Page 1
23001 Industrial Blvd, Rogers, MN 55374 / 1-866-527-7637 / www.motoalliance.com
VIPER PLOW SYSTEM / Can Am/Bombardier Outlander
2008-09 400/500/650/800 MA11142
Thank you for purchasing the premium VIPER PLOW system. You now have a top-of-theline plow system to using for shoving aside snow and dirt with the use of your ATV. Please
note the following instructions and heed all warnings.
WARNING!!!
SEVERE INJURY OR DEATH MAY RESULT IF YOU IGNORE ANY OF
THE FOLLOWING.
−Read the Plow Operator’s Manual, the Winch Operator’s Manual, and all warning labels
before operating.
−Operate ATV at a walking speed with the blade installed. Do Not exceed 5mph (8 km/h)
even with the blade up.
-Plow Cautiously, impact with a hidden or stationary object may cause the ATV to stop
suddenly or go out of control.
--Do Not operate the ATV on slopes greater than 10° with the plow installed.
−Do Not stand or ride on the plow.
Stay clear of moving parts and joints. Keep others away when operating or adjusting plow.
−Inspect the plow mechanism, fasteners, cable, and adjustments before operating. Replace
all worn or damaged parts before operating.
−Lower the plow to the down position before leaving the ATV
unattended.
www.motoalliance.com
1-866-527-7637
Page 2
PARTS LIST
1 Plow Mount
1 Plow Mount Strap
4 5/16-18 X 1 1/2 Hex Bolt
4 5/16 Flat Washer
4 5/16-18 Lock Nut
3 3/8-16 X 1 Hex Bolt
3 3/8 Flat Washers
3 3/8-16 Nylock Nuts
CAUTION
USE EXTREME CAUTION WHEN DRILLING
THROUGH THE SKIDPLATE. EVERY
EFFORT HAS BEEN MADE
TO ENSURE THAT THE HOLE POSITIONS
ON THE CROSSMEMBER WILL NOT ALLOW
THE DRILL BIT TO
CONTACT ANYTHING ELSE ON THE BIKE.
BUT VARIATIONS IN MANUFACTURING
AND INSTALLATION MAY
CHANGE THAT. KEEP AWAY ALL HANDS
AND LIMBS THAT MAY BE IN THE PATH OF
THE ROTATING BIT.
ONLY DRILL THROUGH THE SKIDPLATE
AND NOTHING ELSE ON THE BIKE. NOT
DOING SO MAY
SERIOUSLY DAMAGE/INJURE THE BIKE
AND OPERATOR.
CAUTION
FAILURE TO TIGHTEN THE
MOUNTING BRACKET BOLTS MAY
CAUSE SERIOUS DAMAGE
TO YOUR PLOW MOUNT AND BIKE.
BE SURE TO TIGHTEN THEM
SNUGGLY.
Plow Mount Assembly:
1. Remove the four bolts as shown in
figure 1.
Figure 1 - Remove Bolts
2. Place the plow mounting base plate into
location as shown in figure 2. Secure with four
5/16-18 X 1 1/2 hex bolts, 5/16 flat washers and
5/16-18 lock nuts all supplied in the plow
mounting kit.
Note: Do not tighten at this time.
Figure 2 - Install Plow Mount
www.motoalliance.com
1-866-527-7637
Page 3
3. Place the plow mounting strap into
location as shown in figure 3. Secure with two
3/8-16 X 1 hex bolts, 3/8 flat washers and 3/8-16
lock nuts.
Tighten all hardware at this time.
Figure 3 - Plow Mount Strap Location
Plow Installation:
1. Slide the plow into position with the
tubes under the ATV. Lift the end of
the tube assembly into position so
the holes in the tube wings line up
with the 3/8” holes in the frame
brackets (Figure 2).
2. A Phillips head screwdriver may be
used to align the holes. Insert both
3/8” pins and hook the retaining clips
on the ends of the pins to secure the
plow to the ATV.
3. The plate should now be a
permanent part of your ATV and will
not interfere with clearance. The
plow can be easily attached and
detached on the welded u-bolt with
the clevis hook on a winch or a
manual lift assembly.
Plow mount installation is now complete.
www.motoalliance.com
1-866-527-7637
Loading...