Denali POWERHUB2 Installation Instructions Manual

ELC.00.30000

1 2 3 4 5 6

POWERHUB2

Kit Contents

Power Distribution Module

WARNING! – When mounting electronics to the

front fender, forks, fairing, or handlebars, you must
turn the handlebars fully left and right and fully
compress & uncompress the suspension to ensure
the wires will not bind and have enough slack for
your motorcycle to operate properly.

PLEASE READ BEFORE INSTALLING

TWISTED THROTTLE products should be installed by a
qualified, experienced motorcycle technician. If you are
unsure of your ability to properly install a product, please
have the product installed by your local motorcycle
dealer. TWISTED THROTTLE takes no responsibility for
damages caused by improper installation.

Medium strength liquid thread-locker (i.e., "Locktite")
should be used to secure all screws, bolts, and nuts.

All screws, bolts, and nuts should be checked after
driving the first 30 miles (50 km) to ensure that all are
tightened to the proper torque.

All screws, bolts, and nuts, including all replacement
hardware provided by TWISTED THROTTLE should be
tightened to the torque specified in the OEM mainte­nance manual for your motorcycle. If no torque
specifications are provided in the OEM maintenance
manual, the following torques may be used:

M5.........................................................3.5 ft-lbs (5 Nm)

M6.........................................................6.5 ft-lbs (9 Nm)

M8........................................................16 ft-lbs (22 Nm)

M10......................................................32 ft-lbs (43 Nm)

M12..................................................... 55 ft-lbs (75 Nm)

- 6 Mini ATC Fused circuits for a total of 30 amps

- Each circuit can be switched or unswitched

- Wiring harness included

- Adhesive Velcro included

.............................................................

Features:

Twisted Throttle LLC
570 Nooseneck Hill Rd
Exeter, RI 02822

Phone: [phone]
Fax: [phone]
www.twistedthrottle.com

Instruction Rev: 01

Power Hub

Qty.........................1

2

Ring Terminal

Qty.........................1

3

Posi-Tap

Qty........................2

1

4

Velcro

Qty..................1 Set

Kit Contents

DENALI

BATTERY

TAP TO SWITCHED
+12V SOURCE WIRE

POWERHUB2 // Power Distribution Module // ELC.00.30000

Constant Example

SWITCHED +12V POWER

TAP TO SWITCHED
+12V SOURCE WIRE

GROUND WIRE

Wiring Instructions

Note: This drawing is not to scale. Components are enlarged for illustrative purposes only.

Wiring Diagram

(1) Connect the POWERHUB2 to your battery.

Start by connecting the red wire from the POWERHUB2 to the positive terminal of your battery. Connect the black wire from the POWERHUB2 to the negative terminal of your battery.

(2) Tap a switched power source on your motorcycle.

Use the “Posi-Tap” to tap the yellow wire to a switched 12V power source on your motorcycle. A switched power source is any wire that is +12 VDC when you motorcycle is turned on and 0 VDC when your
motorcycle is turned off. Refer to your service manual or local mechanic to find a suitable switched power source for you specific motorcycle. On BMW canbus motorcycles, use either the can bus adapter
(EC.02350, sold separately), or tap the original BMW power socket positive wire.

(3) Connecting your devices to the POWERHUB2.

Notice that the POWERHUB2 has 6 circuits. Each circuit has an output bus, ground bus, and 2 fuse positions. To connect a device, start by inserting the proper amperage Mini ATC fuse into either the
switched or constant fuse position in circuit 1. Then, connect the positive wire from your device to circuit 1 output terminal. Connect the ground wire from your device to the circuit 1 ground bus terminal on
the POWERHUB2.

Note:

The position of the fuse simply determines whether your device has power when the motorcycle is turned off. The switched fuse position will only allow power to the device when the motorcycle is turned on, while the constant fuse position will allow power to your

device even when the motorcycle is turned off.

1

Switched Example

2

DENALI

+12V DC Wire

123456

Switched

Constant

1 2 3 4 5 6

1 2 3 4 5 6

1 2 3 4 5 6

1 2 3 4 5 6

GROUND BUS

+12V OUTPUT BUS