Delta Electronics DVPDU-01 User Manual
DVPDU-01 Digital Setup Display
Instruction Sheet
1 WARNING
Please power down the MPU of the
PLC prior to install the DU-01, which
is connected via a high-density
connector. Also please read the
figures on the right for operation
correctly to prevent damage.
2 INTRODUCTION
DU-01 Digital Setup Display has two operation modes, TS-01 and
TC-01. The mode selection switch locates at the back of the
DU-01. Factory setting is TS-01 mode. The current operation
mode will be displayed every time when power up.
TS-01
1. In TS-01
mode, DU-01 (specified as TS-01 hereof) has the following functions:
TC-01
• Read/Write both the internal devices of PLC (e.g. perpetual calendar, bit devices (X, Y, M, S)
and word devices (T, C, D)) and the Control Register (CR) inside the extension units.
• Support the read/write 32-bit data register.
• Set Start-up display and power save mode.
• Monitor the devices.
• If connect the accessory cable to ES-series without perpetual calendar, the Time Display will
start from 00-00-00 calculated by the microprocessor of DU-01 (timing error may occur).
• Give RUN-STOP command to PLC.
2. In TC-01
mode, DU-01 (specified as TC-01 hereof) has the following functions for DVP all series:
• Read/write the program P, data register D and file register F from PLC.
• Copy program and data.
• Support the PLC password protection.
Overview of the Product - Names of Parts
1 5
2
3
4
6
7
8
9
ESC
OK
DU-01
Back of the DU-01
P: program area indication
1
(TC-01)
2 W: write (WR) indication (TC-01)
3 R: read (RD) indication (TC-01)
4 “In communication” indication
D: Data Register indication
5
(TC-01)
F: File Register indication
6
(TC-01)
CR: Control Register indication
7
(Extension Module)
8 ER: Error message display
9 Display Area
10
Enter button
K (Decimal), H (Hexadecimal)
11
indication
Contacts & coils of timer /
12
counter indications
Word devices T, C, D, DD
13
indication
indication
(32-bit)
14 Bit devices X, Y, M, S indication
15 Digit backspace / Run (TC-01)
16 Back to previous status
17 Enter number or select device
18 Confirm
19 Enter number or select device
3 INSTALLATION & WIRING
1. Direct mounting to the expansion slot in the MPU of
the EP/EH series
2. Connecting to DVP
series PLC via accessory
cable
Please power down the PLC MPU prior to install the DU-01,
which is connected via a high-density connector. Also please
refer to the figures above for proper operation. Put the
face-up DU-01 slantly in the extension slot, then push it down
in arrow direction. DO NOT push it down vertically to prevent
(No need to shut down the MPU)
damage.
4 TS-01 OPERATION
1. Switch DU-01 to TS-01 mode. (Please see the back of the DU-01)
2. Main Process
Time Mod e
ESC
Press and hold for 3 sec.
Press and hold for 3 sec.
Operation Mode
Auto Save
ESC
YY-MM-DD
Display
Selectio n
HH-MM-SS
ESC
Device
ESC
Selection
X, Y, M, S
T, C, D
CR
DD(32-bit)
Device
Moni tor
Bit
Device
Word
Device
Device Selection
3. Start-up display mode setting (press + buttons simultaneously)
*Note: not include system operation mode setting
4. Please see the back page for detail information about the process of each mode.
Press and hold for 3 sec.
OK
ESC
No Save
OK
OK
Confir m & up date time
OK
Number Selection
OK
Device confirm
ESC
Number Selection
OK
Device conf irm
ESC ESC
Any mode*
Sleep mode
Specify a number
Press and hold for 3 sec.
OK
ESC
OK
Monitor stat us of 8 c onsec utive
devices from the specified number
Press
Specified No.
Display
OK
Force On/Off setting
OK
to complete entering & return
OK
Press and hold for 3 sec.
ESC
Monitor
Pres s +
Mode
Ti me & d ev ic e
content
+
Unti l sh ows
Sleep mode activated if no button is pressed
within 30 seconds
Enter a number
Enter Set Value
5 TC-01 OPERATION
1. Switch the DU-01 to TC-01
mode (please see the back of
the DU-01), and select RD (to
read P, D and F in the MPU of
PLC) or WR (to write the data
TC-01
Indicatio n of the connected MPU model
Indicatio n of internal data storage model
in P, D, F of DU-01 to the MPU
of PLC).
Note: P: Program, D: Data register, F: File register
2. TC-01 Password Key Setting
Password key setting of TC-01 can be set via WPLSoft. The purpose is to read/write to the key-locked
PLC as long as the password setting matches with the one in PLC. To unlock the password key
setting, please use WPLSoft as well.
a) Password Key Setting
In RD or WR mode, press ESC button and hold for 3 seconds or
more to enter password setting. See the figure on the right:
Open WPLSoft [Setting] [TC-01 password key setting].
Select [Enter TC-01 password key], and operate as instructed.
After setting, display shows the figure on the right. (KEY SET),
then press ESC to exit.
b) TC-01 has password key setting, therefore, only if the PLC has no password protection or with the
same password with TC-01 can process the writing. It also writes the password to the PLC for
added protection.
c) Password key clear (KEY CLR): Same as the operation above. Open WPLSoft, select [TC-01
password key clear], and operate as instructed.
3. Clear P, D, F of TC-01: select the device (P, D or F) to be cleared, press
+ simultaneously,
then press ESC.
4. RD mode description:
RD read mode
+
P,D,F selection
Confirm
Device
P(Program)
Reading P (Program).
You can press ESC to
pause reading.
Finish reading.
d1EC is the CHKSUM
of writing program
Finish reading
D (Data Register)
Setting reading range.
(def ault st art & e nd
addresses are latched
area range. User can
re-s et it .)
Enter start address
Enter end address
Reading pro cessing ...
You can press ESC to
pause reading.
Finish reading
F (File Register)
Reading F (file register)
You can press ESC to
pause reading.
2746 is the CHKSUM
of writing data
Finish reading
A
4. WR mode description:
WR writing mode
+
P,D,F selection
Device Confirm
P (P r ogr a m) D (Data Register) F (File Register)
Blink alternatively
Wri ting t o P (Prog ra m)
in PLC.
You can press ESC
to pause writing during
TC-01-> PLC.
Setting reading range.
(def ault st ar t & en d
addresses is latched
area range. User can
Finish writing.
d1EC is the CHKSUM
of writing data.
change it.)
Finish writing
d1EC is the CHKSUM
of writing data.
Finish writing
Finish writing
6 DIMENSIONS & ACCESSORY
ESC
OK
DU-01
Start End +
(File Register) in PLC.
You can p res s ESC
to pause wr iting during
d1EC is the CHKSUM
of writing data.
Connecting to
DVP-PLC COM1
(RS-232 Port)
Writing to F
TC-01->PLC.
Finish writing.
Finish writing
Expansion
COM Port
Various process for operation modes under TS-01 mode
System operation
mode setting
DF
RWP
KHXYMS
PLC calendar setting
RWP
KHXY MS
Device select mode
K
Device select mode
K
Word device
K
T, C, D, DD
ESC
ESC
W
X, Y, M, S
T, C, D, DD
CR ER
TCD
DD
OK
+
Mode selection
Select yy-mm-dd/hh-mm-ss
DF
CR ER
TCD
DD
OK
+
Set the contents
ERCRFDP
FD
PW
ERCR
K
Select device
DD stands for 32-bit data register
K
Select device
FD
PW
ERCR
Move to the digit
to be set
Sleep mo de setti ng
Fill 0 setti ng (fi ll 0 be fore nu mber o r not)
Start-up display setting
(On: activate, Off: deactivate)
(On: allow to c ustomize start-u p display,
Off: Default time display)
On/Off
Field selection
for setting
OK
confirm device
ESC
OK
Confirm device
ESC
Enter Set Value & return
Enter Set Value
ESC
(On: not to display 0, Off: display 0)
uto Save setting
Confi rm & updat e the t ime
OK
ESC
The left four digits show device number 's
FDPW
K
Device status display
FDPW
K
Mov e to t he
dig it t o be set
to monitor mode
OK
Cur rent va lue
Time display mode
ERCR
ERCR
Set the number
ESC
display
Time display mode
Mov e to t he
digit to be set
(Press and hold for 3 sec.)
OK
ESC
The right four digits show 8 consecutive
displays/settings that starts from Y10
ERCRFDPW
Y10 Y11 Y12 Y13
K
Press and hold for 3 sec.until the blinking cursor shows
OK OK
Set device's number
Use to switch between K (decimal) / H (hexadecimal) display mode.
For
32-bit registers, use to move to display the two left-most digits.
At this time, indicator
Both timer and counter have coils & contacts monitor.
Current value
OK OK
display
ESC
wil l lig ht up .
(Press and hold for 3 sec.)
For example:
Display two left-most digits
for 32-bit register.
Enter S et V al ue mode
Device number setting
K
Y14 Y15 Y16 Y17
Y10,Y12,Y15,Y17 are On
(Depends on actual output of the PLC)
Mov e th e bit t o
desired device's
number
ERCRFDPW
Forced On/Off
setting
ESC
The accessory cable connects the DU-01 (the extension COM port of figure above) and
DVP-series PLC COM1 (RS-232) port. Therefore, the DU-01 can be connected to ES/SS/EX
or SA/SX models via the cable, as well as direct installation in the extension slot of EP/EH
models.
7 ERROR CODE TABLE
Code Code Explanation & Troubleshooting
Error-00
Error-01
Error-02
P-read error. PLC is password-locked while the TC01 has wrong or no password
key. Need unlock the password setting on PLC or set password in TC-01 via WPL.
P-write error. PLC is password-locked while the TC01 has wrong or no password
key; or the source model unmatched the destination model.
D-read error. Illegitimate read range (read range only available for the general data
registers of each models, not include special D)
Error-03 D-write error. The source model unmatched the destination model.
Error-04 F-read error. ES series does not have file registers.
Error-05 F-write error. The source model unmatched the destination model.
Error-06 PLC is running. Writing to P is not permitted.
FD
PW
K
ER
CR
K
select device
ESC
OK
confirm CR
Specify CR number
CR number
Specify the expansion
unit number
(0,1,2...7)Expansion unit number
OK
Current value
display
32-bit
ESC
(Press and hold for 3 sec.)
16-bit
OK
Enter Set Value mode
Device select mode
DF
TCD
CR ER
DD
OK
+
PLC st atus di splay
PLC status switch
Device select mode
Time display mode
RWP
KHX YMS
ESC
Loading...