Delta GBR100 Installation And Operating Manual

MODEL: GBR100

Pag

e 1.

INSTALLATION AND OPERATING INSTRUCTIONS

VENTILATION FAN
READ AND SAVE THESE INSTRUCTIONS

GENERAL SAFETY INFORMATION

1. Make sure that the electric service supply
voltage is AC 120V, 60Hz.

2. Follow all local electrical and safety codes, as
well as the National Electrical Code (NEC) and
the Occupational Safety and Health Act (OSH
Act).

3. Always disconnect the power source before
working on or near the ventilating fan, motor or
junction box.

4. Protect the power cord from sharp edges, oil,
grease, hot surfaces, chemicals or other
objects.

5. Do not kink the power cord.

6. Do not install the unit where ducts are
configured as shown in Fig. A.

7. Provide suction parts with proper ventilation.

8. This unit is UL listed for use over a bathtub or
shower when installed in a GFCI protected
branch circuit.

9. These ventilating fans are intended for
residential usage only.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:

1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact
the manufacturer.

2. Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.

3. Installation work and electrical wiring must be
done by a qualified person(s) in accordance
with all applicable codes and standards,
including fire-rated construction.

4. Sufficient air is needed for proper combustion
and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards
such as those published by the National Fire
Protection Association (NFPA), and the
American Society for Heating Refrigeration and
Air Conditioning Engineers (ASHRAE) and the
local code authorities.

5. When cutting or drilling into the wall or ceiling,
do not damage electrical wiring and other
hidden utilities.

6. Ducted fans must always be vented to the
outdoors.

7. If this unit is to be installed over a tub or show er,
it must be marked as appropriate for the
application and be connected to a GFCI
(Ground Fault Circuit Interrupter) – protected
branch circuit.

8. Do not use this unit with any other solid-state
control device. Solid-state controls devices may
cause harmonic distortion, which can cause a
motor humming noise.

9. NEVER place a switch where it can be reached
from a tub or shower.

10. Not to be installed in a ceiling thermally
insulated to a value greater than R40. (This is
required for installation in Canada only).

Turning angle too large Duct shrink

Too many elbows Elbow near the body

Body

CAUTION

1. For general ventilating use only. Do not use to

exhaust hazardous or explosive materials and
vapors.

2. Not for use in cooking areas. (Fig. B)

3. This product must properly connect to the

grounding conductor of the supply circuit.

4. To reduce the risk of injury to persons, install

the fan at least 7 feet (2.1m) above the floor.

4

5

Cooking area

4

5

Do not install above or

inside this area

Cooking
Equipment

floor

SUPPLIED ACCESSORIES

Part name Appearance Quantity

Grille

1

Fan

1

Housing

1

Duct

Connector

(4”)

1

Screw

(ψ4×25)

4

1. INSTALLATIONS

MOUNT HOUSING WITH FLANGE:
1-1. To bend the housing tabs out to 90 degree and

make housing tabs contact the bottom of the
joist.

Tabs

Joist

1-2. The housing mounts with 4 screws (ψ4×25).

Screw housing to joist through lowest holes in
each mounting flange, then through the other
holes.

Screw 4×25

Joist

USING SUSPENSION BRAKETS (SOLD
SEPARATELY)

1-3. Sliding suspension brackets available to allow

for your specific positioning of housing
anywhere between joists and span up to 24”.

1-4. Insert suspension brackets into the channels on

housing. Make sure tabs face “up” shown.

Channel

Suspension Bracket
(Sold separately)

Tab Face

1-5. Extend suspension brackets to the width of the

joists. Hold fan in place with the suspension
brackets tabs wrapping around the bottom of
joist.

1-6. Fasten suspension brackets to joists with nails

or screws through holes near nails.

1-7. Secure suspension brackets together with

screws.

Joist

Joist

Bottom of Joist

Screw

Fig. A

Fig. B

MODEL: GBR100

Pag

e 2.

2. DUCT CONNECTION

2-1. Insert the duct into the duct connector and tape

all ductworks connection to make them secure
and air tight.

2-2. Install the duct with a gradient 1°~2° to the

outside.

Inside

Outside

Duct

Body

Gradient
1°~2°

Ceiling

Grille

Tape

Duct Connector

3. CONNECT WIRING

3-1. Follow all local electrical and ANSI/NFPA70.
3-2. NEVER place a switch where it can be reached

from a tub or shower.

(BLK)

FAN

WHTBLK

FAN
SWITCH

BLK
WHT

GRD

LIGHT/FAN ELECTRICAL BOX

LINE

IN

HOUSE ELECTRICAL BOX

3-3. Connect wires as shown in wiring diagrams.
3-4. Using wire nuts (not provided), connect house

power cable to ventilating fan.

3-5. 14 AWG (2.1 mm

2

) is the smallest conductor that

shall be used for branch-circuit wiring.

4. TEST RUN & GRILLE ATTACHMENT

4-1. When the power on, check for abnormal vibration

or sound.

4-2. Insert the mounting springs into the slots and

mount the grille to the fan unit.

Grille

Spring

Slots

5. OPERATION

Turn on the power switch to operate ON or OFF, and
LED indicator is green.

6. MAINTENANCE

WARNING:
Disconnect power source before working on unit.

Routine maintenance must be done every year.
CAUTION:

1. Never use gasoline, benzene, thinner or any
other such chemicals for cleaning the ventilating
fan.

2. Do not allow water to enter motor.

3. Do not soak resin parts in water over 60°C.

CLEANING：

1. Pull down the spring to remove grille.

2. Wash and clean grille. (Use non-abrasive kitchen
detergent, wipe dry with new cloth.)

3. Using a cloth dampened with non-abrasive
kitchen detergent, remove dust and dirt from
ventilating fan. Wipe dry with new cloth.

4. Replace grille.

DIMENSIONS

10

.7

5

"

1

0

.

7

5

"

8

"

8

.

2

5

"

5.75"

4" DUCT

8.25"

5.75"

1"

10.75"

10.75"

SPECIFICATIONS

Model No.

Voltage

(V)

Frequency

(Hz)

Powe

r

@ 0.1SP

(W)

A

ir Flow

@ 0.1SP

(CFM)

Weight

(lb.)

GBR100

120 60 12.6 100 5.6

Note: Design and specifications subject to change without notice.

WARRANTY

DELTA ELECTRONICS THREE YEAR LIMITED

WARRANTY

Delta Electronics Inc. (“Delta Electronics”) warrants
to the original consumer purchaser in the USA that
the Breez ventilation fan products will be free from
defects in material or workmanship. This warranty
is limited to three (3) years from the original d ate of
purchase.

Limitations and Exclusions

1. During the warranty period, a replacement for
any defective product will be supplied free of
charge for installation by the consumer. The
warranty provided herein does not cover charges
for labor or other costs incurred in the
troubleshooting, repair, removal, and installation
service.

2. All returns of defective parts or products must
include the product model number, and must be
made through an authorized Delta Electronics
distributor. Authorized returns must be shipped
prepaid. Repaired or replacement products will
be shipped by Delta Electronics F.O.B. shipping
point.

3. Delta Electronics shall not be liable for any
indirect, incidental, consequential, punitive, or
special damages arising out of or in connection
with products use or performance, regardless of
the form of action whether in contract, tort
(including negligence), strict product liability or
otherwise.

4. This warranty does not extend to fluorescent
lamp starters and tubes.

5. The warranty does not cover if user does not
comply with manufacture’s installation manual.

6. To qualify for warranty service, you must notify
Delta Electronics at the address or telephone
number below.

7. Delta Electronics shall have no liability to the
original owner-user with respect to any defect
caused by abuse, misuse, neglect, improper
transportation or storage, improper testing,
improper installation, improper operation,
improper use, improper maintenance, improper
repair, improper alteration, improper
modification, tampering or accident of products
or parts thereof, or unusual deterioration or
degradation of products or parts thereof due to a
physical environment beyond the requirements
of products’ specifications.

Address:4405 Cushing Parkway, Fremont, CA
94538 US Toll Free Number: 1-888-979-9889