Delta RF 642 User Manual

*2702178_Rev.1*

TYXIA

Installation and User Guide

Wireless receiver

TYXIA RF 642 - 1 channel

Unit compliant with the requirements of directives:

R&TTE 1999/5/CE

Because of changes in standards and equipment, the characteristics given in the text and the illus­trations in this document are not binding unless confirmed by our services.

DELTA DORE

Bonnemain - 35270 COMBOURG - France

E-mail : [e-mail]

• Carefully read these instructions prior to
installation.

• The unit must be installed in compliance with
current standards.

• Always switch off the mains before installing or
servicing the unit.

• Do not attempt to repair the unit yourself; an after­sales service is available.

• Check that the fastenings are suited to the surface
to which the unit will be attached (plasterboard,
brick, etc.).

• The diagrams provided are simplified for greater
clarity. Protections and other accessories required by
standards are not illustrated.
Standard UTE NF C15-100 and good practice must
be complied with. Connected or nearby equipment
must not generate excessive interference (directive
2004/108/EEC).

Warning

- 3 -- 2 -

Contents

Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HEATING APPLICATION

Connection to the heating . . . . . . . . . . . . . . . . 8

Associating the receiver

with a transmitter thermostat . . . . . . . . . . . . . 10

Associating the receiver

with a door/window opening detector . . . . . . . 10

Simple lighting mode . . . . . . . . . . . . . . . . . . . 11

with an associated TYXIA transmitter . . . . . . 12

with an associated TYXAL detector . . . . . . . . 15

with an associated TYXAL control unit . . . . . . 16

with an associated TYDOM transmitter . . . . . . 17

CONTROL SYSTEM APPLICATION
Pulse mode (remote control switch,

garage door, electric gate) . . . . . . . . . . . . . . . 18

Removing all associations . . . . . . . . . . . . . . . . 20

Technical features . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 22

- 5 -- 4 -

Presentation

TYXIA RF 642 may be used for two types of
application:

- Control of automatic devices: lighting, a garage door
or an electric gate,

- Heating control: associated with a transmitter thermo­stat, it can be connected to a boiler or used to control
an electric heating system (via a contactor).

The receiver must be placed near the automated
device control (electrical switchboard) or heating
control (burner or thermostat input for a boiler,
electrical switchboard when used with a contact
switch).

To avoid interference with the radio transmission,
the antenna must be free from any metallic elements
(cables, electrical switchboard, metallic covers).

The receiver power supply must be provided through
an electrical cable connected to the 230 V mains.

Location

Antenna

Button

Removable
cover

LED

- 7 -- 6 -

Removing the cover

To remove the cover, push the
tab and lift the cover.

Attachment with screws

Mounted on a wall using the
screws and plugs supplied.

Mounting by double-sided
adhesive tape

Mounted on a wall using the double­sided adhesive tape supplied.
Ensure that the surface on which the
tape is applied is thoroughly clean
before mounting.

Connection

To connect the control wires, r un the
wires along the raceway provided or
by piercing the hole at ➊.
Refer to the section that deals with
your type of installation.

When the connection is made, fit the
cover and switch on the current at
the circuit breaker.

Mounting

2

1

1

- 9 -

Connecting a boiler
without thermostat
input

If the boiler does not have a
thermostat input, you can
directly control the circulator
located next to the boiler.

To control electr ic
convectors, you MUST use
a power contact switch that
is suitable for the total power
to be controlled.

Connection to the heating

- 8 -

Connecting a boiler with thermostat input

Connect receiver terminals 3 and
4 to both terminals of the boiler
thermostat input.

If necessary, remove the shunt (electric wire)
connecting the two
thermostat input
terminals.

If the boiler has a clock
input, do not mistake it
for the thermostat input.

boiler

230V

boiler
thermostat
input

Example of a boiler

terminal box

do not mistake for

the clock input

(on some boiler

models)

the shunt

wires to be

connected to

the receiver

remove

mains supply

230V/50Hz

convector(s)

L
N

N

L

power supply of the

contact switch coil

contact switch (not
supplied) fitted in the
electrical switchboard

circulator

230V

OR

N

230V

power supply

230V/50Hz

convector(s)

direct convector

control if power

< 3000 W

L

N

- 11 -

Simple lighting mode

Connection

Operation on the TYXIA RF 642

Pressing the button on the receiver changes the
current state (on or off).

Inverting the relay contact position

During an On command: the relay closes.
During an Off command: the relay opens.
You can invert the operation of the relay by pressing
the relevant button on the receiver for about
10 seconds.

- 10 -

On the receiver, press the button until the LED flashes
(~3 seconds).

Put the transmitter into association mode
(see transmitter guide).
Check that the receiver LED is no longer flashing.
The receiver is associated with the transmitter.

Associating the receiver with a transmitter
thermostat

When associated with the receiver, a door/window open­ing detector can prompt the heating to switch automati­cally to frost protection whenever a window is opened,
for example.

On the receiver, press the button until the LED flashes
(~3 seconds).
On the door/window opening detector, press the test
button.
Check that the receiver LED is no longer flashing.
The door/window opening detector is associated with
the receiver.

Associating the receiver with a
door/window opening detector

Mains

230 V

For lighting, the maximum power controlled
directly is 300 W. Above 300 W, a contact
switch must be used.

300 W

max.

Contact

switch

Command sent

On
Off

Contact Inverted contact

ON

OFF

OFF

ON

- 13 -

On the transmitter, press and hold the button
down for approximately 5 seconds.
The button will light up, go out then light up again.
Release.

Check that the receiver’s LED is no longer flashing.

The transmitter button is associated with the
receiver.

Associate the buttons with the
receiver

On the receiver, press the button until the LED flashes

(~3 seconds).You now have two options.

Slow flashing: simple lighting mode

Quick flashing: pulse mode
Press the receiver button to switch from one rate of
flashing to the other.Select the slow flashing option.

On the transmitter, press and hold the and
buttons down together for approximately 5 seconds.

The buttons will light up, go out, then light up again.
Release. Check that the receiver’s LED is no longer
flashing.

The transmitter buttons and are associated
with the receiver.

- 12 -

The simple lighting mode can be controlled by a TYXIA
transmitter (transmitter switch, key ring remote control,
etc.).

Associate the button with the
receiver

On the receiver, press the button until the LED flashes

(~3 seconds).You now have two options.

Slow flashing: simple lighting mode

Quick flashing: pulse mode
Press the receiver button to switch from one rate of
flashing to the other.Select the slow flashing option.

Simple lighting mode with an associated
TYXIA transmitter

Each function of the receiver can record up to a
maximum of 8 associations (buttons, transmitters, etc.).

OffOn

OffOn

OffOn

OR

Either is possible,

depending on the scenario.

- 15 -

The simple lighting mode can be associated with a
TYXAL detector (opening, movement, technical fault,
etc.).

On the receiver, press the button until the LED flashes
(~3 seconds).
On the detector, press the Test key (emits a beep).
Check that the receiver’s LED is no longer flashing.

The detector is associated with the receiver.

The receiver can record up to a maximum of 8
associations (buttons, transmitters, etc.).

Simple lighting mode with an associated
TYXIA transmitter

- 14 -

Associate the button with the
receiver

On the receiver, set the appliance to the required sta-

tus (e.g. light off), then press the button until the LED
flashes (~3 seconds).Yo u n ow have t wo options.

Slow flashing: simple lighting mode

Quick flashing: pulse mode.
Press the receiver button to switch from one rate of
flashing to the other.
Select the slow flashing option.

On the transmitter, press and hold the button
down for approximately 5 seconds.
The button will light up, go out then light up again.
Release.
Check that the receiver’s LED is no longer flashing.

The transmitter button is associated with the
receiver.

One button (scenario) can control different
receivers simultaneously (roller shutters, dimmer, sim­ple lighting, etc.).

Simple lighting mode with an associated
TYXAL detector

ON OFF

Lights switch on
following detection

ON OFF

Lights switch on
following detection

Lights switch off
90 seconds after
the last detection

Lights switch off at
the end of detection

- 17 -

The simple lighting mode can be associated with a
TYDOM transmitter.

To associate the receiver with TYDOM devices, please
refer to the respective guides.

- 16 -

The simple lighting mode can be associated with
a TYXAL alarm control unit.

On the control unit, enable the Maintenance
mode (see control unit guide).

On the receiver, press the button until the LED flashes
(~3 seconds).

Slow flashing:

➪

alarm status transfer

- Light on when the control unit is in surveillance
mode

- Light off when the control unit is not in surveillance
mode.

Quick flashing:

➪

transfer of alarm surveillance activation/deactivation

- set to surveillance mode: lights flash once

- disabling surveillance mode: lights flash twice

Press the button to switch from one rate of flashing to
the other.

Press the “Test” button of the control unit.
Check that the receiver’s LED is no longer flashing.

The control unit is associated with the receiver.

Simple lighting mode with an associated
TYXAL control unit

Simple lighting mode with an associated
TYDOM transmitter

TYDOM3 xx telephone transmitter

TYDOM 3xx enables the ON/OFF
feature to be operated remotely.

TYDOM 2xx multifunction remote control

TYDOM 2xx brings together all the
functions of the TYXIA buttons:

- 19 -

Operation with an associated TYXIA or TYDOM
transmitter

On the receiver, press the button until the LED flashes
(~3 seconds).
You now have two options.
Slow flashing: simple lighting mode

Quick flashing: pulse mode

Press the receiver button briefly to switch from
one rate of flashing to the other.
Select the quick flashing option.
On the transmitter, press and hold the button
down for 5 seconds.
The button will light up, go out then light up again.
Release.
Check that the receiver’s LED is no longer flashing.

The transmitter button is associated with
the receiver in pulse mode.

To associate a TYXIA RF 642 with a TYDOM 2xx,
please refer to the TYDOM 2xx guide.

The pulse mode can only be controlled by a
(TYXIA) or (TYDOM 2xx) button.

Pulse mode (remote control switch, garage
door, electric gate)

- 18 -

Connection

Operation on the TYXIA RF 642

Pressing the button on the receiver changes the
current state (on or off).

IMPORTANT:To use the receiver in pulse mode, it
must be associated with a transmitter.

Mains

230V

Remote switch

Control of an

opening (for

example: a gate).

OR

(status being modified)

- 21 -

Technical features

• Power supply: 230 V, 50 Hz +/-10%

• Class II insulation

• Consumption: 0.5 VA

• Maximum power: 16 A 230 Veff Cos ϕ= 1
or 300 W max.for lighting control

• Radio frequency 868 MHz (standard EN 300 220)

• Wireless range 100 to 300 metres outside,
variable depending on the associated
equipment (the range can be altered depending
on the installation conditions and the
electromagnetic environment)

• Number of transmitters that may be associated with
the receiver: 8 max.

• Automatic action: type 1.C (brownout)

• Operating temperature: -5°C to +50°C

• Storage temperature: -10 to +70°C

• Dimensions: 120 x 54 x 25 mm

• Protection index: IP 44 - IK 04

• Install in an environment with normal pollution lev­els

- 20 -

Press and hold the button.
The LED flashes after 3 seconds.
Keep holding down the button.
The relay reverses after 10 seconds and the LED no
longer flashes.
Keep holding down the button.
The LED flashes after 30 seconds; all the associations
are removed.
Release the button.

Removing all associations with the
receiver

- 23 -- 22 -

Troubleshooting

You cannot associate a transmitter with your
receiver.

The maximum number of transmitters that can be associated
with a receiver function is 8.

Check that this number has not been reached.

Lights only come on for 1 second each time a button is
pressed.

Pulse mode is enabled.

Put the unit into simple lighting mode (refer to the “Simple
lighting mode” section).

The receiver does not recognize the command from a
transmitter.

• The transmitter is not associated with the receiver.

• The receiver is still in association mode.

• The transmitter batteries are low.

No LED lights up on the receiver.

The receiver is not powered.

Check the receiver power supply line.

You want to associate the receiver again

.

You must star t by removing all the wireless associations
(pulse, simple lighting or roller shutters mode)