Delta Electronics VFB25ADL, VFB25ACL Installation And Operating Instructions Manual

INSTALLATION AND OPERATING INSTRUCTIONS
VFB25 LIGHT SERIES FAN / LIGHT / NIGHT LIGHT
READ AND SAVE THESE INSTRUCTIONS
General Safety Information
1. Do not install this ventilating fan where air temperature
may exceed 40°C (104°F).
2. Make sure that the electric service supply voltage is AC
120V, 60Hz.
3. Follow all local electrical and safety codes, as well as the
Nation Electrical Code (NEC) and the Occupation Safety and Healthy Act (OSHA).
4. Always disconnect the power source before working on or
near the ventilating fan, motor or junction box.
5. Protect the power cord from sharp edges, oil, grease, hot
surfaces, chemicals or other objects.
6. Do not kink the power cord.
7. Do not install the unit where ducts are configured as shown
in Fig. A.
8. Provide suction parts with proper ventilation.
9. This unit is UL listed for use over a bathtub or shower
when installed in a GFCI protected branch circuit.
10. These ventilating fans are intended for residential usage
only.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
4. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating Refrigeration and Air Conditioning Engineers (ASHRAE) and local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted ventilating fan must always be vented to the
outdoors.
7. If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.
8. These models are UL listed for tub and shower enclosures.
9. Do not use this unit with any other solid-state control
device. Solid-state controls may cause harmonic distortion, which can cause motor humming noise.
10. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
11. NEVER place a switch where it can be reached from a tub
or shower.
12. Not to be installed in a ceiling thermally insulated to a
value greater than R40. (This is required for installation in Canada only)
CAUTION
1. To reduce the risk of electric shock, please disconnect the
electrical supply circuit to the fan before installing
2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. Not for use in cooking area. (Fig. B)
This product must be properly grounded
4.
MODEL VFB25ADL / VFB25ACL
Turning angle too large Duct shrink
Too many elbows Elbow near the body
Body
Fig. A
light kit.
Cooking area
Fig. B
1.
base bulb
12.0
SUPPLIED ACCESSORIES
Part name
Appearance Quantity
installation work.
MODEL VFB25ADL / VFB25ACL
2.
Grille
Long Screw
(M4×25)
Screw
(M4×6)
Screw
(M4×12)
Screw
(M4×30 Black)
Nut
(M4×4.4)
Suspension
bracket
(6.10 inch)
Suspension
bracket
(11.81 inch)
Suspension
bracket
(13.98 inch)
Grille
bracket
(9.68 inch)
GU24
lamp (26W)
E12 base bulb
lamp (4W)
INSTALLATIONS
A. Install with wood frame
1
6
Main Body
1
Long Screw(M4××××25)
3
B. Install with joist
2
1. Choose the installation type according to the fig as below:
1
1
1
1
1
Spacing A on center joists Insert Suspension bracket Suspension bracket No.
12.0 inch Refer to Fig A-01, A-02
16.0 inch Refer to Fig B-01, B-02
19.2 inch Refer to Fig B-01, B-02
24.0 inch Refer to Fig B-01, B-02
I,II I,II,III I,II,III I,II,III
1-1 Type12 inches between joists
1
1
Joist Joist
A-01
Model No. VFB25ADL VFB25ACL
Install Dim. (in.)
10.2 ╳ 10.2 10.2 ╳ 10.2
1. Body installation
1-1. Construct the wood frame(not provided) with 30mm square bar and attach it to the ceiling joist. 1-2. Attach the duct connector to the wood frame with taping screw.
Duct connector
Wood frame
Taping screw
1-3. Insert the body into the wood frame and connect it to the duct connector. Secure the body on wood frame with taping screws. 1-4. Follow step 2 to 5 of installation to complete the
Wood frame
Screw M4××××12
Bracket I
Joist
Tab
Bracket II
Joist
Long Screw(M4××××25)
1-1.1 Insert the suspension bracket into the bracket cover of
adaptor side and select one of suspension bracket of the
back of the fan body.
1-1.2 Insert the fan between joists. Make sure the fan body is
level and perpendicular with the joist.
1-1.3. Ensure the distance between ceiling and fan body for the
thickness of grille.
1-1.4 Secure the suspension bracket to joists by using screw(M4
×12-2pcs each).
1-1.5. Secure the suspension bracket to fan body by using screw.
A-02
16.0
1-1.6. Follow step 2 to 5 of installation to complete the
3-3. Connect wires as shown in wiring diagrams.
installation work. 1-2 Type16/19.2/24 inches between joists
19.2
24.0
Joist Joist
MODEL VFB25ADL / VFB25ACL
3.
B-01
Screw M4××××12
Bracket I
Tab
Bracket II
Joist
1-2.1 Insert the suspension bracket into the bracket cover of
adaptor side and insert the suspension bracket and
into the back of the fan body.
1-2.2 Insert the fan between joists. Make sure the fan body is
level and perpendicular with the joist.
1-2.3 Ensure the distance between ceiling and fan body for the
thickness of grille.
1-2.4 Secure the suspension bracket to joists by using screw
(M4×12-3pcs each).
1-2.5 Secure the suspension bracket to fan body by using screw.
1-2.6 Follow step 2 to 5 of installation to complete the
installation work.
2. Duct connection
2-1. Insert the duct into the duct connector and tape all
ductworks connection to make them secure and air tight.
2-2. Install the duct with a gradient 1°~2° to the outside.
Joist
Bracket III
Tab
B-02
3-4. Using wire nuts, connect house power cable to ventilating
fan, light and night light wires.
Wire nut
Compartment
Power cable
3-5. 14 AWG (2.1 mm
used for branch-circuit wiring.
4. Test run and grille attachment
4-1. When the power on, check for abnormal vibration or sound.
4-2. Mount the grille to the grille bracket by mount screw
(M4×30-2 PCS)
4-2-1
Lock screw(M4×30) into the grille bracket, rotate
around the screw out of bracket surface.
2
) is the smallest conductor that shall be
Lamp module bracket
Screw M4××××30
Tape
Body
Ceiling
Grille
Duct
Inspection Hole
3. Connect wiring
3-1. Follow all local electrical and safety codes.
3-2. NEVER place a switch where it can be reached from a tub
or shower.
Outside Inside
Gradient 1°°°°~2°°°°
4-2-2
Insert the grille bracket module(4-2-1) into the main body,
and lock screw(M4×6) to fixed the grille bracket.
Insert Area
Screw M4××××6
4.2-3 Mount the grille into main body by location screw.
Main body
CLEANING
1. Pull down the spring to remove grille.
2. Wash and clean grille. (Use non-abrasive kitchen detergent,
wipe dry with new cloth.)
3. Remove dust and dirt from ventilating fan using a vacuum
cleaner.
4. Using a cloth dampened with kitchen detergent, remove any
dirt from ventilating fan. Wipe dry with new cloth.
5. Replace grille.
Grille Module
DIMENSIONS
4.2-4 Fixed the grille on the main body by screw and nut
respectively.
Lock nut
MODEL VFB25ADL / VFB25ACL
4.
Lock screw (M4××××30)
4-3. Install light bulbs and attach the cover.
GU24 Lamp(26W Max.)
E12 Lamp(4W Max.)
Lock lens cover
5. Operation Model: VFB25ADL, VFB25ACL
5-1. Turn on the power to operate fan ON or OFF. 5-2. Turn on the power to operate main light on/off. 5-3. Turn on the power to operate night light on/off.
MAINTENANCE
WARNING: Disconnect power source before working on unit. Routine maintenance must be done every year.
CAUTION:
1. Never use gasoline, benzene, thinner or any other such
chemicals for cleaning the ventilating fan.
2. Do not allow water to enter motor.
3. Do not soak resin parts in water over 60°C.
SPECIFICATIONS
Frequency
Model No.
VFB25ADL 120 60 48 110 9.6
VFB25ACL 120
Voltage
(V)
(Hz)
Power
Air Flow @ 0.1SP
(W)
40 80
60
(CFM)
Weight
(lb.)
9.6
Note
Light
/Night Light
Light
/Night Light
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY
Delta Electronics Inc.(“Delta Electronics”) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions
1. During the warranty per iod, a replacement for any defective pr oduct will be supplied free of charge
for installation by the consumer. The warranty provided herein do es not cover charges for labor o r other costs incurred in the troubleshooting, repair, removal, and installation service.
2. All returns of defective parts or products must include the product model number, and must be made through an aut horized Delta Electronics d istributor. Authorized returns must be shipped
prepaid. Repaired or replacement products will be shipped by Delta Electronics F.O.B. shipping point.
3. Delta E lectronics shall not be liable for any indirect, incidental, consequential, punitive, or special
damages arising out of or in connection with products use or performance, regard less of the form of action whether in contract, tort (including negligence), strict product liability or otherwise.
4. This warranty does not extend to fluorescent lamp starters and tubes.
5. The warranty does not cover if user does not comply with manufacture’s installation manual.
6. To qualify for warranty service, you must notify Delta Electronics at the address or telephone
number below.
7. Delta E lectronics shall have no liability t o the o riginal owner-user with respect to any defect caused
by abuse, misuse, neglect, improper transportation or storage, improper testing, improper installation, improper operation, improper use, improper maintenance, improper repair, improper alteration, improper modification, tampering or accident of pro ducts or parts thereof, or unusual deterioration or degradation of products or parts thereof due to a physical environment beyond the requirements of products’ specifications.
Address: 4405 Cushing Parkway, Fremont, CA 94538 US Toll Free Number: 1-888-979-9889
Loading...