Delta ADP-40MH-BDA Schematic

SPECIFICATION FOR APPROVAL
Customer : MSI Part No : S93-0408120-D04 Rev : Description : ADAPTER Delta Model No : ADP-40MH BDA Rev : 03 Sample Issue Date : Jun 10 ,2009
3, Tung Yuan Road
Chungli Industrial Zone.
Taoyuan Hsien 320, Taiwan, R.O.C
Internet : http:/www.deltaww.com TEL:886-3-4526107 FAX:886-3-4343617
TABLE OF CONTENTS
1. Revision History
2. Electrical Specification
3. Schematic
4. PCB Artwork
5. Physical Dimension
6. Label Drawing
7. Packing
8. BOM (Part List)
9. Safety License
10. HI-POT & Insulation Resistance Specification
Please send one copy of this specification back after you signed approval for production pre-arrangement.
Approved By :
Date :
Engineer By: Jeason Cheng M.Engineer By: Aaron Yang Approved By: Jimmy Chiang_
1. Revision History
DELTA P/N ADP-40MH BDA SHEET 1 OF 1
CONTENT Revision History DATE Jun. 10 ,2009
1.Revision History
REV. DESCRIPTION ENGINEER DATE
---------------------------------------------------------------------------------------------------------------­ 00 ISSUE . Jeason Cheng 04/15/2008
01 CHANGE LABEL Aaron Yang 06/20/2008
02 Add HI-POT & IR Specification Jeason Cheng 02/10/2009 03 Change Spec. Label Aaron Yang 06/10/2009
2. Electrical Specification
Table Of Contents
1. Electrical
1.1 Input Characteristics Page
1.1.1 Nominal Voltage…………………………………….…………..…………….…………………… 4
1.1.2 Input Voltage Range………………………………….………………………….……………….. 4
1.1.3 Rated Frequency……………………………………………………………….………………….. 4
1.1.4 Frequency Range……………………………………………………………….…………………. 4
1.1.5 Input current ……………………………………………………………………………………… 4
1.1.6 Inrush Current Limit(cold start)…………………………………………………………………….4
1.1.7 Efficiency ………………………………………………………………………...………………….4
1.1.8 No Load Power Consumption………………………………………………..…………. .…….….5
1.1.9 Small Load Power Consumption………………………………………………………………….. 5
1.2 Output Characteristics
1.2.1 Rated Voltage……………………………………………………………………………..……….. 5
1.2.2 Voltage Range ……………………………………………………………………………………...5
1.2.3 Current………………………………………………………………….……………….…………...5
1.2.4 Output Ripple and Noise………………………………………………………………………….. 5
1.2.5 Turn On delay time………………………………………………………………………………… 6
1.2.6 Hold – up Time…………………………………………………………………………………….. 6
1.2.7 Rise time…………..………………………………………………………………………………. 6
1.2.8 Surge load:…….………………………………………………………………………………….. 6
1.2.9 Load transient response…………………………………………………………………………. 6
1.2.10 Protection………………………………………………………………………………………….. .6
1.2.10.1 Over Voltage Protection…………………………………………………………………..6
1.2.10.2 Over Current Protection…………………………………………………………………..6
1.2.10.3 Short Circuit Protection……………………………………………………………….…..7
1.2.10.4 Over Temperature Protection…………………………………………………………… 7
1.2.11 Capacitance load…………………………………………………………………………………...7
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 2 OF 10
2. Environmental
2.1 Temperature………………………………………………………………………………….…………….. 7
2.2 Humidity …………………………………………………………………………………………………….. 7
2.3 Immunity………………………………..…………………………………………………………………… 8
2.3.1 Lightning Surge Immunity………………………………………………………………………… 8
2.3.2 Electric Fast Transients (EFT)…………………………………………………………………… 8
2.4 Electrostatic Discharge (ESD)………..………………………..………………………………………….. 8
2.5 Surface Temperature rise……..…………………………………………………………………………….8
2.6 Dielectric Withstand Voltage (HI-POT)……..……………………………………………………………. 8
2.7 Leakage Current.…………………………….…………………………………………………………….. 9
2.8 Insulation Resistance……………………………….……………………………………………………… 9
2.9 Electromagnetic Interference (EMI).…..…………………………………………………………………. 9
2.10 MTBF………………………………………………………………………………………………………… 9
Mechanical
3.
3.1 Outline Dimension……………………………………………………………………………….…………. 10
3.2 AC Inlet type………………………………………………………………………………………………… 10
3.3 DC Cable Length……………………………………………………………………………….…………… 10
3.4 DC Connector Dimension..………………………………………………………………………………… 10
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 3 OF 10
1. ELECTRICAL
1.1 Input Characteristics:
1.1.1 Nominal Voltage
It is normal for 100 ~ 240Vac input AC voltage.
1.1.2 Input Voltage Range
The Adapter shall operate from 90 ~ 264Vac.
1.1.3 Rated Frequency
It is normal for 50Hz or 60Hz and single phase.
1.1.4 Frequency Range
The Adapter shall operate with an input frequency from 47 Hz to 63 Hz.
1.1.5 Input Current
1.2A Max at 100Vac input voltage.
1.1.6 Inrush Current Limit (cold start)
(a) 110A/1msec. (Maximum at full loading when Vin=AC 90V, 50/60Hz) (b) 220A/1msec. (Maximum at full loading when Vin=AC 180V, 50/60Hz)
1.1.7
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
Efficiency (Warm Up)
1.1.7.1
1.1.7.2 Active mode efficiency:
min. at nominal input voltage, maximum load and measured at the end of DC cable.
84 %
More than 83.2% of average efficiency of 25%,50%,75% and 100% load tested at 115Vac and
Vac. (Warm up after 30 minutes)
230
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
File Name:DF-PSLA4V-2R00.DOC SHEET 4 OF 10
REV.
S00
1.1.8 No Load Power Consumption
Maximum non-load power consumption is less than
1.1.9 Small Load Power Consumption
Vin=115Vac/60Hz and 230Vac/50Hz
Output load(W) Input power (max)
1W 1.7W
1.5W 2.4W
1.2 Output Characteristics:
1.2.1 Rated Voltage
The rated output voltage is specified at 20V.
1.2.2 Voltage Range
The output voltage will be performed 19.5V~ 21.5V when the load is 0A ~ 2A steadily.
1.2.3
Current
This Adapter can work from 0A to 2A and output voltage is in section 1.2.2 specified range.
0.5W
at
115Vac/60Hz and 230Vac/50HZ
1.2.4
Measured methods: T1. Performed by 20M Hz bandwidth in oscilloscope. T2. Applied 0.1uF high frequency capacitor and 47uF electrolytic capacitor across output connector terminals. T3. Measured at the end of DC cable.
T4. 47Hz and 63Hz tested at 90Vac and 264Vac.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
Output Ripple and Noise
Output ripple voltage is 350 mV peak to peak or less.
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 5 OF 10
1.2.5 Turn On delay time
The Adapter shall switch on in less than
1.2.6 Hold –up time
The output voltage shall be sustained 6mS within regulation requirement after loss 100Vac and maximum load.
1.2.7 Rise time DC output rise time from 10% to 90% of output voltage shall be less than 40ms at nominal line and maximum load
1.2.8 Surge load: The adapter shall support 2.5A for
1.2.9 Load transient response The adapter must within regulation when applied a step load from 0% to 50% and 50% to 100%
load at The output voltage
0.5A/us
slew rate and 10mS time period.
will be performed 19.5V~ 21.5V.
2 seconds
60S
at input voltage is 100Vac.
at 100 ~ 240Vac and 25℃.
1.2.10 Protection
1.2.10.1 Over Voltage Protection
The output shall be protected to latch off at over-voltag e condit ion, ma xim um val u e ca n’t be o ver 26V. That might be return to normal state by AC reset, reset 2 Minutes.
1.2.10.2 Over Current Protection
The maximum constant current shall be less than 4A.
The ADAPTOR SHALL BE AUTO-RECOVERY.
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 6 OF 10
1.2.10.3 Short Circuit protection
Output can be shorted without damage. The adaptor shall be auto-recovery. (It will enter into normal condition when the fault condition is removed.)
1.2.10.4 Over Temperature Protection
No deformation and no discoloration on case and will be shut down. That will be return to normal state by ac reset, reset2 minutes.
1.2.11 Capacitance load
2200uF (5 times), No protection.
The adapter can supply 2200uF electrolytic capacitor charge current.
2. Environmental
2.1 Temperature
2.1.1 Operating
The AC Adapter shall be capable of operating at full load with an ambient temperature range of 0 ℃
to +40℃.
2.1.2 Shipping/Storage
The AC Adapter shall be capable of withstanding ambient temperature from
2.2 Humidity
2.2.1 Operating
The AC Adapter shall be capable of operation in relative humidity of 0% to 90% relative humidity, non-condensing.
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
若蘭 楊基祥
-20℃ to +70
℃.
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 7 OF 10
2.2.2 Shipping/storage
The AC Adapter shall be capable of withstanding ambient relative humidity of 0% to 95% relative humidity, non-condensing.
2.3 Immunity
2.3.1 Lightning Surge Immunity This is to follow the norm of IEC-61000-4-5 Level 3 requirements
L-N 1KV/1.2 L-FG 2KV/1.2
2.3.2 Electric Fast Transients (EFT) This is to follow the norm of IEC-61000-4-4/1995 (EN 61000-4-4) Level 3 requirements
2.4 Electrostatic Discharge ( ESD )
* 50uS 5 times No function error.
* 50uS 5 times No damage.
This Adapter is capable to withstand ESD test voltage at any point around the enclosure as below. (Refer to IEC61000-4-2)
±15KV air discharge No damage. ±
8KV contact discharge No damage.
2.5 Surface Temperature rise
Output 40W and ambient 25℃±3;input voltage 100Vac/240Vac case temperature rise40℃.
2.6 Dielectric Withstand Voltage ( HI – POT )
100% of line products of this Adapter shall be applied 3000Vac for 2 seconds between AC
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 8 OF 10
input terminals and output terminals. Cut off current is 3mA.
2.7 Leakage Current :
The AC leakage current is less than 100μA when adapter is connected to 240Vac/60Hz at normal condition.
2.8 Insulation Resistance
The insulation resistance shall be not less than 20M ohms after application of 500Vdc/10mA for 1 minute.
2.9 Electromagnetic Interference (EMI)
2.9.1 The adapter shall comply with the following national standards.
(a) CISPR 22 Class B (b)
VCCI Class B
2.10 MTBF
2.10.1 MTBF(Mean-Time-Between-Failures)Calculation
2.10.2 MTBF Verification
The calculated MTBF shall be maximum load and normal voltage.
The MTBF shall be verified from life testing performed by factory Quality department. The operating conditions are:
ranges(110VAC or 220VAC) and a minimum load of
150,000
40
hours of continuous operation at
ambient temperature, sea level ,both nominal line voltage
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
若蘭 楊基祥
25
,
75%
of the maximum load.
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
REV.
S00
File Name:DF-PSLA4V-2R00.DOC SHEET 9 OF 10
3. Mechanical
3.1 Outline Dimension:
3.2 AC Inlet type:
3.3 DC Cable Length:
3.4 DC Connector Dimension: OD= ID=
5.5
2.5
Socket C6 type
mm
mm
1800
96.0*42.0*28.7
mm
mm , Color :
Black
台達電子工業股份有限公司
DELTA ELECTRONICS, INC.
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Date Drawn Design (EE) Design (ME)
09/14/2007
若蘭 楊基祥
DESCRIPTION :
電氣規格 (Electrical Specification)
MODEL NO. :
ADP-40MH BDA
DOCUMENT NAME. :
ES-40MH BDA
File Name:DF-PSLA4V-2R00.DOC SHEET 10 OF 10
REV.
S00
3.Schematic
FB101
VANNI EVANNI E
4. PCB Artwork
5.Physical Dimension
Loading...
+ 47 hidden pages