Delta 50-850 User Manual

INSTRUCTION MANUAL

1½ H.P. Single-Stage

Dust Collector

(Model 50-850)

PART NO. 902115 - 11-15-02

Copyright © 2002 Delta Machinery

ESPAÑOL: PÁGINA 15

To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,
please call

1-800-223-7278 (In Canada call 1-800-463-3582).

2

GENERAL SAFETY RULES

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not
be modified and/or used for any application other than that for which it was designed. If you have any questions relative
to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should
be performed on the product.

Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY

1. FOR YOUR OWN SAFETY, READ INSTRUCTION

MANUAL BEFORE OPERATING THE TOOL. Learn the

tool’s application and limitations as well as the specific
hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. ALWAYS WEAR EYE PROTECTION.

Wear safety
glasses. Everyday eyeglasses only have impact resistant
lenses; they are not safety glasses. Also use face or dust
mask if cutting operation is dusty. These safety glasses
must conform to ANSI Z87.1 requirements. Note:
Approved glasses have Z87 printed or stamped on them.

4. REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it “on”.

5. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t

use power tools in damp or wet locations, or expose them
to rain. Keep work area well-lighted.

7. KEEP CHILDREN AND VISITORS AWAY. All children

and visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILDPROOF – with padlocks,

master switches, or by removing starter keys.

9. DON’T FORCE TOOL. It will do the job better and be

safer at the rate for which it was designed.

10. USE RIGHT TOOL. Don’t force tool or attachment to
do a job for which it was not designed.

11. WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught in
moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.

12. SECURE WORK. Use clamps or a vise to hold work
when practical. It’s safer than using your hand and frees
both hands to operate tool.

13. DON’T OVERREACH. Keep proper footing and
balance at all times.

14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.

16. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by Delta
may cause hazards or risk of injury to persons.

17. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in “OFF” position before plugging in
power cord.

In the event of a power failure, move switch

to the “OFF” position.

18. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is accidentally
contacted.

19. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly and
perform its intended function – check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be
properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or cutter
only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.

22.

STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE WHEN OPERATING A POWER
TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while operating

power tools may result in serious personal injury.

23. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted,
connected or reconnected.

24. THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always operate
machinery in well ventilated areas and provide for proper
dust removal. Use wood dust collection systems whenever
possible.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

3

ADDITIONAL SAFETY RULES FOR

DUST COLLECTORS

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE until it is
assembled and installed according to the instructions.

2. OBTAIN ADVICE FROM YOUR SUPERVISOR,
instructor, or another qualified person if you are not

familiar with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommended
electrical connections.

4. DO NOT leave the dust collector plugged into the
electrical outlet. Unplug dust collector from the outlet
when not in use and before servicing, changing bags,
unclogging and cleaning.

5. ALWAYS turn all controls “OFF” before unplugging
the dust collector.

6. TO REDUCE THE RISK OF ELECTRICAL SHOCK,
do not use on wet surfaces. Do not expose to rain. Store
indoors.

7. DO NOT use the dust collector to pick up
flammable or combustible liquids, such as gasoline.
NEVER use the dust collector near any flammable or
combustible liquids.

8. USE the dust collector to pick up wood materials
only. DO NOT use the dust collector to pick up metal
shavings, metal dust, or metal parts.

9. NEVER use the dust collector to dissipate fumes
or smoke. NEVER pick up anything that is burning or
smoking, such as cigarettes, matches or hot ashes.

10. DO NOT pull the dust collector by the power cord.
NEVER allow the power cord to come in contact with
sharp edges, hot surfaces, oil or grease. Do not place
anything over the top of the power cord.

11. DO NOT unplug the dust collector by pulling on the
power cord. ALWAYS grasp the plug, not the cord.

12. DO NOT handle the plug or dust collector with wet
hands.

13. REPLACE a damaged cord immediately. DO NOT
use a damaged cord or plug. If the dust collector is not
operating properly, or has been damaged, left outdoors
or has been in contact with water, take it to an
Authorized Service Center for service.

14. DO NOT use the dust collector as a toy. DO NOT
use near or around children.

15. DO NOT insert fingers or foreign objects into the
dust intake port or discharge port. Keep hair, loose
clothing, fingers, and all body parts away from openings
and moving parts of the dust collector.

16. DO NOT use with any opening blocked; keep
openings free of dust, lint, hair, and anything that may
reduce air flow.

17. NEVER use the dust collector without the dust
collection bag in place and properly secured.

18. ALWAYS use intake cover to cover dust port when
the dust collector is not in use or mounted to a
supporting surface for storage.

19. PERIODICALLY INSPECT dust bag for any cuts,
rips or tears. NEVER operate the dust collector with a
damaged bag or vacuum hose.

20. USE EXTRA CARE when cleaning on stairs.

21. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before installing
or removing accessories, before adjusting or changing
set-ups, or when making repairs.

22. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK THE
SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.

23. ADDITIONAL INFORMATION regarding the safe
and proper operation of this tool is available from the
Power Tool Institute, 1300 Summer Avenue, Cleveland,
OH 44115-2851. Information is also available from the
National Safety Council, 1121 Spring Lake Drive, Itasca,
IL 60143-3201. Please refer to the American National
Standards Institute ANSI 01.1 Safety Requirements for
Woodworking Machines and the U.S. Department of
Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

4

UNPACKING AND CLEANING

Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all
unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline
or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste
wax. ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING

OR ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY

Fig. 2

1 -Locking Bands for

Filter and Dust
Collection Bags (2)

2- Filter Bag

3- Dust Collection Bag

4 - Filter Bag Support Rod

5- Extension Rod

6- Clamps (2)

7 -6" Dia. Flexible Hose

8 -Drum Support (3)

9 -Casters (3/8"

Lockwashers,
3/8-16 Hex Nuts) (4)

10 -“U” Bracket for Filter Bag

Support Rod

11 -Lower Dust Bag

retaining Clips (4)

Fig. 3

12 -Blower and Motor

Assembly
13 -Clamp
14 -4" Dia. Flexible Hose
15 - Intake Port
16 -Base
17 -Intake Caps (2)
18 -Drum

Fig. 2

Fig. 3

1

2

3

4

5

6

7

8

9

10

12

13

14

15

16

17

18

11

HARDWARE NOT SHOWN

* -5/16"-18 x 5/8"

Hex Head Screws (20)

* - 5/16" Lockwashers (24)

* -5/16"-18 Hex Nuts (12)

* -5/16" x 7/8" O.D.

Flat Washers (6)

* - M4.2 Sheet Metal

Screws (4)

* -1/4-20x5/8" Hex Head

Screws (8)

* -1/4" Lockwashers (8)

* -1/4"-20 Hex Nuts (8)

5

ASSEMBLY

Fig. 4

Fig. 5

Fig. 6

Fig. 8Fig. 7

ASSEMBLING
CASTERS TO BASE

1. Insert threaded rod of caster (A) Fig. 4, into the hole
located on the underside of base (B) and fasten with
3/8" lockwasher (C) and 3/8-16 hex nut (D). Fig. 5,
illustrates the caster fastened to the base.

2. Assemble the remaining three casters to the
underside of the base in the same manner.

ASSEMBLING BLOWER
AND MOTOR ASSEMBLY
TO BASE

1. Turn base (A) Fig. 6, right side up. Align the
mounting holes at the base of blower and motor
assembly (B) Fig. 6, with six pre-drilled holes (C) in base
(A) and fasten with six 5/16-18x5/8" hex head screws (D)
and 5/16" lockwashers (E).

2. Fig. 7, illustrates the blower and motor assembly (B)
fastened to base (A).

3. Assemble drum support (F) Fig. 8, to the two
threaded holes in the corner of base (A), as shown in
Fig. 8, with two 5/16-18x5/8" hex head screws and
5/16" lockwashers (G). NOTE: Do not completely tighten
hardware at this time.

A

B

C

D

D

E

A

C

C

B

A

B

F

G

G

A

WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE
MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION
MANUAL.

6

Fig. 9

Fig. 10

Fig. 13

Fig. 12

4. Assemble the remaining drum supports (F) Fig. 9, to
base (A) as shown.

5. Assemble “U” bracket (H) Fig. 10, to drum (J). Place
a 5/16" flat washer then a 5/16" lockwasher onto a 5/16­18x5/8" hex head screw. Insert the hex head screw (K)
thru the hole in the “U” bracket and the hole in the drum,
thread a 5/16" hex nut onto the hex head screw and
tighten securely. Repeat this process for the remaining
hole. NOTE: “U” bracket should be mounted to the right
side of opening (L) in drum as shown.

6. Align the holes in the drum support (M) Fig. 12, with
the holes in the drum (J). Place a 5/16" flat washer on a
5/16-18x5/8" hex head screw, then 5/16" lockwasher
onto the hex head screw, insert the hex head screw thru
the hole in drum support and drum. Thread a 5/16" hex
nut onto the hex head screw and tighten securely.
Fasten the remaining drum supports to the drum (J) in
the same manner.

7. The dust collector is supplied with two 6" hose
clamps (P) Fig. 13. Place one end of 6" dia. flexible hose
(R) over blower/motor inlet (B) Fig. 14, and secure with
hose clamp (P).

8. Place the other 6" hose clamp on flexible hose and
attach the other end of the hose to drum (J) Fig. 14 in the
same manner.

Fig. 14

F

A

J

H

K

L

J

M

M

P

R

P

J

R

P

B

F

7

Fig. 15

Fig. 16

Fig. 17

9. Attach the lower dust bag retaining clip (A) Fig. 14A,
to the dust collector drum. Align the two holes (B) in the
retaining clip (A) Fig. 14A, with the two holes in the drum.
Insert a 1/4-20x5/8" hex head screw through the holes in
the retaining clip and the holes in the drum. Place a 1/4"
flat washer onto the screws, and thread 1/4-20 hex nut s
on the screws and tighten securely. Repeat this process
for the three remaining sides of the drum.

ASSEMBLING DUST INTAKE
PORT AND CAPS TO BLOWER
AND MOTOR ASSEMBLY

1. MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.

2. Align the four holes in dust intake port (A) Fig. 15,
with the mounting holes in flange (B) of blower and
motor assembly and fasten with four sheet metal screws
(C). Fig. 16 illustrates the dust intake port assembled to
the blower assembly.

3. NOTE: Two dust intake port caps (D) Fig. 17, are
supplied with the dust collector. The caps are to be
placed into the dust intake ports (E) when the intake ports
are not in use.

4. Place the collar of dust cap (D) Fig. 17, over the
opening on intake port. Press recessed side of dust cap
(D) into port opening. IMPORTANT: When connecting
an intake hose to one or both intake ports, DO NOT

REMOVE THE DUST CAP COLLARS (F) FIG. 17 FROM
THE INTAKE PORTS. Pull the dust cap from the port

opening and slide the collar and cap farther onto the
port housing.

A

B

C

E

D

E

D

F

Fig. 14A

A

B

8

Fig. 18

Fig. 19

Fig. 22

Fig. 20

Fig. 21

ASSEMBLING FILTER AND
DUST COLLECTION BAGS
TO DRUM

1. Hook the loop on the top of filter bag (A) Fig. 18,
onto filter bag support rod (B) as shown.

2. Assemble extension rod (C) Fig. 19, onto the end of
filter bag support rod (B). Raise support rods (B) and (C),
with filter bag (A) attached and place end of support rod
(C) into holes of bracket (D). NOTE: Flared end of filter
bag extension rod will prevent the rod from sliding through
bracket.

3. Position open end of filter bag (A) Fig. 19, over lip of
dust drum (E). Insert locking band (F) Fig. 20, through
the loops of filter bag (A) and fasten with clamp (G) as
shown in Fig. 21. NOTE: Make certain locking band is
positioned in the channel of drum (F) before fastening
clamp.

4. Pull up on each retaining clip (A) Fig. 22, and insert
the dust collection bag (B) underneath each retaining clip
to hold the dust collection bag in place.

5. Place the locking clamp (C) Fig. 22 around dust
collection bag and dust collector drum and lock in place.

NOTE: Make certain locking clamp is positioned in the
channel of the dust collector drum before locking clamp.

A

B

B

A

E

C

D

G

A

E

F

G

E

A

B

C

9

Fig. 23

ASSEMBLING DUST INTAKE
HOSES TO BLOWER AND
MOTOR ASSEMBLY

KEEP DUST CAPS INSTALLED AT ALL TIMES OVER
INTAKE PORTS. REMOVE A DUST CAP ONLY WHEN
A FLEXIBLE HOSE IS ATTACHED TO THE INTAKE
PORT.

The dust collector is supplied with a 4" dia. flexible dust
intake hose.

1. To assemble the intake hose (A) Fig. 23, to the blower
assembly, pull the dust cap (B) from the dust intake port
(C) and slide the dust cap collar (D) farther onto the dust
intake port (C) as shown. IMPORTANT: DO NOT RE-

MOVE THE INTAKE CAP FROM THE INTAKE PORT.

2. Place hose clamp (E) Fig. 23, on one end of flexible
hose (A) and assemble the hose to dust intake port (C).
Tighten hose clamp (E).
Should you wish to operate your dust collector with a
second intake hose, contact your local Delta Distributor to

purchase the hose and install as in STEPS 1 and 2 above.
Whenever one of the dust intake ports is not in use,
always be sure the dust cap is properly installed in the
intake port for operator safety.

ALWAYS DISCONNECT DUST COLLECTOR FROM
THE POWER SOURCE BEFORE CONNECTING OR
DISCONNECTING INTAKE HOSE.

CONNECTING TOOL TO POWER SOURCE

POWER CONNECTIONS

A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be
protected with a 20 Amp time lag fuse. Have a qualified electrician repair or replace damaged or worn cord
immediately. Before connecting the motor to the power line, make certain the switch is in the “OFF” position and be
sure that the electric current is of the same characteristics as stamped on the motor nameplate. All line connections
should make good contact. Running on low voltage will damage the motor.

WARNING: DO NOT EXPOSE THE DUST COLLECTOR TO RAIN OR OPERATE THE MACHINE IN DAMP

LOCATIONS.

MOTOR SPECIFICATIONS

Your tool is wired for 120 volt, 60 HZ alternating current. Before connecting the tool to the power source, make sure
the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.

This tool must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This tool is equipped with a cord having an equipment-grounding
conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the dust collector. If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.

120 VOLT,
SINGLE PHASE OPERATION

This tool must be grounded while in use to protect the operator from electric shock. The motor recommended for use
with your dust collector is shipped wired for 120 Volt, Single Phase, and is equipped with an approved 3-conductor
cord and 3-prong grounding type plug to fit the proper grounding type receptacle, as shown in Fig. 24. The green
conductor in the cord is the grounding wire. Never connect the green wire to a live terminal.
A temporary adapter, shown in Fig. 25, is available for connecting 3-prong grounding type plugs to 2-prong receptacles
if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded
outlet can be installed by a qualified electrician. THIS ADAPTER IS NOT APPLICABLE IN CANADA. The green­colored rigid ear, lug, etc., extending from the adapter, is the grounding means and must be connected to a permanent
ground such as to a properly grounded outlet box, as shown in Fig. 25. Whenever the adapter is used, it must be held
in place with a metal screw.

A

B

E

D

C

10

Use proper extension cords. Make sure your extension
cord is in good condition and is a 3-wire extension cord
which has a 3-prong grounding type plug and a 3-hole
receptacle which will accept the tool’s plug. When using
an extension cord, be sure to use one heavy enough to
carry the current of the tool. An undersized cord will
cause a drop in line voltage, resulting in loss of power
and overheating. Figs. 27 & 27A, shows the correct
gauge to use depending on the cord length. If in doubt,
use the next heavier gauge. The smaller the gauge
number, the heavier the cord.

EXTENSION CORDS

Fig. 24

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

HOLES

Fig. 25

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

HOLES

GROUNDED OUTLET BOX

CURRENT
CARRYING
PRONGS

GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

Fig. 26

240
volt

240 VOLT,
SINGLE PHASE OPERATION

The motor supplied with your tool is a dual voltage 120/240
volt motor. If it is desired to operate your dust collector at
240 volts, single phase, contact your local Authorized
Delta Service Center or qualified electrician for proper
procedures to rewire your dust collector motor for 240 volt
operation and wiring a 240 volt attachment plug to the
power supply cord.
The tool with a 240 volt plug should only be connected to
an outlet having the same configuration as the plug
illustrated in Fig. 26. No adapter is available or should be
used with the 240 volt plug.

AS A PRECAUTION IN ALL CASES, MAKE CERTAIN
THE RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE, HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

Fig. 27

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS

Ampere Volts Total Length of Gauge of

Rating Cord in Feet Extension Cord

0-6 120 up to 25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG
6-10 120 up to 25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG
10-12 120 up to 25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG
12-16 120 up to 25 14 AWG
12-16 120 25-50 12 AWG
12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS

Ampere Volts Total Length of Gauge of

Rating Cord in Feet Extension Cord

0-6 240 up to 50 18 AWG
0-6 240 50-100 16 AWG
0-6 240 100-200 16 AWG
0-6 240 200-300 14 AWG
6-10 240 up to 50 18 AWG
6-10 240 50-100 16 AWG
6-10 240 100-200 14 AWG
6-10 240 200-300 12 AWG
10-12 240 up to 50 16 AWG
10-12 240 50-100 16 AWG
10-12 240 100-200 14 AWG
10-12 240 200-300 12 AWG
12-16 240 up to 50 14 AWG
12-16 240 50-100 12 AWG
12-16 240

GREATER THAN 100 FEET NOT RECOMMENDED

Fig. 27A

11

OPERATING CONTROLS

WARNING: BEFORE OPERATING THE MACHINE, FOR OPERATOR SAFETY, ALWAYS MAKE CERTAIN THAT
EACH DUST INTAKE PORT (WHICH IS NOT BEING USED OR PREVIOUSLY ASSEMBLED TO A DUST COLLECTION
SYSTEM) BE COVERED WITH A DUST INTAKE PORT CAP. THE ROTATING FAN INSIDE THE BLOWER HOUSING IS
ACCESSIBLE THROUGH THE DUST INTAKE PORTS AND IS HAZARDOUS. ALWAYS WEAR PROPER APPAREL, DO
NOT WEAR JEWELRY, AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE PORTS.
FOLLOW THE SAFETY RULES STATED EARLIER ON PAGES 3 AND 4 IN THIS MANUAL.

Fig. 28

Fig. 29

ON/OFF SWITCH

The “on/off” switch is located on the side of the motor.
To turn the dust collector “ON”, push the start button
(A) Fig. 28. To turn the dust collector “OFF”, push stop
button (B).

LOCKING SWITCH
IN THE “OFF” POSITION

IMPORTANT: When the machine is not in use, the switch

(A) Fig.18 should be locked in the OFF position using a
padlock (C), with a 3/16" diameter shackle to prevent
unauthorized use.

CIRCUIT BREAKER

Your dust collector motor is supplied with a resettable circuit breaker. If the motor shuts off or fails to start due to an
overload condition, turn the dust collector switch “OFF,” let the motor cool three to five minutes, and push the reset button
(D) Fig. 29, on the circuit breaker to reset the breaker. The motor can then be turned on again in the usual manner. If the
overload continues to trip, take the dust collector to a Delta Authorized Service Center for repair.

MAINTENANCE

NOTE: Before any maintenance or service is performed, be sure the unit is disconnected from the power source to

prevent starting. All servicing other than the items recommended in this Instruction Manual should be performed by an
authorized service facility. When storing your dust collector, remove power supply cord from the electrical outlet. Coil
the cord neatly and place it off the floor on the base of the dust collector to eliminate potential cord damage.

MOTOR MAINTENANCE

Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. should
not be used as high pressure may damage insulation and blow dirt under loosened tape. The operator performing this
cleaning function should always wear eye protective goggles. Dust can cause excessive insulation temperatures.

A

B

A

C

D

12

Two Year Limited Warranty

Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which
in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. Delta may require that
electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement.
Delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or
alteration made or specifically authorized by anyone other than an authorized Delta service facility or representative. Under
no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This
warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all
other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly
disclaimed by Delta.

Printed in U.S.A.

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

ACCESSORIES

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site

www.deltamachinery.com for a catalog or

for the name of your nearest supplier.

WARNING: Since accessories, other than those offered by Delta, have not been tested

with this product, use of such accessories could be hazardous. For

safest operation, only

Delta recommended accessories should be used with this product.

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,
BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series
2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®,
JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, Midi Lathe™, MORTEN™, NETWORK™, OMNIJIG®, POCKET
CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®,
Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE­LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®,
STAIR EASE®, The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL
SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®,
UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE®, WHISPER
SERIES®, WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y
también pueden estar registradas en otros países.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE

• DELTA)

Parts and Repair Service for Porter-Cable •Delta Machinery are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

•

Delta)

Authorized Service Stations are located in many large cities. Telephone [phone] or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable

·

Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized

Service Center, or Porter-Cable

·

Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will

be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable

·

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro

de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable

·

Delta más cercano.

ARIZONA

Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: [phone]
Fax: [phone]

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: [phone]
Fax: [phone]

San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: [phone]
Fax: [phone]

COLORADO

Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: [phone]
Fax: [phone]

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: [phone]
Fax: [phone]

Tampa 33609
4538 W. Kennedy Boulevard
Phone: [phone]
Fax: [phone]

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: [phone]
Fax: [phone]

ILLINOIS

Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: [phone]
Fax: [phone]

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: [phone]
Fax: [phone]

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: [phone]
Fax: [phone]

MASSACHUSETTS

Braintree 02185 (Boston)
719 Granite Street
Phone: [phone]
Fax: [phone]

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: [phone]
Fax: [phone]

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: [phone]
Fax: [phone]

MINNESOTA

Minneapolis 55429
5522 Lakeland Avenue North
Phone: [phone]
Fax: [phone]

MISSOURI

North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: [phone]
Fax: [phone]

St. Louis 63119
7574 Watson Road
Phone: [phone]
Fax: [phone]

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: [phone]
Fax: [phone]

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: [phone]
Fax: [phone]

OHIO

Columbus 43214
4560 Indianola Avenue
Phone: [phone]
Fax: [phone]

Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: [phone]
Fax: [phone]

OREGON

Portland 97230
4916 NE 122 nd Ave.

Phone: [phone]
Fax: [phone]

PENNSYLVANIA

Willow Grove 19090
520 North York Road
Phone: [phone]
Fax: [phone]

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: [phone]
Fax: [phone]

Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: [phone]
Fax: [phone]

WASHINGTON

Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: [phone]
Fax: [phone]

Printed in U.S.A.

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: [phone]
Fax: [phone]

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: [phone]
Fax: [phone]

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: [phone]
Fax: [phone]

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: [phone]
Fax: [phone]

QUÉBEC

1515 ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: [phone]
Fax: [phone]

1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: [phone]
Fax: [phone]