
Warning
This Instruction Sheet only provides descriptions for electrical specifications, general specifications, installation &
wiring, troubleshooting and peripherals. Other detail information about programming and commands is compatible
with SA/SC/SX series; please see PLC Application Manual. For more information about the optional peripheral,
please see individual product manual.
This is an OPEN TYPE PLC. The PLC should be kept in an enclosure away from airborne dust, humidity, electric
shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the
enclosure, so as to avoid the hazard to users and the damage to the PLC.
Never connect the AC main circuit power supply to any of the input/output terminals, as it will damage the PLC.
Check all the wiring prior to power up. To avoid any electromagnetic noise, make sure the PLC is properly
grounded . DO NOT touch terminals when power on.
Introduction
Thank you for choosing DELTA’s PLC DVP series. The DVP-SX series is a 10-point (4DI+2DO+2AI+2AO)
special main processing unit. Besides the same commands and functions as DVP-SA/SX/SC series, 2-CH
12-bit analog voltage/current input and 2-CH 12-bit analog voltage/current output are all bipolar. There is
built-in 2-digit 7-segment display corresponds to internal register directly to display PLC station or
user-defined code.
Product Profile and Outline
1
Status indicator: POWER, RUN,
2-digital 7-segment display
4
COM1 (RS-232) (Rx) indicator
9
COM2 (RS-485) (Tx) indicator
10
COM1 (RS-232)
Communication port (Slave)
Units: mm
11
Mounting hold of the expansion
COM2 (RS-485)
Communication port
17
2 pin removable terminal
(standard accessory)
19
Power input cable
(standard accessory)
20
Battery socket connection
Battery replacement: Please change the battery within 3 minutes, or the
internal data of the PLC (including the program area, RTC and latched
registers) could be lost or destroyed.
22
Battery mount
ENGLISH
Electrical Specifications
Electrical Specifications
Model
Item
DVP10SX11R/T DVP08SM11N DVP08SN11R/T DVP08SP11R/T DVP16SP11R/T
MPU: 24V DC (-15% ~ 20%) (with DC input reverse polarity protection),
Expansion Unit: supplied by the MPU
Fuse 2A / 250V AC -
Power Consumption 5W 1W 1.5W 1.5W 2W
Insulation Resistance
> 5 MΩ at 500 V DC (Between all inputs / outputs and earth)
Noise Immunity
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS: 26MHz~1GHz, 10V/m
Grounding
The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and N
(All DVP units should be grounded directly to the ground pole).
Environment
Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), Pollution degree 2;
Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity); D/A output operation: 0°C ~ 50°C
(temperature)
Vibration / Shock
Resistance
Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
Weight (approx.) (g) 138 / 133 64 88 / 68 90 / 70 96 / 76
Approvals
Electrical Specification of Input Point Electrical Specification of Output Point
Input Type DC (SINK or SOURCE) Output Type Relay-R Transistor-T
Input Current 24V DC 5mA
Current
Specification
1.5A/1 point
(5A/COM)
0.3A/1 point @ 40°C; When the output of Y0
and Y1 is high-speed pulse, Y0 and Y1 =
30mA
Off → On,
X0,X1: above 18.5V DC
X2,X3: above 16.5V DC
Voltage
Specification
30V DC
Active Level
On→Off,
X0~X3 below 8V DC
75VA
(Inductive)
Maximum
Loading
90 W
(Resistive)
9W/1 point
When the output of Y0 and
Y1 is high-speed pulse, Y0
and Y1 = 0.9W (Y0 = 32
Y1 = 10kHz)
Responding
Time
About 10ms (An
adjustment range of 0 ~ 20
ms could be selected
through D1020 and D1021)
Responding
Time
About 10 ms
Y0 and Y1 are specified
points for high-speed pulse
Model Name & I/O Configuration
Input Output
Point
DC24V/5 mA
Sink or Source
-20 ~ 20mA
range(-1,000 ~ +1,000)
-10 ~ +10V
range(-2,000 ~ +2,000)
-20 ~ 20mA
(range:-2,000 ~ +2,000)
-10 ~ +10V
(range:-2,000 ~ +2,000)
Installation & Wiring
3.1 PLC Mounting Arrangements and Wiring Notes
Installation of the DIN rail:
The DVP-PLC can be secured to a cabinet by using the
DIN rail that is 35mm high with a depth of 7.5mm. When
mounting the PLC on the DIN rail, be sure to use the
end bracket to stop any side-to-side motion of the PLC,
thus to reduce the chance of the wires being pulled
loose. At the bottom of the PLC is a small retaining clip.
To secure the PLC to the DIN rail, place it onto the rail
and gently push up the clip. To remove it, pull down the
retaining clip and gently pull the PLC away from the DIN
rail. As shown on the right:
When installing the DVP series
PLC, make sure that it is
installed in an enclosure with
sufficient space (as shown
below) to its surroundings so as
to allow heat dissipation.
DVP
MP
D
D
DD
16AWG (1.5mm) wiring (either single or multiple core) for
I/O wiring terminals. The specification for the terminals is as shown on
the left. PLC terminal screws should be tightened to between 1.95
kg-cm (1.7 in-lbs). Use 60/75°C copper conductor only.
2. I/O signal wires or power supply should not run through the same
multi-wire cable or conduit.
3.2 Wiring Notes
Power Input Wiring
DVP-SX series input power supply is DC input. Please take a note of listed items when operating DVP-SX.
Series.
1. Please make sure the power is at terminals 24V DC and 0V (power range is 20.4V DC ~ 28.8V DC). When
voltage is lower than 20.4V DC, PLC will stop operating, all outputs will turn Off and ERROR LED will flash
continuously.
2. If the power-off time is less than 10ms, the PLC still operates unaffectedly. If the power-off time is too long or
the power voltage drops, the PLC will stop operating and all the outputs will be Off. Once the power is
restored, the PLC will return to operate automatically. (There are latched auxiliary relays and registers
inside of the PLC, please be aware when programming.)
DC Input Type
20.4V~28.8 V
Safety Wiring
Since the PLC is in control of numerous devices, motion of either one device could affect the motion of other
devices, therefore the breakdown of either one device would consequently be detrimental to the whole auto
control system, and danger will thus be resulted. Please use the recommended wiring below for the power
input:
Power supply for AC loads
Power Circuit Protection Fuse (3A)
Power On pilot indicator
Emergency stop
The machinery must provide a quick manual method
disconnecting all system power.
Circuit isolation device (System Power Disconnect)
Utilize the electromagnetic contactor and the relay to be the
isolation unit of the power circuit to prevent the possible
instability of the system when the power is supplied on and off.
DVP PLC MPU (main processing unit)
Grounding
MC
MC
NL
1
1
2
3
4
5
6
8
Guard
Limit
7
Power supply:
AC: 100 ~ 240V AC, 50/60Hz
DC: 24V DC
Input Point Wiring
The input signal of the input point is the DC power DC input. There are two modes of DC type wiring: SINK and
SOURCE, defined as follows:
Sink = Current flows into the common terminal S/S Source = Current flows out of common terminal S/S
Sinking
S/S
X0
Sourci ng
S/S
X0
Loop Equivalent Circuit of Input Point Wiring Loop
DC Type
(DC Signal IN)
SINK Mode
+24V
24G
S/S
X0
24VDC
X0
24VDC
Loop Equivalent Circuit of Input Point Wiring Loop
DC Type
(DC Signal IN)
SOURCE Mode
+24V
24G
S/S
X0
24VDC
X0+24V OV
24VDC
Output Point Wiring
Y0
RY
LED
C0
RELAY O UTP UT
LOAD
POWE R
1. There are two kinds of DVP-SX Series PLC output
modules: Relay and Transistor. For relevant electrical
specification, please refer to the function specification.
2. Be careful with the connection of the common
terminals when wiring outputs. For example, when
wiring DVP12SX11R, output terminal Y0 uses one
common terminal C0, Y1 uses C1, as shown below:
Action indication: When the output point is active, the
corresponding indicator at the front will be on.
3. Isolated circuit: The optical coupler is used to isolate
signals between PLC internal circuits and input
modules.
Analog Input/Output Point Wiring
Shielded*1
Shielded*1
100K
CH0
100K
100K
Note 1:
Please isolate analog input and other power
wiring.
Note 2:
If input signal is in current, please short out
between V+ and I+ terminals.
Note 3:
If the noise interference from loaded input wiring
terminal is significant, please connect a
capacitor with 0.1 ~ 0.47µF 25V for noise
filtering.
V+
I+
COM
CH0
-10V~+10V
*5
CH0
V+
I+
CH1
-20mA~20mA
CH1
24+
24-
DC24V
DC/DC
+15V
-15V
AG
current output
AC drive, recorder,
scale valve...
shielding cable *1
shielding cable *4
AC drive, recorder,
scale valve...
terminal of
power module
class 3 grounding
(100 or less)
converter
Note 4:
Please isolate analog output and other power
wiring.
Note 5:
If the noise interference from loaded input wiring
terminal is significant, please connect a
capacitor with 0.1 ~ 0.47µF 25V for noise
filtering.
Note 6:
Please connect
power module terminal and
analog output module terminal to system
earth point and make system earth point be
grounded or connects to machine cover.
Warning:
DO NOT wire to the No function terminal
注意事項
本使用說明書僅提供電氣規格、功能規格、安裝配線、故障排除及周邊裝置部份說明,其它詳細之程式設計
及指令與
SA/SX/SC
系列相容,詳細說明請見
PLC
技術手冊【程式篇】,選購之周邊裝置詳細說明請見該產
品隨機手冊。
本機為開放型(
OPEN TYPE
)機殼,因此使用者使用本機時,必須將之安裝於具防塵、防潮及免於電擊/衝
擊意外之外殼配線箱內。另必須具備保護措施(如: 特殊之工具或鑰匙才可打開)防止非維護人員操作或意
外衝擊本體,造成危險及損壞。請勿在上電時觸摸任何端子。
交流輸入電源不可連接於輸入/出信號端,否則可能造成嚴重損壞,請在上電之前再次確認電源配線。本體上
之接地端子
務必正確的接地,可提高產品抗雜訊能力。
產品簡介
謝謝您採用台達
DVP
系列可程式控制器。
DVP-SX
機種為10點(
4DI+2DO+2AI+2AO
)特殊主機,除與
SA/SX/SC
主機具有相同的指令集及功能規格,並具有
2CH的12-bit
類比電壓/電流輸入及
2CH的12-bit
類比電壓/電流輸
出,同時均具有雙極性電壓/電流輸出能力。主機並內建2位數的七段顯示模組,直接對應內部暫存器,可用於
顯示站號或客戶自己定義的訊息代碼。
產品外觀及各部介紹
1
電源、運行錯誤及電池低電壓
指示燈
2
RUN/STOP開關
3
COM1 (RS-232)
通訊接收
(Rx)
指示燈
9
COM2 (RS-485)
通訊傳送
(Tx)
指示燈
10
COM1 (RS-232)
通訊口
(Slave)
尺寸單位:
mm
11
銘牌
12
DIN軌糟 (35mm)
15
擴充機固定扣
16
COM2 (RS-485)
通訊口
(Master/Slave)
17
電池蓋
21
電池插座連接
電池安裝
電池安裝電池安裝
電池安裝::::
更換電池時,請在3分鐘內完成,否則
PLC
內部資料(包含程式
區,萬年曆及停電保持暫存器)有可能會消失或被破壞。
22
項 目
DVP10SX11R/T DVP08SM11N DVP08SN11R/T DVP08SP11R/T DVP16SP11R/T
電源電壓 主機:
24V DC(-15% ~ 20%
)(具直流輸入電源極性反接保護),擴充機:由主機供應
電源保險絲容量
2A/250V AC -
消耗電力
5W 1W 1.5W 1.5W 2W
絕緣阻抗
5MΩ
以上(所有輸出/入點對地之間
5 00V DC)
雜訊免疫力
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS: 26MHz ~ 1GHz, 10V/m
接地 接地配線之線徑不得小於電源端
L,N
之線徑(多台
PLC
同時使用時,請務必單點接地)
操作/儲存環境
操作:
0°C ~ 55°C
(溫度),
50 ~ 95%
(濕度);污染等級
2
儲存:
-25°C ~ 70°C
(溫度),
5 ~ 95%
(濕度);
D/A
輸出操作:
0°C ~ 50°C
(溫度)
耐振動/衝擊 國際標準規範
IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC68-2-27 (TEST Ea)
重量(約
, g)
138 / 133 64 88 / 68 90 / 70 96 / 76
認證
輸入點電氣規格
輸出點電氣規格
輸入
形式
繼電器
-R
電晶體
-T
輸入
電流
24V DC 5mA
電流
規格
0.3A/1點 @ 40°C
高速脈波輸出時
, Y0、Y1為30mA
Off → On,
X0、X1為18.5V DC以上
X2、X3為16.5V DC以上
電壓
規格
On → Off,
X0~X3為8V DC以下
75VA
(電感性)
最大
負載
90W
(電阻性)
9W/1點
高速脈波輸出時
Y0、Y1為0.9W
(Y0:
50KHz,Y1:10KHz
)
反應
時間
約
10ms(由D1020及D1021
可
作
0 ~ 20ms
的調整)
反應
時間
約
10 ms
Off → On 20us
On → Off 30us
Y0、Y1
輸出為
高速脈波輸出點
機種型號與
I/O配置
輸入單元
輸出單元
點數
形式
點數 形式
機種 電源
DI AI DI AI DO AO DO AO
繼電器
DVP10SX11T
24VDC
+20%
-15%
4 2
-20 ~ 20mA
(
範圍:
-1,000 ~ +1,000)
-10 ~ +10V
(
範圍:
-2,000 ~ +2,000)
電晶體
-20 ~ 20mA
(
範圍:
-2,000 ~ +2,000)
-10 ~ +10V
(
範圍:
-2,000 ~ +2,000)

安裝及配線
3.1
盤內安裝及配線
DIN
鋁軌之安裝方法
鋁軌之安裝方法鋁軌之安裝方法
鋁軌之安裝方法::::
適合
35mm之DIN
鋁軌,主機欲
掛於鋁軌時,先將
PLC
下方之固
定塑膠片壓入,再將
PLC
由上方
掛上再往下壓即可。欲取下
PLC
時,
PLC
底部下之固定塑膠片,以
起子插入凹槽,向上撐開即可,該
固定機構塑膠片為保持型,當所有
的固定片撐開後,再將
PLC
往上
外方取出,如右圖所示:
PLC
在安裝時,請裝配於封閉式之控制箱內,
其周圍應保持一定之空間(如下圖所示),以
確保
PLC
散熱功能正常。
DVP
MP
D
D
DD
D > 50 mm
配線
配線配線
配線::::
1.
輸出/入配線端請使用
22-16AWG (1.5mm)
單蕊祼線或多蕊線,端子規
格如左所示。
PLC
端子鏍絲扭力為
1.95kg-cm (1.7 in-lbs)
。只能使用
60/75°C
的銅導線。
2.
在配線時請勿請輸入點信號線與輸出點或電源等動力線置於同一線糟
內。
3.2
注意事項
電源端輸入配線
SX
機種為直流電源輸入,在使用上應注意下列事項:
1.
電源請接於
24V DC及0V
兩端,電源範圍為
20.4V DC ~ 28.8V DC
,當電源電壓低於
20.4V DC時,PLC
會停
止運轉,輸出全部
Off,ERROR LED
快速閃爍。
2.
當停電時間低於
10ms時,PLC
不受影響繼續運轉,當停電時間過長或電源電壓下降將使
PLC
停止運轉,輸
出全部
Off
,當電源恢復正常時,
PLC
亦自動回復運轉。(
PLC
內部具有停電保持的輔助繼電器及暫存器,使
用者在作程式設計規劃時應特別注意使用)
直流電源
輸入型式
S/S X0 X1 X2
OV24 VDC
DC/DC
2A
5V
20.4V~2 8.8 V
安全配線回路
由於
PLC
控制許多裝置,任一裝置的動作可能都會影響其它裝置的動作,
因此任
一裝置的
故障都
可能會造成
整個
自動控制系統失控,
甚至造成危險
。所以在電源端輸入回
路
(DVPPS01/DVPPS02)
,建議配置如下的保護回路:
交
流電源
負載
電源回路保護用保險絲
(3A)
電源指示燈
緊急
停止
為
預防突發狀況發生,設置一緊急停止按鈕
,可在
狀況
發生時,切斷系統
電源。
系統回
路隔離
裝置
使用電磁接觸器、繼電器等開關作為系統電源回
路隔離
裝置,可防止電源斷續供應時,造成系統的不穩定。
DVPPS01/DVPPS02本體
接
地
MC
MC
NL
1
1
2
3
4
5
6
8
Guard
Limit
7
MC
電源供應:
交
流
(AC):100 ~ 240V AC, 50/60Hz
直流
(D C):24V DC
輸入點之配線
輸入點之入力信號為直流電源DC輸入,DC型式共有兩種模式接法:
SINK及SOURCE
,其定義如下:
Sink =
電流流入共用端
S/S Source =
電流流出共用端
S /S
Sinking
S/S
X0
Sourcin g
S/S
X0
輸入點回路等效電
路
配線回
路
直流形式
(
DC Signal IN)
SINK 模式
+24V
24G
S/S
X0
24VDC
X0
24VDC
輸入點回路等效電
路
配線回
路
直流形式
(
DC Signal IN)
SOURCE 模式
+24V
24G
S/S
X0
24VDC
X0+24V OV
24VDC
輸出點之配線
Y0
RY
LED
C0
Y0
LED
C0
TRANSISTO R OUTP UT
1. DVP-S系列PLC
輸出模組共有二種:繼電
器及電晶體,其相關電氣規格請參考功能規
格部份。
2.
輸出端在實際配線時,應特別注意共用端的
連接,以
DVP10SX11R
為例,輸出端
Y0
用一
個C0共
同端,另外Y1用C1,如圖所
示:
動作指示:
當輸出點動作時,正面的該點指示燈亮。
3.
隔離回路
:
PLC
內部回路與輸入模組之間
使用光耦合器作信號隔離。
類比輸入/輸出點之配線
CH0
100K
250
隔離線
*1
電壓輸入
-10V~+ 10V
V+
I+
COM
CH0
100K
100K
250
隔離線
*1
電流輸入
-20mA~ +20m A
V+
I+
COM
CH1
100K
*3
*2
AG
AG
隔離線
*1
電壓輸出
變頻器、 記錄器
比例閥
...
隔離線
*4
電流輸出
變頻器、 記錄器
比例閥
...
接至電源 模
組之 端
第三種接 地
( )
接地阻抗 以下
轉換器
CH0
CH1
I+
V+
DC24V
24+
24 -
DC/DC
AG
+15V
-15V
-20mA~20mA
-10V~+10V
*5
註註註註1::::
類比輸入請與其他電源線隔離。
註註註註2::::
如果連接電流信號時,
V+ 及I+
端子請
務必
短路
。
註註註註3::::
如果輸入電壓有
漣波造
成配線受雜訊干擾時
請連接
0.1 ~ 0.47 µF 25V
之電容。
註註註註4::::
類比輸出請與其他電源線隔離。
註註註註5::::
如
果負載
之輸出端
漣波太大造
成配線受雜訊
干擾
時,請連接
0.1 ~ 0.47μF 25V
之電容。
註註註註6::::
請將主機之
端連接到系統接地點,再將系
統接點作第三種接地或接到
配電箱之機殼上。
注意
注意注意
注意::::
空端子
請勿配線。
注意事項
本使用说明书仅提供电气规格、功能规格、安装配线、故障排除及周边装置部份说明,其它详细之程序设计
及指令与
SA/SX/SC
系列兼容,详细说明请见
PLC
技术手册【程序篇】,选购之周边装置详细说明请见该产
品随机手册
。
本机为开放型(
OPEN TYPE
)机壳,因此使用者使用本机时,必须将之安装于具防尘、防潮及免于电击/冲
击意外之外壳配线箱内。另必须具备保护措施(如: 特殊之工具或钥匙才可打开)防止非维护人员操作或意
外冲击本体,造成危险及损坏。请勿在上电时触摸任何端子
。
交流输入电源不可连接于输入/出信号端,否则可能造成严重损坏,请在上电之前再次确认电源配线。本体上
之接地端子
务必正确的接地,可提高产品抗噪声能力
。
產品簡介
谢谢您采用台达
DVP
系列可编程序控制器。
DVP-SX
机种为10点
(
4DI+2DO+2AI+2AO
)
特殊主机,除与
SA/SX/SC
主机具有相同的指令集及功能规格,并具有
2CH的12-bit
模拟电压/电流输入及
2CH的12-bit
模拟电压/电流输
出,同时均具有双极性电压/电流输出能力。主机并内建2位数的七段显示模块,直接对应内部寄存器,可用于
显示站号或客户自己定义的信息代码。
产品外观及各部介绍
1
电源、运行错误及电池低电
压指示灯
2
RUN/STOP开关
3 2
位数七段显示模块
4
COM1 (RS-232)
通信接收
(Rx)
指示灯
9
COM2 (RS-485)
通信传送
(Tx)
指示灯
10
COM1 (RS-232)
通讯口
(Slave)
尺寸单位:mm
11 铭牌
12
扩展连接口
13
扩展定位孔
14 DIN轨糟 (35mm)
扩展固定扣
16
COM2 (RS-485)
通讯口
(Slave)
17
电源输入口
18
2 pin
脫落式端子(标准附件
)
电池盖
21
电池插座连接
安装
安装安装
安装::::
更换电池时,请在3分钟内完成,否则
PLC
内部数据(包含程序区,
万年历及停电保持寄存器)有可能会消失或被破坏。
22
项项项项 目目目目
DVP10SX11R/T DVP08SM11N DVP08SN11R/T DVP08SP11R/T DVP16SP11R/T
电源电压
主机:
24V DC(-15% ~ 20%)
(
具直流输入电源极性反接保护),扩展:由主机供应
电源保险丝容量
2A / 250V AC -
消耗电力
5W 1W 1.5W 1.5W 2W
绝缘阻抗
5MΩ
以上(所有输出/入点对地之间
500V DC)
噪声免疫力
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS: 26MHz~1GHz, 10V/m
接地 接地配线之线径不得小于电源端
L,N
之线径(多台
PLC
同时使用时,请务必单点接地)
操作/储存环境
操作:
0°C ~ 55°C
(温度)
,
50 ~ 95%
(湿度)
;污染等级
2
储存:
-25°C ~ 70°C
(温度)
,
5 ~ 95%
(湿度)
;
D/A
輸出操作:
0°C ~ 50°C
(溫度)
耐振动/冲击 国际标准规范
IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC68-2-27 (TEST Ea)
重 量(约
, g)
138 / 133 64 88 / 68 90 / 70 96 / 76
认证
输入点电气规格
输入点电气规格输入点电气规格
输入点电气规格
输出点电气规格
输出点电气规格输出点电气规格
输出点电气规格
输入
形式
0.3A/1点 @ 40°C
高速脉冲输出时
, Y0、Y1为30mA
Off → On,
X0, X1为18.5V DC以上
X2, X3为16.5V DC以上
电压
规格
250V AC,30V DC以下 30V DC
动作
位准
On → Off,
X0~X3为8V DC以下
75VA
(電感性)
最大
负载
90W
(電阻性)
9W/1点
高速脉冲输出时
Y0、Y1
为
0.9W(Y0:50KHz,Y1:10KHz)
约
10ms(由D1020及D1021
可
作
0 ~ 20ms
的调整)
反应
时间
約
10 ms
Off → On 20us
On → Off 30us
Y0、Y1
输出为
高速脉冲输出点
机种型号与
I/O
配置
输入单元
输入单元输入单元
输入单元
输出单元
输出单元输出单元
输出单元
点数
机种
机种机种
机种 电源
电源电源
电源
DI AI DI AI DO AO DO AO
-20 ~ 20mA
(
范围:
-1,000 ~ +1,000
)
-10 ~ +10V
(
范围:
-2,000 ~ +2,000
)
-20 ~ 20mA
(
范围:
-2,000~ +2,000
)
-10 ~ +10V
(
范围:
-2,000~ +2,000
)
安裝及配線
3.1
盘内安装及配线
DIN
铝轨之安装方法
铝轨之安装方法铝轨之安装方法
铝轨之安装方法::::
适合
35mm之DIN
铝轨,主机欲挂于铝轨
时,先将
PLC
下方之固定塑料片压入,再
将
PLC
由上方挂上再往下压即可。欲取下
PLC时,PLC
底部下之固定塑料片,以起
子插入凹槽,向上撑开即可,该固定机构
塑料片为保持型,当所有的固定片撑开后,
再将
PLC
往上外方取出,如右图所示:
PLC
在安装时,请装配于封闭式之控制箱
内,其周围应保持一定之空间(如下图所
示),以确保
PLC
散热功能正常。
DVP
MP
D
D
DD
D > 50 mm
配配配配线线线线::::
1.
输
出/入配线端请使用
22-16 AWG (1.5mm)
单蕊祼线
或多蕊线,端子规格
如左所示。
PLC
端子镙丝扭力
为
1.95kg-cm (1.7 in-lbs)
。只能使用
60/75°C
铜导线
。
2.
在配
线时请勿请输入点信号线与输出点或电源等动力线置于同一线糟内
。
3.2
注意事项
电源端输入配线
SX
机种为直流电源输入,在使用上应注意下列事项:
1.
电源请接于
24V DC及0V
两端,电源范围为
20.4V DC ~ 28.8V DC
,当电源电压低于
20.4V DC时,PLC
会停
止运行,输出全部
Off,ERROR LED
快速闪烁。
2.
当停电时间低于
10ms时,PLC
不受影响继续运转,当停电时间过长或电源电压下降将使
PLC
停止运行,输
出全部
Off
,当电源恢复正常时,
PLC
亦自动回复运行。(
PLC
内部具有停电保持的辅助继电器及寄存器,使
用者在作程序设计规划时应特别注意使用)
直流电源
输入型式
X0 X 1 X 2OV24 VDC
DC/DC
2A
20.4V~2 8.8 V
安全配线回路
由于
PLC
控制许多装置,任一装置的动作可能都会影响其它装置的动作,因此任一装置的故障都可能会造成
整个
自动控制系统失控,
甚至造成危险
。所以在电源端输入回路(
DVPPS01/DVPPS02
),建议
配置如下的保护回路:
紧急
停止
为
预防突发状况发生
,设置紧急停止按钮,可在
状况发
生时,切断系统
电源。
系统回
路隔离
装置
使用电磁接触器、继电器等开关作为系统电源回
路隔离
装置,可防止电源断续供应时,造成系统的不稳定。
DVPPS01/DVPPS02本体
接
地
MC
MC
NL
1
1
2
3
4
5
6
8
Guard
Limit
7
MC
电源供应:
交
流
(AC):100 ~ 240V AC, 50/60Hz
直流
(DC):24V DC
输入点之配线
输入点之入力信号为直流电源DC输入,DC型式共有两种模式接法:
SINK及SOURCE
,其定义如下:
Sink =
电流流入共享端
S /S Source =
电流流出共享端
S/S
Sinking
S/S
X0
Sourcin g
S/S
X0
输入点回
路等效电路
配线回
路
直流形式
(DC Signal IN)
SINK 模式
+24V
24G
S/S
X0
24VDC
SINK
+5V
+24V OV
X0
24VDC
输入点回
路等效电路
配线回
路
直流形式
(DC Signal IN)
SOURCE 模式
+24V
24G
S/S
X0
24VDC
+5V
Source Type
X1 X2S/S X0+24V O V
24VDC
输出点之配线
Y0
RY
LED
C0
RELAY OUTPUT
LOAD
Y0
LED
C0
TRANSISTOR OUTPUT
1. DVP-S系列PLC
输出模块共有二种:继电
器及
晶体管
,其相关电气规格请参考功能规
格部份。
2.
输出端在实际配线时,应特别注意共享端的
连接,以
DVP10SX11R
为例,输出端
Y0
用一
个C0共
同端,另外Y1用C1,如图所
示:
动作指示:
当输出点动作时,正面的该点指示灯亮。
3.
隔离回路
:
PLC
内部回路与输入模块之间
使用光耦合器作信号隔离。
模拟输入/输出点之配线
CH0
100K
250
隔离线
*1
电压输入
-10V~+10V
V+
I+
100K
250
隔离线
*1
电流输入
-20mA~+20 mA
V+
I+
COM
CH1
100K
*3
*2
AG
隔离线
*1
电压输出
变频器、记 录器
比例阀...
隔离线
*4
电流输出
接至电源模
块之 端
第三种接地
(接地阻抗 Ω以下
CH0
CH1
CH0
CH1
COM
I+
V+
COM
I+
V+
DC24V
24+
24 -
DC/DC
AG
+15V
-15V
-20mA~ 20m A
-10V~+ 10V
*5
变频器、记 录器
比例阀...
注注注注1::::
模拟输入请与其它电源线隔离。
注注注注2::::
如果连接电流信号时,
V+ 及I+
端子请
务必
短路
。
注注注注3::::
如果输入电压有
涟波造
成配线受
噪声干扰
时
请连接
0.1 ~ 0.47 µF 25V
之电容。
注注注注4::::
模拟输出请与其它电源线隔离。
注注注注5::::
如
果负载
之输出端
涟波太大造
成配线受
噪声
干扰
时,请连接
0.1 ~ 0.47µF 25V
之电容。
注注注注6::::
请将主机之
端连接到系统接地点,再将系
统
接点作第三种接地或接到配电箱之机壳上。
注意
注意注意
注意::::
空端子 请勿配线。