Delta Electronics DVPPS02, DVPPS01 User Manual

http://www.delta.com.tw/products/plc.asp

DVPPS01

POWER OUTPUT MODULE

DVPPS02

1 Warning

This instruction will be helpful in the installation, electronic specification, function specification and troubleshooting of the DVPPS01 and

DVPPS02.

This is an OPEN TYPE DVPPS series. The DVPPS series should be kept in an enclosure away from airborne dust, high humidity,

electric shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the enclosure,

so as to avoid the hazard to users and the damage to the DVPPS series.

Never connect the AC main circuit power supply to any of the output terminals, as it will damage the DVPPS series. Check all the wiring

prior to power up. To avoid any electromagnetic noise, make sure the DVPPS series is properly grounded

2 Introduction

2.1 Model Explanation

Thank you for choosing DELTA DVP series. DVPPS series is a power module with 2 types that sorted by output circuit. 1. PS01 provides

24VDC and 1A current for output power. 2. PS02 provides 24VDC and 2A current for output power. DVPPS series is only used for Delta DVP

series. DVPPS series is separated from the PLC MPU for better space utilization and easier installation.

PS01

Nameplate Explanation

Input Power Supply Spec.

Output Module Spec.

Barcode and Serial Number

Model Name

Model

MODEL : DVPPS01

INPUT : 100~240VAC 50 / 60Hz

OUTPUT : 24Vdc 1.0A

PS01 0T4360001

PS02

Input Power Supply Spec.

Barcode and Serial Number

Serial Number

Model

Output Module Spec.

MODEL : DVPPS02

INPUT : 100~240VAC 50 / 60Hz

OUTPU T : 24Vdc 2.0 A

PS02 0T4370001

Series name

Power module

Output current

2.2 Product Profile and Outline

PS01

DVPPS01

36.5

Unit: mm

13.3

PS02

100

DVPPS02

32.5

Production number Production weeks Production year (2004) Production factory Ver si o n

Production model

13.3 60

Unit: mm

1 Power LED 1 Power LED

2 Output/input terminal (fixed terminal) 2 Output/input terminal (fixed terminal)

3 DIN rail clip 3 DIN rail clip

4 DIN rail track (35mm) 4 DIN rail track (35mm)

5 I/O terminal label 5 I/O terminal label

6 Nameplate 6 Nameplate

7 Mounting holes

3 Function/Electrical Specification

Model

Item

Power Input

Output Power

Ripple & Noise

Efficiency

Over Load / Short Circuit Protection

Grounding

Operation/Storage Environment

Agency Approvals

Weight (g)

100~240 VAC (-15%~+10%), 50 / 60 Hz 100~240 VAC (-15%~+10%), 50 / 60 Hz

24VDC (±3%), output current: 1A max. 24VDC (±3%), output current: 2A max.

Under 100mV

The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and N

European Community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC

DVPPS01 DVPPS02

Typical at full load Under 240mV

p-p

Typical at full load

p-p

78%~87% Typical at full load

Auto Recovery

(All PLC units should be grounded directly to the ground pole).

Operation: 0℃~55℃ (Temperature), 50~95% (Humidity), Pollution degree 2;

Storage: -25℃~70℃ (Temperature), 5~95% (Humidity)

Underwriters Laboratories, Inc.: UL508 Listed (Industrial Control Equipment)

158 250

4 Installation and Wiring

4.1 Mounting Arrangements and Wiring

■ DIN Rail Installation

The DVPPS can be secured to a cabinet by using the DIN rail that is 35mm

high with a depth of 7.5mm. When mounting the DVPPS on the DIN rail, be

sure to use the end bracket to stop any side-to-side motion of the DVPPS,

thus to reduce the chance of the wires being pulled loose. On the bottom of

the DVPPS is a small retaining clip. To secure the DVPPS to the DIN rail,

place it onto the rail and gently push up on the clip. To remove it, pull down

on the retaining clip and gently pull the DVPPS away from the DIN rail.

Please see the figure on the right:

■ Direct mounting: Tighten M4 screws into direct mount hole.

■ Wiring

Below 6.2

To suit M3.5 screw terminals

Below 6.2

Notes:

1. Please use O-type or Y-type terminals for I/O wiring terminals. The specification for the terminals is

as shown on the left. Tighten PLC terminal screws to a torque of 5~8 kg-cm (4.3~6.9 in-lbs).

2. Please avoid tiny metal material enter DVPPS01/PS02 when screwing and wiring. After finishing

wire, remove the affix that pasted on the heat sink for heat dissipation.

3. Use Copper Conductors Only, 60℃.

4.2 Wiring Notes

■ Environment

store the DVPPS01/PS02 in a dusty, smoky, or corrosive atmosphere.

DO NOT

store the DVPPS01/PS02 in an environment with high temperature or high humidity.

DO NOT

3. DO NOT install PLC on a shelf or on an unstable surface.

■ Power Input Wiring

Power input of DVPPS01/PS02 is AC input; following items should be noticed:

1. Connect the AC input (100VAC ~ 240VAC) to terminals L and N. Any AC110V or AC220V connected to the +24V terminal will

permanently damage the DVPPS01/PS02.

2. Please use wires of 1.6mm and above for the grounding.

3. If the power-cut time is less than 10ms, the DVPPS01/PS02 still operates unaffectedly. If the power-cut time is too long, the

DVPPS01/PS02 will stop operating and all the outputs will be Off.

5 Trial Run

☼ Power indicator, Running and Test

The “POWER” LED at the front of DVPPS01/PS02 will be lit (in green) if the power is on. If the indicator is not ON, it indicates that the

power supply is not enough or short circuit. Please check your power wiring.

6 Troubleshooting

Judge the errors by the indicators on the front panel. When errors occurred on DVPPS01/PS02, please check:

☼ 「POWER」LED

The “POWER” LED at the front of the MPU will be lit (in green) if the power is on. If the indicator is not on when the MPU is powered up,

please check if power supply is normal. If the indicator is not on when the MPU is powered up and with the input power being normal, it is

an indication that the PLC is malfunction. Please have this machine replaced or have it repaired at a dealer near you.

For heat dissipation. Make sure to

provide a minimum clearance of

50mm between the unit and all

sides of the cabinet. (as shown

below)

> 50mm

DVP MPU

> 50mm> 50mm

> 50mm