Denver TFD-2201DVBT User Manual

22″ TFT LCD TV

WITH DVB-T & DVD COMBO

TFD-2201DVBT

Instruction Manual

Dear Customers

Thanks for purchasing this TFT-LCD TV/Monitor. We strongly recommend
that you carefully read the safety and operation instructions before
operating your TV/Monitor. FOLLOW INSTRUCTIONS AND HEED ALL

WARNINGS on your TFT-LCD TV/Monitor and in this manual.

Safety information

__________________________________________________
Note:

Before connecting the AC power cord to the DC adapter outlet, make sure
that the voltage designation of the DC adapter corresponds to the local
electrical supply. If you are unsure about your power supply, please ask

the local power company.

Caution:

To avoid electric shock, never touch the inside of the LCD TV/Monitor. Only
qualified technicians should open the case of the LCD TV/Monitor.

Warning:

Do not defeat the safety purpose of grounding-type. A grounding type plug
has two blades and a third grounding pin. The third pin is provided for your
safety. If the plug does not fit, ask the electrician to replace the obsolete
outlet. Do not modify the plug!

To reduce the risk of fire or electric shock, and annoying interference, use
the recommended accessories only.

1

Precautions

________________________________________________________

Please read the below precautions carefully before operating the unit.

Power cord protection:

1. Never use your LCD TV/Monitor if the power cord has been damaged.
Do not put anything on the power cord, and keep the power cord away
from where people can easily trip over it.

2. Be sure to hold the plug , do not pull the cord when disconnecting the
LCD TV/Monitor from an electric socket.

3. Locate your LCD TV/Monitor near an easy accessible AC outlet.

4. The power cable/disconnect device shall remain easy
to operate/disconnect.

Placement:

1. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.

2. An appliance and a cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.

3. Never placing the LCD TV/Monitor in areas under direct sun-light, with
high temperature or with high humidity or high level of dust which ma y
cause damages on the internal parts of the LCD TV/Monitor.

4. Place the LCD TV/Monitor on a solid surface and treat it carefully. The
screen is made of thin glass with a plastic front surface and can be
damaged by dropping, hitting or scratching.

Non-use periods:

Unplug the LCD TV/Monitor when it is not being used for a long period.

Foreign objects:

Never insert any foreign object into the holes on the cabinet of the
TV/Monitor. Doing so may cause the danger of electric shock.

2

Keep away from water/magnetic fields:

1. Do not expose the LCD TV/Monitor to rain or use it near water source.
If the LCD TV/Monitor gets wet, unplug it and contact an authorized
dealer immediately.

2. Do not clean the front panel with Ketone-type materials, ethyl alcohol,
toluene, acid, methyl, or chloride since they may cause damage to the
panel.

3. Keep the unit away from flower vases, tubs, sinks etc. if liquids spill
into the unit, serious damage will occur.

4. Do not place magnetic objects close to the LCD TV/Monitor.

Stacking:

Opening in the LCD TV/monitor cabinet are provided for ventilation. To
prevent overheating, these openings should not be blocked or covered.
Never use the unit on a bed, sofa, rug, or other uneven surfaces. Doing s o
may block the ventilation openings in the bottom of the unit. If you place the
LCD TV/Monitor in a bookcase or some other enclosed place, please make
sure to provide adequate space for ventilation.

Servicing:

1. If the LCD TV/Monitor does not operate normally – In particular, if there
are any unusual sounds or smells coming from the unit – just unplu g it
immediately and contact an authorized dealer or service center.

2. Unplug the LCD TV/Monitor from the AC outlet before any service.

3. Make sure the service technician uses authorized replacement parts or
their equivalents. Unauthorized parts any cause fire, electrical shock,
or other hazard.

4. Following any service or repair, be sure the service technician
performs safety checks to certify that the TFT LCD TV/Monitor is in
safe operating order.

3

Unpacking

___________________________________________

Please make sure that the following items are included with your LCD
TV/Monitor. If any item is missing, please contact your dealer.

TFT LCD TV/ Monitor

Remote control

DC adapter

RCA cable

Operation manual

Power cord

4

I. View of the TV/Monitor

Front view

Back view

1. Remote sensor

2. Power button & indication light

3. DVD play/pause button

4. DVD stop playing button

5. DVD open/close button

6. CH+/Up direction button

7. CH-/Down direction button

8. VOL+/Right direction button

9. VOL-/Left direction button

10. Menu button

11. TV /AV function switch button

12. DVD disc slot in

13. DC input jack/Car cord input jack

14. HDMI jack

15. VGA jack

16. SCART jack

17. S-video jack

18. Video jack

19. Audio in (Left) jack

20. Audio in (Right) jack

21. PC audio in jack

22. Earphone

23. TVRF antenna jack

2

1

5

II. Remote control reference guide

(1) Remote control function

10
11

12
13
14
15

16
17
18
19
20

21
22
23

24

1

2

3

4

5
6
7
8

9

SUB(DVBT)

44
43

42
41

40
39

38
37

36
35

34

33

32
31

30

29
28

27

26

25

6

1. Unit STANDBY button

2. 0-9 Numerical button

3. -/-- button

4. ASPECT button to show LCD

screen display size.

5. Volume up button

6. Display channel’s information

7. Volume down button

8.

navigation button

9. ENTER button

10.

navigation button

11.

navigation button

12. Display LCD TV OSD Menu

13. Different video modes selection

14. Display INPUT source

15. DTV source decrease favorite

channel or stop DVD playing.

16. Display FAV menu in DTV mode

or play/pause DVD playing.

17. Hold on or off current page

display in teletext mode, or
advance forward to next chapter
or DVD skip forward playing.

18. Enter into teletext mode or

replay the current program from
the previous chapter or DVD skip
backward playing.

19. Change the display size in

teletext mode or DVD fast
forward playing..

20. Display the index page in teletext

mode or DVD fast rewind
playing.

21. D.MENU button

22. Display DVD title menu

23. To select DVD program playback

or display red subject of teletext
or select TV/RADIO program in
DTV mode

24. Display green subject of teletext

7

or audio function in DTV mode.

25. Disc repeat playback or display
yellow subject of teletext. or
freeze function in DTV mode.

26. Disc repeat A-B playback or
display blue subject of teletext.
or subtitle function in DTV
mode.

27. D.DISP button

28. DVD goto function.

29. To reveal or hidden the hidden
words in teletext mode or select
DVD different playback angle.

30. Sub coded page access in
teletext mode or select zoom
function of DVD playback

31. Select program’s language in
DTV mode or DVD audio
channels

32. To switch the dialogue at the
bottom of the screen during
DVD playback.

33. Display EPG DTV menu.

34. DTV source increase favorite
channel or step the speed of
DVD playing.

35. Unit sleep time selection.

36. Different sound modes
selection

37. EXIT button or DVD menu
setup

38.

navigation button

39. Select last channel

40. Select next channel

41. Select NICAM function

42. Return to the previous channel
viewed

43. MUTE button

44. Eject disc in DVD mode or
select auto adjust in PC VGA
mode.

(2) Remote control battery installation and cautions

Replace battery by following the below steps:
Requires one pair of AAA batteries.

1. Open the battery cover as shown below:

2. Install the battery into the battery tray.

3. Close the battery cover

Caution:

1. Keep the battery out of children’s reach.

2. Don’t attempt to recharge, short-circuit, disassemble, heat or throw the
batteries into the fire.

3. Always replace both batteries at the same time. Never mix new and old
batteries or batteries of a different type.

4. If you don’t intend to use the remote control for an extended period,
remove the batteries to prevent possible leakage and corrosion.

Notes:

1. Do not drop, apply shock or step on the remote control.

2. Do not spill water on the remote control.

3. Do not use the remote control for other equipments at the same time

4. If the TV does not operate even when operating the remote control
from a close range, you need to replace the batteries.
Refer to the label on the back of the remote control for directions for
replacing batteries.

8

III. Installation and connection

Connect the LCD TV/monitor

1. Connect the TVRF source with the antenna port. TVRF signal

including: Receiving antenna /satellite TV/CATV net. You can use 75
Ω coaxial cable to connect the outdoor antenna.

Outdoor Antenna Connection:

Use 75Ωcoaxial cable plug or 300-75Ωimpeda nce converter to plug
in antenna input terminal on the rear of the cabinet.

VHF antenna

Mixer

Antenna in jack

UHF antenna

75ΩCo-axis cable

9

Input terminal of

antenna

Co-axis antenna
plug

-

2. Connect the audio sources (Including DVD, VCDR, CAMCORDER

and PC) to the proper AUDIO input jacks ‘L’ and ‘R’.

3. Connect the video source to the VIDEO jack by RCA cable.

4. If the video source has a SCART output jack, you can connect the

signal to the monitor by the SCART cable.

5. Connect the video source to the S-VIDEO input jack of the monitor by

the S-video cable (Pretending that the video source has S-video
output jack).

6. Insert the AC power to the DC adaptor, then connect 12V input jack

from the monitor to it’s DC output jack.

7. W hen using the LCD as a computer screen, connect the PC to the

VGA jack from the monitor by the relevant cable.

8. If the video source has a HDMI output jack, you can connect the

signal to the monitor by the HDMI cable.

IV. TV/Monitor screen operation

(1) Basic operation

1. Press the POWER button on the unit or the STANDBY button on the
remote control to switch on the power, the indication light will be in blue
color . Press the POWER or STANDBY button again to switch off the
power, and the light will be in red color.

2. T he Picture setup, Sound setup, Previous channel can be memorized
before you switch off the TV/Monitor. The TV/Monitor will re-start under
the previous state when you switch on it again.

3. Press the VOL - or VOL + button to adjust the volume output. Press
the VOL - button repeatedly to decrease the volume; press the VOL +
button repeatedly to increase the volume from 0 to 100.

(2) View the TV plays.

1. Press the INPUT button on the remote control to select the TV function
mode. Channel ‘1’ will appear on the right top corner after channel
searching is completed Press the CH- or CH+ button to select the
previous or next channels; or press the 0-9 buttons to enter a channel
number directly, or press the -/-- button until the screen display ‘-’ or ‘--’,

10

then use the 0-9 numerical buttons to enter a channel number from 1
to 99.

2. Press the button on the remote control to select from the present
channel and the previous channel.

3. Press the PMODE button repeatedly to cycle through the available
video picture modes from the below 6 types

Standard Personal Movie Sport

4. Press the SMODE button to repeatedly to cycle through the available
sound modes from the below 4 types

Music Theatre Personal Voice

5. Press the MUTE button to cut off the sound output, press this button
again to resume sound output..

6. Press the DISPLAY button to display the preset TV channel play
information

7. Press the ASPECT button to repeatedly to cycle through the available
LCD screen display size from the below 8 types

FullScreen

NOTE:
This available aspect size may be different in difference input source.

8. Press the SLEEP button to repeated ly to cycle through the available
unit sleep time from the below 9 types

0Min.

Subtitle 16:9 4:3 14:9

15Min

120Min. 105Min.

ZOOM1

30Min.

11

Mild Game

ZOOM2 Auto

60Min45Min

75Min90Min

(3) View the AV signal sources (DVD/VCR/CAMCORDER)

Press the INPUT button on the remote control, there will be a menu
displayed on the screen as followed:
Select the suitable input to pickup the AV signal.
Press or button to select source, then press

button to confirm your selection.

Note:
When no disc in the DVD mechanism, if you
want to change the mode from DVD to
TV, please wait several seconds until the
LCD screen shows "No Disc".

SOURCE MENU

TV
SCART
CVBS
S-VIDEO
VGA
HDMI
DVD
DTV

(4) View the TELETEXT program

(Optional. If TV has this function.)

1. Press INPUT button to select the TV mode. Then press the CH- or
CH+ button on the remote control to select TV channel in order to pick

up the picture signal of TELETEXT. (Firstly you must view the 3
of chapter V to complete the TV channel searching).

2. Press the CH- or CH+ button to select the previous page or the next
page; use the 0-9 numerical buttons and the -/- - button to enter into a
numerous page.

3. Refer to the chapter of ‘Remote control reference guide’ to grasp other
functions of the TELETEXT buttons.

TEXT

Press TEXT button to enter into T EXT mode. Press this button again to
return to the channel you are watching.

HOLD

Press this button to stop the move to the next page, and the hold symbol
will appear in the top left hand corner of the screen. Press this button again
to cancel operation.

INDEX

Press this button to go to the INDEX page.

Enter into the

picture showing

12

Exit

rd

part

SIZE

Press this button to enlarge the text shown on the teletext screen, and one
half of page could be shown.
Press this button again to view the second half of this page.
Press this button third time to normal size text page view.

REVEAL

Press this button to reveal the cancelled information.
Press this button again to cancel the information.

SUBPAGE

Press this button to select sub page, and the sub page symbol will appear
in the left top hand corner of the screen. Enter the number of sub page and
use numeric buttons in the format 0001for sub page 1.The teletext will
search for the sub page

RED/GREEN/YELLOW/BLUE COLOR BUTTONS

Press these 4 color buttons to access directly to corresponding color page
displayed at the lower parts of teletext screen.

(5) PC screen

Press the INPUT button to select the VGA input (TV into PC) mode. A ‘VGA ’
mark will appear on the right of the top corner of the monitor. The unit has a
VGA jack for a normal computer . Connect the monitor with a PC by this jack
and the unit can be used as the monitor for the PC.

V. Menu setting and adjustment

Note:
In this manual, the OSD Menu maybe changed and different from y our
real TV’s screen shown without further notice. Because this manual is
just a sample to help you how to operate TV menu setting.

1. PICTURE SETTING

Press the LCD MENU button on the remote control firstly, then press or

button to select PICTURE SETTINGS MENU dis played on the screen

as below:

13