Delta AGC7648A, AGC7648S Installation Manual
Delta Networking – Agema Family
AGC7648 Deep-Buffer Switch
- AGC7648A
- AGC7648S
Installation Guide
ii
AGC7648 Deep-Buffer Switch
Copyright
All specications and gures are subject to change without prior notice. Actual products may look
different from the photos.
All trademarks and logos mentioned in this guide are the properties of their respective holders.
Copyright © Delta Products Corporation. All rights reserved.
Regulatory and Safety Information
This product has been tested in accordance to, and complies with the following safety standards and
electromagnetic compatibility (EMC) inspection standards.
Emissions
Applicable standard
• AS/NZS CISPR 22: Class A
• ICES-003, Issue Class A
• EN 55022: Class A
• VCCI Class A
• FCC CFR 47 Part 15, Subpart B Class A
Safety
Applicable standard
• EN 60950-1, Second Edition
• UL/CSA 60950-1, Second Edition
• IEC 60950-1, Second Edition Including All National
Immunity
Applicable standard
• EN 300 386, EMC for Network Equipment
• EN 55024:
• EN 61000-3-2: Harmonic Current Emissions
• EN 61000-3-3: Voltage Fluctuations and Flicker
• EN 61000-4-2: ESD
• EN 61000-4-3: Radiated Immunity
• EN 61000-4-4: EFT
• EN 61000-4-5: Surge
• EN 61000-4-6: Low Frequency Conducted Immunity
• EN61000-4-8: Power Frequency magnetic eld
• EN61000-4-11: Voltage dips and interruptions
RoHS
Applicable standard All AG-Series components are EU RoHS compliant
Warning: Fiber Optic Port Safety
When using a ber optic port, never look at the transmit laser while it is powered
on. Also, never look directly at the ber TX port and ber cable ends when they are
powered on.
iii
Table of Contents
Table of Contents
Chapter 1: Introduction -------------------------------------------------------------------1
1.1 Overview ------------------------------------------------------------------------------------ 1
1.2 Package Content -------------------------------------------------------------------------- 1
1.3 Features ------------------------------------------------------------------------------------- 2
Chapter 2: Appearance and Mechanism --------------------------------------------3
2.1 Product Overview ------------------------------------------------------------------------- 3
2.2 LED Identication ------------------------------------------------------------------------- 4
2.3 System Requirements ------------------------------------------------------------------- 6
2.4 Data Center Deployment ---------------------------------------------------------------- 7
2.5 Power Supply Modules ------------------------------------------------------------------ 8
2.6 Fan Tray Module -------------------------------------------------------------------------- 8
Chapter 3: Installation ---------------------------------------------------------------------9
3.1 Mounting ------------------------------------------------------------------------------------ 9
3.2 Installing an Optional SFP+/QSFP/QSFP28 Transceiver ---------------------11
3.3 Connecting to the Console Port ------------------------------------------------------12
3.4 Connecting to a Power Source -------------------------------------------------------12
Chapter 4: Making the Network Connections ----------------------------------- 15
4.1 Twisted-pair Connections --------------------------------------------------------------15
4.2 Fiber Optic Connections ---------------------------------------------------------------16
4.3 Ethernet Cabling -------------------------------------------------------------------------17
Appendix 1 : Technical Specifications --------------------------------------------- 18
Appendix 2 : Warranty ------------------------------------------------------------------- 19
Limited and Support Warranty -------------------------------------------------------------19
Technical Support -----------------------------------------------------------------------------19
1
AGC7648 Deep-Buffer Switch
Chapter 1: Introduction
1.1 Overview
The AGC7648 is a ToR/Leaf and EoR switch with deep buffers for Data Center Networks, as
well as Carrier network deployments. AGC7648 is not only offering 100GbE uplink ports but
also supporting virtualization features. Total I/O bandwidth is 800G and the oversubscription
ratio is up to 1.35:1. The switch will provide customers x86-based CPU as modular design
which offers the exibility for upgrading CPUs. The switch is SDN capable and will support
choices of NOS from third party software companies and as well as ONIE, OpenFlow for
today’s open network ecosystem. It also provides comprehensive capability on layer 2 and
layer 3 features, including SNMP, Spanning Tree, VLAN, QinQ, Trunk, QoS, RIP, OSPF,
IGMP, DVMRP, PIM-DM, PIM-SM, Access Control, etc. This product which aims for Data
Center and Carrier Networks also supports advance features such as MPLS, TRILL, PFC,
VEPA, QCN, VxLAN and NVGRE to meet Data Center high performance and virtualization
requirement.
1.2 Package Content
After unpacking this switch, check the contents to be sure you have received all the
components. Then, before beginning the installation, be sure you have all other necessary
installation equipment.
• AGC7648 series switch: AGC7648A or AGC7648S
• 1 x AC power supply for AC version or 1 x DC power supply for DC version
• Rack-mounting kits
• 2 x Velcro strips
• Installation guide
If any item is missing or damaged, contact the vendor immediately, see “Technical Support”.
2
• IntroductionChapter 1
1.3 Features
The following lists the main features of the AGC7648 switch:
• 48 x 10GbE SFP+ ports
• 6 x 100GbE QSFP28 ports
• 1 x OOB Management
• 1 x Console port (RJ-45 type)
• 1 x USB port
• Hot plugging redundant power supply support
• 4 Fan modules
• Power supply LED / System / FAN status LED indication
• Extensive system LED and per port LEDs
• On board high performance CPU system with large memory
• Internal power supply; Max power 800W
• 800Gbps full-duplex switching
• 4GB GDDR5 of packet buffer memory
• External TCAM for extending classication database
• VxLAN and NVGRE tunneling support in hardware for network virtualization
• Pre-loaded with Open Network Install Environment (ONIE) for automated loading of
compatible SwitchOS software
3
AGC7648 Deep-Buffer Switch
Chapter 2: Appearance and Mechanism
2.1 Product Overview
2.1.1 Front View
Management port x 1
Console port x 1
QSFP28 port x 6
SFP+ port x 48
(Figure 2-1: Front View)
2.1.2 Rear View
PSU x 1
4 Fan tray slots
Reset x 1
Secondary PSU
slot x 1 (optional)
USB port x 1
(Figure 2-2: Rear View)
NOTE:
The switch supports up to two PSUs. However, it is shipped with one power supply
pre-installed in the rear panel of the switch. You may purchase an additional PSU for
redundancy.
4
• Appearance and MechanismChapter 2
2.2 LED Identification
This section provides an overview of the front and rear LEDs.
2.2.1 Front LEDs
Upper SFP+ Port LED
Lower SFP+ Port LED
Upper QSFP28 Port LED
Lower QSFP28 Port LED
Power LED
System LED
Fan LED
(Figure 2-3: Front LED Identification)
LED Description
System LED
• Off – No power
• Blinking Green – Booting, or System in Diagnostic mode
• Solid Green – Normal operation
• Solid Yellow – Critical alarm
• Blinking Yellow – Non-critical alarm
Power LED
• Solid Orange – Booting
• Off – Power is disconnected
When NOS is running:
• Solid Green – 2 Power Supplies are supplied to the switch and operating
normally
• Solid Yellow – Single power supply is installed and operating
• Blinking Yellow – 2 Power Supplies are installed, but only single power
supply is operating
Fan LED
• Solid Green – FAN is operating normally
• Solid Yellow – FAN is failed including incompatible airow direction
5
AGC7648 Deep-Buffer Switch
LED Description
10G SFP+ slots
Link LED (Left)
• Off – No link
• Solid Green – A valid 10Gbps link
• Solid Yellow – A valid 1G link
Act LED (Right)
• Off – No link
• Solid Green – A valid 10Gbps link
• Solid Yellow – A valid 1G link
• Blinking Green – Packet transmission or reception in progress
100G QSFP28
slots
LED1 (Solid Lighting – Linkup; Blinking – Activity)
• Solid Green – 100G Operation
• Solid White – 50G Operation
• Solid Amber – 40G Operation
• Solid Blue – 25G Operation
• Solid Purple – 10G Operation
• Off – No Link
LED 2 and 4 (Solid Lighting – Linkup; Blinking – Activity)
• Solid Blue – 25G Operation
• Solid Purple – 10G Operation
• Off – No Link
LED 3 (Solid Lighting – Linkup; Blinking – Activity)
• Solid White – 50G Operation
• Solid Blue – 25G Operation
• Solid Purple – 10G Operation
• Off – No Link
*LED2-4 (working in breakout)
Management port
Link LED
• Off – No link is established on the port
• Solid Yellow – A valid link at 10/100Mbps is established on the port
• Solid Green – A valid link at 1000Mbps is established on the port
• Blinking Green – Packet transmission or reception in progress
Act LED
• Off – No link is established on the port
• Blinking Green – Activity, transmitting or receiving packet at this port
Loading...