Page 1
Delvcam
DELV-SDI10-16x9
User Guide
Page 2
General Information
Thank you for choosing our TFT LCD (liquid crystal display) monitor. This product
employs integrate circuits, low power consumption, and no radiation emission. It has
fashion designed appearance and good portability. The TFT LCD screen is suitable for
director in inspection of photography effect. Moreover, this product is able to be used
in office, at home, or other proper positions. Please enjoy the benefits of convenience,
safety, and space-saving from this TFT LCD monitor in different ways.
To ensure the best use of this product, please read this manual carefully
beforehand.
CAUTIONS
1. Please use the adapter attached in the accessories.
2. Please keep away from strong light while using this product in order to
obtain the clearest and the most colorful pictures.
3. Please avoid heavy impact or drop onto the ground.
4. Please do NOT use chemical solutions to clean this product. Please wipe
with a clean soft cloth to maintain the brightness of the surface.
5. Please follow the instructions and trouble-shootings to adjust the product.
Other improper adjustment may result in damage. Any further adjustment
must be performed or conducted by a qualified technician.
6. Please unplug the power and remove the battery if long-term no-use, or
thunder weather.
Page 3
Table of Contents
1. PRODUCT DESCRIPTION -----------------------------------------
2. REMOTE CONTROL-------------------------------------------------
3. POWER SOURCE ----------------------------------------------------
4. SETTING MENU -------------------------------------------------
5. ACCESSORIES --------------------------------------------------------
6. PARAMETER ----------------------------------------------------------
7. TROUBLESHOOTING ----------------------------------------------
8. REMARK---------------------------------------------------------------
Page 4
1. PRODUCT DESCRIPTION
1．Power:ON/OFF ；switch concurrence battery indicator light (red while
standby; green while working)。
2．Infrared signal receiver (work with remote control).
3．A/V: circularly switch among HDMI, YPbPr, Video 1, Video 2, and SDI
(Note
: SDI optional).
►: Right selection key, to select items on OSD menu. Press to adjust
4．
brightness among 6 levels.
5．
◄: Left selection key, to select items on OSD menu.
6．MENU：To activate OSD (on-screen display) menu. Long press to
zoom in/out pictures automatically when receiving HDMI
(High-Definition Multimedia Interface) signals.
7. +: Volume up, or value up while using menu setting functions.
8. –: Volume down, or value down while using menu setting functions.
1
Page 5
9．SDI signal output.
10．Video 1 signal input.
11．Video 2 signal input.
12．Audio signal input.
13．SDI (Serial Digital Interface) signal input.
14．Y signal input.
15．Pb signal input.
16．Pr signal input.
17．HDMI (High Definition Multimedia Interface) signal input.
18. Speakers
19．4-pin XLR DC power input.
20．DC power input.
21．EAR: Earphone jack
2
Page 6
2. REMOTE CONTROL
1．Power
2．Mute button
3．Display switch among HDMI、YPbPr、Video 1, Video 2, and SDI
(optional, must with necessary equipment) circularly.(Note: SDI
optional)
4．MENU: enter menu function setting
5．▲: Up move; or change brightness among 6 levels
6．▼: Down move
7．◄: Left move; or volume down; or increase the function values in
menu settings
8．►: Right move; or volume up; or decrease the function values in menu
settings
3. POWER SOURCES
This product package comes with a 12V/1.5A DC adapter plug into the
DC power input (See PRODUCT DESCRIPTION 20).
Also, this product is capable to use the power from your camcorder via
the 4-pin XLR interface (See PRODUCT DESCRIPTION 19).
4. SETTING MENU
Before setting the menu functions, please make sure the device is
connected correctly.
3
Page 7
When power on, press “MENU” on the device (See PRODUCT
DESCRIPTION 5) or on the remote controller (See REMOTE
CONTROLLER 4). The menu of function setting will display on the screen.
Press ◄/► buttons on the device or
/ buttons on the remote controller
to select items on the left of the display. Then press + / – buttons on the device
or
/ buttons on the remote controller to change the values.
The following pictures are the setting displays of different modes.
1.OSDYPbPr/HDMI/SDI setting menu 2．Miscellaneous setting menu under
(Note: SDI optional) YPbPr/HDMI/SDI modes enter
via
item to a new page.
Picture: YPbPr/HDMI/SDI setting screen
3．OSD AV setting menu (Video 1/Video 2)
The auto-detected AV format displays at the bottom of the screen.
Picture: AV setting screen
4
Page 8
4．Icon description:
Icon Name Function
Brightness Adjust the level of brightness
Contrast Adjust the level of contrast
Saturation Adjust the level of saturation
Tint Adjust the tint of image
OSD H-Position Adjust the on-screen-display horizontally
OSD V-Position Adjust the on-screen-display vertically
Reset Select “Yes” to reset the adjustment as
Color temperature
Red
Green
manufacture parameters.
Choose the color temperature. Options:
User, 6500ºK, 7500 ºK, or 9300 ºK.
Note: Only can available under “User”
mode to meet the color value you need.
Blue
Language Choose language between English and
Miscellaneous Enter to next page (See picture below) for
Exit OSD Select “Exit” to quit the on-screen-display
Display mode Shift display mode between 4:3 and 16:9.
Sharpness Adjust the sharpness of picture
OSD Duration Adjust the display duration of OSD from
Chinese
miscellaneous selections
menu.
5-100 seconds.
5
Page 9
5. Accessories
1 2 3 4
1. Remote control 1 piece
2. 12V DC adapter 1 piece
3. User manual 1 piece
4. HDMI cable
(Optional). 1 piece
6. MAIN PARAMETERS
Panel Size
Screen Resolution
Brightness
Contrast
Viewing Angle
Input Voltage
Input Signal
SDI/HDMI/YPbPr Mode
Color System
Current
Standby Current
10.1’’ T FT LCD (16:9)
1024×600
250cd/㎡
500 : 1
140°/ 110°(H/V)
DC 12V (XLR DC Connection)
HDMI,YPbPr,AV1/2,SDI(Note:SDI
optional)
480i/p、576i/p、720p、1080i(50/60)、
1080p(50/60)
PAL/NTSC
500mA
≤50mA
Power Consumption
Audio Output
Mounts Process
Size:(long × wide × high)
Weight
≤6W
≥250mW
Standard VESA (75mm) Sockets
259mm×170mm×36.5mm
1144g
6
Page 10
7. TROUBLE SHOOTING
1. Only black-and-white display:
Check whether the color saturation and brightness are properly setup.
2. Power on but no pictures:
Check whether the cables of Video, HDMI, DVI (Digital Visual Interface),
and/or SDI (optional) are correctly connected. Please use the standard
power adapter coming with the product package. Improper power input
may cause the device.
3. Wrong or abnormal colors:
Check whether the cables are correctly and properly connected. Broken or
loose pins of the cables may cause a bad connection.
4. Remote controller doesn't work:
Check whether the battery is well charged and properly installed into the
device. The signal of the remote controller may interfered by some
obstacles or obstructions.
5. When on the picture shows size error:
Long press“MENU” to zoom in/out pictures automatically when receiving
HDMI (High-Definition Multimedia Interface) signals.
5. Other problems:
Please press “MENU” button and choose
default values.
to reset to manufactory
8. NOTE
It is normal to see some bright lines appear on the screen when turn off the
device.
7
Loading...