Delta Electronics TP02G-AS1 User Manual

http://www.delta.com.tw/industrialautoma tion/

Terminal Panels Series

Instruction Sheet

Warning

3 Please read this instruction carefully before use.

Switch off the power before wiring.

3 3 The display panel of TP02 series is waterproof. But please prevent grease, corrosive liquids and sharp objects from

contacting the TP02 series.

3 The TP02 series require 24VDC input power.

communication port; otherwise serious damage may occur. Check all the wiring again before switching on the power.

DO NOT touch any terminal when the power is switched on. DO NOT touch any internal circuit in 1 minute after the power is switched off.

Make sure the groud terminal is correctly grounded in order to prevent electromagnetic

interference.

Please use the fixed support accessory which is packed together with the product provided by Delta. DO NOT tighten the screws out of the normal torque specifications; otherwise serious damage may occur.

DO NOT connect input AC power supply to any of the RS-485

X Introduction

1.1 Model Explanation

Thank you for choosing Delta TP Series. TP02G-AS1 has the features of high resolution 160×32 dots. It provides

multilingual display and two built-in communication ports, one is for RS-232 and the other is for RS-485. RS-232

and RS-485 can be used simultaneously. Besides, it also supports communication and alarm LED indicators. The

user can purchase program copy card (optional) to copy settings and programs quickly and save download time.

 Nameplate Explanation

Production model Power input spec.

Barc od e an d serial number

Versi on

NOTE: The words of “MADE IN XXXXX” will be different due to the manufacturing location. Please refer to the actual product for exact description.

 Model / Serial No. Explanation

TP 02 G AS 1 -

Reserved Reserved

T: Te x t mode G: Graphic mode

LCD Spec.

Series name

1.2 Product Outline

Displaying Area

Escape / Exit Key

1.3 Panel Function Explanation

PANEL COMPONENT EXPLANATION

Alarm LED Indicator

(RED)

RS-232 LED Indicator

(Yellow)

RS-485 LED Indicator

(Green)

Displaying Area Liquid Crystal Module display area. It is used to display current program status.

Status 1: When power is on, LED will blink slowly for three times. Status 2: When there is an abnormal situation, LED will blink quickly along with an alarm sound.

LED will blink when transmits program and communicates via RS-232.

LED will blink when communicates via RS-485.

MODEL :

POWER INPUT :

VX.XX

DELTA EL ECTR ONIC S, IN C MAD E IN XX XXXX X

TP02GAS 1 W 6 05 0004

TP02G-AS1

24Vdc 3W

TP02GA S1W605 0004

Production serial number

Production weeks

Production year (2006)

Production plant (W: Wuijang; T: Taoyuan)

Ver sio n

Production model

Alarm LED Indicator

RS-232 LED Indicator

RS-485 LED Indicator

Function Keys

Arrow Keys

Enter Key

PANEL COMPONENT EXPLANATION

Escape / Exit Key It is used to cancel an incorrect input, or to exit a programming step.

Enter Key It is used to input a value or accept a programming command.

Arrow Keys

Function Keys

UP / Pg Up: It is used to increase the value or move up one page. Pg Dn / DOWN: It is used to decrease the value or move down one page. Left: This key is left direction key and it can be used to select the position of the value. Right: This key is right direction key and it can be used to select the position of the value.

F0 / 0: It is used as a constant 0, or the user can define it as function F0. F1 / 1: It is used as a constant 1, or the user can define it as function F1. F2 / 2: It is used as a constant 2, or the user can define it as function F2. F3 / 3: It is used as a constant 3, or the user can define it as function F3. F4 / 4: It is used as a constant 4, or the user can define it as function F4. F5 / 5: It is used as a constant 5, or the user can define it as function F5. F6 / 6: It is used as a constant 6, or the user can define it as function F6. F7 / 7: It is used as a constant 7, or the user can define it as function F7. F8 / 8: It is used as a constant 8, or the user can define it as function F8. F9 / 9: It is used as a constant 9, or the user can define it as function F9.

1.4 Back Panel

Vertical view (Unit: mm)

1.6 Installation

Please insert TP02 series to the opening hole of panel and tighten the screws. However, if a firm mounting TP02

series to the panel is needed, please use the mounting fixed support accessory which is packed together with TP02

series, then insert the fixed support in the back and tighten the screws.

If the fixed support is not installed well, Delta will not guarantee the waterproof function. The screw torque

should be 4-5(kg-cm). DO NOT exceed this specification when tightening the screws; otherwise TP02 series may be

damaged. Please leave sufficient space (more than 50mm) around the unit for heat dissipation.

Do not install and mount TP02 series in the following environment.

h A location subjected to Airborne dust, metallic particles, oil and smoke, corrosive or

flammable gases and liquids.

h A location where temperature and humidity will exceed specifications.

h A location where vibration and shock will exceed specifications.

 The flat surface should be a UL Type 4 "Indoor Use Only" enclosure or equivalent (IP65 / NEMA4). Please

RS-232

refer to the figures below.

Thickness: 0.5~9 .0mm

Extension port

5 PIN terminal / Wire gauge: 12-24 AWG / Torque: 4.5 lb.-inch

1.5 Dimension

Front panel (unit: mm [inch])

Right side diagram (unit: mm [inch]) Back panel

Mounting dimension (unit: mm [inch])

[3.35]

135~136.5[5.31~5.37]

Thickness Range 0.5~9mm

Y Function Specifications

ITEM TP02G-AS1

Screen Type STN-LCD

Display Color Monochromatic

Backlight

Resolution 160 x 32 dots

Display Range (W) x (H) = 72 x 22 (unit: mm)

Contrast Adjustment 15 levels of adjustment

Language / Font

Font Size ASCII: 5 × 8, 8 × 8, 8 × 12, 8 × 16

Alarm LED Indicator (RED)

RS-232 LED Indicator

(Yellow)

RS-485 LED Indicator

(Green)

Program Memory 256KB flash memory

Serial Communication Port

RS-232 (COM1)

Extension Communication

Port

RS-485 (COM2)

Extension Interface 1. Update firmware version

Battery Cover DC 3V battery for HMI

5 PIN Removal Terminal Include DC 24V input and RS-485 communication input

The back-light automatic turn off time is 1 ~ 99 minutes (0 = do not turn off)

(The back-light life is about 50 thousand hours at 25°C)

ASCII: Alphanumeric (including European characters)

Taiwan: (Big 5 codes) Traditional Chinese Fonts

China: (GB2324-80 codes) Simplified Chinese Fonts

1. Power on indication (Blink for three times)

2. Communication error alarm

3. Special indication by user programming

It will blink when transmitting program and communicating by using RS-232.

It will blink when communicating by using RS-485.

Unsynchronized transmission method: RS-232

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits

Parity: None/Odd/Even, Transmission speed: 4,800bps ~115,200bps

RS-232: 9 PIN D-SUB male

Unsynchronized transmission method: RS-485

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits

Parity: None/Odd/Even, Transmission speed: 4,800bps ~115,200bps

RS-485: 5 PIN removal terminal

2. The slot for program copy card

Z Electrical Specifications

Specifications TP02G-AS1

Display Monochromatic STN LCD

Effective Display Area (W) x (H) = 72 x 22 (unit: mm)

Display Resolution

160×32: ASCII: 5×8, 8×8, 8×12, 8×16

LCD Contrast Adjustment Set by Software, adjust the contrast by the press button in the function table

LCD Backlight Type LED Backlight: Automatic Turn-off Setting

Function / Numeric Keys F0 / 0 ~ F9 / 9, ESC, ENTER and Arrow Keys

External Input Power 24V (3W Max.)

Memory Capacity 256K Byte

CPU Hitachi HD64F3064F

RAM of System 32K Byte

Communication Interface COM1: RS-232 COM2: RS-485

Waterproof Class of Front

Panel

Operating Temperature for

Hardware

Storage Temperature for

Hardware

Vibration

Shock

0 ~ 50°C; 20 ~ 90﹪RH (non-condensing)

5Hz≦f＜9Hz = Continuous: 1.75mm / Occasional: 3.5mm

9Hz≦f≦150Hz = Continuous: 0.5g / Occasional: 1.0g

15g peak, 11ms duration, half-sine, three shocks in each direction per axis,

on 3 mutually perpendicular axes (total of 18 shocks)

IP65 / NEMA4

-20 ~ 60°C

Radiated Emission CISPR11, Class A

Electrostatic Discharge

Immunity

EN61000-4-2

Radiated Immunity EN61000-4-3

Electrical Fast Transient EN61000-4-4

Weight / Dimensions 0.24kg; 147×97×35.5mm (Width(W) × Height(H) × Deep(D))

Cooling Method Natural Air Cooling

[ Program Copy Card

TP02 series provides Program Copy Card Function to copy user program, system function and passwords that is

different from the copy program. It is used to copy the whole HMI environment settings and application programs

to another HMI rapidly. Using Program Copy Card saves time and manpower. The operation is as follows.

 Definition: Program Copy Card → PCC, TP Series → TP

Step 1 Turn the switch on the PCC to TP ÆPCC Turn the switch on the PCC to PCCÆTP Step 2 Insert the PCC into the extension slot of TP Insert the PCC into the extension slot of TP Step 3 Input the power to TP Input the power to TP

Step 4

It will display “remove PCC” on the screen and power on again.

(TP→PCC) (PCC→TP)

It will display “remove PCC” on the screen and power on again.

 HMI Display Message

Step 1

Step 2

Step 3

If the TP model type does not correspond with the model type of program of PCC, TP will display “TP series and PCC is different. Press Enter to Confirm TP series→PCC. Press Esc to Exit”. TP will display “TP→PCC series Please wait!” during transmission. TP will display “Please Remove the PCC and Reboot” when transmission is completed.

(TP→PCC) (PCC→TP)

If there is no program in PCC, TP will display “The PCC is Empty. PCC→TP series is illegal”.

TP will display “PCC→TP series Please wait!” during transmission. TP will display “Please Remove the PCC and Reboot” when transmission is completed.

\ Password Function

If the user forgot the password, the password can be cleared by using the following code: 8888. This universal

code will clear the password and all TP02 series internal programs. The TP02 series will be reset to the factory

settings by using this code also. Please pay close attention when using it.

 The password can be the alphabet from A to Z or the number from 0 to 9. But it must use the function

keys F0 ~ F9 to input the password characters. Please refer to the following table.

Function Key Use Method Function Key Use Method

scrolls in a loop as follows 0→A→B→C→D→E→F→0 scrolls in a loop as follows 1→G→H→I→J→K→1 scrolls in a loop as follows 2→L→M→N→O→P→2 scrolls in a loop as follows 3→Q→R→S→T→U→ V→3 scrolls in a loop as follows 4→W→X→Y→Z→4

F5 It just can be used to be constant 5.

F6 It just can be used to be constant 6.

F7 It just can be used to be constant 7.

F8 It just can be used to be constant 8.

F9 It just can be used to be constant 9.

] Hardware Operation

When the user wants to startup TP02 series, a 24VDC power is needed. After applying 24VDC power to TP02

series, it will enter into the startup display and then enter the user-designed program. Pressing Esc key and

holding on for 5 seconds can return to system menu. There are five selections in the system menu and are

described below.

SELECTIONS EXPLANAION

Use the connection cable (DVPACAB530) to connect the TP02 serial communication

Download Program

port RS-232 to a PC. Then use the TPEdit software to download an application program to TP02.

Use the connection cable (DVPACAB530) to connect the TP02 serial communication

Upload Program

port RS-232 to a PC. Then use the TPEdit software to upload an application program from TP02.

Transfer a program between two TP02 units. 1: transmit programs

Copy Program

2: receive programs When transmit programs and data between two TP02 units. Set one TP02 to “Receive Program” mode and the other TP02 to “Transmit Program” mode. Please use twisted pair wires to connect the two units via the RS-485 ports.

There are 8 items that used to modify TP02 system settings:

1. Communication protocol: Setting the address of TP02, the control port of PLC, and the communication string for either RS-232 or RS-485.

2. Contrast: Adjust the contrast of LCM display screen.

3. Back-light: adjust the automatic turn off time of LCM. Setting range is 00 ~ 99 minutes. If set to 00, the LCM Back-light will not turn off.

4. Buzzer: Used to set the buzzer sound, normal mode or quiet mode.

TP02 Settings

5. Language Setting: Used to set the displayed language. English, Traditional Chinese, Simplified Chinese or user defined language.

6. Password setting: Used to set, enable, and disable the password function. If the password function is enabled, it will require the user to input a password before entering any system menu. The factory password is 1234.

7. Startup display: Used to select the TP02 startup display. User can select “user defined” to use the file that designed by TPEdit and download to TP02.

8. Comm. indicator: The user can determine if the RS-232 and RS-485 LEDs will blink or not during communication.

There are two methods to connect to PLC:

1. Using TP02 serial communication port (COM1) RS-232: set 8-pin DIP switch to RS-485 mode and connect the cable (DVPACAB215 or DVPACAB230) to

PLC Connection

program communication I/O RS-232C of PLC.

2. Using extension communication port (COM2) RS-485: set 8-pin DIP switch to RS-485 mode and connect 5-pin removal terminal of extension communication port to RS-485 of PLC with twisted pair.

Execute the internal program that download from TPEdit or transmitted from other

Execution

TP02 units. When program is in execution, the user can return to system menu by pressing Escape / Exit (Esc) key for 5 seconds.

^ Communication Connection

TP02G may connect to a PC by using connection able DVPACAB515



PC or TP02 / 04G

TO PC (RS-232)

9 PIN D-SUB

PC COM Port

9 PIN D-SUB female

Rx 2 Tx 3

GND 5

TP 02 / 0 4G CO M P o rt 9 PIN D-SUB female

 TP02G may connect to a DVP-PLC by using connection cable DVPACAB215 / DVPACAB230 /

DVPACAB2A30

1. DVPACAB215 / DVPACAB230

TO P C or TP 02 / 04G

25 PIN D-SUB

9 PIN D-SUB

TO TP02 / 04G

9 PIN D-SUB

3 Tx 2 Rx 5 G N D

TO PLC

MINI DIN TERMINAL

2. DVPACAB2A30

TO P C or TP 02 / 0 4G

9 PIN D-SUB

PC / TP COM Port PLC COM1 Port

Tx Rx 3

GND 7

4 5 6 8

PC / TP COM Port

Tx 3 Rx 2

GND 5

7 8 1 4 6

8 PI N M INI D IN25 PIN D-SUB female

4 R x 5 Tx 8 G ND 1,2 5V

PLC COM1 Port

8 PIN M I N I DIN9 PIN D-SUB female

4 R x 5 Tx 8 G ND 1,2 5V

TO PLC

MINI DIN TERMINAL

 The Pin definition of 9 PIN D-SUB

TP 02 / 0 4G COM Po rt

RS-232 9 PIN D-SUB male

3 Tx 2 Rx

5 GN D

_ Battery Life



Battery Life

Temperature (°C) -20 0 20 60

Life (Year) 1.972 2.466 2.712 2.835

The content of this instruction sheet may be revised without prior notice. Please consult our distributors or

download the most updated version at http://www.delta.com.tw/industrialautomation