver under front
burner of heater.
2.Locate the battery clip mounted on the
back of the receiver.
3.Slide a 9-volt battery through the clip.
4.Attach the terminal wires to the battery.
Note:
Only use
Installing Battery in Hand-Held
Remote Control Unit
1.Remove battery cover on back of remote control unit.
2. Attach terminal wires to the battery.
Place battery into the battery housing.
3.Replace battery cover onto remote control unit.
Terminal
Wires
9-Volt
Battery
Figure 35 - Installing Battery in HandHeld Remote Control Unit
Battery
Cover
Remote
Control Unit
Battery
Housing
Switch Plate
Figure 31 - Switch Plate and Wiring
Harness
Mounting
Clips
Remote Receiver
Figure 32 - Installing Remote Receiver
107063
Wires
Remote
Receiver
Terminal Wires
Battery Clip
9-Volt Battery
Figure 34 - Installing Battery in Remote
Receiver
15
Page 16
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
OPERATING
FIREPLACE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not follow these instructions exactly, a
fire or explosion may result causing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly .
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch;
do not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Ne ver use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been under water.
LIGHTING
INSTRUCTIONS
WARNING: You must operate
this heater with the fireplace
screen in place. Make sure fireplace screen is in place before
running heater.
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Open damper or window to vent
smell. This will only last a few
hours.
1.STOP! Read the safety information,
column 1.
2.Make sure equipment shutoff valve
is fully open.
3.Set switch to OFF position.
WARNING: Burners will come
on automatically within one
minute when the selector switch
is in the ON position after the
pilot is lit.
4.Press in and turn control knob clockwise to the OFF position.
5.Wait f ive (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety information. If you don’t smell gas, go
to the next step.
6.Press in and turn control knob counterclockwise to the PILOT
position. Press in control knob for
five (5) seconds (see Figure 36).
Ignitor Button
I
H
O
F
F
N
P
O
I
L
O
L
O
T
Note:
You may be running this
heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in
for 30 seconds or more. This will allow air to bleed from the gas system.
7.With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
front burner. If needed, keep pressing ignitor button until pilot lights.
Note:
If pilot does not stay lit, contact a qualified service person or gas
supplier for repairs. Until repair s are
made, light pilot with match. T o light
pilot with match, see Manual Light-ing Procedure on page 17.
8.Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
• If control knob does not pop out
when released, contact a qualified
service person or gas supplier for
repairs.
Note:
If pilot goes out, repeat steps
4 through 8.
9. Slightly push in and turn control
knob counterclockwise to
the ON position.
10. Wait one min ute and switch selector
switch to the ON position to light
burners.
11. Set flame adjustment knob to any
level between HI and LO.
CAUTION: Do not try to adjust
heating levels by using the equipment shutoff valve.
AUTO
ON
OFF
Flame Adjustment
Knob
Figure 36 - Control Knob and Ignitor Button Location (Shown as Supplied,
No Control Options)
Control Knob
16
Selector Switch in OFF Position
Continued
107063
Page 17
OWNER’S MANUAL
OPERATING
FIREPLACE
Continued
WARNING: Make sure the
selector switch is in the OFF position when you are away from
home for long periods of time.
Heater will come on automatically with selector switch in the
ON position.
Pilot Burner
Figure 37 - Pilot
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
1.T urn control knob clockwise
to the OFF position.
2a. Set selector switch in the OFF
2b. If Using Optional Hand-Held Re-
mote: Set selector switch in the OFF
position to keep from draining battery .
Shutting Off Burners Only (pilot
stays lit)
You may shut off the burners and keep
the pilot lit by doing one of the following:
• Turn control knob clockwise
to the PILOT position.
• Use remote control manual OFF button.
• Set selector switch in the OFF position.
MANUAL LIGHTING
PROCEDURE
1.Follow steps 1 through 6 under Lighting Instructions, page 16.
2.Depress control knob and light pilot
with match.
3.Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow step 9, page 16.
Ignitor Electrode
position.
OPTIONAL REMOTE
OPERATION
Note:
All remote control accessories must
be purchased separately (see Accessories,
pages 24 and 25). Follow instructions included with the remote control.
Thermostat Control Operation
The thermostat control setting on the
remote control unit can be set to any
comfort level between HI and LO. The
burners will turn on and off automatically to maintain the comfort level you
select. The ideal comfort setting will vary
by household depending upon the amount
of space to be heated, the output of the
central heating system, etc.
IMPORTANT:
into the hand-held remote. The remote
should be kept several feet from the fireplace and should be pointed towards the
fireplace. If placed too close to the fireplace, the remote will sense the room is
too hot and turn the fireplace off.
OPTIONAL BLOWER
Locate the blower switch by opening lower
louver on fireplace. Blower switch is located at lower right inside louver door.
The GA3650TA Series thermostat-controlled blower has a variable speed control with an ON/OFF switch. The blower
The thermostat is built
OPERATION
will start when the thermostat senses a
NOTICE: You must light the pilot
before using the hand-held remote control unit. See
Instructions
on page 16.
Lighting
After lighting, let pilot flame burn for
about one minute. Turn control knob to
ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide
thee selector switch to the REMOTE position.
Note:
The burners may light if
hand-held remote ON button was on when
selector switch was last turned off. You
can now turn the burners on and off with
the hand-held remote control unit. Follow the instructions supplied with the
remote control for additional features.
IMPORTANT:
Do not leave the selector
switch in the REMOTE position when the
sufficient increase in firebox temperature.
The GA3750 Series variable speed blower
also has an ON/OFF switch built into the
variable speed control.
Note for GA3650TA Series Only:
you are using GA3650TA blower, your
fireplace and blower will not turn on and
off at the same time. The fireplace may
run for several minutes before the blower
turns on. After the heater modulates to
the pilot position, the blower will continue to run. The blower will shut off after
the firebox temperature decreases.
Note:
It is safe to operate fireplace with
blower turned off. However, the blower helps
distribute heated air from the fireplace.
Follow installation instructions included
with the blower accessory.
pilot is not lit. This will drain the battery.
IMPORTANT:
Be sure to press the ON/
OFF buttons on the hand-held remote
control unit for up to 3 seconds to assure
proper operation.
Flame Adjustment Knob
I
H
L
O
Control Knob in
On Position
Figure 38 - Setting the Selector Switch, Control Knob, and Flame
Adjustment Knob for Remote Operation
P
I
L
O
F
T
F
O
O
N
Selector Switch in Remote Position
(Optional Remote Control)
ON
OFF
REMOTE
If
107063
17
Page 18
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
INSPECTING
BURNERS
Check pilot flame pattern and burner flame
patterns often.
PILOT FLAME PATTERN
Figure 39 shows a correct pilot flame pattern. Figure 40 shows an incorrect pilot
flame pattern. The incorrect pilot flame is
not properly heating the thermocouple.
When the thermocouple cools, the heater
will shut down.
If pilot flame pattern is incorrect, as shown
in Figure 40
• turn heater off (see To Turn Off Gas toAppliance, page 17)
•
see Troubleshooting, pages 19 through 21
Pilot Burner
Thermocouple
Figure 39 - Correct Pilot Flame Pattern
Pilot Burner
Thermocouple
Figure 40 - Incorrect Pilot Flame Pattern
MAIN BURNER
Periodically inspect all burner flame holes
with the heater running. All slotted burner
flame holes should be open with yellow
flame present. All round burner flame holes
should be open with a small blue flame
present. Some burner flame holes may become blocked by debris or rust, with no
flame present. If so, turn off heater and let
cool. Either remove blockage or replace
burner. Blocked burner flame holes will
create soot.
CLEANING AND
MAINTENANCE
WARNING: Turn off heater
and let cool before cleaning.
CAUTION: You must keep
control areas, burner, and circulating air passageways of heater
clean. Inspect these areas of
heater before each use. Have
heater inspected yearly by a qualified service person. Heater may
need more frequent cleaning due
to excessive lint from carpeting,
bedding material, pet hair, etc.
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
The primary air inlet holes allow the proper
amount of air to mix with the gas. This provides a clean burning flame. Keep these holes
clear of dust, dirt, lint, and pet hair. Clean these
air inlet holes prior to each heating season.
Blocked air holes will create soot. We recommend that you clean the unit every every three
months during operation and have heater inspected yearly by a qualified service person.
We also recommend that you keep the burner
tube and pilot assembly clean and free of dust
and dirt. To clean these parts we recommend
using compressed air no greater than 30 PSI.
Your local computer store, hardware store, or
home center may carry compressed air in a
can. You can use a vacuum cleaner in the
blow position. If using compressed air in a
can, please follow the directions on the can.
If you don't follow directions on the can, you
could damage the pilot assembly.
1.Shut off the unit, including the pilot. Allow
the unit to cool for at least thirty minutes.
2.Inspect burner, pilot, and primary air
inlet holes on injector holder for dust
and dirt (see Figure 41).
3. Blow air through the ports/slots and
holes in the burner.
4.Check the injector holder located at the
end of the burner tube again. Remove any
large particles of dust, dirt, lint, or pet hair
with a soft cloth or vacuum cleaner nozzle.
5.Blow air into the primary air holes on
the injector holder.
6.In case any large clumps of dust have
now been pushed into the burner repeat
steps 3 and 4.
Clean the pilot assembly also. A yellow tip on
the pilot flame indicates dust and dirt in the pilot
assembly. There is a small pilot air inlet hole
about two inches from where the pilot flame
comes out of the pilot assembly (see Figure 42).
With the unit off, lightly blow air through the air
inlet hole. You may blow through a drinking
straw if compressed air is not available.
Burner
Tube
Primary Air Inlet
Holes (Shape of
Holes May Vary
by Model)
Figure 41 - Injector Holder On Outlet
Burner Tube
Burner
Tube
Pilot
Assembly
Figure 42 - Pilot Inlet Air Hole
Injector Holder
(May Be Brass
or Aluminum
Depending on
Model)
Ports/Slots
Pilot Air
Inlet
Hole
LOGS
• If you remove logs for cleaning, refer to
Installing Logs, page 13, to properly replace logs.
• Replace log(s) if broken or chipped
(dime-sized or larger).
MAIN BURNER
Periodically inspect all burner flame holes
with the heater running. All slotted burner
flame holes should be open with yellow
flame present. All round burner flame holes
should be open with a small blue flame
present. Some burner flame holes may become blocked by debris or rust, with no flame
present. If so, turn off heater and let cool.
Either remove blockage or replace burner.
Blocked burner flame holes will create soot.
18
107063
Page 19
OWNER’S MANUAL
TROUBLESHOOTING
Note:
For additional help, visit DESA
International’s technical service web site
at www.desatech.com.
Note:
All troubleshooting items are listed in
order of operation.
OBSERVED PROBLEM
When ignitor button is pressed, there is no
spark at ODS/pilot
When ignitor button is pressed, there is
spark at ODS/pilot but no ignition
WARNING: Turn off heater
and let cool before servicing. Only
a qualified service person should
service and repair heater.
POSSIBLE CAUSE
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
3. Piezo ignitor nut is loose
4. Broken ignitor cable
5. Bad piezo ignitor
6. Ignitor electrode broken
7. Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in
PILOT position
4. Air in gas lines when installed
5. ODS/pilot is clogged
6. Gas regulator setting is not correct
CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage ODS/
pilot unit.
REMEDY
1. Reconnect ignitor cable
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor to base
panel of log set. Nut is located behind
base panel
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace piezo ignitor
7. Replace piezo ignitor
1. Turn on gas supply or open equipment
shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is
removed
5. Clean ODS/pilot (see Cleaning andMaintenance, page 18) or replace ODS/
pilot assembly
6. Replace gas control
ODS/pilot lights but flame goes out when
control knob is released
107063
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B)
Dirty or partially clogged OD S/pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
www.desatech.com
19
1. Press in control knob fully
2. After ODS/pilot lights, keep control
knob pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural gas company
B) Clean ODS/pilot (see Cleaning andMaintenance, page 18) or replace ODS/
pilot assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace thermocouple
7. Replace control valve
Continued
Page 20
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
Burner does not light after ODS/pilot is lit
Delayed ignition burner
Burner backfiring during combustion
Slight smoke or odor during initial operation
POSSIBLE CAUSE
1. Burner orifice clogged
2. Inlet gas pressure is too low
3. Burner orifice diameter is too small
4. Thermopile leads disconnected or improperly connected
5. Burners will not come on in remote position
1. Manifold pressure is too low
2. Burner orifice clogged
1. Burner orifice is clogged or damaged
2. Damaged burner
3. Gas regulator defective
1. Not enough air
2. Gas regulator defective
3. Residues from manufacturing processes
and logs curing
REMEDY
1. Clean burner (see Cleaning and Maintenance, page 18) or replace burner orifice
2. Contact local natural gas company
3. Replace burner orifice
4. Reconnect leads (see Wiring Diagram,
page 22)
5. Replace battery in transmitter and receiver
1. Contact local natural gas company
2. Clean burner (see Cleaning and Mainte-nance, page 18) or replace burner orifice
1. Clean burner (see Cleaning and Mainte-nance, page 18) or replace burner orifice
2. Replace damaged burner
3. Replace gas control
1. Check burner for dirt and debris. If
found, clean burner (see Cleaning andMaintenance, page 18)
2. Replace gas control
3. Problem will stop after a few hours of
operation
Moisture/condensation noticed on windows
Heater produces a whistling noise when
burner is lit
White powder residue forming within burner
box or on adjacent walls or furniture
Remote does not function
1. Not enough combustion/ventilation air
1. Turning control knob to HI position
when burner is cold
2. Air in gas line
3. Air passageways on heater blocked
4. Dirty or partially clogged burner orifice
1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. turn into
white powder residue
1. Battery is not installed. Battery power
is low
www.desatech.com
20
1. Refer to Air for Combustion and Ventilation requirements (page 4)
1. Turn control knob to LO position and
let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local
natural gas company
3. Observe minimum installation clearances (see pages 8 through 10)
4. Clean burner (see Cleaning and Mainte-nance, page 18) or replace burner orifice
1. Turn heater off when using furniture
polish, wax, carpet cleaners, or similar
products.
1. Replace 9-volt batteries in receiver and
remote control
107063
Page 21
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
OWNER’S MANUAL
IMPORTANT:
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,
etc., create fumes. These fumes may mix with combustion air and create odors. These odors
will disappear over time.
Operating fireplace where impurities in air exist may create odors. Cleaning
OBSERVED PROBLEM
Fireplace produces a clicking/ticking noise
just after burners are lit or shut off
Fireplace produces unwanted odors
Fireplace shuts off in use (ODS operates)
Gas odor even when control knob is in OFF
position
POSSIBLE CAUSE
1. Metal expanding while heating or contracting while cooling
1. Fireplace burning vapors from paint, hair
spray, glues, cleaners, chemicals, new
carpet, etc. (see
above)
2. Gas leak. See Warning statement
above
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
1. Gas leak. See Warning statement
above
2. Control valve defective
IMPORT ANT
statement
REMEDY
1. This is common with most fireplaces. If
noise is excessive, contact qualified service person
1. Open window and ventilate room. Stop
using odor causing products while fireplace is running
2. Locate and correct all leaks (see Check-ing Gas Connections, page 12)
1. Open window and/or door for ventilation
2. Contact local natural gas company
3. Clean ODS/pilot (see Cleaning andMaintenance, page 18)
1. Locate and correct all leaks (see Check-ing Gas Connections, page 12)
2. Replace control valve
Gas odor during combustion
Dark residue on logs or inside of fireplace
107063
1. Foreign matter between control valve
and burner
2. Gas leak. See Warning statement
above
1. Improper log placement
2. Drafts or other air currents affecting
flame pattern
3. Air holes at burner inlet blocked
4. Burner flame holes blocked
www.desatech.com
21
1. Take apart gas tubing and remove foreign matter
2. Locate and correct all leaks (see Check-ing Gas Connections, page 12)
1. Properly locate logs (see Installing Logs,
page 13)
2. Eliminate source of drafts around heater
3. Clean out air holes at burner inlet. Periodically repeat as needed
4. Remove blockage or replace burner
Page 22
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
WIRING DIAGRAM
Note
: For proper operation of optional accessories, the wires from the switch to the
control must be connected exactly as shown.
AUTO
OFF
ON
SPECIFICATIONS
LFP33NRA Remote Ready
Btu (Variable)20,000/30,000
Type GasNatural Gas Only
IgnitionPiezo
Pressure Manifold3.5" W.C.
Inlet Gas Pressure (in. of water)
Maximum10.5"
Minimum*5"
Shipping Weight122 lbs.
* For input adjustment
Thermopile
SERVICE HINTS
When Gas Pressure Is Too Low
• pilot will not stay lit
• burners will have delayed ignition
• heater will not produce specified heat
When Gas Quality Is Bad
• pilot will not stay lit
• burners will produce flames and soot
• heater will backfire when lit
You may feel your gas pressure is too low or
gas quality is bad. If so, contact your local
natural gas supplier.
TECHNICAL
SERVICE
You may have further questions about installation, operation, or troubleshooting.
If so, contact DESA International’s Technical Service Department at 1-800-DESA LOG
(1-800-337-2564).
You can also visit DESA International’s
technical service web site at
www.desatech.com.
22
107063
Page 23
OWNER’S MANUAL
REPLACEMENT
PARTS
Note:
Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product.
If they can’t supply original replacement
part(s), call DESA International’s Technical Service Department at
1-800-DESA LOG (1-800-337-2564).
When calling DESA International, have
ready
• your name
• your address
• model and serial numbers of your fireplace
• how fireplace was malfunctioning
• type of gas used (propane or natural gas)
• purchase date
Usually, we will ask you to return the defec-
tive part to the factory.
PARTS NOT UNDER
WARRANTY
Contact authorized dealers of this product
or Parts Central. If they can’t supply original replacement part(s), call DESA
International’s Parts Department at 1-800972-7879 for referral information.
When calling DESA International, have
ready
• model number of your fireplace
• the replacement part number
PARTS CENTRAL
These Parts Centrals are privately owned businesses. They have agreed to support our
customer’s needs by providing original replacement parts and accessories.
Baltimore Electric
1348 Dixwell Avenue
Hamden, CT 06514-0322
1-800-397-7553
203-248-7553
Parts Department
Portable Heater Parts
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
All States
219-462-7441
1-800-362-6951
sales@portableheaterparts.com
techservice@portableheaterparts.com
FBD
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
1-800-654-8534
Fax: 1-800-846-0090
franktalk@aol.com
Master Parts Dist.
1251 Mound Ave NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-446-1446
Fax: 616-791-8270
www.nbmc.com
Washer Equipment Co.
1715 Main Street
Kansas City, MO 64108-2195
KS, MO, AR
816-842-3911
www.washerparts.com
East Coast Energy Products
707 Broadway
W. Long Branch, NJ 07764-1542
732-870-8809
1-800-755-8809
www.njplaza.com/ecep
58 Halbe Lane
Cape May Court, NJ 08210-1110
609-390-1100
Parts Department
Dayton Hardware
P.O. Box 275
North Dayton Station
Dayton, OH 45404-0275
All States
937-258-3721
OH 1-800-762-3426
Halco Enterprises
208 Carter Drive, Unit 21
West Chester, PA 19382-4500
610-430-7717
1-800-368-0803
www.halcoenterprises.com
LA Porte’s Parts & Service
2444 N. 5th Street
Hartsville, SC 29550-7704
803-332-0191
Parts Department
Cans Unlimited, Inc.
P.O. Box 645
Taylor, SC 29687-0013
All States
803-879-3009
1-800-845-5301
cuisales@aol.com
107063
23
Page 24
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
ACCESSORIES
Purchase these fireplace accessories from
your local dealer or Parts Central (see page
23). If they can not supply these accessories, call DESA International’s Sales Department at 1-800-458-2472 for referral information. You can also write to the address
listed on the back page of this manual.
LOWE’S EXCLUSIVE CABINET
MANTEL AND BASE
ACCESSORY WITH
FIREPLACE PERIMETER TRIM
GMC8CU Series - Unfinished
Birch Veneer, Ready to Stain or
Paint
GMC9CF Series - Walnut
Stained Birch Veneer
CABINET MANTEL
ACCESSORY WITH
FIREPLACE PERIMETER
BRASS TRIM
GMC11F Series - Walnut
Finished Hardwood Veneer
GMC12U Series - Unfinished
Hardwood Veneer, Ready to
Stain or Paint.
GMC13F Series - Medium
Stained Oak Veneer
Mantel features moldings, fluted sides, and
medallion.
Dimensions (H xW xD): 44" x 57 3/4" x
22 7/8"
HEARTH BASE (for Use with
Cabinet Mantel)
GC3333F Series - Walnut
Finished Hardwood Veneer
GC3334U Series - Unfinished
Hardwood Veneer
GC3335F Series - Medium
Stained Oak Veneer
The hearth base creates a handsome riser for
the fireplace .
Dimensions (H xW xD): 6 1/2" x 58" x 28 9/16"
CORNER MANTEL
ACCESSORY WITH
FIREPLACE PERIMETER
BRASS TRIM (Not Shown)
GMC36F Series - Walnut
Finished Birch Veneer
GMC37U Series - Unfinished
Birch Veneer, Ready to Stain or
Paint.
Space saving corner mantels feature moldings, fluting and medallion.
Dimensions (H xW xD): 48 3/4" x 60 7/8" x
34 3/4"
GMC10CF Series - Stained Oak
Veneer
Mantel and base feature moldings, fluted
sides, and medallion.
Mantel Dimensions (H xW xD): 44 3/4" x
53" x 20 3/4"
Base Dimensions (H xW xD): 3 3/4" x 48 1/4"
x 23 3/4"
24
107063
Page 25
OWNER’S MANUAL
ACCESSORIES
Continued
EQUIPMENT SHUTOFF
VALVE - GA5010
For all models. Equipment shutoff valve with
1/8" NPT tap. Fits 1/2" NPT pipe.
BLOWER ACCESSORY
GA3750 SERIES AND
GA3650T SERIES
Manual variable control and automatic thermostat variable control. A blower will increase air flow to maximize heat distribution.
HAND-HELD REMOTE
CONTROL - RM4
For remote control operation. Installation
and limited operation instructions included
in this manual. Extended operation instructions included with remote. Hand-held re-
mote control is available at Lowe's and is
not supplied by Comfort Glow.
HI
TEMP
MAN
AUTO
ONLO
OFF
STATUS
RECEIVER AND HAND-HELD
THERMOSTAT REMOTE
CONTROL KIT
CGHRCT SERIES
Allows the gas log heater to be operated in
a manually or thermostatically-controlled
mode. You can turn the gas log heater on and
off without ever leaving the comfort of your
easy chair.
CLEANING KIT - CCK
(Not Shown)
Your vent-free gas appliance requires regular cleaning and maintenance to prevent
performance problems. This kit gives you
the tools and instructions to make it easy to
clean all critical areas of your appliance.
DUPLEX OUTLET KIT GA3555 (Not Shown)
Use for built-in installations when hard wiring a blower.
BRASS TRIM ACCESSORY
GA7090 (Not Shown)
Optional with built-in installation. Provides a
finished appearance covering rough and/or
unfinished mantel or wall opening, edges, etc.
107063
RECEIVER AND HAND-HELD
REMOTE CONTROL KIT CGHRC SERIES
Allows the gas log heater to be turned on and
off by using a hand-held remote control.
25
Page 26
LFP33NRA
UNVENTED NATURAL GAS FIREPLACE
ILLUSTRATED
PARTS
BREAKDOWN
REMOTE READY MODEL
LFP33NRA
3
1
5
2
4
13
12
22
9
7
6
10
8
11
17
7
30
31
16
18
19
24
I
H
L
O
O
F
F
N
O
P
I
T
L
O
25
28
14
15
21
22
20
23
29
26
26
27
32
107063
Page 27
OWNER’S MANUAL
PARTS LIST
REMOTE READY MODEL
LFP33NRA
This list contains replaceable parts used in your fireplace. When ordering parts, follow the
instructions listed under Replacement Parts on page 23 of this manual.
KEY
NO.PART NUMBERDESCRIPTIONQTY.
1104937-01Middle Log (#1)1
2104938-01Back Log (#2)1
3104936-01Front Log (#3)1
4104939-01Crossover Log (#4)1
5103779-01ODS Pilot (NG)1
6098249-01ODS Nut2
7100609-01Pilot Tube (Regulator to Pilot)1
8104229-01Burner Outlet Tube1
9102843-01Burner Clip1
10099056-26Burner Orifice Injector1
11102772-01Burner2
12M11084-38Screw, #8 x .382
13104236-01CKPainted Base Assy1
14M12461-26Screw, #10 x .326
15104238-01CKFirebox Bottom1
16103284-03Wiring Harness1
17098265-02Elbow, Male1
18103782-01Valve Bracket1
19103781-01Gas Control Valve1
20098271-03Ignitor Cable1
21102445-01Piezo Ignitor1
22098304-01Phillips Pan Head Screw #1010
23099998-01Switch1
24104241-01Remote Switch Bracket1
25103587-02CKSwitch Plate1
26097809-02Male Connector1
27101628-03Flexible Connector (Hose)1
28M50104-02Bushing1
29M11084-26Screw, #10 x .384
30099918-02Pilot Regulator1
31099387-07Pilot Tube (Valve to Regulator)1
32901256-01Fitting 3/8" Flare to 1/2" NPT1
This list contains replaceable parts used in your fireplace. When ordering parts, follow the
instructions listed under Replacement Parts on page 23 of this manual.
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written
warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
COMFORT GLOW VENT-FREE NATURAL GAS FIREPLACE
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first
purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.
To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater
to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST
be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts.
Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance
with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become
damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost,
labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT;
THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE;
AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND
DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential
damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
107063 01
NOT A UPC
107063-01
Rev. B
04/00
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.