DentalEZ everLight EVLCE Installation, Operation & Care Manual

Download

Track, Ceiling, Wall & Cabinet Mount

Installation, Operation & Care Manual

DentalEZ MAKES YOUR PRACTICE PERFECT

Ta b l e o f C o n t e n t s

Section I Introduction

Specifications ......................................................................................................................... 2

Classifications ........................................................................................................................2

Dimensions ........................................................................................................................ 3-4

Light Head Range of Motion .............................................................................................. 5

Packaging ................................................................................................................................ 5

Section II Installation

Tr ac k M ou n t A ss e mb l y..................................................................................................6-10

Ceiling Mount Assembly............................................................................................. 11-14

Wall Mount Assembly................................................................................................. 15-16

Cabinet Mount Assembly...........................................................................................17-18

Section III Operation

Light Switch ........................................................................................................................ 19

To u c h p a d s ........................................................................................................................... 19

Positioning Light ................................................................................................................ 20

Eliminating Adjustable Arm Drift (Wall Mount) .......................................................... 21

Section IV Care

Cleaning & Disinfecting .................................................................................................... 22

Section V User Service Information

Tro u bl es ho ot i ng ................................................................................................................ 23

Service Instruction ............................................................................................................ 23

Section VI Parts List/Diagrams

Light Arm ............................................................................................................................. 24

Light Head ........................................................................................................................... 24

Drop Post ............................................................................................................................ 24

Product Support Services ..................................................................................... 25

Wiring Schematic......................................................................................................... 26

EMC Information .................................................................................................... 27-28

Mounting Template (Ceiling/Wall Mount)

Installation, Operation and Care Manual

EverLight® 1

Section I Introduction

EverLight

This manual contains installation, operation and care instructions and user service information for the

EverLight® LED light.

The EverLight is designed to provide trouble-free service when installed, operated and maintained according to the procedures set forth in this manual.

To ens ure correct track, ceiling, wa ll or ca binet mounting installation, carefully read all the instructions contained in this manual paying close attention to all notes, notices, cautions and warnings.

After the EverLight is installed, please review the operation procedures and care guidelines with the doctor's staff. Then!"#$%#!&'()!*$+,$"!(+!&'#

-./&.01)!.22(/# for future reference.

Specifications

3.4#0!5,66"78 Primary: 100-240 V AC 50/60 Hz. Secondary: 12V DC

96#0$&(+:!;*6#0$:#8! .4 max. - .16 min. Amp <./$"!=#+:&'8 27"

C Type of protect ion against electri c shock: Cl ass 1

Equipment

C Degree of protection against the ingress of water:

Ordinary

C Equipment not suitable for use in the presence of

a flammable anesthetic mixture with air or with oxygen or nitrous oxide.

C Mode of operation: Continuous C Environmental conditions recommended ranges for:

Transport and Storage:

D Temperature range of - 10º C to + 70º C D Relative humidity range of 10% to 100% D Atmospheric pressure range of 500 to 1060 hPa

Normal Use:

D Temperature range of + 10º C to + 40º C D Relative humidity range of 30% to 75% D Atmospheric pressure range of 700 to 1060 hPa

Explanation of Symbols used on Equipment:

=Attention, Consult Accompanying Documents

>.".0!?#*6#0$&,0#8 High: 5300° Kelvin

(Color Matching)

Medium: 4300° Kelvin

(Operative Setting)

Low: 3200° Kelvin

(Composite Setting)

=(:'&!@+&#+)(&78 High: 2300 Footcandles

(25,000 Lux)

Medium: 1375 Footcandles

(15,000 Lux)

Low: 725 Footcandles

(8,000 Lux)

=(:'&!3$&�+8!!6-1/2" x 3-1/2" A+(&!B#(:'&8 Track Mount: 87 lbs.

Ceiling Mount: 41 lbs

Wall Mo un t: 59 lbs.

abinet Mount: 51 lbs.

Classifications

Class 1, Medical Equipment for Ordinary Use with Respect to Electric Shock, Fire and Mechanical Hazards

53HN

Only in Accordance with UL 60601-1, IEC 60601-1, CAN/CSA 22.2 No. 601.1

=Voltage, AC

=Voltage, DC

=Caution. Electrical Shock Hazard. Refer Servicing

to Qualified Personnel

=European Certification - If applicable, see

nameplate.

— SPECIAL NOTICES —

In accordance with Part 15 of FCC rules, this

Medical electircal equipment needs special

Mobile radio frequency (RF) communications

Light Arm Assembly

equipment was tested and complies with Class A digital device limits. These limits are designed to give equipment reasonable protection against detrimental interference when operated in a commercial environment.

precautions regarding electromagnetic compatibility (EMC) and needs to be installed according to EMC information. (See EMC

Information Pgs. 27 and 28.)

equipment can effect medical electrical equipment.

2 Installation, Operation and Care Manual

Section I Introduction

Dimensions

24"

1.61"

1.25"

15"

17"

14.375"

3.5"

Tr a ck M o u n t

1.375"

24"

7.25"

14.375"

15"

17"

31.875"

Ceiling Mount

EverLight® 3

Section I Introduction

24"

EverLight

14.375"

15"

17"

4.5"

Wall/Cabinet Mount

1.375"

56"

4 Installation, Operation and Care Manual

Section I Introduction

Light Head Range of Motion

145º

150º

180º

Packaging

Verify the EverLigh t compone nts packagi ng conten ts against the appropriate mounting configuration's packing list.

!"#$: Be aware that some sections of the carton

may be packed as fillers and might be empty (even if optional components are ordered).

— NOTICE —

For any questions about an order, please

contact a DentalEZ Equipment customer

service representative at %&'((&)#$&*!+"

,%&'((&-'-&.(-(/.

Carefully unpack the light. Inspect all of the items received to assure there has been no shipping damage.

*0 123435617812789:;6<62=19:>?39?1?@6193<<76< 7446273?6ABC1#@6>1<6D:<?13>2107A61?@613DD<:D<7& 3?619A37481E7?@1?@6193<<76<1E7?@7>1F.1@:G<8130?6< 26A7;6<B. (See Product Support Services, Page 25.)

— IMPORTANT NOTE —

All parts supplied are vital for proper installation.

):1>:? discard any hardware or components

until installation is checked and complete.

EverLight® 5

Section II Installation

EverLight

Tr ack M oun t A s se m bly

To o l s R e q u i r e d

H Phillips-head Screwdriver H Torpedo Level H Set of Allen Wrenches H Power Drill H Stripping/Crimping tool H Drill Bits

H Pipe Cutter/Hacksaw H Tape Measure

H Lubricant: Silicon/Grease Product

Track Assembly Installation

— NOTICE —

Because of the size and weight of the track

mount assembly, two people are required

for installation.

!"#$I1The ceiling structure

supporting 200 pounds. Additional bracing to the ceiling structure may need to be provided.

!"#$I1The mounting lag bolts

minimum of 2-1/2" of solid wood.

4G8?

be capable of

4G8?

go into a

%.After determining the location of the track

light (see illustration below), arrange for the hole for the power cord to be above the head of the chair.

F.Drill four 5/16" mounting holes and a 1-1/2"

power supply hole.

— NOTICE —

A full-size track mount template is available.

Order PN:1F(JJ&KLK.

-. Remove the track light assembly from the packaging and lay it flat with mounting side down on the floor or sturdy table.

1..Using a Phillips-head screwdriver, remove and retain the four screws that hold the side covers to each end of the wood mounting pallet.

Screw

Side

Cover

Power Connection

This End

Floor

Suggested Track Mount Location

End of Track

77"

53"

71"

Extended-length

post assembly

required for

ceiling heights:

8' 1" to 10'

8' 0" Min.

6 Installation, Operation and Care Manual

Section II Installation

!"#$I1Refer to the exploded illustration below

during track light installation.

L.Loosen, but do not remove, two Phillips-

head screws from one end cap of the track mount assembly.

(C After loosening the end cap (do not remove

end cap), take off the side covers and set

them aside.

Side Covers

Power Supply

Housing Cover

Side

Cover

Support Hub

End Cap

Phillips-head

Screws

Wood

Mounting

Pallet

End Cap

Tro l ley

Trolley Cover

Cut End

Machined End

Stop Collar

Drop Post

Swivel Key

Swivel Sleeve

Rigid Arm

Spindle

Light Arm Assembly

EverLight® 7

Section II Installation

EverLight

J.Remove the four screws from the power

supply housing cover, then take off the cover and set the screws and cover aside.

Power Supply

Housing Cover

Screws

'.Remove the template from the ceiling.

M.Mount the track assembly to the ceiling using

the four 1/4 x 3" lag bolts supplied. (Only if needed, slide the supplied spacers over the four lag bolts before mounting the track.)

Power Supply Wiring

%.Make sure the appropriate electrical line

(100-240 VAC, 50/60 Hz) is properly supplied to the power supply housing.

— NOTICE —

All wiring 4G8? be in accordance with local

electrical codes.

!"#$I1If possible, install a wall switch in the

power source to the track light. This can be turned off to eliminate wear of the power supply and protect against electrical surges.

— WARNING —

Before proceeding, verify the power at the

main circuit is "++.

1/4 x 3"

Lag Bolt

If trolley removal is necessary:

%.Remove the end cover and the stops on the end

of the track opposite the power supply housing.

F.While supporting the trolley, roll it off the track

and remove the strain relief from the bracket.

-.To reassemble, reverse the procedure making sure the rounded wheel goes into the grooved side of the track.

!"#$I1There is a hole in the wood pallet and the

power supply housing for routing the electrical supply.

F.Pull the power supply cord through the

ceiling and hole in the wood mounting pallet.

Power Supply

Housing

-.Connect the supply to the black white and green leads in the power supply housing.

Woo d Mo unti ng

Pallet

8 Installation, Operation and Care Manual

!"#$I1When connecting to a 115V power source,

connect the wires accordingly: ground to green, neutral to white and black to hot.

Section II Installation

4.Tuck the wires in neatly and replace the power supply housing cover using the retaining screws previously removed.

5.Replace the side covers using the four Phillips-head screws previously removed.

6.Tighten the two Phillips-head screws on the loosened end cap.

Drop Post Installation

NOTE: The track light is designed to accommodate

up to a 10' ceiling. The drop post

length

chart below for the correct post length for various ceiling heights.

for the appropriate ceiling height. Refer to the

Ceiling Height 8' 8'-6" 9' 9'-6" 10'

Post Len g th 12" 18" 24" 30" 36"

must be cut to

NOTE: This hole is for the 5/16" bolt that secures

the drop post to the support hub.

4.Route the pigtail from the trolley through the drop post

5.Insert the drop post into the support hub and tighten the 5/16" bolt through the drop post and let the post rest on the bolt.

— CAUTION —

Failure to install the bolt as described may

allow the light to fall.

6.Tighten the eight set screws in the support

hub and make sure the post is plumb from front to back and side to side.

7.Slide the cover and cover support up the drop post and tighten the set screw in the cover support to prevent the cover from falling.

1.Remove the three screws from the lower end of the drop post assembly. Then take out the swivel sleeve and swivel key.

— CAUTION —

Do not cut the post at the end containing

the three machined screw holes.

2.Measure the post from the end containing the three machined screw holes and cut to length according to the chart above.

NOTE: Remove any sharp edges.

— CAUTION —

Do not drill into the end of the post

containing the three machined screw holes.

3.At a distance of 1-5/8" from the cut end of

the post, drill an 11/32" (.343) diameter hole on the center line of the post.

8. Lightly lubricate the inside of the swivel sleeve.

NOTE: The swivel sleeve and swivel key must face

towards the toeboard of the chair to prevent the light arm from rotating a full 360°. (See illustration below.)

Button-head Screws

Swivel

Key

Swivel Sleeve

9.Correctly orient and place the swivel sleeve on the rigid arm spindle and insert the swivel key in the slot to secure the sleeve and spindle.

10.After determining the proper wire length, push any excess wiring into the post and connect the harnesses.

EverLight® 9

Section II Installation

Drop Post

Spindle with

Swivel Sleeve

and Swivel Key

11.Insert the spindle with the swivel and swivel

key into the drop post with the key facing towards the foot of the chair.

12.Align the three holes of the swivel sleeve and

the drop post and secure with three button-head screws.

EverLight

Flex Arm Height Adjustment

1.An adjustment can be made to the flex arm

travel in the event the flex arm contacts the track or the ceiling.

2.To access the adjustable stop, remove the

four screws that hold the arm cover.

3.Remove one of the arm end caps. These have

been attached with a small amount of glue and require care in removing.

4.Slide the arm cover toward one end of the

arm to expose the compression spring retaining mechanism.

5.The adjustable stop is located on the spring

rod directly behind the friction block and between the spring stopper.

Stop

Secure with

three button-

head screws

13.Check the level of the post and readjust if

necessary.

14.See "Testing" section on this page.

6.Loosen the two retaining set screws in the

top of the block and position the stop to limit the vertical travel of the arm to the desired position. Then tighten the set screws.

7. Slide the arm cover back in position and

attach using four retaining screws.

8.Replace the end cap using a small amount of

adhesive.

Te s t i n g

1.Before proceeding, verify that the power to the main circuit breaker panel is ON.

2 Move the toggle switch, located immediately

behind the light head, UP to turn the light ON.

10 Installation, Operation and Care Manual

Section II Installation

Ceiling Mount Assembly

To o l s R e q u i r e d

H Phillips-head Screwdriver H Bubble Level

H Set of Allen Wrenches H Power Drill & Bits

H Stripping/Crimping tool H Hammer

H Pipe Cutter/Hacksaw H Tape Measure

H Lubricant: Silicon/Grease Product

— NOTICE —

For any questions about an order, please contact

a DentalEZ Equipment customer service repre-

sentative at %&'((&)#$&*!+".

Suggested Ceiling Mount Location

25-1/2"

Framing & Mounting

— IMPORTANT NOTE —

Before any framing is done, 3AE3B8 obtain the

doctor's approval.

%.Adjust the chair back to its full1)"N! posi-

tion and the seat to normal operating position.

F.For a suggested ceiling mount location, refer

to the illustration below.

!"#$I1Frame locations may be varied to suit

individual preferences. But, be aware of the following framing considerations.

H Check ceiling structure and assure it will

support a minimum of 200 pounds.

25-1/2"

Left-Hand Operation

Right-Hand Operation

EverLight® 11

Section II Installation

EverLight

H Ensure no lateral movement of the light

column is possible.

H Check for an electrical circuit near the

support area of the light.

-.Using the full-size ceiling mount template in the back of this manual, drill three holes for the ceiling mount plate.

Ceiling Joists

Nails or

Lag Screws

..Attach the ceiling mount plate to the framing

joist using three bolts that are 3/8" diameter or larger and appropriate for the framing construction. (The bolts are not supplied.)

!"#$I1For suspended ceiling installation, spacers are

provided to use between the frame and the ceiling mount plate.

Power Supply Wiring

%.Make sure the appropriate electrical line

(100-240 VAC, 50/60 Hz) is properly supplied to the junction box.

F.Remove the junction box cover.

— NOTICE —

All wiring 4G8? be in accordance with local

electrical codes.

— WARNING —

Before proceeding, verify the power at the

main circuit breaker panel is "++.

-.Route the power supply wiring through the hole in the ceiling mount plate.

Wiring

Hole

Power Supply

Mounting Light Support Above

Suspended Ceiling

Steel Bar

Framing

Mounting Light Support At

Suspended Ceiling Level

Steel Bar

Joist

Framing & Cross

Brace

Joist

Junction

Box

..Secure the power supply wiring to the

junction box with strain relief according to local electrical codes.

Power Supply

Ground

L.Secure the incoming ground wire to the

junction box ground screw using a ring terminal from the bag of supplies.

Ceiling

Mount Plate

Junction Box

Ground

Screw

12 Installation, Operation and Care Manual

Section II Installation

Drop Post Installation

!"#$I1The ceiling light is designed to accommo-

up to an 10' ceiling. The drop post

date

9G?1?:1A6>5?@

Refer to the chart below for the correct post length for various ceiling heights.

%.Remove the three screws from the lower end

of the drop post assembly. Then take out the swivel sleeve and swivel key.

for the appropriate ceiling height.

CEILING DROP POST HEIGHT LENGTH

10' 36" 9' 6" 32" 9' 26" 8' 6" 20"

8' 14"

— CAUTION —

):1>:?19G? the drop post at the machined end

that contains the swivel sleeve screws.

F.Measure the post from the end containing

the three machined screw holes and cut to length according to the chart above.

!"#$I1Remove any sharp edges.

4G8?1O6

L.Insert the cut end of the drop post into the

support hub and tighten the 5/16" bolt through the drop post and let the post rest on the bolt.

— CAUTION —

+37AG<61?:17>8?3AA1?@61O:A?13812689<7O62143B

3AA:E1?@61A75@?1?:103AAC

Ceiling Mount Plate

Ceiling Mount Collar

Drop Post

Swivel Key

Swivel Sleeve

Ceiling Mount Cover

Ceiling Stop Collar

Cut End

Machined

End

— CAUTION —

):1>:?12<7AA into the machined end of the

tube that contains the swivel sleeve screws.

-.At a distance of 1-3/4" from the cut end of the post, drill an 11/32" (.343) diameter hole on the center line of the post.

!"#$I1This hole is for the 5/16" bolt that secures

the drop post to the support hub.

..Route the light cord from the power supply

through the cut end of the drop post . Then pull the cord through the machined end.

Light Arm

(.Using the bubble level make sure the post is

plumb from front to back and side to side. If

needed, adjust the eight set screws in the ceiling mount collar.

— CAUTION —

All 8 set screws 4G8?1O61?75@? to prevent the

light from falling!

J.Tighten the eight set screws in the ceiling

mount collar.

EverLight® 13

Section II Installation

EverLight

8. Slide the cover and cover support up the drop

post and tighten the set screw in the cover support to prevent the cover from falling.

9.Lightly lubricate the inside of the swivel sleeve.

NOTE: The swivel sleeve and swivel key must face

towards the toeboard of the chair to prevent the light arm from rotating a full 360°. (See illustration below.)

Button-head Screws

Swivel

Key

Swivel Sleeve

10.Correctly orient and place the swivel sleeve on

the rigid arm spindle and insert the swivel key in the slot to secure the sleeve and spindle.

Flex Arm Height Adjustment

An adjustment can be made to the flex arm to limit the vertical travel of the arm.

NOTE: If flex arm height adjustment is needed for

the ceiling mount, refer to the adjustment instructions for the track light found on Page 10.

Te s t i n g

1.Before proceeding, verify that the power to the main circuit breaker panel is ON.

2 Move the toggle switch, immediately behind

the light head, to the left and turn the light ON.

11.Connect the wiring harness from the rigid arm

to the light cord harness in the drop post.

12.Insert the spindle with the swivel and swivel

key into the drop post with the key facing towards the foot of the chair.

13.Align the three holes of the swivel sleeve and

the drop post and secure with three buttonhead screws.

14.Check the level of the post and readjust if

necessary.

15.Pull the excess cord through the junction box

and secure with strain relief bushing to the junction box.

16.After the wiring connections are complete,

replace the junction box cover.

17.See "Testing" section on this page.

14 Installation, Operation and Care Manual

Section II Installation

Wall Mount Assembly

To o l s R e q u i r e d

H Power Drill & Bits H Slotted Screwdriver H Phillips-head Screwdriver H Wire Crimping Tool H Tape Measure H Wire Stripper H Set of Allen Wrenches H Lubricant: Silicon/Grease Product

Wall Mount Positioning

*PQ"R#S!#1!"#$I1Check wall structure and

assure it will support a minimum of 200 pounds.

%.Place the chair back in its full )"N! position

and the seat in the normal operating position.

F. For a suggested wall mount location, refer to

the illustration below and follow this guide:

3.First identify the center point of the long arm rotation. This point should align with

the chair's center line and off-set 25-1/4" from the front edge of the chair's base plate in the direction of the headrest.

O.From this point, swing a 60" radius arc,

representing the long arm rotation, until an intersection with the wall is found.

Wall Mount Installation

%.After determining the proper position of the

wall mount, use the wall mount template in the back of this manual to align mounting holes on two wall studs.

F.Depending on the size of wall fastener

chosen, drill four mounting holes into the wall studs. Then drill a 1-1/2" center hole for the incoming power source.

!"#$I1Make sure the required power supply wiring

runs from inside the wall to the proper location.

Mounting

Bracket

Mounting

Bracket

Right-hand

Operation

Left-hand Operation

Suggested Wall Mount Location

WALL

R60"

Optional

Right-hand

Position

25.25"

WALL

Optional

Left-hand

Position

WALL

63"

FLOOR

EverLight® 15

Section II Installation

EverLight

— NOTICE —

All wiring 4G8? be in accordance with local

electrical codes.

Wall Mount

Cover

Mounting Holes

-.On the wall mount, remove and retain the four screws that secure the cover. Then take off the cover.

To p H o l e f o r

Light Arm

Screws

Nut

Black

Wire

Harness

From Light

Mounting

Bracket

Power

Supply

Harness

White

Wire

Green/Yellow

Wire

%K.Connect the white wire from the power

supply to the white wire.

%%.Insert the harness from the light into the hole

provided in the mounting bracket and attach the nut.

%F.Connect the power supply harness to the

harness from the light.

— WARNING —

Before proceeding, verify the power at the main

circuit breaker panel is "++.

..Feed the incoming power supply cord

through the center hole of the wall mount.

L.Secure the wall mount to the wall using the

four chosen fasteners.

(.Place a small amount of lubricant on the

light arm pivot pin.

J.Insert the light arm assembly, light cord first,

into the top hole of the wall mount.

'.Connect the ground wire from the power

supply to the green/yellow wire.

M.Connect the black wire from the power

supply to the black wire.

%-.After connecting the power leads, replace the

cover on the wall mount making sure no wires interfere with the closing of the cover.

%..Secure the cover to the wall mount using the

four screws previously removed.

Te s t i n g

%.Before proceeding, make sure the power at

the main circuit breaker panel is1"!.

F.Move the toggle switch, immediately behind

the light head, to the "! (up) position..

16 Installation, Operation and Care Manual

Cabinet Mount Assembly

To o l s R e q u i r e d

H Power Drill & Bits

H Slotted Screwdriver

H Phillips-head Screwdriver

H Wire Crimping Tool

Cabinet Mount Installation

Before proceeding with the cabinet mount assembly installation, the following important information regarding placement PTU# be taken into consideration.

It is imperative that the light assembly's upper primary arm is:

H mounted parallel with the ceiling,

H Tape Measure

H Wire Stripper

H Set of Allen Wrenches

H Magnetic Level

H Lubricant: Silicon/Grease Product

Power Supply Wiring

Make sure the required power supply wiring is available in the sub-base of the cabinet.

Suggested Cabinet

Mount Location

Ceiling Line

1.5"

H situated at least 1-1/2" above an X-ray arm's

highest folded position, and

H >:? in contact with or interferes with any

obstruction in the ceiling, especially sprinkler heads, smoke alarms, etc.!

The illustration below gives the suggested mounting location for the DentalEZ cabinet mount assembly and the HDX Intraoral X-ray.

!"#$I1The cabinet assembly will accommodate

either one-light or two-light assemblies.

Typical Sprinkler Head

Typical Clearance

96"

Typical

Clearance

for X-ray

Arm

25"

Adjustable

Height Post

EverLight® 17

EverLight

%.Secure the vertical mounting post(s) to the

metal frame inside the cabinet assembly using the metal post support brackets supplied.

(Refer to the illustration below.)

!"#$I1 The location of the metal angle

brackets at the lower end of the vertical mounting post(s) determines the height of the light assembly.

F.Using the supplied 1/4" lag bolts, attach the

metal angle brackets to the plywood center panel.

Upper Primary

Arm

Metal Post

Support Bracket

!"#$I1The metal post support brackets are

designed to facilitate perpendicular and parallel adjustments.

-.Using a magnetic level, ensure the light post is plumb.

..Apply a thin coating of lubricant to the

bearing surfaces.

L.To achieve anti-rotation of the vertical

mounting posts, tighten the set screws in the post support brackets.

(. Route the light assembly electrical power

cord through the metal post support brackets and cabinet metal frame to the metal subbase.

J.Insert the light arm in the bushing.

'.Connect the cord to the power supply. Then

plug the power supply into an electrical receptacle.

Plywood

Center

Panel

Ver tica l

Mounting Post

Metal Angle

Bracket

Electrical Power

Cord

Cabinet Metal

Frame

M. V6<7 0B 1? @3 ?1 ?@ 61 D:E6 <1 ?: 1?@6 143 7> 197 <9 G7?

O<63W6<1D3>6A1781"!C Then test the light

switch as described in Section III Operation (Page 19).

End View

18 Installation, Operation and Care Manual

Section III Operation

The EverLight dental light is designed to provide illumination of the oral cavity for use by dental professionals in the dental operatory.

Light Switch

The light ON/OFF paddle is located on the elbow section of the light arm assembly..

➜

OFF

Light

Paddle

Procedural Settings

! A - Sun - Color Matching - 5300° Kelvin

! B - Sun/Bulb - Operative Setting - 4300° Kelvin

! C - Bulb - Composite Setting - 3200° Kelvin

Sun - 5300° Kelvin

(Color Matching)

Sun/Bulb - 4300° Kelvin

(Operative Setting)

Bulb - 3200° Kelvin

(Composite Setting)

Intensity Settings

! 1 - Low - 8,000 Lux

! Flip the paddle to the UP to turn the light ON.

! Flip the paddle DOWN to shut the light OFF.

To u c h p a d s

Designed with three procedural and three intensity settings EverLight offers a total of nine settings to assure the correct light in every procedure.

Procedural

Settings

Intensity

Settings

! 2 - Medium - 15,000 Lux

! 3 - High - 25,000 Lux

Low

(8,000 Lux)

High

(25,000 Lux)

Medium

(15,000 Lux)

EverLight® 19

Section III Operation

Positioning Light

Using the handles on either side of the LED head, position the light to illuminate the oral cavity. (See

Light Head Range Of Motion, Page 5.)

Handles

EverLight

— HELPFUL NOTE —

To take full advant ag e o f the Ever Ligh t's

intensity and color correction, position

the light between FKX and .LX away from

the oral cavity.

20 Installation, Operation and Care Manual

Section III Operation

Eliminating Adjustable Arm Drift

The E3AA14:G>?Y8 adjustable arm is factory-adjusted to counter-balance the weight of the light head. If it becomes necessary to adjust the mechanism because of added weight, such as a mirror, perform the following steps:

To o l s R e q u i r e d

H 5/64 Allen wrench H 9/64 Allen wrench H Large Flat-head (slotted) Screwdriver

%.Using a 5/64 Allen wrench, loosen the set

screw under the cap at the end of the adjustable arm nearest the light head.

Adjustable

End Cap

Set

Screw

Arm

-. Insert a 9/64 Allen wrench into the two small holes in the side of the adjustable arm and completely loosen the friction block.

9/64 Allen

Wrench

Friction Block

Adjustable

Arm

Tw o

Small

Holes

..Insert a large flat-head screwdriver into the

large slot in the side of the adjustable arm and tighten the slotted nut.

Large

Slot

Adjustable Arm

F. Using a 5/64 Allen wrench, remove the four

Allen-head screws from the underside of the adjustable arm (two on each end). Then slide off the top cover along with the end cap.

5/64 Allen-head Screws (2)

Adjustable Arm

To p C o v e r

5/64 Allen-head

Screws (2)

End Cap

Slotted

Nut

Large Flat-head

Screwdriver

L.Adjust the friction block to provide one to

two pounds maximum of break-away force.

(.Replace the adjustable arm cover and secure

using the four 5/64 Allen-head screws previously removed.

J.Replace the end cap and tighten the set screw

using a 5/64 Allen wrench.

EverLight® 21

Section IV Care

Cleaning & Disinfecting

— CAUTION —

Avoid spraying anything directly on the light.

Spray cloth first, then wipe.

%.To clean all surfaces, use a typical

SZ["\"Z&+R$$, commercial cleaner or a

solution of mild liquid detergent and water.

F.After washing, a disinfectant may be used

following the manufacturer's instructions.

!"#$I Daily cleaning with soap and water or a

neutralizer for iodophors may reduce discoloration.

— CAUTION —

All surface disinfectants cause varying degrees

of discoloration to light-colored surfaces.

EverLight

-.The following disinfectants are acceptable to use:

• Caviwipes

• Banicide

• Coecide

22 Installation, Operation and Care Manual

Section V User Service Information

Tr ou b l e s h oo t i n g

The EverLight is designed to provide trouble-free service when installed, operated and maintained according to the procedures set forth in this manual. Under normal use, there is no routine user maintenance required.

— WARNING —

Exercise extreme caution when trouble-

shooting the electrical components of the

EverLight. When electrical power is re-

quired, safety precautions 4G8?1be observed.

The chart below should be used when troubleshooting EverLight problems.

If these suggested troubleshooting procedures do not resolve the problem, see the service instruction that follows.

Service Instruction

If the area of concern is not addressed in this manual, contact your local DentalEZ full-service dealership. (See Product Support Services, Page 25.)

Please have the following product information available:

H Model Name

H Model Number

H Serial Number

H Installation Date

H Dealer

Light Arm

Assembly

Model/Serial

Number

Plate

— NOTICE —

For convenient referencing, a color-coded wiring

schematic is located at the end of this manual.

Symptom Possible Cause(s) Solution

No light Master/light switch is in "++ position Turn "! master/light switch.

No power Check circuit breaker.

Power supply failure Replace power supply.

Broken arm wire harness Check arm wire harness for

continuity.

Faulty switch Replace switch.

Low light intensity Intensity set on low Set intensity to high.

Plastic light shield dirty Clean light shield.

Light arm drifts vertically Counterbalance out of adjustment Adjust arm drift. (See Page 21.)

Light arm drifts horizontally Light post not level Level light post.

EverLight® 23

Section VI Parts List/Diagrams

(Wall light arm assembly shown)

Light Arm

#ema N t i K / t r a P#tiK/traP

1paCd nEm r A118 - 1083

2paCm r Ad i g i R418 - 1083

3gnihsuBtsoP848 - 1083

EverLight

Light Head

#ema N t i K / t r a P#tiK/traP

4tooB&r e veLhc t i wS353 - 2083

5hct iw Sf fO/nO153 - 2083

6lor tnoCthg i LDELediSthg iR923 - 2083

7lor tnoCthg i LDELediSt feL823 - 2083

8laceDl o r t noCr o l oC733 - 2083

9laceDl o r t noCy t i sne t n I633 - 2083

01slaceD/wt iK gnisuoHlor tnoCthgiL833 - 2083

11teSr e v oCr a e l Ct n o r F133 - 2083

tiKelb aCn obbiR233 - 2083

tiKylp p uSrewoP433 - 2083

EC , t i Ky l p p u S r e wo P253 - 2083

(Drop Post for

Ceiling and Track

mount only)

24 Installation, Operation and Care Manual

#ema N t i K / t r a P#tiK/traP

21tsoPpo rD )gni l ieC&kcarT( 911 - 6852

Drop Post

Product Support Services

DentalEZ Group

DentalEZ Equipment Division

EverLight

DentalEZ Group and its employees are proud of the products we provide to the dental community. We stand behind these products with a warranty against defects in material and workmanship as provided below.

In the event that you experience difficulty with the application or operation of any of our products, please contact our Technical Service Department at our expense at 1-866-DTE-INFO (1-866-383-4636).

If we cannot resolve the issue by telephone, we will arrange for a representative to contact you or suggest that the product be repaired by a dealer service technician.

If product repair or return is required, we will provide you with a R6?G<>1SG?@:<7]3?7:>1number and shipping instructions to return the product to the proper facility. If the product is under warranty, we will ask you to provide proof of purchase, such as a copy of your invoice. Please be sure to include the R6?G<>1SG?@:<7]3?7:>1number on the package you are returning. Q<:2G9?8

<6?G<>621E7?@:G?131R6?G<>1SG?@:<7]3?7:>1>G4O6<193>>:?1O61<6D37<62C

Freight costs for product returns are the responsibility of the customer. Products under warranty will be repaired or replaced at our sole discretion and returned at our expense. Products outside the warranty limits will be repaired and returned with costs invoiced to the customer. We are not responsible for shipping damages. We will, however, help you file a claim with the freight carrier. Written repair estimates are available.

DentalEZ warrants the EverLight to be free of defects in material and workmanship, under normal usage, under the following terms:

Z75@?1[:4D:>6>?8I N3<<3> ?B1Q6 <7:2 I

Structural Members: Fixed Arm, Adjustable Arm and Handles 3 Years from date of installation* Switches, LED Driver, Lens/LED 6 Years from date of installation*

Please note the following additional terms of our warranty and return policy:

H Warranties cover manufacturing defects only and do not cover defects resulting from abuse, improper handling, cleaning, care

or maintenance, normal wear and tear or non-observance of operating, maintenance or installation instructions. +37AG<61?:

G8613G?@:<7]621D3<?81:<13>13G?@:<7]621<6D37<10397A7?B1;:7281?@781E3<<3>?BC

HZ73O7A7?B1781A747?621?:1<6D37<1:<1<6DA39646>?1:01?@6126069?7;61D<:2G9?13?1:G<18:A612789<6?7:>C1SAA1:?@6<1A73O7A7?768=17>

D3<?79GA3<1A73O7A7?B10:<12343568=17>9AG27>5=1E7?@:G?1A747?3?7:>=19:>86^G6>?73A1:<17>9726>?3A1234356813<616_9AG262C

H THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NO EMPLOYEE, REPRESENTATIVE OR DEALER IS AUTHORIZED TO CHANGE THIS WARRANTY IN ANY WAY OR TO GRANT ANY OTHER WARRANTY.

WARR ANTY REPA IRS: Pa rts repair ed or repla ced on a pr oduct th at is in warranty will be warranted for the duration of that product's original warranty.

NON-WARRANTY REPAIRS: The warranty on parts either repaired or replaced on an out-of-warranty product will cover the repaired part only and will be for the time frame of a new parts warranty period.

PRODUCT RETURN: Opened products or product returns more than a year old cannot be returned for credit. There will be a 15% ($25.00 minimum) restocking charge on all items authorized for return.

* Provided conditions defined in the Instruction Manual are met.

EverLight® 25

Wiring Schematic

EverLight

INPUT

100-240 VAC, 50/60 HZ

Black (Line)

White (Neutral)

Green (Ground)

OUTPUT

12 VDC, 40 W

Power Supply

26 Installation, Operation and Care Manual

EMC Information

Guidance and manufacturer’s declaration - electromagnetic emissions The Everlight Model EVLCE is intended for use in the electromagnetic environment specified below. The customer or the user of the Model EVLCE should assure that it is used in such an environment.

Emissions test Compliance Electromagnetic environment – guidance

RF emissions

CISPR 11

Group 1

The Model EVLCE uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.

RF Emissions

CISPR 11

Class A

The Model EVLCE is suitable for use in all establishments, other than domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for

domestic purposes. Harmonic emissions

IEC 61000-3-2

Class A,

Not Applicable

Voltage fluctuations/flicker emissions

IEC 61000-3-3

Class A

Not Applicable

●

Use only replacement cables listed in Parts Section, Page 24. Other cables and accessories may negatively affect EMC performance.

●

When the Everlight is used adjacent to other equipment, observe the light to verify normal operation.

— WARNING —

EverLight® 27

EMC Information

Guidance and manufacturer’s declaration – electromagnetic immunity The Everlight Model EVLCE is intended for use in the electromagnet environment specified below. The customer or the end user of the Model EVLCE should assure that it is used in such an environment.

Immunity test

Electromagnetic discharge (ESD)

IEC 61000-4-2

Electrical fast transient/burst

IEC 61000-4-4

IEC 60601 Test level

+6 kV contact

8 kV air

+2 kV for power supply lines

+1 kV for input/output lines

Compliance level

6 kV contact

8 kV air

+2 kV for power supply lines

+1 kV for input/output lines

EverLight

Electromagnetic environment

- guidance Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %. Mains power quality should be that of a typical commercial or hospital environment.

Surge

IEC 61000-4-5

Voltage dips,

short

interruptions and

voltage

variations on

power supply

input lines

IEC 61000-4-11

Power frequency (50/60 Hz) magnetic field IEC 61000-4-8

+1 kV differential mode

2 kV common mode

<5 % U (>95 % dip in U

)

for 0.5 cycle

40 % UT (60 % dip in U

)

for 5 cycles

70 % UT (30 % dip in U

)

for 25 cycles

<5 % U (>95 % dip in U

)

for 5 sec

1 kV differential

+ mode

2 kV common mode

<5 % U (>95 % dip in U for 0.5 cycle

40 % UT (60 % dip in U for 5 cycles

70 % UT (30 % dip in U for 25 cycles

<5 % U (>95 % dip in U

for 5 sec

3 A/m 3 A/m

Mains power quality should be that of a typical commercial or hospital environment.

)

Mains power quality should be that of a typical commercial or hospital environment. If the user of the Model EVLCE requires

)

continued operation during power mains interruptions, it is recommended that the Model EVLCE be powered

)

from an uninterruptible power supply or a battery.

Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.

28 Installation, Operation and Care Manual

Radius

JUNCTION

BOX

4-3/4"

Radius

1/2" Diameter

Hole

(Six Required)

Ceiling Mount Light

Full-Size Template

PN: 2677-069A

Ø1-1/2" Hole for

Wiring Through Wall

Drill Hole Size Depends on

Size of Wall Fastener Chosen

(4 Places)

10"

3/4"

6-3/4"

8-3/4"

17-1/2"

16"

12"

Wall Mount Light

Full-Size Template

PN: 2677-070A

2500 Highway 31 South

Bay Minette, Alabama 36507

1-866-DTE-INFO

Fax: (251) 937-0461

www.dentalez.com

PN: 2717-241B March, 2011

DentalEZ everLight EVLCE Installation, Operation & Care Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Ta b l e o f C o n t e n t s

Section I Introduction

Specifications

Classifications

Dimensions

Light Head Range of Motion

Packaging

Section II Installation

Tr ack M oun t A s se m bly

Ceiling Mount Assembly

Wall Mount Assembly

Cabinet Mount Assembly

Section III Operation

Light Switch

To u c h p a d s

Positioning Light

Eliminating Adjustable Arm Drift

Section IV Care

Cleaning & Disinfecting

Section V User Service Information

Tr ou b l e s h oo t i n g

Service Instruction

Section VI Parts List/Diagrams

Light Arm

Light Head

Drop Post

Product Support Services

Wiring Schematic

EMC Information